Shark HPB-353007C Operator's Manual
The Shark HPB-353007C is a powerful pressure washer designed for a variety of cleaning tasks. It features a hot water system, a detergent injector, and a variable pressure control, making it ideal for tackling tough dirt and grime. The machine also comes with a variety of safety features, including a high limit thermostat, a GFCI, and a pump protector.
PDF
Download
Document
Advertisement
Advertisement
Hpb OPERATOR’S MANUAL 98011900-1 LIS T E D ® MODEL # HPB-392007A ORDER # 1.109-109.0 HPB-353007A HPB-353007B 1.109-110.0 1.109-111.0 HPB-353007C 1.109-112.0 To locate your local Shark Commercial Pressure Washer Dealer nearest you, visit www.sharkpw.com 9.801-190.0 CONTENTS 2 Introduction & Important Safety Information 4-6 Component Identifications 7 Assembly Instructions 8 Installation 9 Operating Instructions 10 Detergents & General Cleaning Techniques 11 Shut Down & Clean-up Procedures 12 Storage 12 Troubleshooting 13-14 Maintenance Charts 15 Oil Change Record 15 Preventative Maintenance 16 Maintenance & Service 17-18 Exploded View 19 Exploded View Parts List 20-21 Control Panel Exploded View & Parts List 22-23 Float Tank Option Exploded View & Parts List 24-25 Auto Start/Stop Options Exploded View & Parts List 26 Auto Start Stop - Steam Options Exploded View & Parts List 27 Pump Assembly Exploded View & Parts List 28 Steam Option, Exploded View & Parts List 29 Hose & Spray Gun Assembly Exploded View & Parts List 30 Shark HPB • 9.801-190.0 • Rev. 7/13 CONTENTS UU1 Unloader Valve Exploded View and Parts List 31 KM. 3 Pump Exploded View and Parts List 32-33 Specifications 34-35 Burner Specifications 36 KNA Burner Replacement Parts & Parts Lists 37-38 Warranty Model Number ______________________________ Serial Number ______________________________ Date of Purchase ____________________________ The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference. 3 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER INTRODUCTION & Important Safety Information Thank you for purchasing a Shark Pressure Washer. We reserve the right to make changes at any time without incurring any obligation. Owner/User Responsibility: The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this pressure washer. Warning information should be emphasized and understood. If the operator is not fluent in English, the manufacturer’s instructions and warnings shall be read to and discussed with the operator in the operator’s native language by the purchaser/owner, making sure that the operator comprehends its contents. Owner and/or user must study and maintain for future reference the manufacturers’ instructions. The operator must know how to stop the machine quickly and understand the operation of all controls. Never permit anyone to operate the engine without proper instructions. Save these Instructions This manual should be considered a permanent part of the machine and should remain with it if machine is resold. When ordering parts, please specify model and serial number. Use only identical replacement parts. nected to a power supply receptacle protected by a GFCI. DANGER: Improper connection of the equipmentgrounding conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the product - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adaptor with this product WARNING: Keep wand, hose, and water spray away from electric wiring or fatal electric shock may result. 5. To protect the operator from electrical shock, the machine must be electrically grounded. keep water spray away from It is the responsibility of the electrical wiring. owner to connect this machine to a UL grounded receptacle of proper voltage and amperage ratings. Do not spray water on or near electrical components. Do not touch machine with wet hands or while standing in water. Always disconnect power before servicing. WARNING WARNING This machine is to be used only by trained operators. Important Safety Information 4 WARNING: To reduce the risk of i n j u r y, r e a d o p e r a t i n g instructions carefully before using. 1. R e a d t h e owner's manual thoroughly. Failure to follow instructions could read operator’s cause malfunction of the manual thoroughly prior to use. machine and result in death, serious bodily injury and/or property damage. 2. K n o w h o w t o s t o p t h e m a c h i n e a n d bl e e d p r e s s u r e q u i ck l y. B e t h o r o u g h l y familiar with the controls. 3. Stay alert — watch what you are doing. 4. All installations must comply with local codes. Contact your electrician, plumber, utility company or the selling distributor for specific details. If your machine is rated 250 volts or less, single phase will be provided with a ground fault circuit interrupter (GFCI). If rated more than 250 volts, or more than single phase this product should only be con- risk of explosion: Operate only where open flame or torch is permitted WARNING: Flammable liquids can create fumes which can ignite, causing property damage or severe injury. WARNING: Risk of explosion — Operate only where open flame or torch is permitted. 6. In oil burning models, use only kerosene, No. 1 home heating fuel, or diesel. If diesel is used, add a soot remover to every tankful. WARNING risk of fire. do not add fuel when operating machine. WARNING: Risk of fire — Do not add fuel when the product is operating or still hot. WARNING: Do not use gasoline crankcase draining or oil containing gasoline, solvents or alcohol. Doing so will result in fire and/or explosion. 7. Oil burning appliances shall be installed only in locations where combustible dusts and flammable gases or vapors are not present. Do not store or use gasoline near this machine. 8. Do not allow acids, caustic or abrasive fluids to pass through the pump. 9. Never run pump dry or leave spray gun closed longer than 1-2 minutes. Shark HPB • 9.801-190.0 • Rev. 7/13 10. Keep operating area clear of all persons. WARNING use protective eye wear and clothing when operating this equipment. WARNING WARNING: High pressure spray can cause paint chips or other particles to become airborne and fly at high speeds. To avoid personal injury, eye, hand and foot safety devices must be worn. 11. Eye, hand, and foot protection must be worn when using this equipment. WARNING: This machine exceeds 85 db appropriate ear protection must be worn. ear protection must be worn WARNING Hot discharge fluid: Do not touch or direct discharge stream at persons. WARNING Risk Of Injury: Hot Surfaces Can Cause Burns Trigger Gun Kicks back - Hold with both hands risk of injection or severe injury To persons. keep clear of nozzle. WARNING: Hot discharge fluid. Do not touch or direct discharge stream at persons. WARNING: This machine produces hot water and must have insulated components attached to protect the operator. WARNING: Risk of injury. Hot surfaces can cause burns. Use only designated gripping areas of spray gun and wand. Do not place hands or feet on non-insulated areas of the pressure washer. WARNING: Grip cleaning wand securely with both hands before starting. Failure to do this could result in injury from a whipping wand. 13.Never make adjustments on machine while in operation. 14. Be certain all quick coupler fittings are secured before using pressure washer. WARNING: High pressure developed by these machines will cause personal injury or equipment damage. Keep clear of nozzle. Use caution when operating. Do not direct discharge stream at people, or severe injury or death will result. WARNING: Protect machine from freezing. WARNING Protect from freezing 12. To reduce the risk of injury, close supervision is necessary when a machine is used near children. Do not allow children to operate the pressure washer. This machine must be attended during operation. WARNING WARNING manual. 15. To keep machine in best operating conditions, it is important you protect machine from freezing. Failure to protect machine from freezing could cause malfunction of the machine and result in death, serious bodily injury, and/or property damage. Follow storage instructions specified in this PRESSURE WASHER OPERATOR’S MANUAL Important Safety Information 16. Inlet water must be clean fresh water and no hotter then 90°F. WARNING WARNING: Risk of asphyxiation. Use this product only in a well ventilated area. 17. Avoid installing machines in small areas or near exhaust fans. Adequate oxrisk of ygen is needed for comasphyxiation: use bustion or dangerous carthis product only in a well bon monoxide will result. ventilated area. 18. Manufacturer will not be liable for any changes made to our standard machines or any components not purchased from us. 19. The best insurance against an accident is precaution and knowledge of the machine. WARNING WARNING: Be extremely careful when using a ladder, scaffolding or any other relatively unstable location. The cleaning area should have adequate slopes and drainage to reduce the posRISK OF INJURY sibility of a fall due to slippery FROM FALLS WHEN surfaces. USING LADDER. 20. Do not overreach or stand on unstable support. Keep good footing and balance at all times. Shark HPB • 9.801-190.0 • Rev. 7/13 5 OPERATOR’S MANUAL PRESSURE WASHER Important Safety Information 21. Do not operate this machine when fatigued or under the influence of alcohol, prescription medications, or drugs. Follow the maintenance instructions specified in the manual. 6 Shark HPB • 9.801-190.0 • Rev. 7/13 CAUTION HOT WATER: Must use insulated spray gun and wand. Fuel Tank Downstream Detergent Injector Discharge Nipple Quick Coupler Burner Switch Pump Switch Wand Holder PRESSURE WASHER OPERATOR’S MANUAL Component Identification High Limit Thermostat Control Panel Pressure Switch Detergent Pick-Up Hose GFCI Pump Unloader High Pressure Nozzle Burner Chamber Fresh Water Faucet (not included) Garden Hose (not included) Burner Motor High Pressure Hose Detergent Bucket (not included) Nozzle Coupler Variable Pressure Insulated Wand Control Handle Insulated Spray Gun 98011900-2 7 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER Assembly Instructions Fuel Cap 98011900-4 98011900-3 STEP 1: Connect water supply hose. 98001190-5 STEP 4: Attach the high pressure hose to the spray gun using teflon tape on hose threads. STEP 2: Check fuel tank and pump oil levels. 98001190-7 STEP 5: Connect the high pressure hose to the pump discharge fitting. Push coupler collar forward until secure. 8 Shark HPB • 9.801-190.0 • Rev. 7/13 98011900-5 STEP 3: Connect high pressure hose to discharge nipple by sliding quick coupler collar back. Insert quick coupler onto discharge nipple and secure by pushing quick coupler collar forward. Place machine in a convenient location providing ample support, draining and room for maintenance. Electrical: This machine is intended for outdoor use. Machine must be stored indoors when not in use. This machine, when installed, must be electrically grounded in accordance to local codes. Check for proper power supply using a volt meter. Location: Placement: The location should protect the machine from damaging environmental conditions, such as wind, rain, and freezing. 1. This machine should be run on a level surface where it is not readily influenced by outside sources such as strong winds, freezing temperatures, rain, etc. It should be located to allow accessibility for refilling of fuel, adjustments and maintenance. Normal precautions should be taken by the operator of the machine to prevent moisture from reaching the electrical controls. 2. It is recommended that a partition be made between the wash area and the machine to prevent water spray from coming in contact with the machine. Excess moisture reaching any electric components or electrical controls will reduce machine life and may cause electrical shorts. 3. During installation of the machine, beware of poorly ventilated locations or areas where exhaust fans may cause an insufficient supply of oxygen. Sufficient combustion can only be obtained when there is a sufficient supply of oxygen available for the amount of fuel being burned. If it is necessary to install a machine in a poorly ventilated area, outside fresh air may have to be piped to the burner and a fan installed to bring air into the machine. Avoid small locations or areas near exhaust fans. Do not locate near any combustible material. Keep all flammable material at least 20 feet away. Allow enough space for servicing the machine. Local code will require certain distances from floor and walls. (Two feet away from walls should be adequate.) Water Source: The water source for the pressure washer should be supplied by a minimum 5/8" I.D. garden hose with a city water pressure of not less than 30 PSI. If the water supply is inadequate, or if the garden hose is kinked, the attached pressure washer will run very rough and the burner will not fire. PRESSURE WASHER OPERATOR’S MANUAL Installation Connection: Connect the wand, nozzle, hose and spray gun (where applicable). On pipe thread connections, use teflon tape to avoid water leaks. (See Component Identification). Venting: Adding exhaust vent pipe to your oil fired burner is not recommended because restricted air flow causes carbon build-up, which affects the operation, and increases maintenance on the coil. If a stack must be used, refrain from using 90° bends. If the pipe can not go straight up then use only 45° bends and go to the next size pipe. The overall pipe length must not exceed 6 feet in length*. *Note: After vent pipe installation test burner using a smoke tester and adjust air setting to achieve a #3 or below results. 9 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER operating instructions 98001190-8 STEP 1: Turn water on. 98001190-10 98001190-9 STEP 2: Connect the power cord into the proper electrical outlet, then push in the GFCI reset button. (Refer to serial plate for information). STEP 3: Grip spray gun handle securely and pull trigger. Then turn variable pressure control handle counterclockwise. Variable Pressure Wand (VP) Brass Soap Nozzle Trigger 98001190-11 STEP 4: Before installing nozzle, turn on water supply and run machine, allowing water to flush through the system until clear. High Pressure Nozzle Variable Pressure Control Handle 98001190-12 Selection of high or low pressure is accompanied by turning the handle. Note: High pressure nozzle must be inserted at end of wand to obtain high pressure. To apply soap read operator's manual. Turn switch to pump position. When a steady stream of water flows from the spray gun and wand the machine is ready for cold water cleaning by turning the variable pressure control handle clockwise to raise the pressure. For hot water washing, turn the switch to the burner position. (The burner will light automatically when the trigger on the spray gun is pulled.) 10 Shark HPB • 9.801-190.0 • Rev. 7/13 WARNING: Some detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause property damage or severe injury. STEP 1: Connect detergent injector to discharge nipple on machine, Connect high pressure hose to injector with quick coupler (check to make sure locking coupler sleeves are in proper position before applying water pressure. WARNING Detergent Injector the pump protector engages and cools the pump by discharging the warm water onto the ground. This thermal device prevents internal damage to the pump. cleaning tips Pre-rinse cleaning surface with fresh water. Place detergent suction tube directly into cleaning solution and apply to surface at low pressure (for best results, limit your work area to sections approximately 6 feet square and always apply detergent from bottom to top). Allow detergent to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. If surface appears to be drying, simply wet down surface with fresh water. If needed, use brush to remove stubborn dirt. Rinse at high pressure from top to bottom in an even sweeping motion keeping the spray nozzle approximately 1 foot from cleaning surface. Use overlapping strokes as you clean and rinse any surface. For best surface cleaning action spray at a slight angle. PRESSURE WASHER OPERATOR’S MANUAL detergents & general operating techniques Recommendations: 9801190-13 98001190-14 High Pressure Hose STEP 2: Use detergent designed specifically for pressure washers. Household detergents could damage the pump. Prepare detergent solution as required by the manufacturer. Fill a container with pressure washer detergent. Place the filter end of detergent suction tube into the detergent container. STEP 3: Apply safety latch to spray gun trigger. Turn variable pressure control handle until discharge water exits both tubes. Secure black detergent nozzle into quick coupler if you have a single wand. NOTE: Detergent cannot be applied using Red, Yellow, Green or White nozzles. 98001190-15 STEP 4: With the engine running, pull trigger to operate machine. Liquid detergent is drawn into the machine and mixed with water. Apply detergent to work area. Do not allow detergent to dry on surface. thermal pump protection • Before cleaning any surface, an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results. • If painted surfaces are peeling or chipping, use extreme caution as pressure washer may remove the loose paint from the surface. • Keep the spray nozzle a safe distance from the surface you plan to clean. High pressure wash a small area, then check the surface for damage. If no damage is found, continue to pressure washing. CAUTION - Never use: • Bleach, chlorine and other corrosive chemicals • Liquids containing solvents (i.e., paint thinner, gasoline, oils) • Tri-sodium phosphate products • Ammonia products • Acid-based products These chemicals will harm the machine and will damage the surface being cleaned. rinsing It will take a few seconds for the detergent to clear. Apply safety latch to spray gun. Remove black soap nozzle from the quick coupler. Select and install the desired high pressure nozzle. NOTE: You can also stop detergent from flowing by simply removing detergent siphon tube from bottle. If you run the engine on your pressure washer for 3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach high temperatures. When the water reaches this temperature, Shark HPB • 9.801-190.0 • Rev. 7/13 11 OPERATOR’S MANUAL PRESSURE WASHER shutting down and clean-up 98011900-16 STEP 1: Remove detergent suction tube from container and insert into 1 gallon of fresh water. Turn variable pressure wand handle for low pressure or connect the black detergent nozzle. Pull trigger on spray gun and siphon water for one minute. 98001190-18 98001190-17 STEP 2: Turn burner switch off and continue spraying water, allowing the water to cool. After water has cooled to less than 100°F, turn the attached pressure washer off. STEP 3: Turn off water supply. 98001190-19 STEP 4: Turn garden hose water off. Open the spray gun to relieve remaining pressure. STORAGE CAUTION: Always store your pressure washer in a location where the temperature will not fall below 32°F (0°C). The pump in this machine is susceptible to permanent damage if frozen. FREEZE DAMAGE IS NOT COVERED BY WARRANTY. 1. Stop the pressure washer, squeeze spray gun trigger to release pressure. 2. Detach water supply hose and high pressure hose. 3. Turn on the machine for a few seconds, until remaining water exits. Turn motor off immediately. 4. Drain the fuel from the fuel tank. 5. Do not allow high pressure hose to become kinked. 6. Store the machine and accessories in a room which does not reach freezing temperatures. When the pressure washer is not being operated or is being stored for more than one month, follow these instructions: 1. Replenish pump oil to upper level. 2. Drain fuel from fuel tank, fuel line and filter. 3. Cover the pressure washer and store in a clean, dry place that is well ventilated away from open flame or sparks. After Extended Storage CAUTION: Prior to restarting, thaw out any possible ice from pressure washer hoses, spray gun or wand. CAUTION: Failure to follow the above directions will result in damage to your pressure washer. 12 Shark HPB • 9.801-190.0 • Rev. 7/13 PROBLEM POSSIBLE CAUSE SOLUTION LOW OPERATING PRESSURE Faulty pressure gauge Install new gauge. Insufficient water supply Use larger garden hose; clean filter washer at water inlet. Old, worn or incorrect spray nozzle Match nozzle number to machine and/or replace with new nozzle. Plumbing or hose leak Check plumbing system for leaks. Retape leaks with teflon tape. Faulty or mis-adjusted unloader valve (where applicable) Adjust unloader for proper pressure. Install repair kit when needed. Worn packing in pump Install new packing kit. Fouled or dirty inlet or discharge valves in pump Clean inlet or discharge valves. Worn inlet or discharge valves Replace with valve kit. Air leak Tighten all clamps. Check detergent lines for holes. Valve in the injector head may be blocked, dirty or damaged Clean or replace valve in injector. Filler screen on detergent suction hose plugged Clean or replace. Dried up detergent plugging metering valve Disassemble and clean thoroughly. High viscosity of detergent Dilute detergent to specifications. Hole in detergent line(s) Repair hole. Low detergent level Add detergent if needed. Discharge water temperature above 180°F Lower discharge water temperature. DETERGENT NOT DRAWING PUMP RUNNING Pump sucking air NORMALLY BUT PRESSURE LOW Valves sticking ON INSTALLATION Unloader valve seat faulty FLUCTUATING PRESSURE PUMP NOISY PRESSURE WASHER Troubleshooting Guide Troubleshooting Check water supply and possibility of air seepage. Check and clean or replace if necessary. Check and replace if necessary. Nozzle incorrectly sized Check and replace if necessary (See serial plate for proper size). Worn piston packing Check and replace in necessary. Valves worn Check and replace if necessary. Blockage in valve Check and replace if necessary. Pump sucking air Check water supply and air seepage at joints in suction line. Worn piston packing Check and replace if necessary. Air in suction line Check water supply and connections on suction line. Broken or weak inlet or discharge valve springs Check and replace if necessary. Excessive matter in valves Check and clean if necessary. Worn bearings Check and replace if necessary. 13 Shark HPB • 9.801-190.0 • Rev. 7/13 Troubleshooting Guide PRESSURE WASHER Troubleshooting PROBLEM POSSIBLE CAUSE SOLUTION LOW WATER TEMPERATURE Improper fuel or water in fuel Drain fuel tank and replace with proper fuel. Low fuel pressure Increase fuel pressure. Weak fuel pump Check fuel pump temperature. Replace pump if needed. Fuel filter partially clogged Replace as needed. Soot build up on coils Clean coils with soot remover. Lime build up on coils Clean inside of coils using coil cleaner. Improper burner nozzle See Burner Specifications. Incoming water to machine warm or hot Lower incoming water temperature. Fuel pump pressure too high Lower fuel pressure. Fuel pump defective Replace fuel pump. Detergent line sucking air Tighten all clamps. Check detergent line for holes. Defective high limit switch (thermostat) Replace. Incorrect fuel nozzle size See Burner Specifications. Insufficient water supplied Check GPM to machine. Restricted water flow Check nozzle for obstruction, proper size. WATER TEMPERATURE TOO HOT 14 Shark HPB • 9.801-190.0 • Rev. 7/13 This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your Pressure Washers dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer. Perform maintenance more often under severe conditions. MAINTENANCE SCHEDULE Replace Fuel Lines Pump Oil Annually Inspect Daily inspect the oil level Change After first 50 hours, then every 500 hours or annually Clean Burner Filter Monthly (More often if fuel quality is poor) Remove Burner Soot Annually Burner Adjustment/Cleaning Annually De-scale Coil Annually (More often if required) Replace High Pressure Nozzle Every 6 months Replace Quick Connects Annually Clean Water Screen/Filter Weekly Clean Float/Supply Tank Every 6 months Replace HP Hose Annually if there is any sign of wear Grease Motor Every 10,000 hours Replace Burner Nozzle Annually PRESSURE WASHER Troubleshooting Guide Maintenance Charts Oil Change Record Date Oil Changed Month/Day/Year Estimated Operating Hours Since Last Oil Change Date Oil Changed Month/Day/Year Estimated Operating Hours Since Last Oil Change 15 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER Preventative Maintenance 1. Use clean fuel — kerosene, No. 1 home heating fuel or diesel fuel. Clean or replace fuel filter every 100 hours of operation. Avoid water contaminated fuel as it will seize up the fuel pump. De-soot coils monthly. Use an additive if diesel is being used. 2. Check to see that the attached pressure washer water pump is properly lubricated. 3. Follow winterizing instructions to prevent freeze damage to pump and coils. 4. Always neutralize and flush detergent from system after use. 5. If water is known to be high in mineral content, use a water softener on your water system, or de-scale as needed. 6. Do not allow acidic, caustic or abrasive fluids to be pumped through the system. 7. Always use high grade quality cleaning products. 8. Never run attached pressure washer pump dry for extended periods of time. 9. If machine is operated with smoky or eye burning exhaust, coils will soot up, preventing water from reaching maximum operating temperature. (See section on Maintenance and Service). 10. Never allow water to be sprayed on or near the motor or burner assembly or any electrical component. 11. Delime coils as per instructions. It is advisable, periodically, to visually inspect the burner. Check air inlet to make sure it is not clogged or blocked. Wipe off any oil spills and keep equipment clean and dry. The areas around the pressure washer should be kept clean and free of combustible materials, gasoline and other flammable vapors and liquids. The flow of ventilating air to the burner must not be blocked or obstructed in any manner. MAINTENANCE AND SERVICE Unloader Valves: Unloader valves trap pressure in the line when a shutoff spray gun is closed. Machines with unloader valves are preset and tested at the factory before shipping. Tampering with the factory settings may cause personal injury and/or property damage and will void the manufacturer's warranty. Winterizing Procedure: Damage due to freezing is not covered by warranty. Adhere to the following cold weather procedures whenever the washer must be stored or operated outdoors under freezing conditions. 16 During winter months, when temperatures drop below 32°F, protecting your machine against freezing is nec- essary. Store the machine in a heated room. If this is not possible then mix a 50/50 solution of anti-freeze/ water or windshield washer fluid with water in a 5 gallon bucket. Place a short section of garden hose into the bucket and connect it to the machine. Elevate the bucket and turn the pump on to siphon the anti-freeze through the machine. If compressed air is available, an air fitting can be screwed into the inlet connector and by injecting compressed air, all water will be blown out of the system. If you have an optional float tank, pour the antifreeze into this tank and run machine until antifreeze exits discharge nipple. High Limit Hot Water Thermostat: For safety, each machine is equipped with a high limit control switch. In the event the temperature of the water should exceed its operating temperature, the high limit control will turn the burner off until the water cools. Pumps: Use only SAE 30 weight non-detergent oil. Change oil after first 50 hours of use. Thereafter, change oil every three months or at 500 hour intervals. Oil level should be checked by using the dipstick found on the top of the pump or by the red dot visible through the oil gauge window. Oil should be maintained at that level. Cleaning of Coils: In alkaline water areas, lime deposits can accumulate rapidly inside the coil pipes. This growth is increased by the extreme heat build up in the coil. The best prevention for liming conditions is to use high quality cleaning detergents. In areas where alkaline water is an extreme problem, periodic use of deliming powder will remove lime and other deposits before coil becomes plugged. Deliming Coils With A Pressure Washer: Periodic flushing of coils is recommended. Step 1 Fill a 5 gallon bucket with 4 gallons of water, then add 1 lb. of deliming powder. Mix thoroughly. Step 2 Remove the high pressure nozzle from the pressure wand and put the wand into the bucket. Secure the trigger on the spray gun into the open position. Step 3 Attach a short section (3-5 ft.) of garden hose to the attached pressure washer to siphon solution from the elevated bucket. Start up pressure washer, allowing solution to be pumped through pressure washer and into HPB coils and back into the bucket. Solution should be allowed to circulate 2-4 hours. Shark HPB • 9.801-190.0 • Rev. 7/13 Step 4 After circulating solution flush entire system with fresh water. Electrode Setting (See illustration below) Removal of Soot In Heating Coil: In the heating process, fuel residue in the form of soot deposits may develop between the heating coil pipe and block air flow which will affect burner combustion. When soot has been detected on visual observation, the soot on the coil must be washed off after coil has been removed using the following steps: 1. Remove the tank head assembly by unscrewing the three tek screws and lifting the tank head off. 2. Remove the two pipe nipples and associated fittings. 3. Lift the coil out of the outer wrap. Caution: The coil weighs about 80 lbs. Use proper lifting techniques. 4. Clean, repair and replace the coil by reversing the above steps. Coil Reinstallation Reinstall by reversing the above steps 4 through 1. Rupture Disk If pressure from pump or thermal expansion should exceed safe limits, the rupture disk will burst, allowing high pressure to be discharged through hose to ground. When the disk ruptures, it will need to be replaced. Fuel: Use clean fuel oil that is not contaminated with water and debris. Replace fuel filter and drain tank every 100 hours of operation. Use Kerosene No. 1 or No. 2 Heating Fuel (ASTM D306) or diesel only. NEVER use gasoline in your burner tank. Gasoline is more combustible than fuel oil and could result in a serious explosion. NEVER use crankcase or waste oil in your burner. Fuel unit malfunction could result from contamination. Ignition Circuit: 5/32" Gap Electrode 5/16" 98011900-22 Top View Nozzles 1/16" Side View Electrodes Check: Periodically check wiring connections. If necessary to adjust electrodes, use diagram. Burner Nozzle: PRESSURE WASHER OPERATOR’S MANUAL Maintenance Keep the tip free of surface deposits by wiping it with a clean, solvent-saturated cloth, being careful not to plug or enlarge the nozzle. For maximum efficiency, replace the nozzle each season. Fuel Control System: This machine utilizes a fuel solenoid valve located on the fuel pump to control the flow of fuel to the combustion chamber. This solenoid is activated by a pressure switch located on the unloader valve. When an operator releases the trigger on the spray gun, the pressure drops, allowing the pressure switch to activate the fuel solenoid. The solenoid then closes, shutting off the supply of fuel to the combustion chamber. Controlling the flow of fuel in this way gives an instantaneous burn or no burn situation, thereby eliminating high and low water temperatures, and combustion smoke normally associated with machines incorporating a spray gun. Periodic inspection is recommended to insure that the fuel solenoid valve functions properly. This can be done by operating the machine and checking to see that when the trigger on the spray gun is in the off position, the burner is not firing. Periodically inspect wires, spring contact and electrodes for condition, security and proper spacing. For transformer test (CAUTION 10,000 VOLTS) use defect free insulated screwdriver and keep fingers off blade! Lay blade across one contact: OK if arc will span 1/2" between end of blade and other contact. 98011900-20 17 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER Maintenance Fuel Pressure Adjustment: FUEL AIR ADJUSTMENT: KNA To adjust fuel pressure, turn the adjusting screw with a standard screwdriver (located on the fuel pump) clockwise to increase, counterclockwise to decrease. Air Band Air Adjustment The oil burner on this machine is preset for operation at altitudes below 1000 ft. If operated at higher altitudes, it may be necessary to adjust the air band setting. Adjust air band for a #1 or #2 smoke spot on the Bacharach scale. If a smoky or eye-burning exhaust is being emitted from the stack, two things should be checked. Pressure Gauge Port First, check the fuel to be certain that kerosene or No. 1 home heating fuel is being used. Next, check the air adjustment on the burner. An oily, black, smoky fire indicates a lack of air and the air band should be moved to allow the air to flow through the burner. Sharp, eye-burning white fumes indicate too much air flowing through the combustion chamber. The air band should be moved to allow less air to flow through the burner. To adjust: start machine and turn burner ON. Loosen the two locking screws found on the air band openings (refer to illustrations) and close air band until black smoke appears from burner exhaust vent. Note air band position. Next, slowly open the air band until white smoke just starts to appear. Turn air band halfway back to the black smoke position previously noted. Tighten locking screws. 98011900-23 Fuel Pump Pressure Adjustment Screw FUEL AIR ADJUSTMENT: BECKETT Air Band Transformer 98011900-24 Air Band Adjustment Screw Fuel Pump Pressure Gauge Port Pressure Adjustment Screw 18 Shark HPB • 9.801-190.0 • Rev. 7/13 19 2 1 50 67 68 71 33 60 21 83 72 6 79 75 73 42 9 50 28 31 71 86, 69 For Detail See Control Panel Illus. 54 14 64 63 57 75, 26 5 88 27, 41, 71 53 4 16 10 30 49 30 3 51 78 49 18, 29, 84, 87 75 32 61 56 8 58 55 15 71 25 62 For Detail See Pump Illus. 26 37 48 11 23 66 PRESSURE WASHER OPERATOR’S MANUAL Exploded View For Detail See Steam Valve Options Illus. 65 22 70 24 36 13 7 45 47 For Detail See Optional Float Tank Illus. 69 39 17 34 44 52 77 48 To Fuel Tank 40 69 43 35 38 12 20 85 76 81 77 74 46 16 el Fu Toilter F 59 80 51 9801190-25 82 19 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER Exploded View Parts List ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION 1 8.932-960.0 Label, Diesel 1 35 9.802-171.0 2 9.800-006.0 Label, "Hot/Caliente" with Arrows Warning Nipple, 3/8" x 3/8" NPT Street Male 1 QTY 1 36 9.149-003.0 Manifold Coil Discharge 1 3 8.932-969.0 Label, Warning, Service Cord 37 9.802-043.0 1 Elbow, 1/2" JIC x 1/2" Female 1 4 9.800-021.0 Label, Hot Water Outlet 1 38 8.918-423.0 Hose, 3/8" x 22" 1 5 8.900-870.0 Label, Shark 1 39 8.706-958.0 6 9.800-035.0 Label, Warning (Lexan) 1 Hose Barb, 1/4" Barb, 1/4" Pipe, 90° 1 9.802-273.0 Wheel, 5" Caster, w/Brake 1 9.802-789.0 Nut, 3/8" Hex 2 42 8.719-935.0 Retainer Ring, Insulation 1 43 9.196-012.0 Screw, 10-24 x 1/4" 1 30" 7 9.802-272.0 Wheel, 5" Caster 1 40 8 9.802-070.0 Grip, 1" Square, Handle 2 41 9 8.706-612.0 Tank, Fuel, 9 Gallon Poly, Black 1 Cap, Fuel Tank, Plastic H60-AV 44 8.711-785.0 Hose, 3/8" Push-On 1 45 8.725-306.0 Filter, Fuel/H2O 10 9.802-089.0 1 11 9.800-020.0 Label, Cold Water Inlet 1 46 9.802-781.0 Nut, 3/8" Flange, Whiz Loc 4 12 9.803-062.0 Frame Assy 1 47 9.803-264.0 Nipple, 1/4" x 3", Black Pipe 1 13 9.802-225.0 Downstream Injector Assembly, Non Adj. #3 1 48 9.802-810.0 Washer, 5/8" Flat 2 Power Platform (109.0) Power Platform 49 9.802-770.0 Screw, 1/4" x 1" 7 1 1 50 9.802-094.0 Belt Guard 1 51 9.802-782.0 Collar, 5/8" 2 52 9.803-066.0 Axle, SR 1 53 9.803-131.0 Pump Rail, Black 1 54 For Pulley, Please See Specifications Pages. 55 For Pulley, Please See Specifications Pages. 56 For Belt, Please See Specifications Pages. 57 For Bushing, Please See Specifications Pages. 58 9.802-402.0 59 For Burner, Please See Specifications Pages. 60 9.802-825.0 Clip, Retainer 4 61 9.800-046.0 Label, Belt Guard 1 62 9.803-030.0 Retainer, Burner Insulation 1 9.802-768.0 Screw, 3/8" x 1-1/4" Whiz Loc 4 14 9.803-064.0 9.803-063.0 15 9.802-107.0 Fastener, Ratchet, Black Nylon 2 16 8.711-907.0 Wheel & Tire, 6.5" Steel Rim 12.5" Tire 2 17 8.750-094.0 Thermostat, 302° 1 18 For Motor, Please See Specifications Pages. 19 9.802-872.0 Tab, Belt Guard Mount 3 20 8.902-433.0 Valve, Safety Relief 1 21 8.932-965.0 Label, Warning, Exposed Pulley 1 4 Bushing, 24mm 1 22 9.802-792.0 Nut, Cage, 3/8" x 12 Gauge 23 9.802-905.0 Insulation Blanket, 18" OD x 4.5" ID 1 63 Nipple, 1/2" x 2-1/2" 1 64 9.802-014.0 Nipple, 1/2" x 3", Galvanized 1 8.718-618.0 Bolt, 5/16" x 3/4" 1 4 24 9.802-013.0 25 9.802-775.0 Nut, 1/4", Flange 4 65 26 9.802-720.0 Bolt, 3/8" x 1" (109.0,) 6 8 66 8.718-980.0 Washer, 5/16 Flat 67 9.802-794.0 Nut, Cage, 1/4" x 12 Gauge 6 27 9.802-733.0 Bolt, 3/8" x 3-1/2", Tap 2 68 9.802-754.0 Screw, 1/4" x 1/2", Whiz Loc 3 28 9.802-995.0 Coil, 18" 1 69 9.802-752.0 9.802-897.0 Insulation Blanket 1 Screw, 1/4" x 1-1/4", Whiz Loc 8 70 8.718-817.0 Nut, 1/4-20 Whiz Loc 8 71 9.802-807.0 Washer, 3/8", Flat (109.0) 29 9.802-518.0 9.803-279.0 Strain Relief, 3/4" (109.0) Strain Relief, 1" (110.0,111.0,112.0) 1 1 30 9.802-803.0 Washer, 1/4" 4 31 8.933-031.0 Outer Wrap, 18" Coil S.S. 1 72 25 23 9.802-430.0 GFCI, 230V, 30 Amp (109.0) 1 GFCI, 240V, 40 Amp (110.0) 1 15 ft. 32 9.802-973.0 Tank End 18" 1 9.802-434.0 33 8.717-442.0 Insulation Disk 1 9.802-437.0 Service Cord, 10/4 (111.0 ) 34 8.706-248.0 Plug, 3/8" 1 9.802-429.0 Service Cord, 12/4 (112.0 ) 15 ft. 20 Shark HPB • 9.801-190.0 • Rev. 7/13 ITEM PART NO. DESCRIPTION 73 8.920-445.0 Adapter Plate, Pump 74 8.706-941.0 Hose Barb, 1/4" 1 75 9.802-779.0 Nut, 3/8" ESNA 11 76 9.802-254.0 Fuel Line, 1/4" 28" 77 6.390-126.0 Clamp, Hose, .46-, .54 4 78 9.802-775.0 Nut 1/4" Flange ZN 2 79 9.804-082.0 Washer, 1/4" Flat Zinc 80 9.802-254.0 Fuel Line, 1/4" 81 9.802-448.0 Conduit, Water Tite 82 9.802-517.0 Connector 1/2" L/T 90° Black 1 83 9.802-765.0 Screw, 1/4-20 x 1/2" BH Black 2 84 9.802-436.0 9.802-437.0 9.802-425.0 Cord Service 10-3 (109.0) 41" Cord Service 10-4 (111.0) 41" Cord Service 8-3 (110.0) 41" 85 8.706-141.0 Coupling, 1/2" x Steel Pipe 1 86 9.802-793.0 Nut, Cage 1/4" x 16 Gauge 4 87 9.802-526.0 9.803-280.0 Lock Nut 3/4" (109.0) Lock Nut 1" (110.0, 111.0,112.0) 1 Nut, Whiz 5/16 Flange 4 88 9.802-778.0 QTY 1 2 28" 2.25 ft. PRESSURE WASHER OPERATOR’S MANUAL Exploded View Parts List 1 Not Shown 21 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER Control Panel exploded view 13 34 32 17 16 14 0 12 2 10 8 4 6 2 1 35, 36 2, 8 27 25 21 24 1 15 7 33 16 17 19 32 38 GR 39 OU ND 30 16 14 17 9 31 20 37 17 22 13 23 18 17 28 12 26 6 4 11 3 10 13 5 Control Panel Parts List ITEM PART NO. DESCRIPTION 1 9.802-451.0 Switch, Rocker, Carling w/Green Lens (Time Delay Option) 2 1 Rocker Switch, Red Lens (Time Delay Option) 1 9.802-452.0 QTY PART NO. Thermostat, 302° 1 9 9.802-283.0 Hour Meter (Optional) 1 10 8.712-357.0 Nozzle, SAQCMEG 0055, Red (109.0) Nozzle, SAQCMEG 1505.5, Yellow (109.0) Nozzle, SAQCMEG 2505.5, Green (109.0) Nozzle, SAQCMEG 4005.5, White (109.0) 8.712-358.0 9.802-447.0 For Fuse, Please See Specifications Pages. 8.712-359.0 4 For Fuse, Please See Specifications Pages. 5 For Transformer, Please See Specifications Pages. 8.712-360.0 7 9.802-518.0 9.802-521.0 48" 8.712-345.0 8.712-346.0 Strain Relief, Straight, L/T Strain Relief, 3/4" Watertight (110.0) 1 1 QTY 8.750-095.0 3 For Contactor, Please see specifications pages. DESCRIPTION 8 2 6 Conduit, 1/4" Split ITEM 8.712-347.0 8.712-348.0 22 Shark HPB • 9.801-190.0 • Rev. 7/13 Nozzle, SAQCMEG 0004, Red (110.0,111.0,112.0) Nozzle SAQCMEG 1504, Yellow (110.0,111.0,112.0) Nozzle, SAQCMEG 2504, Green (110.0,111.0,112.0) Nozzle, SAQCMEG 4004, White (110.0,111.0,112.0) 1 1 1 1 1 1 1 1 ITEM PART NO. DESCRIPTION 11 9.802-064.0 Grommet, Rubber, Nozzle Holder QTY 4 ITEM PART NO. DESCRIPTION 34 8.751-306.0 Timer, Multi Function 24V-120/240V (Time Delay Option) QTY 1 35 9.802-467.0 Base Relay (Time Delay Option) 1 Relay 120V (TimeDelay Option) 1 12 9.802-880.0 Cover, Electrical Box 1 13 9.802-759.0 Screw, 10/32" x 1/2" (Time Delay Option) 13 2 14 9.800-016.0 Label, Disconnect Power Supply 1 Nut, Cage, 10/32" x 16 Gauge 37 8.750-096.0 Knob, Themostat 302°F 1 6 38 8.712-190.0 Bezel, Plastic 1 39 9.196.012.0 Screw, 10/24 x 1/4" Hex 2 15 9.802-791.0 36 16 9.802-762.0 Screw, 10/32" x 1-1/4" (Auto Start/Stop Option) 1 1 17 9.802-695.0 Nut, 10/32" Keps (Auto Start/Stop Delay Option) (Time Delay Option) 4 1 2 18 9.800-112.0 Label, Control Panel 1 19 9.800-040.0 Label, Ground 1 20 9.802-517.0 Connector, 1/2", L/T 90°, Black 1 Strain Relief, Straight, L/T, Small 1 1 21 9.802-514.0 22 9.802-526.0 Locknut, 3/4" 23 9.802-525.0 Locknut, 1/2" 1 24 9.802-103.0 Bushing, Snap, 5/8" 1 25 9.802-518.0 Strain Relief, Straight, L/T, Large 1 26 9.800-018.0 Label, Tipover Hazard 1 27 9.800-049.0 Label, Cleaning Solution 1 28 9.802-526.0 Lock Nut 3/4" (All Models) 1 29 9.802-457.0 Din Rail (Time Delay Option) 4" 2" 30 9.802-491.0 Block Terminal 4 Pole (Auto Start/Stop, Time Delay Option) 1 31 9.802-472.0 Timer Solid State 120V, 5-60, Minute Adj. (Auto Start/Stop Option) 1 32 9.802-749.0 Screw 8/32" x 3/4" (Auto Start/Stop, Time Delay Option) 2 33 9.802-785.0 Nut 8/32" Keps (Auto Start/Stop, Time Delay Option) 2 9.802-468.0 Not Shown PRESSURE WASHER OPERATOR’S MANUAL Control Panel Parts List 23 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER Float Tank Option exploded view 21 30 38 16 31 32 34 33 15 14 4 21 35 30 17 39 39 18 42 36 Steam Option 29 28 4 11 10 13 12 18 7 20 21 9 41 24 19 7 27 40 22 1, 8 26 25 23 6 4 51 13 49 5 34 18 45 98011900-27 7 19 20 9 22 7 To Float Tank Auto Start/Stop Option QTY 8.706-645.0 Tank, Float 1 2 9.803-269.0 Shelf, Float Tank, Black 1 9 3 9.802-767.0 Screw, 3/8" x 3/4" HH NC, Whiz Loc 4 Elbow, 1/2" JIC x 3/8" Female, 90° 1 Screw, 5/16" x 1/2" Whiz Loc 4 6 9.802-259.0 Hose, 1/2", Push-On 7 9.802-201.0 Clamp, Screw, #6 3 8 8.932-994.0 Valve, Float 1 18 45 37 7 43 10 9 27 7 To Float Tank 23 1 9.803-277.0 50 54 DESCRIPTION 5 53 46 PART NO. 9.802-039.0 38 32 33 21 21 11 10 44 27 21 47 47 ITEM 4 24 43 46 23 48 53 20 19 49 31 33 50 21 39 35 3 13 47 47 22 2 50 48 36 4 ITEM Auto Start/Stop Steam Option PART NO. DESCRIPTION 9.802-062.0 Ball Float 1 8.706-943.0 Hose Barb, 5/8" Barb x 1/2" ML Pipe 1 10 8.706-820.0 Elbow, 1/2" Female, Brass 1 11 9.802-111.0 Nipple, 1/2" NPT, 5/16", Modified Close 1 12 9.802-043.0 Elbow, 1/2" x 1/2" Female, 90° 1 13 8.918-423.0 Hose, 3/8" x 22", 2 Wire, Pressure Loop 1 14 9.802-146.0 Swivel, 1/2" MP x 3/4" GHF w/Strainer 1 20" Shark HPB • 9.801-190.0 • Rev. 7/13 QTY ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION 15 9.802-961.0 Hose Connection Bracket 1 46 9.802-128.0 Nipple, 1/2" JIC x 1/2" Pipe QTY 1 16 9.802-700.0 Bolt, 1/4" x 3/4", NC HH 2 47 9.802-151.0 17 9.802-781.0 Nut, 3/8", Flange, Whiz Loc, NC Swivel, 1/2" JIC Female, Push-On 2 4 48 9.802-259.0 Hose, 1/2", Push-On 16" 18 8.706-780.0 Nipple, 1/4" Hex 1 49 9.802-129.0 Elbow, 1/2" JIC x 3/8" 90° 1 19 8.707-317.0 Valve, Flow Control 1 50 9.802-362.0 Unloader VB8 w/Switch 1 20 8.706-941.0 Hose Barb, 1/4" Barb x 1/4" ML Pipe 51 9.802-458.0 1 Switch, Pressure N/O 1/4", NPT SS 1 1 3 21 6.390-126.0 Clamp, Hose, .46-, .54 ST (Float Tank w/Steam) 22 9.802-251.0 Tube, 1/4" x 1/2", Clear Vinyl 72" 23 8.707-058.0 Strainer, 1/4" Brass w/Check Valve 1 24 9.802-087.0 Cover, Float Tank, Portotenica 1 25 9.802-131.0 Elbow, 1/2" JIC x 1/2", 90° 1 26 9.802-151.0 Swivel, 1/2" JIC Female, Push-On 27 9.802-260.0 Hose, 5/8" Push-On 12" 28 9.802-773.0 Nut, 1/4", ESNA, NC 2 29 9.802-802.0 Washer, 1/4" Flat, SAE 4 30 8.706-958.0 Hose Barb, 1/4" Barb x 1/4" Pipe, 90° 1 31 9.802-187.0 Valve, Flow Control w/Metering 1 1 52 8.706-207.0 Elbow, 3/8" Street 1 53 8.706-309.0 Adapter, 3/8" x 3/8" Street 1 54 8.706-940.0 Hose Barb, 1/4" Barb x 1/8" ML Pipe 1 Not Shown PRESSURE WASHER OPERATOR’S MANUAL Float tank Parts List 1 32 8.705-973.0 Nipple, 1/4" Hex Steel 33 9.802-632.0 Cap, Valve w/ 1/4" Gauge Port 34 9.802-254.0 Hose, 1/4", Push-on 14" 35 8.933-006.0 Switch, MV60 Flow 1 36 8.706-168.0 Elbow, 3/8" Male Pipe 1 37 9.804-555.0 Cross, 1/2" Female w/ 1/4"-20 Hole 1 38 9.800-026.0 Label, Open For Steam 1 39 8.706-997.0 Adapter 1/4" x 1/8" 1 40 9.804-554.0 Screw, 10/32" x 2-1/2" 1 41 9.802-695.0 Nut, 10/32" Keps 1 42 8.706-855.0 Tee, 1/4" Street 1 43 8.706-797.0 Nipple, 1/2" Hex 1 44 9.802-119.0 Cross, 1/2" Female 1 45 8.706-915.0 Bushing, 1/2" x 1/4" 1 1 25 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER auto start/stop options exploded view 7 8 13 16 6 9 15 12 5 98011900-28 11 5 14 10 3 4 2 1 auto start/stop options parts list ITEM PART NO. DESCRIPTION 1 9.802-146.0 Swivel, 1/2" MP x 3/4" GHF w/Strainer QTY 1 2 8.706-844.0 Tee, 1/2" Female Pipe 1 3 8.706-797.0 Nipple, 1/2" Hex 1 4 9.802-127.0 Nipple, 1/2" JIC x 1/2" MPT Pipe 1 5 9.802-151.0 Swivel, 1/2" JIC Fem, Push-on 6 9.802-259.0 Hose, 1/2" Push-on 16" 7 9.802-039.0 Elbow, 1/2" JIC, 3/8" 1 8 9.802-129.0 Elbow, 1/2" JIC x 3/8" 1 9 9.802-362.0 Unloader, VB8 w/Switch 1 10 Pump, Please See Specifications Pages 11 8.707-256.0 Pump Protector, 1/2" ITEM PART NO. DESCRIPTION QTY 12 9.802-632.0 Cap, Valve with 1/4" Ga Port 1 13 9.802-458.0 Switch, Pressure 1/4" NPT 1 14 8.706-207.0 Elbow, 3/8" Street 1 15 8.706-309.0 Adapter, 3/8" x 3/8" Street 1 16 8.918-423.0 Hose, 3/8" x 22", Pressure Loop 1 2 1 26 Shark HPB • 9.801-190.0 • Rev. 7/13 PRESSURE WASHER OPERATOR’S MANUAL auto start/stop - steam options Exploded view 10 12 21 11 22 8 1 20 EN OP R FO M EA ST 99011 10- 19 9 18 23 17 6 7 22 15 14 13 5 16 6 98011900-29 3 4 2 auto start/stop - steam options parts list ITEM PART NO. DESCRIPTION 1 8.918-423.0 Hose, 3/8" x 22" Pressure Loop 1 Swivel, 1/2 x 3/4 GHF w/Strainer 1 2 9.802-146.0 QTY 3 9.802-123.0 Tee, 1/2" w/1/8" Hole Street 1 4 9.802-131.0 Elbow, 1/2" JIC x 1/2 - 90° 1 5 9.802-142.0 Hose Barb, 1/4 Barb x 1/8" Pipe 90°1 6 9.802-151.0 Swivel, 1/2" JIC Fem, Push-on 2 7 9.802-259.0 Hose, 1/2" Push-on 16" 8 9.802-129.0 Elbow, 1/2 JIC x 3/8" 90° 1 9 9.802-362.0 Unloader, VB8 w/Switch 1 10 9.803-044.0 Elbow, 3/8" Male Pipe 1 11 9.802-459.0 Switch, Flow 1 12 9.802-039.0 Elbow, 1/2 JIC, 3/8" 1 13 8.706-207.0 Elbow, 3/8" Street 1 ITEM PART NO. DESCRIPTION 14 8.706-309.0 Adapter, 3/8" x 3/8" Steel QTY 1 15 8.707-256.0 Pump Protector 1/2" 1 16 For Pump, Please See Specifications Pages 17 9.804-022.0 Cap, Valve w/1/4" Ga. Port 1 18 9.802-010.0 Nipple, 1/4" Hex Steel 1 19 9.802-187.0 Valve, Flow Control w/Metering 1 20 9.802-026.0 Label, Open for Steam 1 21 9.802-143.0 Hose Barb, 1/4" Barb x 1/4" Pipe 1 22 6.390-126.0 Clamp, Hose 2 23 9.802-254.0 Hose, 1/4" Push-on 14" 27 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER Pump Assembly exploded view 2 7 1 6 98011900-30 3 8 5 4 Pump Assembly Parts List ITEM PART NO. DESCRIPTION QTY 1 8.707-256.0 Pump Protector, 1/2" 1 2 9.802-458.0 Pressure Switch, 1/4" 1 3 9.802-039.0 Elbow, 1/2" JIC x 3/8", 90° 1 4 9.802-146.0 Swivel, 1/2" GHF 1 5 For Unloader, Please See Specifications Pages 6 For Pump, Please See Specifications Pages 7 9.802-632.0 Cap, Valve w/1/4" Port 1 8 8.706-864.0 Plug, 1/8" Countersunk 1 28 Shark HPB • 9.801-190.0 • Rev. 7/13 PRESSURE WASHER OPERATOR’S MANUAL Steam Options exploded view 1 2 10 3 4 8 5 11 15 12 9 6 2 7 13 14 98011900-31 Steam Options Parts List ITEM PART NO. DESCRIPTION 1 9.802-143.0 Hose Barb, 1/4" Barb x 1/4" Pipe, 90° QTY ITEM PART NO. DESCRIPTION QTY 8 For Unloader, Please See Specifications Pages. 2 9 For Pump, Please See Specifications Pages. 10 9.800-026.0 Label, Open For Steam 11 9.802-254.0 Hose, 1/4" Push-On 12 9.802-039.0 Elbow, 1/2" JIC x 3/8" 1 13 9.803-044.0 Elbow, 3/8" Pipe, Male 1 14 9.802-142.0 Hose barb 1/4", Barb x 1/8" Pipe 90° 1 Pump Protector, 1/2" 2 2 6.390-126.0 Clamp, Hose, .46-, .54 ST 2 3 9.802-187.0 Valve, Flow Control w/Metering 1 4 9.802-010.0 Nipple, 1/4" Hex Steel 1 5 9.802-632.0 Cap, Valve with 1/4" Gauge Port 2 6 9.802-459.0 Switch, MV-60 Flow 1 7 9.802-146.0 Swivel, 1/2" MP x 3/4" GHF w/Strainer 1 15 8.707-256.0 1 14" 29 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER Hose & Spray Gun Assembly exploded view 6 8 9 10 3 2 1 5 7 Pressure Nozzle 4 98011900-32 Hose & Spray Gun Assembly Parts List ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION 1 9.802-165.0 Coupler, 1/4" Male 1 7 9.802-160.0 Strainer, 1/4" Hose Barb 1 9.802-096.0 Quick Coupler O-ring, Small 8 9.802-166.0 Coupler, 3/8" Female 1 1 9.802-100.0 Quick Coupler, O-Ring, Large 1 2 2 9.802-286.0 Nozzle Only, 1/8" Soap 1 3 9.802-222.0 Wand, Zinc, VP, w/Coupler 1 Hose, 3/8" x 50' 1 Wire, Tuff-Flex 1 Gun, ST-1500, 5000 PSI 10.4 GPM 1 Detergent Injector, Non Adjust #3 (109.0, 110.0, 111.0, 112.0) 1 4 5 6 8.739-125.0 8.710-384.0 9.802-225.0 9 6.390-126.0 Clamp, Hose, .46-, .54 ST 10 9.802-251.0 Tube, 1/4" x 1/2" Clear Vinyl 30 Shark HPB • 9.801-190.0 • Rev. 7/13 Not Shown QTY 6 ft. PRESSURE WASHER OPERATOR’S MANUAL UU1 UNLOADER VALVE EXPLODED VIEW 9.175-018.0, 3500 PSI Universal Unloader UU1 UNLOADER VALVE EXPLODED VIEW PARTS LIST ITEM Part # description 1 2 3 8.749-795.0 4 8.749-796.0 5 9.152-372.0 6 7 8 9 9.152-016.0 10 11 9.149-001.0 12 9.152-017.0 8.762-005.0 13 9.149-002.0 9.149-005.0 14 9.196-011.0 15 16 KIT qty Piston Housing A Piston C Piston O-Ring Back up Main Block Piston Ring Ball Seat C O-Ring, 10.5 ID x 1.5 CS A,C Plunger B Plunger Housing Bypass Spring C Low Pressure Port Sliding Connector, 30 mm Sliding Connector, 40 mm Sliding Connector H 1/2" Sliding Connector H 3/8" Plug, 5/8 - 18 UNF O-Ring 12 ID x 2 CS A O-Ring 6 ID x 2 CS A 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 ITEM Part # description KIT qty 17 9.149-006.0 18 19 20 21 22 23 8.762-001.0 8.762-011.0 8.762-000.0 24 8.762-000.0 25 9.802-893.0 26 9.803-921.0 9.802-893.0 27 28 8.706-865.0 Sliding Connector Guide O-Ring Back up A Conical Seal C O-Ring 6.75 x 1.78 BN80 A Spring Seat C Plunger Spring B Banjo Bolt, 1/2" Banjo Bolt, 1/2" - 1/4" NPT Banjo Bolt 3/8" Banjo Bolt 3/8" Seal Washer 3/8" Seal Washer, 1/2" (0120, 0130) Seal Washer 3/8" (0140) O-Ring 15 ID x 2 CS A,B Plug, 1/4" Kit A 9.104-038.0 KIT B 9.104-039.0 KIT C 9-104-040.0 O-Ring Repair Kit Outlet Kit Stem Repair Kit 1 1 1 1 1 1 1 1 1 1 2 2 2 3 1 31 Shark HPB • 9.801-190.0 • Rev. 7/13 OPERATOR’S MANUAL PRESSURE WASHER KM.3 Series Pump Exploded View 8.751-186.0 KM3540R.3 8.751-187.0 KM4030R.3 8.751-188.0KM4030L.3 8.751-189.0KM4035R.3 8.751-190.0KM4035L.3 8.751-191.0KM5030R.3 8.751-192.0KM5030L.3 TORQUE SPECS Item # Ft.-lbs 14 75 15 30 23 8 33 9 43 13 48 7.6 KM.3 Series Pump Exploded View parts List 32 item Part no. Description QTY item Part no. Description 1 8.751-216.0 Crankcase 1 23 9.802-944.0 Screw, Hex, 8mm x18mm QTY 8 2* See Kits Below Plunger Oil Seal 3 24 8.717-210.0 Closed Bearing Housing 1 3* See Kits Below O-Ring Ø1.78 x 31.47 3 25 9.803-192.0 O-Ring Ø1.78 x 60.05 2 4* See Kits Below Pressure Ring 3 26 8.933-011.0 Tapered Roller Bearing 2 5* See Kits Below U-Seal 3 27 8.751-222.0 Crankshaft (5030,3540) 1 6* See Kits Below Intermediate Ring 3 8.751-223.0 Crankshaft (4030, 4035) 1 7* See Kits Below U-Seal 3 28 9.803-167.0 Crankshaft Key 1 8 9.803-199.0 Washer, Copper 1 29 9.802-921.0 Oil Dip Stick 1 9 9.802-926.0 Plug, Brass 1/2 1 30 9.803-140.0 Crankshaft Seal 1 10 8.751-218.0 Manifold Head 1 31 9.803-178.0 Shim 2 11* See Kits Below O-Ring Ø2.62 x 17.13 6 32 8.717-209.0 Bearing Housing 1 12* See Kits Below Valve Assembly 6 33* See Kits Below Plunger Nut, M8 3 13* See Kits Below O-Ring Ø2.62 x 20.29 6 34* See Kits Below Copper Spacer 3 14 9.802-928.0 Valve Plug 6 35* See Kits Below Plunger (4035) 3 15 9.802-938.0 Manifold Stud Bolt 8 See Kits Below Plunger (4030, 5030) 3 See Kits Below Plunger (3540) 3 16 9.802-884.0 Washer 16 17 9.803-198.0 Copper Washer 3/8 1 18 9.802-925.0 Brass Plug 3/8 1 Shark HPB • 9.801-190.0 • Rev. 7/13 item Part no. Description QTY 36* See Kits Below Copper Spacer 3 37* See Kits Below O-Ring Ø1.78 x 7.66 3 38* See Kits Below Teflon Ring 3 39 8.751-224.0 Plunger Rod 3 40 9.803-158.0 Connecting Rod 3 41 8.751-228.0 Connecting Rod Pin 3 42 9.803-218.0 Spring Washer 6 43 9.803-238.0 Connecting Rod Screw 6 44 8.933-016.0 O-Ring, Ø2.62 x 126.67 1 45 8.751-229.0 Crankcase Cover 1 46 9.803-197.0 O-Ring, Ø1.78 x 14 1 47 9.803-202.0 Sight Glass 3/4 1 48 9.802-939.0 Cover Screw 5 PRESSURE WASHER OPERATOR’S MANUAL KM.3 Series Pump Exploded View parts List * Available in kit (See below) Repair kit nO. KIT DESCRIPTION item numbers included No. of cylinders kit will service Repair kit nO. KIT DESCRIPTION item numbers included No. of cylinders kit will service 8.725-360.0 8.725-362.0 8.725-358.0 Plunger Seal 4035 18mm Plunger Seal 4030 5030 20mm Complete Seal Plunger Seal Packing 3540 4035 15mm 18mm 3, 5, 7 3, 5, 7 3, 5, 7 3 3 8.751-237.0 Plunger 4035 18mm 33, 34, 35, 36, 37, 38 1 8.725-363.0 8.725-359.0 Complete Seal Packing 4030 5030 20mm Complete Seal Packing 3540 15mm 3, 4, 5, 6, 7 3, 4, 5, 6, 7 3, 4, 5, 6, 7 3 1 1 1 8.751-238.0 8.933-023.0 9.802-603.0 9.802-609.0 Plunger 4030 5030 20mm Plunger 3540 15mm Complete Valve Plunger Oil Seals 11, 12, 13 2 6 3 33, 34, 35, 36, 33, 34, 35, 36, 37, 38 37, 38 1 1 8.725-361.0 33 Shark HPB • 9.801-190.0 • Rev. 7/13 PRESSURE WASHER Specifications Specifications PUMP MOTOR Machine Pump Pump Unloader Unloader Part # Model Parts# Replacement Production Pulley Pulley Motor Part # Size Motor Voltage Part # Pulley Pulley Part # 1.109-109.0 KM-4035 8.751-189.0 9.175-018.0 9.175-016.0 2AK74H 9.802-374.0 6 HP 230v/1ph/60Hz 9.802-336.0 2AK54H 8.715-550.0 1.109-110.0 KM-4035 8.751-189.0 9.175-018.0 9.175-016.0 2BK80H 9.802-389.0 7.5 HP 230v/1ph/60Hz 8.715-097.0 2BK52H 9.802-386.0 1.109-111.0 KM-4035 8.751-189.0 9.175-018.0 9.175-016.0 2BK80H 9.802-389.0 7.5 HP 230v/3ph/60Hz 8.751-014.0 2BK50H 8.715-583.0 1.109-112.0 KM-4035 8.751-189.0 9.175-018.0 9.175-016.0 2BK80H 9.802-389.0 7.5 HP 460v/3ph/60Hz 8.751-014.0 2BK50H 8.715-583.0 34 Shark HPB • 9.801-190.0 • Rev. 7/13 CONTROLS MOTOR Model Bushing Belt Belt Motor Part # Bushing Part # Size Part # Contactor 109.0 Hx1-1/8" 9.802-400.0 AX 36(2) 9.802-408.0 110.0 Hx1-3/8" 9.802-401.0 BX 36(2) 9.802-416.0 111.0 Hx1-3/8" 9.802-401.0 BX 36(2) 112.0 Hx1-3/8" 9.802-401.0 BX 36(2) Stepdown Primary Second Overload Transformer Fuse Part# Fuse Part# 8.724-281.0 NA 9.802-551.0 9.802-461.0 9.802-463.0 8.724-281.0 8.724-306.0 9.802-551.0 8.933-007.0 9.802-463.0 9.802-416.0 8.724-272.0 8.724-305.0 9.802-551.0 9.802-461.0 9.802-463.0 9.802-416.0 8.724-268.0 8.724-312.0 9.802-550.0 9.802-460.0 9.802-465.0 PRESSURE WASHER Specifications Specifications 35 Shark HPB • 9.801-190.0 • Rev. 7/13 PRESSURE WASHER Specifications Beckett burner Specifications Burner Fuel Nozzle Model # Assy # 1.109-109.0 1.109-110.0 1.109-111.0 1.109-112.0 9.802-561.0 9.802-561.0 9.802-561.0 9.802-557.0 8.717-272.0 8.717-272.0 8.717-272.0 8.717-272.0 Igniter Motor 9.802-661.0 9.802-661.0 9.802-661.0 9.802-647.0 9.802-635.0 9.802-635.0 9.802-635.0 9.802-642.0 Burner Solenoid/Cord Fuel Pump/ Solenoid Coil 9.802-645.0 9.802-645.0 9.802-645.0 9.802-645.0 Fuel Electrode 9.802-640.0 9.802-640.0 9.802-640.0 9.802-640.0 9.802-670.0 9.802-670.0 9.802-670.0 9.802-670.0 Fuel Pump/ Solenoid Coil Fuel Electrode shark burner Specifications Model # Assy # 1.109-109.0 1.109-110.0 1.109-111.0 1.109-112.0 8.918-903.0 8.918-903.0 8.918-903.0 8.918-902.0 Burner Fuel Nozzle 8.717-272.0 8.717-272.0 8.717-272.0 8.717-272.0 Transformer 8.919-115.0 8.919-115.0 8.919-115.0 8.919-114.0 Motor Burner Solenoid/Cord 8.750-518.0 8.750-518.0 8.750-518.0 8.750-517.0 36 Shark HPB • 9.801-190.0 • Rev. 7/13 9.802-645.0 9.802-645.0 9.802-645.0 9.802-645.0 9.802-640.0 9.802-640.0 9.802-640.0 9.802-640.0 8.750-778.0 8.750-778.0 8.750-778.0 8.750-778.0 PRESSURE WASHER OPERATOR’S MANUAL KNA burner Replacement Parts For best performance specify genuine KNA replacement parts 37 Shark HPB • 9.801-190.0 • Rev. 7/13 Part # 8.919-050.0 8.751-160.0 8.700-758.0 8.700-759.0 8.700-760.0 8.753-000.0 8.750-762.0 8.750-763.0 8.750-764.0 8.750-765.0 8.750-783.0 8.750-541.0 8.750-517.0 8.750-518.0 8.751-074.0 8.750-543.0 8.751-073.0 8.750-520.0 8.751-072.0 8.750-547.0 8.750-545.0 8.749-000.0 8.752-034.0 8.752-035.0 8.750-539.0 8.750-526.0 8.750-525.0 Varies 8.750-778.0 8.751-342.0 8.750-779.0 8.750-782.0 8.750-780.0 8.750-781.0 8.919-114.0 8.919-115.0 8.919-116.0 8.751-165.0 Item # 1 2 3 3 3 3 4 4 4 5 5a 6 7 7 7 8 8 9 9 11 12 13 14 15 16 18 19 20 21 21 22 22 22 22 23 23 23 24 BURNER HOUSING ASSEMBLY AIR GUIDE FUEL PUMP, SUNTEC A2VA-3106 12-24V SOL FUEL PUMP, SUNTEC A2VA-3106 120V SOL FUEL PUMP, SUNTEC A2VA-3106 230V SOL FUEL PUMP, DANFOSS 071N1298 COIL, SOLENOID DANFOSS 230V COIL, SOLENOID DANFOSS 115V COIL, SOLENOID DANFOSS 12-24V CABLE, SOLENOID COIL, DANFOSS MOUNTING KIT, FLANGE/HUB, DANFOSS AIR BAND MOTOR, 1/6 HP 115V 60Hz MOTOR, 1/6 HP 230V 60Hz MOTOR, 1/7 HP 12VDC Ametek COUPLING, FLEX, 1/2" x 5/16" COUPLING, FLEX, 5/16" x 5/16" FAN, 4.53" X 2.42", 1/2" BORE, F115-62S FAN, 4.53" x 2.42" x .313 BORE, F115-625 CONNECTOR, 37 DEG FLARE X 1/8" NPT, LONG CONNECTOR, 37 DEG FLARE X 1/8" NPT FUEL LINE ASSEMBLY FLANGE, KNA BURNER, 1" TUBE FLANGE, KNA BURNER, 3" TUBE GASKET, FLANGE GUN, ELECTRODE / NOZZLE, 3" GUN, ELECTRODE / NOZZLE, 1" NOZZLE, FUEL ELECTRODE, IGNITION, AC ELECTRODE, IGNITION, DC CONE, AIR F4 CONE, AIR F6 CONE, AIR F12 CONE, AIR F22 IGNITOR, BURNER 120V IGNITOR, BURNER 230V IGNITOR, BURNER 12VDC PLUG, HOLE 0.875 PLASTIC Description 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Qty 25 26 27 28 29 30 30 30 30 31 32 33 34 35 36 37 38 39 40 42 43 44 46 46 46 46 46 46 48 49 50 51 52 53 53 53 54 Item # 8.750-830.0 8.751-134.0 8.918-454.0 8.750-542.0 8.750-116.0 8.750-817.0 8.750-818.0 8.750-819.0 8.750-820.0 8.750-784.0 8.750-785.0 8.733-001.0 8.718-762.0 8.752-137.0 8.718-810.0 8.750-770.0 8.750-816.0 8.750-768.0 8.750-771.0 — 9.801-268.0 — 9.807-339.0 9.807-340.0 9.807-341.0 9.807-342.0 9.807-343.0 9.807-344.0 9.801-274.0 8.919-105.0 8.716-451.0 9.802-510.0 9.807-348.0 9.807-345.0 9.807-346.0 9.807-347.0 8.751-354.0 Part # 1 1 1 1 1 2 1 1 1 1 1 2 2 1 6 3 1 4 4 1 1 1 1 4 1 1 1 1 1 1 1 2 1 1 1 1 1 Qty PRESSURE WASHER PLUG, HOLE 0.285 PLASTIC PLUG, 1/8" NPT x Hex Shoulder GASKET, JUNCTION BOX COVER, JUNCTION BOX BLOCK, TERMINAL, 5 POLE LIGHT, INDICATOR, GREEN 14V LIGHT, INDICATOR, GREEN 28V LIGHT, INDICATOR, GREEN 125V LIGHT, INDICATOR, GREEN 250V SITE GLASS RING, PUSH ON INTERNAL, 1305-112 SCREW, 8 x 1/4" HI LOW THREAD CUT, PPH SCREW, 8-32 X 1/2", M PH RDH PL Washer, Copper SCREW, 10/32 x 1/2", WHIZ LOC FLANGE SCREW, 10/32 x 5/8", WHIZ LOC FLANGE SCREW, 10/32 X 1/4" GROUNDING SCREW, 1/4-20 x 1", WHIZ LOC FLANGE SCREW, 1/4-20 X 1/2", PHIL FHMS LABEL, BRAND NAME LABEL, DISCONNECT POWER SUPPLY LABEL, SERIAL PLATE LABEL, WIRING DIAGRAM, BURNER 115V-115V LABEL, WIRING DIAGRAM, BURNER 230V-230V LABEL, WIRING DIAGRAM, BURNER 230V-115V LABEL, WIRING DIAGRAM, BURNER 115V-24V LABEL, WIRING DIAGRAM, BURNER 230V-24V LABEL, WIRING DIAGRAM, BURNER 12VDC LABEL, BURNER LIGHTS PLATE, TERMINAL BLOCK NUMBERS TERMINAL, JUMPER SPADE CABLE, TIE, 4" BLACK LABEL, CLEAR MYLAR LABEL, IGNITER 120V LABEL, IGNITER 230V LABEL, IGNITOR 12VDC gasket, burner tube Description OPERATOR’S MANUAL KNA burner Replacement Parts For best performance specify genuine KNA replacement parts 38 Shark HPB • 9.801-190.0 • Rev. 7/13 Phone: 800-771-1881 Fax: 877-526-3246 www.sharkpw.com WHAT THIS WARRANTY COVERS All Shark pressure washers are warranted by Shark to the original purchaser to be free from defects in materials and workmanship under normal use, for the periods specified below. This Limited Warranty, subject to the exclusions shown below, is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced under this warranty will assume the remainder of the pressure washer’s warranty period. FIVE YEAR PARTS AND ONE YEAR LABOR WARRANTY Components manufactured by Shark, such as frames, handles, float tanks, fuel tanks, belt guards, and heating coils. Pro-Duty rated units (DD Series) have a three-year limited warranty against defects and workmanship. Internal components on the oil-end of Kärcher axial pumps have a 5 year warranty. Kärcher crankshaft pumps have a 7 year warranty on non-wear parts. Heating coils are pro-rated at 25% after 2 years. Kärcher and non-Kärcher swash and wobble plate pumps have a one year warranty; other pumps carry their manufacturer’s warranty. ONE YEAR PARTS AND ONE YEAR LABOR WARRANTY All other components, excluding normal wear items as described below, will be warranted for one year on parts and labor. Parts and labor warranty on these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty. WARRANTY PROVIDED BY OTHER MANUFACTURERS Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manufacturers’ local authorized service centers. Shark is not authorized and has no responsibility to provide warranty service for such components. Motors manufactured outside of the United States will be warranted by Shark. WHAT THIS WARRANTY DOES NOT COVER This warranty does not cover the following items: 1. Normal wear items, such as nozzles, spray guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings, packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protectors. 2. Any components or other devices incorporated into a Shark product that are not manufactured by Shark, including, but not limited to gasoline engines, pumps, etc. 3. Defects caused by improper or negligent operation or installation, accident, abuse, misuse, neglect, unauthorized modifications, repair or maintenance of the product by persons other than authorized representatives of Shark, including, but not limited to, the failure of the Customer to comply with recommended product maintenance schedules. 4. Shark products that have been returned by the original Customer and are ultimately re-sold by an Authorized Servicing Dealer or other sales or service outlet to another purchaser. 5. Shark products that are sold by any distributor or retailer that is not an official authorized dealer or retailer of Shark products. 6. Defects caused by acts of nature and disaster including, but not limited to, floods, fires, wind, freezing, earthquakes, tornadoes, hurricanes and lightning strikes. 7. Defects caused by water sediments, rust corrosion, thermal expansion, scale deposits or a contaminated water supply (such as water in the unit with chloride content higher than that of 80 mg/liter or use of chemicals not approved or recommended by Shark). 8. Defects caused by improper voltage, voltage spikes or power transients in the electrical supply. 9. Devices or accessories not distributed or approved by Shark. 10. Any cost of labor arising from the removal and reinstallation of the alleged defective part by Customer. 11. Transportation of the product to an Authorized Servicing Dealer, field labor, replacement rental and any freight charges. Any components, accessories or other devices provided with the product but not manufactured by Shark (such as engines, pumps, etc.) are subject to warranties and service through their respective manufacturers authorized service centers and according to the applicable terms and conditions of such manufacturers warranties. Such components or other devices not manufactured by Shark should be referred by the Customer to an authorized service center or their respective manufacturers for repair or replacement. THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, WHETHER ARISING BY LAW, CUSTOM OR CONDUCT. SHARK MAKES NO ADDITIONAL WARRANTIES, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS OF EQUIPMENT FOR A PARTICULAR PURPOSE AND ANY SUCH WARRANTIES ARE EXPRESSLY DISCLAIMED. SHARK FURTHER DISCLAIMS ANY WARRANTY THAT THE PRODUCT PURCHASED BY CUSTOMER WILL MEET ANY PARTICULAR REQUIREMENT OF CUSTOMER EVEN IF SHARK HAS BEEN ADVISED OF SUCH REQUIREMENT. THE RIGHTS AND REMEDIES PROVIDED UNDER THIS WARRANTY ARE EXCLUSIVE AND IN LIEU OF ANY OTHER RIGHTS OR REMEDIES OF CUSTOMER. SHARK SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANY PERSON OR ENTITY INCLUDING, BUT NOT LIMITED TO, THE CUSTOMER OR ANY END USER OF THE PRODUCT FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ECONOMIC LOSS, LOSS OF PROFITS OR LOSS OF USE OF THE PRODUCT, ARISING IN CONNECTION WITH THE SALE, DELIVERY, INSTALLATION, TRAINING OR USE OF PRODUCT. SHARK’S LIABILITY, WHETHER IN CONTRACT OR IN TORT, ARISING OUT OF ANY WARRANTIES OR REPRESENTATIONS, INSTRUCTIONS OR DEFECTS FROM ANY CAUSE, SHALL BE LIMITED EXCLUSIVELY TO THE COST OF REPAIR OR REPLACEMENT PARTS UNDER AFORESAID CONDITIONS. The purpose of the foregoing limitations on liability and Customer remedies is to protect Shark from unknown or undeterminable risks. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to the Customer. Shark sales and service representatives are not authorized to waive or alter the terms of this warranty, or to increase the obligations of Shark under the warranty. Shark reserves the right to make design changes in any of its products without prior notification to the Customer. Shark HPB • 9.801-190.0 • Rev. 7/13 PRESSURE WASHER WARRANTY LIMITED NEW PRODUCT WARRANTY—COMMERCIAL PRESSURE WASHERS www.sharkpw.com Shark HPB • # 9.801-190.0 • Revised 7/13 • Printed in U.S.A. or Mexico ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Hot water system
- Detergent injector
- Variable pressure control
- High limit thermostat
- GFCI
- Pump protector
Frequently asked questions
Connect the detergent injector to the discharge nipple on the machine, connect the high pressure hose to the injector with the quick coupler, and then apply detergent to the work area. Be sure to follow the manufacturer's instructions for detergent use.
Use only detergents that are specifically designed for pressure washers. Household detergents can damage the pump.
Store the machine in a heated room, or mix a 50/50 solution of anti-freeze/water or windshield washer fluid with water and run the machine until the solution exits the discharge nipple.