JWP
Weighing Scales
JWP digital weighing scales operation manual
REV: C1, June 2012
JWP digital weighing scales operation manual
JWP digital weighing scales operation manual
REV: C1, June 2012
JWP digital weighing scales operation manual
As the battery is used it may fail to hold a full charge. If the battery life
becomes unacceptable then contact your distributor.
Note: new batteries are shipped partially charged. Before you can use
your scale, you need to install and charge the battery, as indicated by the
following instructions.
Some batteries perform best after several full charge/discharge cycles.
Battery performance depends on many factors, including your backlight
setting and operate.
Contents
1 INTRODUCTION……………………………………………………1
2 KEY DESCRIPTIONS………………………………………….……2
3 BASIC OPERATION…………………………………………….…..3
3.2 Taring……………………………………………………..…….3
3.3 Weighing a sample……………………………..…………….4
9 CALIBRATION
Turn on the scale and press % and TARE key during the self test..
Display will be shown ”UNLOAD”
Remove all weight from the platform.
Press ZERO to confirm when display gets stable.
Display will be show previous calibration weight and start to blink first
digit, if necessary enter the calibration weight value by pressing LIM and
TARE keys.“10.000”
Press ZERO to confirm, display will be show ”LOAD”
Place the load on the platform.
Press ZERO to confirm when display gets stable.
Calibration will be finish and will start to self test to come normal
weighing.
Note: Calibration weight should be 1/3rd of the scale capacity.
-10-
4 PRECENT WEIGHING………………………………………...…….4
5 PARTS COUNTING………………………………………..…..…….7
6 CHECK-WEIGHING………..…………………………………..…….7
7 ACCUMULATED TOTAL………..……………………………….….7
7.1Manual accumulation………..………………………….…….8
7.2 Automatic accumulation……..……………………………...8
8 BATTERY OPERATION………………………………..………..….9
9 CALIBRATION………………………………..………….……..….10
JWP digital weighing scales operation manual
JWP digital weighing scales operation manual
REV: C1, June 2012
value when the weight is removed.
The totals can be viewed as above.
In all cases the scale must return to zero or a negative number before
another sample can be added to the memory.
More product can then be added and PRINT pressed again. This can
continue for up to 99 entries, or until the capacity weight display isexceeded.
8 BATTERY OPERATION
The scales can be operated from the battery if desired. The battery life is
approximately 70 hours.
When the battery needs charging the arrow above the low battery symbol
under the weight display will turn on. The battery should be charged as soon
as the arrow above the symbol is on.
The scale will still operate for about
30 minutes after which it will automatically switch off to protect the battery.
(during low battery term, display will show “BAT LO” every 5 minutes.)
To charge the battery simply plug into the AC adapter. The scale does
not need to be turned on.
The battery should be charged for 12 hours for full capacity.
Just above the display is an LED to indicate the status of battery charging.
When the scale is plugged into the mains power the internal battery will be
charged. If the LED is green the battery has a full charge. If it is Red the
battery is nearly discharged and yellow indicates the battery is being
charged.
-9-
JWP digital weighing scales operation manual
The display will show "ACC
JWP digital weighing scales operation manual
REV: C1, June 2012
1" and then the total in memory for 2
seconds before returning to normal. If the optional RS-232 interface is
installed the weight will be output to a printer or PC.
1 INTRODUCTION
The JWP series of scales provides an accurate, fast and versatile series of
general
Remove the weight, allowing the scale to return to zero and put a
second weight on. Press PRINT, the display will show "ACC
2" and
then show the new total. Continue until all weights have been added.
To view the totals in memory press the PRINT key when the scale is at
purpose
weighing
scales
with
counting, % weighing
and
check-weighing functions. The scales built in a thermal printer that could
support continuous paper. And also, they have an expanded bi-directional
RS-232 interface for communication with a PC as an optional.
There are 4 models in each series, with capacities up to 45 kg.
They all have stainless steel weighing pan assembly.
zero.
The display will show the total number of items "ACC xx" and the total
weight before returning to zero. The totals will also be
are supplied with a backlight.
printed via the RS-232 interface.
To erase the memory press PRINT to view the totals and then press the
All units include automatic zero tracking, audible alarm for pre-set weights,
automatic tare, and an accumulation facility that allows the count to be stored
SMPL/C key to clear the memory.
Note: M+/Print function only available when stable (
All the keypads are sealed, color coded membrane switches and the
displays are large easy to read liquid crystal type displays (LCD). The LCD’s
and recalled as an accumulated total.
indicator on)
2 KEY DESCRIPTIONS
7.2 AUTOMATIC ACCUMULATION
When the scale has been set to Automatic Accumulation the value is
stored in memory automatically.
Add a weight to the scale, the beeper will sound when the scale is stable to
signify the value is accepted. Remove the weight.
The display will show "ACC 1" and the totals in memory when the scale
returns to zero.
Adding a second weight will repeat the process.
While the weight is on the scale it is permissible to press the PRINT key
to store the value immediately. In this case the scale will not store the
-8-
Zero or
Set the zero point for all subsequent weighing. The display shows zero.
A secondary function
, of "Enter" key when setting parameters or
other functions.
Tare or
Tares the scale. Stores the current weight in memory as a tare value,
subtracts the tare value from the weight and shows the results. This is
the net weight. Entering a value using the keypad will store that value as
the tare value. A secondary function + , of incrementing the active digit
-1-
JWP digital weighing scales operation manual
JWP digital weighing scales operation manual
REV: C1, June 2012
when settinga value for parameters or other functions.
HIGH LIMIT SET,
Lim or
Sets the limits for check weighing. Allows setting of either the low limit
High Limit. Above the High Limit the display will show OK.
or the high limit or both.
Secondary function
LOW LIMIT is set to zero
The display will show LOW when the weight is less than the
BOTH LIMITS SET.
, is to move the active digit to the right when setting
LOW IS SET GREATER THAN HIGH
The beeper will never sound and the display will show LOW if the weight is
values for parameters or other functions.
less that the LOW limit, and HIGH if the weight is
%
greater than the Low Limit.
Enters the percent weighing function. Allows the weight, unit weight,
and count to be seen when parts counting.
Secondary function
, is to move the active digit to the left when setting
To disable the Check-Weighing function enter zero into both limits by
pressing the SMPL/C key when the current limits are shown then pressing
values for parameters or other functions.
Smpl or
If the scale is weighing it will select parts counting.
NOTE: The weight must be greater than 20 scale divisions for the
checkweighing to operate.
the ZERO/ENTER key to store the zero values.
Of it is not in
weighing mode it will return the user to weighing.
Secondary function ( C ) , is to act as a clear key when setting values
for parameters or other functions.
Print or
To print the results to a PC using the optional RS-232 interface or printer.
It also adds the value (weight or quantity) to the accumulation memory if
7 ACCUMULATED TOTAL
The scale can be set to accumulate automatically when a weight is
added to he scale or manually by pressing the PRINT key.
See the
PARAMETERS Section for details of selecting the method.
The
accumulation function is only available when weighing. It is disabled during
percent weighing or parts counting.
the accumulation function is not automatic.
Secondary function (ESC) , is to return to normal operation when the scale
is in a parameter setting mode.
Mode
In the counting mode, press this key to display the unit weight/count/total
-2-
7.1 MANUAL ACCUMULATION
When the scale is set to manual accumulation the weight displayed will
be stored in memory when the PRINT key is pressed and the weight is
stable.
-7-
JWP digital weighing scales operation manual
when the weight
JWP digital weighing scales operation manual
REV: C1, June 2012
on the scale meets or exceeds values stored in
memory. The memory holds values for a high limit and a low limit. Either
limit can be used or both can be used.
weight. In the weighing mode, press this key to shift the unit. In the
percent .
weighing mode, press this key to display the weight temporary then after 3
Press the LIMIT key. The display will show the current High Limit with
seconds back to the percent weighing mode.
the left most digit flashing and the HI symbol on to the left of the display..
To change the value shown use the %/
and the LIMIT/ to select
the digit to change. Then use the TARE/ key to increment the flashing
3.BASIC OPERATION
3.1 ZEROING THE DISPLAY
digit. When the desired value is shown press the ZERO/ENTER key to
You can press the ZERO/ENTER key at any time to set the zero point
accept the value. If you want to reset the value to zero press the SMPL/C
from which all other weighing and counting is measured, within 4% of power
key to clear the value.
up zero. This will usually only be necessary when the platform is empty.
After pressing the ZERO/ENTER key the display will then show the
Low Limit, the LO symbol will be on to the left side of the display.
Enter the low limit in the same way the high limit was entered.
When the zero point is obtained the display will show the indicator for zero.
The scale has an automatic rezeroing function to account for minor
drifting or accumulation of material on the platform. However you may need
After pressing the ZERO/ENTER key the scale will return to weighing with
to press the ZERO/ENTER key to rezero the scale if small amounts of
the Check-weighing function enabled.
weight are shown when the platform is empty.
When a weight is placed on the scale the arrows will show if the weight
is above or below the limits and the beeper will sound as your setting (see
detail in section 9).
BOTH LIMITS SET
The display will show OK when the weight is between the limits.
LOW LIMIT SET, HIGH LIMIT is set to zero
3.2 TARING
Zero the scale by pressing the ZERO/ENTER key if necessary. The zero
indicator will be on.
Place a container on the platform, a value for its weight will be displayed.
Press the TARE key to tare the scale. The weight that was displayed is
stored as the tare value and that value is subtracted from the display, leaving
The display will show OK when the weight is less than the Low Limit.
zero on the display. The "NET" indicator will be on. As product is added only
Above the Low Limit the display will show HIGH.
the weight of the product will be shown. The scale could be tared a second
time if another type of product was to be added to the first one.
-6-
-3-
JWP digital weighing scales operation manual
JWP digital weighing scales operation manual
REV: C1, June 2012
Again only the weight that is added after taring will be displayed
show 100 %, however a small change of weight will cause the display to
When the container is removed a negative value will be shown. If the scale
was tared just before removing the container this value is the gross weight
of the container plus all product that was removed. The zero indicator will
also on because the platform is back to the same condition it was when
the ZERO/ENTER key was last pressed.
jump to 102.13% as one scale division (0.5g) increase to 24.0g will be
equivalent to a 2.13% increase.
Removing the 350g weight and putting a 300g weight on the scale the
display will show 85.71% as 300g is 85.71% of 350g.
Pressing the SMPL key will return the scale to weighing.
3.3 Weighing a sample
To determine the weight of a sample first tare the empty container then
place the sample in the container. The display will show the weight and
the units of weight currently in use.
5 PARTS COUNTING
When the scale is showing weight, pressing the SMPL key will start the
parts counting function.
Press the SMPL key to begin. The scale will show "SP
4 PERCENT WEIGHING
The scale will allow a sample weight to be shown as 100%. Then any
other weight placed on the scale will be displayed as a percentage of the
original sample. For example is 350g is placed on the scale and the %
for a sample size of 10 parts. Change the sample size by pressing the
TARE/ key. the display will cycle through the options: 10,20, 50, 100,
200 and back to 10.
Press the ZERO/ENTER key when the number matches the number of
parts used for the sample.
key is pressed the display will show 100.00%.
Removing the 350g weight and putting a 300g weight on the scale the
display will show 85.71% as 300g is 85.71% of 350g.
10" asking
As more weight is added the display will show
the number of parts (pcs). Press the MODE key to
display unit weight (g/pcs),
Total weight (kg) or the count (pcs).
Press the SMPL key to return to normal weighing.
Note: the scale may jump by large numbers unexpectedly if small
weights are used to set the 100% level.For example if only 23.5g is on a
scale with 0.5g increments and the scale is set to 100%, the display will,
-4-
6 CHECK-WEIGHING
Check- weighing is a procedure to cause an alarm to sound
-5-
">
