SC35.MX44
4×4 HDMI 18Gbps Over
HDBaseT Matrix
VER 1.1
Thank you for purchasing this product
For optimum performance and safety, please read these instructions carefully
before connecting, operating or adjusting this product. Please keep this manual
for future reference.
Surge protection device recommended
This product contains sensitive electrical components that may be damaged
by electrical spikes, surges, electric shock, lighting strikes, etc. Use of surge
protection systems is highly recommended in order to protect andextend the
life of your equipment.
Table of Contents
1. Introduction........................................................................................... 1
2. Features................................................................................................. 1
3. Package Contents................................................................................ 1
4. Specifications....................................................................................... 2
5. Operation Controls and Functions...................................................... 3
5.1. Front Panel.................................................................................... 3
5.2. Rear Panel..................................................................................... 3
6. HDBaseT Receiver Panel...................................................................... 5
7. IR Control system.................................................................................. 6
8. Remote Control..................................................................................... 8
9. Web GUI User Guide............................................................................ 9
10. Application Example..........................................................................13
1. Introduction
The 4x4 HDBaseT Matrix supports the transmission of video (up to 4K2K@
60Hz, 18Gbps, HDCP 2.2) and multi-channel digital audio from 4 HDMI
sources to 3 HDBaseT-Lite outputs and 1 independent HDMI 2.0 output. It
supports audio de-embedding from any one of 4 outputs (configurable). Any
source can be selected it via on-panel button, IR remote control, RS-232,
LAN or Web GUI.
2. Features
☆ HDMI 2.0b, HDCP 2.2 and HDCP 1.4 compliant.
☆ Up to 4K2K@60Hz (4:4:4) on all HDMI and HDBaseT ports.
☆ Supports pass-through audio up to 7.1 channels of High Definition audio
(LPCM, Dolby TrueHD, and DTS-HD Master Audio).
☆ Digital and analog audio de-embedding from any one of 4 outputs
(configurable).
☆ HDR and smart EDID management supported.
☆ 24V POC on all HDBaseT ports.
☆ Control is via on-panel Button, IR, RS-232, LAN and Web UI.
☆ Transmission distance: Over CAT6 cable
70 meters: 1080P @60Hz36bit;
40 meters: 1080P @60Hz@48bit; 1080P @120Hz@24bit;
4K2K@50/60Hz (YUV420), 4K2K@50/60Hz (YUV444).
3. Package Contents
① 1× 4×4 HDMI 18Gbps over HDBaseT Matrix
② 3× HDBaseT receivers
③ 2× Mounting Ears (Matrix)
④ 6× Mounting Ears (Receiver)
⑤ 4× Phoenix terminals (male)
⑥ 8× Wideband IR Receiver cables
⑦ 8× Wideband IR Blaster cables
⑧ 1× 24V/2.7A Locking Power Adaptor
⑨ 1× IR Remote control
⑩ 1× User Manual
1/13
4. Specifications
Technical
HDMI Compliance
HDMI 2.0b
HDCP Compliance
Video Bandwidth
HDCP 2.2 and HDCP 1.4
Up to 18Gbps
Up to 4K2K@50/60Hz(YUV4:4:4), 4K2K@30Hz,
Video Resolution
1080P@120Hz and 1080P 3D@60Hz
Color Space
RGB, YCbCr 4:4:4, YCbCr 4:2:2
Color Depth
10-bit, 12-bit
LPCM2/5.1/7.1CH, Dolby Digital, DTS 5.1, Dolby
HDMI Audio Formats
Digital+, Dolby TrueHD, DTS-HD Master Audio,
(Pass-through)
Dolby Atmos, DTS:X
Human-body Model: ±8kV (Air-gap discharge) ,
ESD Protection
±4kV (Contact discharge)
Connections
Input Ports: 4×HDMI Type A (19-pin female)
6×IR IN (3.5mm Stereo Mini-jack)
1×RS-232 (Phoenix jack)
1×LAN (RJ45)
Transmitter
Output Ports: 1×HDMI Type A (19-pin female)
3×HDBaseT (RJ45)
1×SPDIF (Optical)
1×L/R (3.5mm Stereo Mini-jack)
5×IR OUT (3.5mm Stereo Mini-jack)
Input ports: 1×HDBaseT In [RJ45]
1×IR In [3.5mm Stereo Mini-jack]
Receiver
Output ports: 1×HDMI Type A [19-pin female]
1×IR Out [3.5mm Stereo Mini-jack]
1×RS-232 [Phoenix connector]
Mechanical
Chassis Material
Silkscreen Color
Metal
Black
Weight
Power Supply
TX: 360mm (W)×160mm (D)×35mm (H)
RX: 115mm(W)×65mm(D)×17mm(H)
TX: 1.9kg, RX: 206g
DC 24V/2.7A
Power Consumption
35W(max) / 1W（Standby）
Dimensions
2/13
Operating Temperature 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature -20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity
20~90% RH (non-condensing)
5. Operation Controls and Functions
5.1 Front panel
"
1
Name
Number
#
$
2
3 4
%
3
4
5
Function description
1
LED
2
Nixie tube
When device is in standby mode, the LED light in red.
LED is blanking when device is working normally.
Displaying output port corresponding input source.
3
IR
IR receive window.
4
POWER button Power on/off button.
5
OUTPUT button A/B/C/D output channel button.
5.2 Rear panel
4
1
Number
1
2
2
Name
3
3 4
5
6
7
8
Function description
Connect to the HDMI source device, such as DVD
HDMI INPUT
player or Set top box.
Connect to the HDMI display devices, such as TVs
HDMI
or Monitors.
Connect to HDBaseT receiver comes from the
OUTPUT
same package. Don't connect to a projector directly
HDBaseT
that built-in HDBaseT input port since 24V POC
may destroy this projector.
3/13
3
4
AUDIO OPTICAL Digital audio de-embedding output.
OUTPUT L/R
Analog L/R audio de-embedding output.
If the front IR sensor of unit is obstructed or the
unit is installed in a closed area out of infrared line
of sight, the IR receiver included can be inserted
IR EXT
into the IR EXT port at the rear to extend the IR
sensor range and enable local of the matrix.
5
IR INPUT
IR receiver port, connect an IR receiver cable.
6
IR OUTPUT
IR blaster port, connect an IR blaster cable.
Connect to an active Ethernet link with an RJ45
terminated cable.
CONTROL
Connect to an PC or control system for control via
RS-232
a Phoenix terminal to transmit command.
Plug the 12V DC power supply into the unit and
Power port
connect the adapter to AC wall outlet.
LAN
7
8
Notice：The following is the EDID schema table.
EDID mode
EDID description
1
720p,Stereo Audio 2.0
2
1080p,Stereo Audio 2.0
3
1080p,Dolby/DTS 5.1
4
1080p,HD Audio 7.1
5
1080i,Stereo Audio 2.0
6
1080i,Dolby/DTS 5.1
7
1080i,HD Audio 7.1
8
3D,Stereo Audio 2.0
9
3D,Dolby/DTS 5.1
10
3D,HD Audio 7.1
11
4K2K30_444,Stereo Audio 2.0
12
4K2K30_444,Dolby/DTS 5.1
13
4K2K30_444,HD Audio 7.1
14
4K2K60_420,Stereo Audio 2.0
15
4K2K60_420,Dolby/DTS 5.1
4/13
16
17
4K2K60_420,HD
Audio 7.1
3
4K2K60_444,Stereo Audio 2.0
18
4K2K60_444,Dolby/DTS 5.1
19
4K2K60_444,HD Audio 7.1
6 HDBaseT Receiver Panel
8
1
3
2
Number
9
Name
1
POWER
2
DC 24V
3
HDBaseT IN
4
HDMI OUT
5
IR IN
6
IR OUT
7
RS-232
4
5
6
7
33 44
Function description
This LED illuminates when the device is
connected with power supply.
Plug the 24V DC power supply into the unit.
(If the device connect to the matrix, the receiver doesn't
need local power supply due to POC from the matrix.)
Standard HDBaseT signal input port. Connect
to Matrix HDBaseT output with a UTP cable.
HDMI output port. This slot is
where you connect
the HDTV or monitor with HDMI cable.
Channel 1 IR Receiver. Connect with Wideband
IR Rx.
Channel 2 IR Transmitter. Connect with
Wideband IR Tx.
Connect to a PC or control system with phoenix
jack for transmission of RS-232 commands.
5/13
8
Connection Signal
Indicator Lamp
9
Data Signal
Indicator Lamp
Illuminate: The Transmitter and Receiver
are in good connection status.
Flashing: The Transmitter and Receiver are
in poor connection status.
Dark: The Transmitter and Receiver are not
connected.
Illuminate: The HDMI signal with HDCP.
Flashing: The HDMI signal without HDCP.
Dark: No HDMI signal.
7. IR Control system (IR Call-back of Matrix and Source Devices)
#
$
%
IR Path
IR Path
CAT5e/6/7
IR TX
HDMI
"
IR Path
IR RX
IR TX
HDMI
IR RX
The matrix is not only a switcher and extender
of multiple HDMI signals to multiple HDMI
receivers located remotely, it also passes IR
control signals through the IR call-back system
to the matrix and HDMI sources for full, independent control of all connected inputs from
output locations.
Two-way IR Call-back Between matrix, Sources
and displays from multiple locations.
A key feature on the matrix is discrete IR control
of the matrix, sources and displays from any
location – so inputs at the matrix end can be
controlled at a display location and displays can
be controlled at the matrix location. This is accomplished by placing a series
of IR Emitters on devices to control and IR Receivers at all locations you wish
to control from to enable the IR signal to travel both ways via the single Cat5e/
6/7 cable.
6/13
IR control is devided into two kind of control ways as below.
Insert the 3.5mm IR receiver cable into IR INPUT ports at the rear of the
matrix. At the same time, insert the 3.5mm IR blaster cable into IR OUTPUT
ports at the rear of the matrix. At the display, the user connect HDBT Receiver
device at the matix HDBaseT ports Afterwards, insert the 3.5mm IR receiver
cable and IR blaster cable to the HDBT Receiver device.
① At Matrix end: When the user control the output device by remote control.
The matrix IR INPUT and the HDBT IR output is match. The way of IR control
is following video switch to change. The mean is that the HDMI source is switched to the
HDBT receiver display device output, the IR control will switch to following output select
corresponding input source.
② At display end: The matrix has one location HDMI output and three HDBT
outputs. The location HDMI output has not IR control function. The three HDBT
outputs connect HDBT receiver. The HDBT IR INPUT and the matrix IR
OUPTU is match. The way of IR control is following video switch to change.
The mean is that the output select corresponding input source, the IR control
will switch to following output select corresponding input source.
Attention: The matrix has one location HDMI output. If the HDMI input source is
switched to the one location HDMI output, the HDMI output end has not control
the matrix through IR.
The function of the IR “ALL” port is control about one to all port.
7/13
IR Pin Definition
IR Receiver and Blaster pin’s definition as below:
IR RECEIVER
IR BLASTER
8. Remote control
① Press this button to open the power of the
matrix or set it as a standby status.
② Press these keys to select the output A,
output B, output C or output D for output
corresponding 1, 2, 3 or 4 input source.
1
Output A
1
3
4
3
4
2
3
4
2
3
4
2
Output B
1
2
Output C
1
2
Output D
1
HDMI Matrix Remote
8/13
9. Web GUI User Guide
The Matrix can be controlled via Web GUI through LAN port. You must know
current Matrix IP address. The static IP address is 192.168.1.100. You can
connect PC Web GUI through dynamic IP adress. In this unit, you can get the
IP address via PC Controller. Firstly, opening Matrix PC Controller software,
as following page:
Then select the “TCP Control Mode” port, click the “Search” button. At this
moment, you can get current IP address. You can set the IP address to your
PC/laptop/mobile Internet Explorer and click “Search” to enter Web GUI page.
The Web GUI likes below:
9/13
General page
2
3
1
8/12
4
5
① Display currently the Matrix input and output port status. The “yes” have
connected input or output source and “no” represent not connection.
② Power switch. The Matrix will work when open this switch, otherwise, the
Matrix will standby.
③ Beep switch. Open this switch, press the Matrix on-panel button will
have voice. Close this switch, it will mute.
④ Click this button will reboot device.
⑤ Click this button will set to factory reset.
Control page
1
2
① Select the input source to the output port.
② Select the output port audio.
10/13
EDID page
1
2
3
4
① Set EDID mode to input source, then click “Set” button.
② Copy EDID from HDMI output port to input source, then click “Set” button.
③ Open EDID file to input source, then click “Set” button.
④ Click “Refresh” button to refresh currently EDID mode. It will diaplay
currently input source EDID mode status.
Status page
1
2
① Network Configuration
◆ In DHCP open status:
HDCP switch: Obtian the network configuration information, including IP
address, Subnet, Gate. Then click “Save Changes” button to save DHCP
status.
11/13
◆ In DHCP close status:
HDCP switch: If the DHCP switch has been closed, user can set IP, Subnet
and Gate address. In this moment, click the “Save Change” button to save
current status information. (Attention: If user have set the IP address, click
the “Save Change” button. In this moment, user need set the IP address
again to your PC/laptop/mobile Internet Explorer and click “Search” to enter
Web GUI page.)
Net Status button: Press this button refresh current network configuration
information to display in the status log.
In this unit, Mac address can check only, you can not set it.
② Display the network configuration information.
Upgrade page
1
① Open upgrade file to upgrade.
12/13
10. Application Example
IR Receiver
UHDTV
IR Blaster
RS-232 Equipped/HDMI Matrix
Computer
Receiver
Transmitter
Power Supply
DVD or Blu-ray Player
Active Speakers
13/13
">
