I NST RUCT I ON M ANUAL
.
(GM082XM)
Wing Span: 48.8 in / 1240 mm
Wing Area: 338 sq in / 21.8 sq dm
Flying Weight: 25.8 oz / 730 g
Fuselage Length: 33.8 in / 858 mm
Requires: 4-channel radio w/ 5 mini servos
Outrunner Motor KM28251025 w/ Propeller Adaptor
HW2340100 20A Brushless ESC,9x6 Propeller,
3 cells 11.1V 1800 mAh Li-Po battery & charger.
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind of electric powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
.
GM082XMPO30231403
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
P.1
P.2
P.3-
P.15
SAFETY PRECAUTIONS
BEFORE YOU BEGIN
P.16
1 Read through the manual before you begin, so you will have an overall idea of what to do.
2 Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer. For pre-assembled kits, please check proper functions of all servos on the ground before flying. Servo gears could be damaged when control surfaces are hit during transportation of models. The manufacturer will replace any servos due to manufacturer`s defect, but will not cover plane crashes due to damaged servos not detected before flying.
3 Symbols used throughout this instruction manual comprise of the following :-
Apply epoxy glue.
Apply instant glue
(C.A.glue, super glue.)
Must be purchased separately !
Apply thread locker
Assemble left and right sides the same way.
Peel off shaded portion covering film.
3mm
Drill holes with the specified diameter (here: 3mm).
Pay close attention here!
GM082XMPO30231403
Ensure smooth non-binding movement while assembling.
Cut off shaded portion.
Pierce the shaded portion covering film.
Warning!
Do not overlook this symbol !
P.1
Parts List
1.DECALS: GM082XM DEC -- 1 set
MAIN WING -- 1 pair
STABILIZER -- 1 set
FUSELAGE -- 1 set
2.STABILIZER & ELEVATOR -- 1 set
HINGES PL4115050 -- 4 pcs
3.VERTICAL FIN & RUDDER -- 1 set
HINGES PLL4115050-- 3 pcs
4.DECALS FOR RUDDER - 1 set
10.MAIN LANDING GEAR Ø2.5mm -- 1 set
COLLAR Ø2.6mm w/ Set Screw -- 2 sets
MAIN WHEEL Ø40mm PL3116040 -- 2 pcs
SCREW PA2.3x8mm -- 1 pc.
PLYWOOD 21x26x2.5mm (For Main Landing Gear) -- 1 pc.
11.SOCKET HEAD SCREW M3x8mm -- 4 pcs
WASHER d3xD7mm -- 4 pcs
12.
HORN PL4113103 -- 2 pcs
HINGES PLL4115050-- 8 pcs
PLASTIC BRACKET -- 4 pcs
5.
6.
HORN PL4113103 -- 1 pc.
PLASTIC BRACKET -- 2 pcs
FUEL TUBE D2xD4x4mm -- 2 pcs
CLEVIS PL4112105 --1 pc.
STRAPER PL4112106 -- 1 pc.
PUSHROD Ø1.4x45mm w/ Threads (For Rudder) -- 1 pc.
13.
FUEL TUBE D2xD4x4mm -- 4 pcs
CLEVIS PL4112105 --2 pcs
STRAPER PL4112106 -- 2 pcs
PUSHROD Ø1.4x65mm w/ Threads (For Aileron) -- 2 pcs
14.WING TUBE Ø6x715mm -- 1 pc.
NYLON BOLT M3x20mm -- 2 pcs
7.
HORN PL4113103 -- 1 pc.
PLASTIC BRACKET -- 2 pcs
15.RECEIVER TIE 130mm -- 1 pc.
8.
FUEL TUBE D2xD4x4mm -- 2 pcs
CLEVIS PL4112105 --1 pc.
STRAPER PL4112106 -- 1 pc.
PUSHROD Ø1.4x60mm w/ Threads (For Elevator) -- 1 pc.
17.BATTERY TIE 200mm-- 1 pc.
BATTERY MAT 2x50x150mm-- 2 pcs
20.SPINNER Ø36mm SP27036FR0 -- 1 set
9x6 PROPELLERS PL6314050 -- 1 set
SCREW PM2x12mm -- 2 pcs
SCREW PA1.7x8mm -- 2 pcs 9.TAIL LANDING GEAR PL3410030 --1 set
SCREW PA2x8mm -- 2 pcs
TAIL WHEEL Ø23mm PL3510230 -- 1 pc.
21.BATTERY COVER -- 1 pc.
GM082XMPO30231403
P.2
1
Decals
Cut out decal sheet, peel off backing sheet and apply on fuselage, stabilizer and wings.
Decal
Fuselage
GM082XMPO30231403
P.3
2
Stabilizer & Elevator
Hinge Setting
Hinge
Section View Completed
Hinge
Bottom View
For pre-assembled version, the hinges are factory glued.
3
Vertical Fin & Rudder
Hinge Setting
Hinge
Section View Completed
Hinge
For pre-assembled version, the hinges are factory glued.
Right View
4
Decals for Rudder
Transparent decals to reinforce stabilizer.
Apply decal sheets on both sides to fasten rudder. Make sure no decal sheet cover the hinge gap. Check free movement of rudder before hooking up with rudder pushrod.
GM082XMPO30231403
P.4
5
Rudder Servo & Horn
Plastic Bracket
Servo wire
For pre-assembled version, the horn is factory glued and servo installed.
Horn
6
Rudder Pushrod
Straper
Plastic Stand
Horn
Fuel Tube d2xD4x4mm
Pushrod
Ø
1.4x45mm
Clevis
Fuel Tube d2xD4x4mm
7
Elevator Servo & Horn
Servo wire
Plastic Bracket
For pre-assembled version, the horn is factory glued and servo installed.
GM082XMPO30231403
P.5
Horn
8
Elevator Pushrod
Straper
Pushrod
Ø
1.4x60mm
Clevis
Fuel Tube d2xD4x4mm
Horn
Plastic Stand
9
Tail Landing Gear
PA2x8mm Screw
2
PA2x8mm
Wheel Ø23mm
Plastic
Collar
1.2mm
10
Main Landing Gear
PA2.3x8mm Screw
1
Fuselage
Landing Gear
10
0
3.1mm Collar
Wheel Ø40mm
M3x3mm
Set Screw Landing Gear
GM082XMPO30231403
PA2.3x8mm
P.6
Plywood
21x26x2.5mm
Bottom View
11
Motor & ESC
M3x8mm Socket Head Screw
4 d3xD7mm Washer
4
M3x8mm d3xD7mm Washer
EZ Connector
Brushless ESC
2-Pin EZ Connector
ESC
Solder
Solder
Motor
TWM
KP0011310
12
Aileron Servo & Horn
Hinge Setting
Servo wire
Plastic Bracket
Hinge
Section View Completed
Horn
Bottom View
Hinge
GM082XMPO30231403
For pre-assembled version, the hinges and horn are pre-glued, and servo installed.
Bottom View
P.7
13
Aileron Pushrod
15°
Fuel Tube d2xD4x4mm
Straper
Fuel Tube d2xD4x4mm
Clevis
Plastic Stand
Pushrod
Ø1.4x65mm
Horn
Bottom View
14
Main Wing
Wing Tube Ø6x715mm
Nylon Bolt M3x20mm
Servo wire
Insert carbon fiber wing tube into right wing, align the anchor holes and apply the nylon bolt.
Nylon Bolt M3x20mm
Insert the right wing into the Fuselage. Inset the left wing onto the carbon wing tube, press the wings against the fuselage align the anchor holes and apply the nylon bolt.
GM082XMPO30231403
P.8
15
Radio
180mm Y-Cord
3
4
1
2
5
6
ID SET
Receiver
Elevator Servo
ESC
Rudder Servo
Plug in the Aileron Servos wire to channel 1
Plug in the Elevator Servo wire to channel 2
Plug in the ESC Throttle wire to channel 3
Plug in the Rudder Servo wire to channel 4
Aileron Servo (L)
Aileron Servo (R)
Receiver Tie 130mm
16
Radio
Switch on radio
The power LED should turn on
Install battery
Elevator
Rudder
GM082XMPO30231403
Mode 1
Throttle
Aileron
P.9
Rudder
Mode 2
Elevator
Aileron
17
Battery & Motor Setting
Battery Mat
Battery Tie 200mm
2 Plug in battery wait a few seconds for the transmiter and receiver to bind.
Red Red
Black Black
Plug in with red+ / black- reversed will damage the ESC.
Battery ESC
TWM
KP0011210
Solder Solder
Mode 1
1
Pull throttle stick all the way back.
Mode 2
Mode 1 Mode 2
3 Advance throttle stick, the motor should start running, check motor shaft for rotating direction. The motor should be turning counter-clock wise. If rotating direction is not correct, unplug the 3-pin plug connecting the motor and ESC, swivel 180 ° and plug back, the rotation will be reversed.
18
Servos Setting
( For WMT6 radio only. Please refer to respective instruction manual if you are using other radio system. )
Please move the servo reverse switch for Aileron, AIL up to the REV position, and check the following.
Mode 1
Move aileron stick to right side
The left aileron should move down, and the right aileron should move up, the plane will bank right when flying.
Mode 2
Move aileron stick to right side
Mode 1
Move aileron stick to left side
GM082XMPO30231403
The left aileron should move up, and the right aileron should move down, the plane will bank left when flying.
P.10
Mode 2
Move aileron stick to left side
19
Servos Setting
Mode 1
Pull back Elevator stick Elevator should move up, plane will pull up when flying.
Mode 2
Pull back Elevator stick
Mode 1
Push foward Elevator stick Elevator should move down, plane will dive down when flying.
Mode 2
Push foward Elevator stick
Mode 1
Move Rudder stick to right side
The rudder should move to right, the plane will turn to right when flying.
Mode 2
Move Rudder stick to right side
Mode 1
Move Rudder stick to left side
The rudder should move to left, the plane will turn to left when flying.
Mode 2
Move Rudder stick to left side
GM082XMPO30231403
P.11
20
Propeller
1 Unplug battery
EZ Connector Puller
2 Switch off transmiter 3 Charge battery
The battery is ready for use when all the lights turn from red to green.
4 Install the propeller
Propeller Adaptor
(d3xD5) HW2340100
9x6 Propeller PL6314050
PM2x12mm
M5 Nut
Ø36mm Spinner
PA1.7x8mm
TWM HW3111400
PROPELLER ADAPTOR WRENCH
* Make sure you have unplugged the battery before working on the propeller.
GM082XMPO30231403
P.12
21
C.G.
Install battery onto the battery tray. Don`t plug in the battery yet. Put on the battery check C.G. mark underneath wings.
Support the model by two fingers on the C.G. mark, move battery position if necessary to balance the model on the
C.G. marks.
GM082XMPO30231403
P.13
22
Get Ready to fly
1 Turn on transwitter, throttle stick at low position.
2 Plug in battery.
Mode 1 Mode 2
Red Red
Black Black
Plug in with red+ / black- reversed will damage the ESC.
3 Wait a few seconds for the receiver to bind with transmitter.
4
5
Advance throttle stick slowly to check totation of propeller.
Mode 1 Mode 2
Check movement of Ailerons, Elevator and Rudder by moving the sticks as shown in Step 18 and Step 19.
GM082XMPO30231403
P.14
23
Flying
Try to get an experienced flyer to check through your installation before flying. Ask him/her to do the first flight for you. He/she can trim out the control surfaces for you so the model can fly straight and level with control sticks in neutral positions and throttle stick about half throttle. You will get a much higher successful rate with the help from an experienced flyer.
Before you fly, try to fine fune the control surfaces with Sub-trim tab.
1 Fine tune Elevator and Rudder with sub-trim tab.
Mode 1
Move Elevator Sub-trim tab up or down to bring elevator in a straight line with horizontal stabilizer.
Mode 2
Mode 1
Move Rudder Sub-trim tab left or right to bring rudder in a straight line with vertical stabilizer.
2 Fine tune Ailerons with sub-trim tab.
Mode 2
Mode 2 Mode 1
Move Aileron Sub-trim tab to bring Ailerons in a straight line with Wings.
GM082XMPO30231403
P.15
Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer
is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by KM28251025 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller. Extreme caution should be exercised when working with
electric powered models. Make sure the propeller is cleared of all objects, especially your
hands before connecting the battery to the model. Make sure you understand the
operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one,
as accidental movement of the throttle stick will spin the propeller and could cause injuries.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
GM082XMPO30231403
P.16
Pl8210010
180mm Y-Cord
Code No.
Size Package
KW0021800 180mm 1 pc
EZ Connector Puller
Code No.
Size Package
PL8210030 1 set
GM082XMPO30231403
Outrunner Motor
KM28251025
-Kv (rpm/V): 1025
-Operating Power: 110W
-Operating Voltage: 2-3S Li-Po
-Operating Current: 10A
-Peak Current: 15A (max. 15 sec.)
-Internal Resistance: 50 m ohms
-Diameter: 27.6mm
-Length: 25mm
-Weight: 40g
-Shaft Diameter: 3mm
-Shaft Length: 14 mm
-Mounting Screw:
M3 (Front)
-Distance of Mounting Holes:
16mm and 19mm
GM082XMPO30231403
www.thewingsmaker.com
GM082XMPO30231403
THE WINGS MAKER
