Strata DK96 User Manual

Document

STRATA DK

ELECTRONIC TELEPHONE USER GUIDE

Release 1, 2, 3, and 4

© COPYRIGHT 1992 TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

All rights reserved. No part of this manual may be reproduced in any form or by any means — graphic, electronic, or mechanical, including recording, taping, photocopying, or the use of information retrieval systems — without express written permission of the publisher of this material.

Check with your Telephone System Administrator to find out which software release is installed for your Strata DK 24/56/96 telephone system. Enter the release version number below.

Release _________

Issue 1, September 1992

STRATA DK

TRADEMARKS AND SERVICE MARKS

The following trademarks and service marks are used in this document:

■ STRATA

: registered trademark of Toshiba America Information Systems, Inc.

In accordance with U.S. Copyright Law, a license may be required from the American Society of Composers,

Authors, and Publishers, or other similar organization, if radio or television broadcasts are used for the Musicon-Hold feature of this telecommunications system. Toshiba America Information Systems, Inc. disclaims any liability arising out of the failure to obtain such a license.

Toshiba America Information Systems, Inc. reserves the right to change any of this information including, but not limited to, product characteristics and operating specifications, without prior notice.

STRATA DK TABLE OF CONTENTS

SUBJECT PAGE

INTRODUCTION

General Description .......................................................................................................... v

Purpose ............................................................................................................................ v

Organization ..................................................................................................................... v

How to Use This Guide..................................................................................................... vi

CHAPTER 1

GENERAL INFORMATION ................................................................................................... 1-1

Purpose ............................................................................................................................ 1-1

Feature Buttons ................................................................................................................ 1-1

Volume Controls ............................................................................................................... 1-5

LED Indications................................................................................................................. 1-5

CHAPTER 2

FEATURE OPERATION ...................................................................................................... 2-1

Outside Calls .................................................................................................................... 2-1

On-hook Dialing ................................................................................................................ 2-3

Outside Calls ................................................................................................................ 2-3

Intercom Calls .............................................................................................................. 2-3

Group Listening ................................................................................................................ 2-4

Automatic Off-hook Selection ........................................................................................... 2-5

Repeat Last Number Dialed ............................................................................................. 2-5

Automatic Busy Redial...................................................................................................... 2-5

Speed Dial ........................................................................................................................ 2-7

Station Speed Dial Storage .......................................................................................... 2-7

System Speed Dial Storage ......................................................................................... 2-8

Speed Dial Pause and Flash Storage .......................................................................... 2-9

Speed Dial Number Linking.......................................................................................... 2-9

Calling System or Station Speed Dial Numbers........................................................... 2-10

Chain Dialing Speed Dial Numbers.............................................................................. 2-11

Saved Number Redial....................................................................................................... 2-12

DTMF Tone Dialing With * and # ..................................................................................... 2-12

Tone/Pulse Dialing ............................................................................................................ 2-13

Privacy Override .............................................................................................................. 2-13

Privacy Button (Release 3 and higher) ............................................................................. 2-14

Privacy Release................................................................................................................ 2-14

Intercom Calls................................................................................................................... 2-15

Handsfree Answerback..................................................................................................... 2-16

Microphone Cut-off ........................................................................................................... 2-17

Off-hook Call Announce (OCA) ........................................................................................ 2-17 i

STRATA DK TABLE OF CONTENTS

SUBJECT PAGE

Forced Disconnect........................................................................................................ 2-18

Call Transfer with Camp-on .............................................................................................. 2-18

Answering a Transferred Call ....................................................................................... 2-19

Conference Calls .............................................................................................................. 2-21

Conference with Stations and CO Lines ...................................................................... 2-21

Conference with Stations Only ..................................................................................... 2-22

Call Forward ..................................................................................................................... 2-23

Call Forward-All Calls ................................................................................................... 2-23

Call Forward-Busy (Release 2 and higher) .................................................................. 2-24

Call Forward-No Answer (Release 2 and higher) ......................................................... 2-24

Call Forward-Busy/No Answer (Release 2 and higher) ................................................ 2-25

Call Forward-Fixed ....................................................................................................... 2-26

Call Hold ........................................................................................................................... 2-26

Call Park ....................................................................................................................... 2-27

Exclusive Hold .................................................................................................................. 2-28

Call Pickup........................................................................................................................ 2-28

Directed Call Pickup ..................................................................................................... 2-29

Do Not Disturb .................................................................................................................. 2-30

Automatic Callback .......................................................................................................... 2-30

CO Line Queuing with Automatic Callback................................................................... 2-31

Account Code Calls .......................................................................................................... 2-32

Forced Account Codes ................................................................................................. 2-32

Emergency Override of Forced Account Codes .......................................................... 2-33

Voluntary Account Codes ............................................................................................. 2-33

Verified Account Codes ............................................................................................... 2-34

Paging............................................................................................................................... 2-35

All Call Page Button...................................................................................................... 2-36

Door Phone....................................................................................................................... 2-36

Handsfree Monitoring ....................................................................................................... 2-38

Alarm Reset...................................................................................................................... 2-38

Background Music (BGM) Over Telephone Speakers ...................................................... 2-39

Background Music (BGM) Over External Speakers ......................................................... 2-39

Direct Inward System Access (DISA) (Release 2 and higher).......................................... 2-40

DISA Security Code Entry/Change/Cancel ................................................................. 2-41

Direct Station Selection Buttons (Hotline)......................................................................... 2-42

Door Lock ......................................................................................................................... 2-42

Message Waiting .............................................................................................................. 2-43

Night Transfer ................................................................................................................... 2-44

Override Calls ................................................................................................................... 2-45

Speakerphone .................................................................................................................. 2-46

Outside Calls ................................................................................................................ 2-46

Tone/Voice First Signaling ............................................................................................ 2-47 ii

STRATA DK TABLE OF CONTENTS

SUBJECT PAGE

Intercom Calls ................................................................................................................ 2-47

Microphone Control ............................................................................................................ 2-48

Two (Tandem) CO Line Connection.................................................................................... 2-49

Supervision .................................................................................................................... 2-50

Timed Reminders ............................................................................................................... 2-50

Toll Restriction Override/Traveling Class ........................................................................... 2-51

Toll Restriction Override/Traveling Class Code Revision .................................................... 2-52

Automatic Hold .................................................................................................................. 2-52

User Programmable Feature Buttons ................................................................................ 2-53

Feature Access Code Record ............................................................................................ 2-55

CHAPTER 3

TOSHIBA VP INTEGRATION .................................................................................................

3-1

Using The Toshiba VP System ...........................................................................................

3-1

Call Forward .......................................................................................................................

3-1

Voice Mail Identification Code ........................................................................................

3-1

Call Forward to Toshiba VP Voice Systems ...................................................................

3-2

Message Retrieval ..............................................................................................................

3-3

CHAPTER 4

CENTREX APPLICATION ......................................................................................................

4-1

General...............................................................................................................................

4-1

Flexible Intercom Numbering .........................................................................................

4-1

Centrex Feature Buttons ................................................................................................

4-1

Ringing Repeat ..............................................................................................................

4-1

Delayed Ringing .............................................................................................................

4-1

APPENDIX

Customized Listings................................................................................................................ A-1

Speed Dial Code Assignments........................................................................................... A-2

System Speed Dial Code Assignments ......................................................................... A-2

Station Speed Dial Code Assignments .......................................................................... A-2

Account Codes ................................................................................................................... A-3

Paging ................................................................................................................................ A-3

GLOSSARY ...................................................................................................................................

Glossary-1 iii

STRATA DK TABLE OF CONTENTS

SUBJECT PAGE

INDEX ...................................................................................................................................................

Index-1

FIGURE LIST

TITLE FIGURE

I -1

I -2

PAGE

Sample Page.........................................................................................................................

vii

20-button Electronic Telephone.............................................................................................

viii

TABLE LIST

TABLE

2-A

TITLE PAGE

Feature Access Code List ..................................................................................................... 2-55 iv

Introduction

STRATA DK INTRODUCTION

GENERAL DESCRIPTION

Toshiba electronic telephones incor porate state-of-the-ar t telecommunications technology and are designed to provide you with a vast array of calling features. They are easy to operate, and all features are accessed by either pushing a feature button or dialing a brief access code.

PURPOSE

This document is designed as a feature operating guide for Toshiba electronic telephone users within a STRATA DK24, DK56, or DK96 system operating with either Release 1, Release 2, Release 3, or

Release 4 software.

Each electronic telephone voice calling feature is addressed in this user guide. Your telephone may be equipped with a Liquid Crystal Display

(LCD) for a variety of messaging features. See the Electronic Telephone

LCD User Guide for LCD feature operation.

ORGANIZATION

This user guide is divided into the following sections.

The Introduction consists of a general description of the electronic telephones, as well as the purpose and organization of this document.

Suggestions on how to use this user guide also appear in this section.

Chapter 1, "General Information," provides descriptions of the functions of all the feature buttons along with their associated Light Emitting

Diodes (LEDs) available to the telephones.

Chapter 2, "Feature Operation," contains descriptions and operating procedures for all of the voice calling features available with the telephones.

Chapter 3, "Toshiba VP Integration," explains how to set up your telephone to forward calls to a Toshiba Voice Processing System and to retrieve recorded messages left by callers.

Chapter 4, "Centrex Application," describes the Centrex features which may be available with your STRATA DK system.

STRATA DK INTRODUCTION

The Appendix provides space to record customized feature access codes, Speed Dial numbers, and more.

A glossary and an index are located at the end of the user guide.

HOW TO USE THIS GUIDE

Most of the features in this guide are available with your telephone.

Software limitations and programming assignments may deny you access to some of them. Your system administrator can tell you which features you can access.

The information in this user guide is divided into distinct areas of content.

Instructions for various procedures are referred to as Action Text and appear in the left-hand column of the page. Instructions appear in numerical sequence, enabling you to quickly perform a specific task.

More detailed descriptions of these procedures, or explanations of their effects, are located in the right-hand column. Figure I -1 shows you the structure followed for each feature operation.

STRATA DK INTRODUCTION

ACTION TEXT

SPECIFIC INSTRUCTIONS ON HOW TO PERFORM A

PROCEDURE ARE NUMBERED AND ENTERED IN

THE LEFT-HAND COLUMN.

NOTES AND

WARNING

MESSAGES

STRATA DK FEATURE OPERATION

AUTOMATIC OFF-HOOK SELECTION

Automatic Off-hook Selection allows you to access a specific line or line group just by lifting the handset or pressing the SPEAKER button. This is an optional feature enabled in system programming.

To Make a Call:

1. Lift the handset or press the

SPKR button.

You will be connected to the option programmed.

If you hear silence, you must press the INT button or a CO or PL button before dialing the telephone number

2. Dial a telephone number, and proceed with your call.

NOTE: If your station is programmed with Ringing Line Preference, you can answer a line ringing your station by lifting the handset or pressing the SPEAKER button.

REPEAT LAST NUMBER DIALED

This feature enables you to automatically redial the last number (outside or intercom) called by pressing the RDL button.

To Redial the Last Number

Dialed:

1. Lift the handset.

2. Press any available CO button or INT button.

3. Press the RDL (or # ) button, and proceed with your call.

You will hear dial tone after you press the button.

The last telephone number you dialed will be automatically redialed.

AUTOMATIC BUSY REDIAL

After reaching a busy outside number, you can activate Automatic Busy

Redial (ABR) so that the STRATA DK system will automatically redial that number for you at programmed intervals. ABR is an optional feature enabled in system programming.

2-5

CHAPTER TITLES

FIRST LEVEL

HEADINGS

RESULTS OR

DETAILS

EXPLANATIONS

OR DETAILS OF

THE ACTION TEXT.

Figure

-1

Sample Page

vii

STRATA DK INTRODUCTION

HANDSET

DIALPAD

SPEAKER

MODULAR

HANDSET

CORD

RING VOLUME CONTROL

SPEAKER ON/OFF BUTTON

MICROPHONE BUTTON

ABC

DEF

GHI JKL MNO

4 5 6

PRS TUV WXY

7 8 9

OPER

FLEXIBLE

BUTTONS

MIC CONF/TRNS

SPKR HOLD

RNG VOL

INT

FEATURE AND

FUNCTION LEDS

MICROPHONE

INTERCOM

BUTTON

SPEAKER

VOLUME CONTROL

SLIDING MEMO TRAY

HOLD BUTTON

CONFERENCE/TRANSFER

BUTTON

Figure

-2

20-button Electronic Telephone

viii

Chapter 1

STRATA DK

BUTTON LABEL

ACCNT

ALRM

ABR

ACB

BGM

CFAC

GENERAL INFORMATION

PURPOSE

This chapter is designed to familiarize you with the controls and indicators located on your telephone. Understanding the function of the feature buttons and their associated LEDs will improve your efficiency with the telephone and will help you take advantage of the benefits of your telephone.

FEATURE BUTTONS

Some of the feature buttons described below appear on your telephone.

These buttons provide quick access to features, saving you from having to remember access codes.

Account Code Button (Release 3 and higher)

Press to enter a Voluntary Account Code anytime during a CO line call without interrupting the conversation.

Alarm Reset Button

Press to turn off a telephone alarm connected to a facility alarm mechanism.

All Call Voice Page Button

Press to simultaneously page all of the electronic and digital telephones assigned to the "All Call Page Group" in system programming .

Automatic Busy Redial Button

Press to set up an Automatic Busy Redial after receiving busy tone on a dialed CO line call.

Automatic Callback Button

Press to recall a busy station or station in the Do Not Disturb (DND) mode as soon as that station becomes idle or exits the DND mode. Also used for CO line queuing.

Background Music Button

Press to turn Background Music on or off over your station speaker.

Call Forward-All Call Button

Press to forward all calls to another station or voice mail device.

1-1

STRATA DK

BUTTON LABEL

CFB

CFB/NA

CFNA

CFF

PKUP

PKUP1 or PKUP2

CONF/TRNS

DSS

DND

DRLK

GENERAL INFORMATION

Call Forward-Busy Button (Release 2 and higher)

Press to immediately forward calls to another station or voice mail device when your station is busy or in the Do Not Disturb mode.

Call Forward-Busy/No Answer Button (Release 2 and higher)

Press to forward calls to another station or voice mail device whenever your station is busy or in the Do Not Disturb mode. Also forwards calls when your station is not answered after three rings or 12 seconds.

Call Forward-No Answer Button (Release 2 and higher)

Press to forward calls to another station or voice mail device when your station is not answered after three rings or 12 seconds.

Call Forward-Fixed Button

Press to set call forward to a station or voice mail device assigned in system programming.

Call Pickup Button

Press to initiate a Directed Call Pickup of CO line, intercom, and page calls.

Call Pickup For Tenants Buttons

Press the PKUP1 button to pick up Tenant 1 ringing CO line calls. Press the PKUP2 button to pick up Tenant 2 ringing CO line calls.

Central Office Line Button

Press to access or answer an outside line.

Conference/Transfer Button (Fixed)

Press to set up a Conference or a Transfer.

Direct Station Select Button(s)

Press to ring a particular station assigned in programming. The LED associated with each DSS button provides the status (idle/busy) of the station assigned to the button.

Do Not Disturb Button

Press to activate or deactivate the Do Not Disturb mode at your station.

Door Lock Button

Press to open a door lock mechanism.

1-2

STRATA DK

BUTTON LABEL

HOLD

INT

MSG

MW/FL

MIC

MCO

NT1 or NT2

GENERAL INFORMATION

Hold Button (Fixed)

Press to place internal or outside calls on hold.

Intercom Button

Press to access the intercom.

Message Select Button

Press to Allow system and personal messages to be displayed on the optional 32-character Liquid Crystal Display (LCD).

Message Waiting/Flash Button— MW/FL

Press this button to leave a Message Waiting Indication at another electronic or digital telephone that is not available to answer your call, or press to call back a station or voice mail device that leaves an indication at your station. (The Message Waiting Indication is a flashing MW/FL

LED.)

This button can also be used to disconnect a call and recall dial tone for accessing PBX and Centrex features, and to enter pauses and flashes in

Speed Dial numbers.

Microphone Button (Fixed)

Press to turn the microphone off or on while your telephone is in use.

Microphone Cutoff Button

Press to turn the microphone off or on while your telephone is idle, providing privacy when you receive handsfree intercom calls. Also functional while you are on a call that was initiated by the caller—the

MIC button controls the microphone when you originate calls.

Night Transfer Button

Press to change the system’s CO line ringing pattern for after hours incoming calls.

Night Transfer For Tenants Buttons

Press NT1 to change the tenant 1 CO line ringing pattern for after hours incoming calls. Press NT2 to change the Tenant 2 CO line ringing pattern for after hours incoming calls.

1-3

STRATA DK

BUTTON LABEL

PAU

RDL

RLS

SAVE

SPKR

PAU/L

PRIVACY

PRV RLS

1-4

SDF

GENERAL INFORMATION

Pause Button

Press to enter a one-half-second or two-second pause when storing a

Speed Dial number. The length of the pause is set in system programming.

Pause (Long) Button

Press to enter a 10-second pause when storing a Speed Dial number.

Pooled Line Button

Press to access or answer a CO line from a group of lines appearing under one button.

Privacy Button (Release 3 and higher)

Press to block Privacy Override of a common CO line on your station.

This button does not block Busy or Executive Override.

Privacy Release Button

Press to release privacy on a common CO line at your station so that another station user(s) can enter a conversation on that line.

Redial Button

Press to redial the last telephone number dialed.

Release Button (Release 2 and higher)

Press to disconnect an existing call and make your station idle.

Save Button

After dialing a telephone number, press to "save" the telephone number.

Press the button later to redial the number.

Speaker Button (Fixed)

Press to turn the speaker on or off. If programmed for Auto Preference, the speaker button will also select a CO or intercom line. Also, used to disconnect on-hook speakerphone calls.

Speed Dial Button— SD

Press to speed dial a personally assigned telephone number or a feature access code.

System Speed Dial Button

Press to dial a telephone number or Centrex/PBX feature assigned

(fixed) in system programming.

STRATA DK

BUTTON LABEL

SDS

TONE

GENERAL INFORMATION

Speed Dial Select Button— SDS

Press to access Speed Dial numbers.

Tone Button

Press to change the outgoing dialing of a CO line from dial pulse to tone signaling.

VOLUME CONTROLS

Voice and ring tone volume levels are controlled by separate adjustable slides located at the bottom of the front panel. The right VOL control adjusts the speaker volume for dial tone, station Background Music, Offhook Call Announce, and voice. The left RING control adjusts the ring tone and handsfree voice announcement levels.

LED INDICATIONS

CO button LEDs flash at different rates to indicate the status of CO lines and feature operation.

CO Incoming Call Rate

A CO LED will flash at the following rate when a call is incoming to your station:

■

1/2-second on, 1/2-second off

Consultation Hold Rate

During a consultation and screened transfer to another station, the CO

LED will flash at the following rate at your station:

■

10 impulses per second (IPS)—The LEDs on other stations with this line will be lit steadily.

Exclusive Hold Rate

The CO LED of a line that you place on Exclusive Hold will flash at the following rate at your station:

■

10 IPS—The LEDs on other stations with this line will be lit steadily.

1-5

STRATA DK GENERAL INFORMATION

Hold Recall Rate

The CO LED will flash at the following rate (with matching tones) when a line that you placed on hold recalls your station:

■ 2 IPS for 1 second, 10 IPS for 1 second—The LEDs on other stations with this line will be lit steadily.

Intercom Call Rate

The INT LED at your station will flash at the following rate when another station calls you:

■ 10 IPS for 1 second, 1 second off

In-use Rate

The CO LED will flash at the following rate when you originate a CO line call at your station:

■ 2 seconds on, 1/8-second off, 1/8-second on, 1/8-second off—The

LEDs on other stations with this line will be lit steadily.

On-hold Rate

The CO LED will flash at the following rate at your station when you place a call on hold:

■ 1/8-second on, 1/8-second off—The LEDs on other stations will flash at the following rate: 3/4 second on, 1/4 second off. (If using a Pooled

Line button, the hold indication is only at the station that places the call on hold.)

Busy Station Transfer

When an outside call is transferred to your station when you are busy on another call, the CO LED will flash at the following rate:

■ 10 IPS—The LEDs on other stations with this line will be lit steadily.

1-6

Chapter 2

STRATA DK FEATURE OPERATION

OUTSIDE CALLS

You can make calls to or receive calls from telephones outside of the

STRATA DK system.

To Make an Outgoing Call by

Direct Access:

1. Lift the handset.

2. Press any available CO button.

. . . or . . .

Press any available

PL button.

3. Dial a telephone number.

4. Hang up when the call is completed.

If programmed for Automatic Off-hook Selection, your station will seize a

CO or intercom line when you lift the handset.

After you press the Line button, you will hear CO line dial tone, and the

CO LED will flash at the in-use rate.

You will hear CO dial tone, and the PL LED will flash at the in-use rate.

You will no longer hear dial tone after dialing the first digit of the number, but the LED will continue to flash at the in-use rate.

The LED will turn off.

To Make an Outgoing Call by

Dial Access:

1. Lift the handset.

2. Press the INT button.

3. Dial a CO line access code.

If programmed for Automatic Off-hook Selection, your station will seize a

CO or intercom line when you lift the handset.

After you press the Intercom button, you will hear intercom dial tone, and the INT LED will flash at the in-use rate.

CO line number access codes are 7 0 1 ~ 7 3 6. With some systems, you may have to dial either the general group code (9), Least Cost Routing

(LCR) code (9), or a Line Group code (8 1 ~ 8 9), instead of a CO line number access code.

You will hear CO line dial tone, and the status of the INT LED will continue to flash at the in-use rate. (If you dialed 9 in a system programmed with LCR, you may or may not hear intercom dial tone after dialing the LCR access code, depending on system programming.)

2-1

STRATA DK

4. Dial a telephone number.

FEATURE OPERATION

You will no longer hear dial tone after dialing the first digit of the number, but the LED will continue to flash at the in-use rate.

The LED will turn off.

5. Hang up when the call is completed.

To Receive a Call on a CO Line

Button:

1. When your telephone rings, press the CO button and lift the handset.

2. Hang up when the call is completed.

The status of the CO LED will change from the incoming call rate to the in-use rate when you press the button.

The LED will turn off.

To Receive a Call on a Pooled

Line Button:

1. When your telephone rings, press the PL button or lift the handset.

2. Hang up when the call is completed.

The status of the LED associated with the PL button will change from the incoming call rate to the in-use rate when you press the button or lift the handset.

The LED will turn off.

NOTE: A muted ringing while you are on a call on a PL button indicates that a call is incoming. Answer the incoming call without disconnecting the existing call by one of two ways:

1) Place the call on hold, then answer the incoming call by pressing and holding down the hookswitch for about one second.

2) Transfer the call, then answer the incoming call by pressing and holding down the hookswitch for about one second.

2-2

STRATA DK FEATURE OPERATION

ON-HOOK DIALING

You can dial calls without lifting the handset. You must lift the handset to converse, unless your telephone is a full speakerphone.

OUTSIDE CALLS

You can dial an outside telephone number without lifting the handset.

To Dial an Outside Call While

On-hook:

1. Press any available CO button or PL button.

. . . or . . .

Press the INT button, then dial a CO line or a line group access code.

2. Dial a telephone number.

3. Lift the handset when the called party answers.

4. Hang up when the call is completed.

You will hear CO line dial tone when you press the button, and the CO or

PL LED will flash at the in-use rate.

CO line number access codes are 7 0 1 ~ 7 3 6 and line group codes are

8 1 ~ 8 9. Some systems may require that you dial either the general group code (9) or Least Cost Routing code (9), instead.

You will hear CO line dial tone after you dial the access code, and the

INT LED will flash at the in-use rate.

You will no longer hear dial tone after dialing the first digit of the number, but the LED will continue to flash.

The LED will continue to flash. You do not have to lift the handset, if you have a full speakerphone.

The LED will turn off.

Press the SPEAKER button to disconnect the call if you did not lift the handset.

INTERCOM CALLS

You can dial a station without lifting the handset.

To Dial an Intercom Call While

On-hook:

1. Press the INT button.

You will hear dial tone when you press the button, and the INT LED will flash at the in-use rate.

2-3

STRATA DK

2. Dial a station number.

3. Lift the handset when the called station is answered.

4. Hang up when the call is completed.

FEATURE OPERATION

You will no longer hear dial tone after dialing the first digit of the number, but the LED will continue to flash.

The LED will continue to flash. You do not have to lift the handset if you have a full speakerphone.

The LED will turn off. Press the SPEAKER button to disconnect the call if you did not lift the handset.

GROUP LISTENING

This feature enables you to set your telephone so that you and people near your telephone can hear the distant party, but the distant party will not be able to hear you.

To Activate Group Listening:

1. Establish an off-hook call with a distant party.

2. While holding down the

SPKR button, place the handset on-hook.

3. Release the button.

The SPKR and MIC LEDs will light and the distant party’s voice will be heard over the speaker of the telephone.

To Deactivate Group Listening:

1. Lift the handset.

The SPKR and MIC LEDs will turn off.

The telephone speaker will be deactivated, and the handset will be activated.

2-4

STRATA DK FEATURE OPERATION

AUTOMATIC OFF-HOOK SELECTION

Automatic Off-hook Selection allows you to access a specific line or line group just by lifting the handset or pressing the SPEAKER button. This is an optional feature enabled in system programming.

To Make a Call:

1. Lift the handset or press the

SPKR button.

You will be connected to the option programmed.

If you hear silence, you must press the INT button or a CO or PL button before dialing the telephone number

2. Dial a telephone number, and proceed with your call.

NOTE: If your station is programmed with Ringing Line Preference, you can answer a line ringing your station by lifting the handset or pressing the SPEAKER button.

REPEAT LAST NUMBER DIALED

This feature enables you to automatically redial the last number (outside or intercom) called by pressing the RDL button.

To Redial the Last Number

Dialed:

1. Lift the handset.

2. Press any available CO button or INT button.

3. Press the RDL (or # ) button, and proceed with your call.

You will hear dial tone after you press the button.

The last telephone number you dialed will be automatically redialed.

AUTOMATIC BUSY REDIAL

After reaching a busy outside number, you can activate Automatic Busy

Redial (ABR) so that the STRATA DK system will automatically redial that number for you at programmed intervals. ABR is an optional feature enabled in system programming.

2-5

STRATA DK FEATURE OPERATION

To Activate ABR:

1. While listening to busy tone, press the ABR button.

. . . or . . .

While listening to the busy tone, press the CONF/TRNS button and dial 4 4 .

2. Hang up or press the SPKR button.

3. The system will redial the number.

4. Your telephone willreceive ring tone when ABR dials the number and it is available.

5. Lift the handset or press the

SPKR button and wait for the party to answer.

The ABR LED will flash when you press the button.

You will hear confirmation tone after your press the button.

Hang up if the call was established off-hook; press the SPKR button if the call was established on-hook.

The system will redial every every 30 or 60 seconds (depending on system programming), up to 15 times (See Notes 1 and 2.

The CO—or INT—and SPKR LEDs will flash. The called telephone number will ring.

If you fail to pick up the handset or press the SPKR button within 30 seconds after a connection is made, you will hear a muted ring for another 30 seconds, then the call will disconnect.

To Cancel ABR:

1. Press the ABR button.

. . . or . . .

Press the INT button and dial

4 4 .

NOTES:

ABR will not be attempted while your station is busy, but will continue to time-out.

With each attempt:

■ The CO—or INT—and SPKR LEDs blink when the line is seized.

■ Dial tone is heard via the speaker.

■ The telephone number is redialed.

■ If busy, ABR will reset and try again.

2-6

STRATA DK FEATURE OPERATION

SPEED DIAL

Speed Dial enables you to call a telephone number with a brief access code or an optional feature button. There are two types of Speed Dial numbers. Station Speed Dial numbers are assigned by individual station users to their own station, and can only be dialed at their station. System

Speed Dial numbers can only be assigned from Station 200 (typically the system administrator's telephone), but can be used by other stations.

With Release 4 software, your station will time out to the idle mode if the following storage procedures are not completed within one or three minutes. The time is set in system programming.

STATION SPEED DIAL STORAGE

You can store personal telephone numbers on either Station Speed Dial buttons or access codes. You can call the telephone number by either pressing the button or dialing the acess code.

To Store a Station Speed Dial

Number:

1. Do Not Lift the handset.

2. Press the RDL (or # ) button

3. Press the SD button you wish to store the telephone number on.

. . . or . . .

Press the SDS (or * ) button and enter the code (1 0 ~ 4 9) that you want to store the telephone number in.

The # button can be used if your telephone does not have the RDL button.

SD buttons are assigned in system programming. If your telephone does not have SD buttons, use access codes, instead.

The * button can be used if your telephone does not have the SDS button.

4. Enter the telephone number.

Station Speed Dial number access codes are 1 0 ~ 4 9. Space is provided at the end of this user guide to record Speed Dial codes and their numbers.

You can enter up to 20 digits.See "Speed Dial Number Linking" later in this section for instructions on storing additional digits.

It may be necessary to insert a pause or flash signal in the number. See

"Speed Dial Pause and Flash Storage" later in this section for more details.

2-7

STRATA DK FEATURE OPERATION

5. Press the RDL (or # ) button.

The number will be stored and will be dialed when the SD button is pressed or the Speed Dial access code is dialed.

Repeat this procedure to replace the stored telephone numbers with new ones. To clear a Speed Dial entry, repeat the preceding procedure, skipping Step 4.

SYSTEM SPEED DIAL STORAGE

Only Station 200 (typically the system administrator's phone) can store

System Speed Dial numbers, although they are available to all stations for dialing. System Speed Dial buttons can be assigned to stations in system programming.

To Store a System Speed Dial

Number at Station 200:

1. Do Not Lift the handset.

2. Press the RDL (or # ) button, then the SDS (or * ) button.

3. Enter the access code (6 0 ~

9 9) that you want to store the telephone number in.

4. Enter the telephone number.

5. Press the RDL (or * ) button.

The # button can be used if your telephone does not have the RDL button, and the

SDS button.

* button can be used if your station does not have the

System Speed Dial number access codes are 6 0 ~ 9 9. (Space is provided in the Appendix to record Speed Dial codes and their numbers.)

System Speed Dial buttons associated with the codes are assigned to stations in system programming.

You can store up to 20 digits. See "Speed Dial Number Linking" later in this section for instructions on storing additional digits.

It may be necessary to insert a pause or flash signal in the number. See

"Speed Dial Pause and Flash Storage" later in this section for more details.

The number will be stored and will be dialed when the Speed Dial access code is dialed at a station, or when an SDF button associated with the code is pressed.

Repeat this procedure to replace the stored telephone numbers with new ones. To clear a Speed Dial entry, repeat the preceding procedure, skipping Step 4.

2-8

STRATA DK FEATURE OPERATION

SPEED DIAL PAUSE AND FLASH STORAGE

Some Speed Dial numbers may require that a pause (long or regular) or hookflash be included in the number. For example, you may have to enter a pause at the beginning of a Speed Dial number to allow for dial tone delay.

To Store a Hookflash:

1. Press the MW/FL button.

If your telephone does not have a PAU button but has a MW/FL button, a pause will be entered instead of a hookflash when you try to store a hookflash. To store a hookflash with the MW/FL button, a PAU button must be on your telephone.

If your telephone does not have a PAU button and your STRATA DK system is operating with Release 4 software, a hookflash can be stored by pressing the CONF/TRNS button and dialing 4 5 where the hookflash signal is required in the Speed Dial number string.

To Store a Regular Pause:

1. Press the PAU button This pause—which will be one-and-a-half or three seconds, depending on system programming—can be entered anywhere in the Speed Dial number.

To Store a Long Pause:

1. Press the PAU/L button.

This pause, which is 10 seconds, can be entered anywhere in the Speed

Dial number.

SPEED DIAL NUMBER LINKING

You can link any of your personally assigned Speed Dial Numbers

(1 0 ~ 4 9) to System Speed Dial codes 9 0 ~ 9 9 or to any of the optional buttons associated with these 10 codes. Station 200 (usually the system administrator's station) can be used to link System Speed Dial codes 6 0

~ 8 9 to codes 9 0 ~ 9 9. This allows up to 37 digits to be stored under one System Speed Dial button or code.

The number stored in location 9 0 ~ 9 9 will dial out first, followed by the number linked to 9 0 ~ 99. Typically, a company's special carrier access telephone numbers are stored in locations 9 0 ~ 9 9.

2-9

STRATA DK FEATURE OPERATION

With Release 4 software, your station will time out to the idle mode if the following procedure is not completed within one or three minutes. The time is set in system programming.

To Link a Number:

1. Press the RDL (or # ) button.

2. Press a SD button.

. . . or . . .

Press the SDS (or * ) button and enter a two-digit Speed

Dial access code.

The # button can be used if your telephone does not have a RDL button.

This will be the button on which you will store the linked number.

This will be the code in which you store the linked number. The * can be used if your telephone does not have the SDS button.

button

Station users may enter Station Speed Dial codes (1 0 ~ 4 9). Station

200 can be used to enter System Speed Dial codes 6 0 ~ 8 9.

3. Press the SDS ( * ) button

4. Enter the two-digit code to which the number will be linked ( 9 0 ~ 9 9 ).

Only System Speed Dial Codes 9 0 ~ 9 9 may have numbers linked to them.

5. Enter the number to be linked.

You may enter up to 17 digits. (Space is provided at the end of this user guide to record Speed Dial codes and their numbers.)

6. Press the RDL (or # ) button.

The number will be stored and will be dialed out when the optional linked

System SD button is pressed or the linked System Speed Dial access code is dialed.

CALLING SYSTEM OR STATION SPEED DIAL NUMBERS

You can call Speed Dial numbers with the touch of a button or by dialing a brief access code. Speed Dial buttons are assigned to stations in system programming.

To Call with a Speed Dial button:

1. Access a CO line.

2. Press a SD button.

You can access a CO line by pressing a CO or PL button, or by dialing an access code (7 0 1 ~ 7 3 6 for a line number; 8 1 ~ 8 8 for a line group; and 9 for the general group or Least Cost Routing).

The system will dial the telephone number assigned to the button.

2-10

STRATA DK

3. Hang up when the call is completed.

FEATURE OPERATION

To Call with a Speed Dial

Access Code:

1. Access a CO line.

2. Press the SDS (or * ) button.

3. Dial a 2-digit Speed Dial access code.

You can access a CO line by pressing a CO or PL button, or by dialing an access code (7 0 1 ~ 7 3 6 for a line number; 8 1 ~ 8 8 for a line group; and 9 for the general group or Least Cost Routing).

The * button can be used if your telephone does not have the SDS button.

Station Speed Dial codes are 1 0 ~ 4 9, and System Speed Dial codes are 6 0 ~ 9 9.

The system will automatically dial the telephone number assigned to the dialed code.

CHAIN DIALING SPEED DIAL NUMBERS

You can call two or more Speed Dial numbers sequentially during one call. This enables you, for example, to add additional parties (conference calls) to your conversation with Speed Dialing.

To Chain Dial:

1. Access a CO line.

2. Press the SDS (or * ) button.

3. Dial a Speed Dial access code for the first telephone number to be dialed.

4. Repeat Steps 2 and 3 to dial another telephone number.

You can access a CO line by pressing a CO or PL button, or by dialing an access code (7 0 1 ~ 7 3 6 for a line number; 8 1 ~ 8 8 for a line group; and 9 for the general group or Least Cost Routing).

The * button can be used if your telephone does not have the SDS button.

Station Speed Dial codes are 1 0 ~ 4 9, and System Speed Dial codes are 6 0 ~ 9 9.

2-11

STRATA DK

5. Hang up when the call is completed.

FEATURE OPERATION

SAVED NUMBER REDIAL

This feature enables you to store a dialed telephone or station number, then redial that number with the touch of a button. Your telephone must be assigned with the SAVE button in system programming.

To Save a Telephone Number:

1. While on a call that you dialed, press the SAVE button.

To Call a Saved Telephone

Number:

1. Access a CO line.

2. Press the SAVE button.

You can press the button anytime after you have dialed the final digit of the telephone number, but you must do it before you hang up or disconnect the call.

You can access a CO line by pressing a CO or PL button, or by dialing an access code (7 0 1 ~ 7 3 6 for a line number; 8 1 ~ 8 8 for a line group; and 9 for the general group or Least Cost Routing).

The system will automatically dial the "saved" number.

DTMF TONE DIALING WITH

AND #

You may have to send * and # Dual-tone Multi-frequency (DTMF) tones to some devices or services, such as a voice mail device or computer output service. If you do not have both the SDS and RDL buttons on your telephone, you must first dial an access code to enable these tones to be transmitted. DTMF tones are automatically enabled on stations with both the SDS and RDL buttons.

To Output * and # DTMF Tones

1. While on an outside call, press the * button, then the

# button.

You will now be able to output * and # DTMF tones, as well as digits

0 ~ 9.

This feature disables the Speed Dial feature. Speed Dial will be restored when you complete the call or place it on hold.

2-12

STRATA DK FEATURE OPERATION

TONE/PULSE DIALING

With some older Central Offices, you may have to make calls using rotary dial pulses on CO lines. To access remote equipment (such an an answering machine) requiring Dual-tone Multi-frequency (DTMF) tones while on these lines, you must set your phone for tone dialing after you have dialed the telephone number. Your telephone must have a TONE button assigned in system programming to access this feature.

To Change to Tone Dialing:

1. Dial a telephone number on a

CO line programmed for rotary dial pulses.

2. While the call is in progress, press the TONE button.

Although the CO line is programmed for rotary dial pulses, access the

CO line and dial the telephone number like any other call described in this user guide.

After you press the button, the TONE LED will light steady red, and you will be able to send DTMF tones with your dialpad.

If the LED is off, tone dialing is not selected and you will not be able to send DTMF tones.

NOTE: When originating or receiving a new CO line call, the system will automatically place the line in the dial pulse mode.

PRIVACY OVERRIDE

This optional feature allows you to enter an established call on a private common CO line button. Up to two station users may enter an existing

CO line-to-station call (allowing up to three stations to be connected to a

CO line). To access this feature, your station must be assigned with

Privacy Override in system programming, or the station that is already connected to the CO line must be in the Privacy Release mode.

To Override a Call:

1. Press a busy CO button.

You will now be connected to the CO line, and will be able to participate in the conversation.

An optional tone signal may be heard by the connected parties before you enter the conversation.

2-13

STRATA DK FEATURE OPERATION

NOTE:

Private CO lines deny station users access to busy common CO line buttons. Besides Privacy Override, Privacy Release also enables station users to enter a call on a private CO line button.

PRIVACY BUTTON (Release 3 and higher)

This option blocks a user at a station programmed with Privacy Override from entering a CO line conversation. Your station must be assigned with the PRIVACY button in system programming to activate this feature, which will not block Busy Override or Executive Override. Busy and

Executive Override are described later in this guide.

To Make All CO Lines on Your

Station Private:

1. Press the PRIVACY button.

After you press the button, the PRIVACY LED will light steady, and station users will not be able to enter CO line calls on your station with

Privacy Override.

To Cancel Privacy:

1. Press the PRIVACY button again.

The PRIVACY LED will turn off, and station users will now be able to enter CO line calls on your station with Privacy Override.

PRIVACY RELEASE

If you press the optional PRV RLS button, any other station user can enter your call on a private common CO line button just by pressing the

CO button on his or her telephone. Your station must be assigned with the PRV RLS button in system programming to activate this feature.

To Activate Privacy Release:

1. While on an outside call, press the PRV RLS button.

After you press the button, the PRV RLS LED will light steady, and station users will be able to enter your calls by pressing a common CO line button.

2-14

STRATA DK

To Deactivate Privacy Release while on a Call:

1. Press the PRV RLS button again.

FEATURE OPERATION

The PRV RLS LED will turn off, and station users without Privacy

Override will not be able to enter your calls by pressing a common CO line button.

If you do not deactivate Privacy Release while on the call, it will turn off when you hang up.

NOTE: Private CO lines deny station users access to busy common CO line buttons.

INTERCOM CALLS

You can make calls to and receive calls from other stations in the

STRATA DK system

To Make an Intercom Call:

1. Lift the handset.

2. Press the INT button.

3. Dial the desired station number.

You will hear silence after you lift the handset, unless your station has been programmed for Automatic Off-hook Selection.

Skip Step 1 if Automatic Off-hook Selection provides CO line dial tone when you lift the handset. Skep Step 2 if the feature provides intercom dial tone when you lift the handset.

After you press the button, you will hear intercom dial tone, and the INT

LED will flash at the in-use rate.

If the called station is idle:

■

If you hear a single ring ton with Voice First Signaling, you should make a voice announcement. (You can dial 1 to change to Tone

Signaling.)

■

If you hear ring tones with Tone Signaling, wait to see if the call is answered. (You can dial 1 to change to Voice First Signaling.)

2-15

STRATA DK FEATURE OPERATION

If you receive busy tone:

■ Dial 4 to set Automatic Call Back (ACB).

■ Dial 2 or 2 1 to override or Off-hook Call Announce.

■ Dial 3 to enter the station's conversation (system programmable option)

If you dial a busy or unanswered station and want to leave a Message

Waiting Indication, dial 7.

4. Hang up when the call is completed.

To Receive an Intercom Call

(Voice First Signaling):

1. You will hear a single long tone, followed by the caller’s voice.

2. Lift the handset.

3. Hang up when the call is completed.

The INT LED will flash at the incoming call rate.

If the call were made with Tone signaling instead of Voice First Signaling, your phone would ring.

The INT LED will flash at the in-use rate after you lift the handset.

The INT LED will turn off.

HANDSFREE ANSWERBACK

You can answer intercom calls without lifting the handset.

To Receive a Handsfree

Intercom Call:

1. You will hear a single long tone, followed by the caller’s voice.

2. Don't lift the handset; speak at a normal voice level towards the telephone.

The INT LED will flash at the incoming call rate.

The MIC LED will light steady, indicating your microphone is active, and the SPKR LED will flash.

To control the volume level of the caller's voice, slide the Ring volume control to the desired setting.

NOTE: The Intercom button must be pressed (or the handset must be taken off-hook) before placing an intercom call on hold.

2-16

STRATA DK FEATURE OPERATION

MICROPHONE CUT-OFF

You can prevent Handsfree Answer Back calls to your telephone by turning off the microphone while in the idle state. Microphone Cut-off prevents callers from monitoring the sounds near your telephone. Your station must be assigned with the Microphn Cut-off button in system programming to activate this feature.

To Cut Off the Microphone:

1. Press the MCO button.

After you press the button, the MCO LED will light steady, and the microphone and SPKR LED will not turn on when your telephone is called.

To Turn the Microphone On:

1. Press the MCO button again.

The MCO LED will turn off.

OFF-HOOK CALL ANNOUNCE (OCA)

This feature allows you to call and speak through the speaker of an offhook, busy digital or electronic telephone. The called telephone must be equipped for OCA capability.

To Make an OCA Call with Voice

First Signaling:

1. Lift the handset.

2. Call the desired station.

You will hear a warning tone and you will be able to talk to the called station if your station is programmed for automatic OCA operation.

If your station is not programmed for automatic operation, you will hear busy tone and must dial 2 to speak to the called station.

To Make an OCA Call with Tone

Signaling:

1. Lift the handset.

2. Call the desired station.

2-17

STRATA DK FEATURE OPERATION

3. When you receive busy tone, dial 2 1 .

Speak to the called station after dialing 2 1.

FORCED DISCONNECT

You can disconnect an OCA call made to your station.

To Force a Disconnect:

1. Press the SPKR button.

The OCA call will be disconnected after you press the button.

NOTES:

Stations in the Do Not Disturb mode cannot receive OCA calls.

The MIC and MCO buttons can prevent an OCA caller from listening to your conversation.

Adjust the volume level of the OCA caller's voice with the Vol slide control on the bottom of the front panel of your telephone.

CALL TRANSFER WITH CAMP-ON

You can transfer calls to busy stations with this feature.

NOTE: You cannot transfer (or camp-on) to stations that are in the Do

Not Disturb (DND) mode.

To Transfer a Call (Voice First

Signaling):

1. While on an outside call, press the CONF/TRNS button.

2. Dial the station number to which the call will be transferred.

3. Announce the call if the called station is idle, then hang up.

After you press the button, the CO LED will flash at the conference rate, and the INT LED will flash at the in-use rate.

You will hear a single ring tone. (If the call was made with Tone Signaling instead of Voice First Signaling, you would hear ringback tone.)

The INT LED will turn off, the CO LED will begin to flash at the on-hold rate, and the CO line will ring the called station. (See the Note that follows.)

The CO LED will become steady when the called station connects with the transferred call.

2-18

STRATA DK FEATURE OPERATION

If the called station user fails to answer the call, you will receive a recall ring after a time set in system programming.

. . . or . . .

Hang up if the called station is busy.

The INT LED will turn off, and the CO LED will begin to flash at the onhold rate. The CO line will camp on to the called station (see the Note that follows), and the called station will receive a warning tone.

The CO LED will become steady when the called station connects with the transferred call.

If the called station user fails to answer within a predetermined time, the call will recall you and camp-on will be cancelled . Inform the caller of the situation, and repeat the procedure if necessary.

NOTE: You may reconnect to a transferred line (anytime before it is answered) by pressing the appropriate CO button, or by dialing INT 4 2 if the CO button does not appear on your telephone.

ANSWERING A TRANSFERRED CALL

You can answer a call that is transferred to your station, whether you are idle or busy on another call.

To Answer While Idle (Voice

First Signaling):

1. You will hear a single long tone, followed by an announcement.

2. Acknowledge the announcement.

3. When the transferring station hangs up, you will hear a ringing tone.

The INT LED will flash at the incoming call rate.

The CO LED will flash at the incoming call rate.

2-19

STRATA DK FEATURE OPERATION

4. Press the appropriate button.

CO After you press the button, the CO LED will flash at the in-use rate, and you will be connected to the call.

NOTE: If your telephone has been assigned with Ringing Line

Preference in system programming, you may press the SPKR button or lift the handset instead of pressing the CO button.

To Answer While Idle (Tone

Signaling):

1. You will hear intercom ringing.

2. Lift the handset or press the

SPKR button.

3. Speak to the transferring station.

4. You will be connected to the outside call when the transferring station hangs up.

The INT LED will flash at the incoming call rate.

After you press the button, the INT LED will flash at the in-use rate.

The INT LED will turn off, and the CO LED will flash at the in-use rate when the transferring station user hangs up.

To Answer While Busy:

1. You will hear a one-second warning tone.

The outside call is camped on to your station, and the CO LED will flash at the on-hold rate.

2. You have several choices:

Press the

. . . or . . .

CO button.

Hang up.

The existing call will be terminated. The camped-on line will ring your telephone, and the CO LED will flash at the incoming call rate.

. . .then . . .

Press the CO button or lift the handset.

After you press the button, you will be connected to the transferred call, and the CO LED will flash at the in-use rate.

. . . or . . .

After you press the button, the existing call will be terminated (or placed on hold if your station has been programmed with the Release 4 Auto

Hold feature), and you will be connected to the transferred call. The CO

LED will flash at the in-use rate.

2-20

STRATA DK FEATURE OPERATION

Press the HOLD button

(if conversing on a CO line).

. . . then . . .

Press the CO button

The existing call will be put on hold. The camped-on line will ring your station, and the CO LED wll flash at the incoming call rate.

You will be connected to the transferred call, and the CO LED will flash at the in-use rate.

CONFERENCE CALLS

This feature enables you to add other parties to an existing call.

CONFERENCE WITH STATIONS AND CO LINES

Conference Calls can be up to two stations and two CO lines total, or up to three stations and one CO line total.

To Add a Second CO Line:

1. While on a CO line call, press the CONF/TRNS button.

2. Access a second CO line and dial the next telephone number.

3. Press the CONF/TRNS button after the party answers.

After you press the button, you will hear intercom dial tone.

The CO LED will flash at the conference rate if the call is on a CO button; and the INT LED will flash at the in-use rate.

You can access a CO line by pressing a CO or PL button, or by dialing an access code (7 0 1 ~ 7 3 6 for a line number; 8 1 ~ 8 8 for a line group; and 9 for the general group or Least Cost Routing).

If you receive a busy tone or no answer, return to the original connection by pressing the CO button or hang up, and the original connection will recall you immediately.

Both CO LEDs will flash at the in-use rate.

All parties will be conferenced. You may add one more station to a two-

CO line conference.

2-21

STRATA DK FEATURE OPERATION

To Add a Station to a CO Line

Call:

1. Press the button.

CONF/TRNS

2. Dial the number of the station to be added.

3. Press the CONF/TRNS button after the party answers.

After you press the button, you will hear intercom dial tone.

The INT LED will flash at the in-use rate; and the CO LED will flash at the conference rate if the CO line call was established on a CO button.

If you receive a busy tone or no answer, return to the original connection by pressing the CONF/TRNS button.

All parties will be conferenced.

The CO LED will flash at the in-use rate if the CO line call was established on a CO button.

The new station will not be conferenced, unless its user lifts the handset or presses the INT button to answer.

Up to three stations (including your own) may conference with one CO line.

4. Repeat to add another party.

5. Hang up when the conference call is completed.

CONFERENCE WITH STATIONS ONLY

As many as four stations may be conferenced on one intercom line.

To Conference with Stations

Only:

1. While on a station call, press the CONF/TRNS button.

2. Dial the third station’s number.

3. Press the CONF/TRNS button after the party answers.

After you press the button, you will hear intercom dial tone, and the INT

LED will flash at the conference rate.

The INT LED will flash at the in-use rate, and all par ties will be conferenced.

2-22

STRATA DK FEATURE OPERATION

4. To add the fourth station, repeat Steps 1 ~ 3.

CALL FORWARD

You can set your station with a variety of Call Forward modes.

NOTE: If Call Forward is set:

■

CO lines that ring your station only will forward—CO lines that ring more than one station will not forward.

■

CO line calls transferred to your station will forward.

■

Intercom calls will forward (handsfree calls may or may not).

■

Call Forward has priority over the Station Hunt feature.

■

Call Forward must be set before the call is received.

■

Call Forward can be set with the touch of one button with Release 4.

See User Programmable Feature Buttons later in this chapter.

CALL FORWARD-ALL CALLS

If your station is idle or busy and has this feature activated, all calls to it will forward immediately. Your station will not ring.

To Set Call Forward-All Calls:

1. Press the CFAC button.

. . . or . . .

Press the INT button, then dial 6 0 1 .

2. Enter the station number to which calls will forward.

3. Press the CFAC button or the

SPKR button.

The CFAC LED will flash.

You will hear confirmation tone.

You will hear confirmation tone if 6 0 1 was dialed in Step 1.

The CFAC LED will become steady, and calls will forward to the stored station number.

To Cancel:

1. Press the CFAC button.

. . . or . . .

Press the INT button, dial 6

0 1 , then press the SPKR button.

The CFAC LED will turn off.

You will hear confirmation tone.

2-23

STRATA DK FEATURE OPERATION

CALL FORWARD-BUSY (Release 2 and higher)

Calls to your telephone while you are busy on another call or in the Do

Not Disturb mode will forward immediately if this feature is set. Calls will ring as normal if your telephone is idle.

To Set Call Forward-Busy:

1. Press the CFB button.

. . . or . . .

Press the INT button, then dial 6 0 2 .

2. Enter the station number to which calls will forward.

3. Press the CFB button or the

SPKR button.

The CFB LED will flash.

You will hear confirmation tone.

You will hear confirmation tone if 6 0 2 was dialed in Step 1.

The CFB LED will become steady, and calls will forward to the stored station number.

To Cancel:

1. Press the CFB button

. . . or . . .

Press the INT button, dial 6

0 2 , then press the SPKR button.

The CFB LED will turn off.

You will hear confirmation tone.

CALL FORWARD-NO ANSWER (Release 2 and higher)

All calls to your station when set with this feature will forward to a selected station if you fail to answer within 12 seconds or three rings, whichever occurs first.

NOTE: Your station can be assigned in Release 4 system programming not to Call Forward-No Answer when receiving Voice First (handsfree) calls. Callers can activate Call Forward-No Answer when this feature is set at your station by dialing 1 anytime during their voice announcement.

To Set Call Forward-No Answer:

1. Press the CFNA button.

. . . or . . .

2-24

The CFNA LED will flash.

STRATA DK FEATURE OPERATION

Press the INT button, then dial 6 0 3 .

2. Enter the station number to which calls will forward.

You will hear confirmation tone.

You will hear confirmation tone if 6 0 3 was dialed in Step 1.

3. Press the CFNA button,or the

SPKR button.

The CFNA LED will become steady, and calls will forward to the stored station number.

To Cancel:

1. Press the CFNA button

. . . or . . .

Press the INT button, dial 6

0 3 , then press the SPKR button.

The CFNA LED will turn off.

You will hear confirmation tone.

CALL FORWARD-BUSY/NO ANSWER (Release 2 and higher)

All calls to your station set with this feature will forward immediately to a selected station whenever you are busy on another call or in the Do Not

Disturb mode. Calls will also forward if you do not answer the call within

12 seconds or three rings, whichever occurs first.

NOTE: Your station can be assigned in system programming not to Call

Forward-No Answer when receiving Voice First (handsfree) calls. Callers can activate Call Forward-No Answer when this feature is set at your station by dialing 1 anytime during their voice announcement.

To Set Call Forward-Busy/No

Answer:

1. Press the CFB/NA button.

. . . or . . .

Press the INT button, then dial 6 0 4 .

2. Enter the station number to which calls will forward.

3. Press the CFB/NA button or the SPKR button.

The CFB/NA LED will flash.

You will hear confirmation tone.

You will hear confirmation tone if 6 0 4 was dialed in Step 1.

The CFB/NA LED will become steady, and calls will forward to the stored station number.

2-25

STRATA DK FEATURE OPERATION

To Cancel:

1. Press the CFB/NA button.

. . . or . . .

Press the INT button, dial 6

0 4 , then press the SPKR button.

The CFB/NA LED will turn off.

You will hear confirmation tone.

CALL FORWARD-FIXED

All intercom and CO line calls to your station will forward immediately to a station set in system programming if you activate this feature. Your station must be assigned with the CFF button in system programming to activate this feature.

To Activate Call Forward-Fixed:

1. Press the CFF button.

After you press this button, CFF LED will light steady, and all calls will forward to a station or voice mail device set in system programming.

To Cancel:

1. Press the CFF button.

The CFF LED will turn off.

CALL HOLD

You can place intercom and CO line calls on hold.

To Hold a Call that Appears on a

CO or Intercom Button:

1. While on a CO line or intercom call, press the

HOLD button.

After you press the button, the CO or INT LED will flash at the on-hold rate.

You will hear a recall tone if you do not retrieve the held call before a time set in system programming.

The call may be released automatically if the held party hangs up and the CO provides a hold-release signal.

To place a Handsfree Answerback call on hold you must first lift the handset or press the Intercom button.

2-26

STRATA DK FEATURE OPERATION

NOTE: If your station is programmed with the Release 4 feature Auto

Hold, an existing call will automatically be placed on hold if your answer or make another call. You will not have to press the HOLD button. (See

Auto Hold later in this chapter.)

To Retrieve the Call:

1. Press the CO button or the

INT button on hold.

The CO or INT LED will flash at the In-use rate.

CALL PARK

When your telephone does not have a feature button for a particular CO line, you can dial an access code to place a call on that line on hold

(park) so that you can place a second call. You can also park an intercom call.

To Park a Call and Place another

Call:

1. While on a call, press the

CONF/TRNS button, then dial 4 1 .

2. Press the INT button or a CO button; then dial the desired number.

3. Hang up or press the SPKR button when the call is completed.

The call will be be placed on hold/park after you dial 4 1. You can only have one call parked at your station.

The CO or INT LED will flash at the in-use rate.

The CO or INTLED will turn off.

2-27

STRATA DK

To Retrieve the Parked Call on

Your Telephone:

1. Press the INT button, then dial 4 2 .

FEATURE OPERATION

You will be reconnected to the call.

NOTE:When a CO line is placed on hold or parked, it may be picked up from any station:

■ By pressing a common CO line button.

■ Pressing the INT button and dialing 5 + the holding station’s intercom number.

■ Pressing the INT button and dialing 5 7 + the holding CO line’s number—0 1 ~ 3 6.

EXCLUSIVE HOLD

Exclusive Hold allows you to place a call on hold so that only you or somebody using a Call Pickup code at another station can retrieve it.

To Place a Call on Exclusive

Hold:

1. While on an outside call, press the HOLD button twice.

After you press the button the second time, the CO LED will flash at the exclusive hold rate.

To Retrieve the Call:

1. Press the CO button that is on Exclusive Hold.

Another station user can pick up the call by dialing 5 plus your station number, or by dialing 5 7 plus the CO line number (0 1 ~ 3 6) that the call is held on.

CALL PICKUP

You can pick up a call that is ringing another station, a call placed on hold at another station, and other types of calls.

2-28

STRATA DK FEATURE OPERATION

To Pick Up a Ringing CO Line in a Tenant System (Tenants 1 and

2):

1. Press the PKUP1 or

PKUP2 button.

. . . or . . .

Press the INT button and dial

5 9 .

After you press the button, you will be connected to an incoming CO line call.

You will be connected to an incoming CO line call after you dial 5 9.

DIRECTED CALL PICKUP

Directed Call Pickup provides you with several ways to pick up calls ringing in, or calls held at other stations. You can also pick up an intercom page and an external page with Directed Call Pickup.

To Use Directed Pickup:

1. Press the PKUP button If you do not have a Directed Call Pickup button, press the INT button, then dial 5, instead.

You will be connected to the call ringing in or the held call.

2. Station—Dial a Station number to pick up a call that is ringing in at or held at the station.

. . . or . . .

Intercom Page—Dial 3 0 .

. . . or . . .

External Page—Dial 3 5 .

. . . or . . .

CO line on hold—Dial the CO line access code

(7 0 1 ~ 7 3 6).

. . . or . . .

Any ringing CO line—Dial 9 .

. . . or . . .

Ringing Door Phone—Dial

3 0 .

You will be connected to the station from which the page is coming from.

You will be connected to the CO line that is on hold.

You will be connected to the CO line that is ringing in.

You will be connected to the door phone.

2-29

STRATA DK FEATURE OPERATION

DO NOT DISTURB

Intercom calls will not ring your station, calls can 't be transferred to it, and Off-hook Call Announce calls to it will be denied if your station is in the Do Not Disturb mode. Incoming CO line calls, though, will mute ring at your station. You can continue to make calls as normal while in the Do

Not Disturb mode.

To Activate Do Not Disturb:

1. Press the DND button.

After you press the button, the DND LED will light steady, and the Do Not

Disturb mode will be activated.

To Deactivate Do Not Disturb:

1. Press the DND button.

The DND LED will turn off, and the Do Not Disturb mode will be deactivated.

NOTE: Calls will forward from your station if it set for Call Forward-Busy or Call Forward-Busy/No Answer while in the Do Not Disturb mode.

AUTOMATIC CALLBACK

After reaching a busy or Do Not Disturb station, you may set Automatic

Callback to have the system call you back when the called station becomes available.

To Set Automatic Callback

(Voice First Signaling):

1. After reaching a busy station, press the ACB button or dial

4 .

2. Place the handset on-hook.

After you press the button or dial 4, the busy tone will stop. You will hear dial tone for two seconds, then the busy tone will resume.

You may make other calls while waiting for the called station to become available.

The INT LED will flash at the incoming call rate.

3. Your telephone will ring at a fast rate when the called station becomes idle:

2-30

STRATA DK FEATURE OPERATION

4. Answer the call immediately.

Answer within three rings to prevent the callback from being cancelled.

You will hear a single tone, and the INT LED will flash at the in-use rate.

The called station will have voice announce activated. (With Tone

Signaling, you would hear ringback tone and the called station would ring.)

If you hear a busy tone after answering a callback, the called party has already received or originated another call. Your request is not cancelled.

5. Proceed to voice announce and converse.

CO LINE QUEUING WITH AUTOMATIC CALLBACK

Automatic Callback enables you to be placed in a waiting queue for an available CO line after attempting access to a line group in which all lines are busy. The system will call you back when a line becomes available.

To Set CO Line Queuing:

1. If all outgoing lines are busy, you will hear busy tone after dialing a line access code.

2. Press the ACB button or dial

4 .

3. Place the handset on-hook.

4. Your telephone will ring at a fast rate when a CO line becomes idle.

5. Lift the handset immediately.

After you press the button or dial 4, the busy tone will stop, you will hear dial tone for two seconds, then busy tone will resume.

You may make other calls while waiting for a line to become available.

The CO LED will flash at the incoming call rate.

Answer within three rings to prevent the callback from being cancelled.

You will hear CO dial tone. (If you hear a busy tone, the line has already been seized or has received an incoming call. Your request is not cancelled. You will be called again the next time a line becomes idle.)

The CO LED will flash at the In-use rate.

2-31

STRATA DK

6. Dial a telephone number.

7. Hang up when the call is completed.

To Cancel Automatic Callback

(CO Line Queuing):

1. Press the ACB button.

. . . or . . .

Press the INT button, then dial 4 3 .

FEATURE OPERATION

If the original call was made using Least Cost Routing (LCR), the telephone number would have been automatically dialed in Step 4.

Automatic Callback will be cancelled.

ACCOUNT CODE CALLS

Entered before or after a call, Account Codes can be used for a variety of reasons including billing, tracking, and line restriction applications.

Account Codes are recorded by the system and can, along with the details of the calls with which they are associated, be printed out on a

Station Message Detail Recording (SMDR) report.

FORCED ACCOUNT CODES (Release 3 and higher)

Some applications may require that you enter an Account Code, called a

Forced Account Code, before dialing a telephone number.

To Record a Forced Account

Code:

1. Access a CO line.

You can access a CO line by pressing a CO or PL button, or by dialing an access code (7 0 1 ~ 7 3 6 for a line number; 8 1 ~ 8 8 for a line group; and 9 for the general group or Least Cost Routing).

You will hear dial tone after accessing a line. (If you dialed with Least

Cost Routing you will not hear dial tone.)

2-32

STRATA DK

2. Enter the Forced Account

Code.

3. Dial a telephone number.

FEATURE OPERATION

Dial tone stops after you dial the first digit. You will hear dial tone after you press the last digit of a valid account code, or busy tone if you dial an invalid code. (If you dialed with Least Cost Routing, you will not hear dial tone.)

Any digits dialed after the account code will be treated as part of a telephone number.

EMERGENCY OVERRIDE OF FORCED ACCOUNT CODES (Release 3 and Higher)

You can bypass Forced Account Code requirements with three emergency numbers, including 911. See your system administrator for these numbers:

1) 911 2) _________ 3) _________

VOLUNTARY ACCOUNT CODES

Voluntary Account Codes are optional and can be entered after seizing a

CO line or during a call.

To Record a Voluntary Account

Code With:

1. With Release 3 and higher:

Anytime after seizing a CO line or during a call, press the

ACCNT button.

. . . or . . .

With Release 3 and higher:

Press the SDS (or * ) button and dial 5 0 .

. . . or . . .

With Releases 1 and 2:

Press the CONF/TRNS button and dial 4 6 .

Your conversation will not be interrupted.

Your conversation will not be interrupted. If your station does not have a

Speed Dial button, press * 5 0.

Your conversation will be interrupted.

2-33

STRATA DK FEATURE OPERATION

2. Enter the Account Code.

If the code is valid, you will hear a confirmation tone (one-half second duration). If the code is invalid, you will hear two short confirmation tones. Repeat Steps 1 and 2 to dial another account code; the last code entered will be recorded.

If your station is programmed not to verify Account Codes, you will not hear a confirmation tone. (The outside party will not be able to hear tones when the Account Code digits are being entered or any confirmation tones.)

Any digits dialed after the code has been entered will be treated as part of the outside telephone number.

NOTE: Voluntary Account Codes can be set in system programming to change the Toll Restriction classification of your station. See your system administrator for more information.

VERIFIED ACCOUNT CODES (Release 3 and higher)

The length of Account Codes (Forced or Voluntary) is set in system programming. If Account Codes are Nonverified, any sequence of digits entered for a Forced or Voluntary Code will be valid, as long as the length matches the length set in system programming. Specific digits, though, must be entered with Verified Account Codes. Verified Account

Codes are established in system programming or by designated stations

To Add, Delete, or Change

Verified Account Codes From a

Designated Station:

1. Press the INT button, then dial the Verified Account Code

Change Access Code.

You will hear confirmation tone.

For security reasons the Account Code Change Access Code is not provided in this guide. Contact your system administrator for this access code.

2. Dial the Verified Account

Code Number (0 0 0 ~ 2 9 9).

3. Enter the Verified Account

Code.

Verified Account Codes can be one to 15 digits.

2-34

STRATA DK FEATURE OPERATION

4. Press the RDL (or # ) button.

5. Repeat Steps 1 ~ 4 to enter more Verified Account Codes.

You will hear confirmation tone, and the code will be stored in memory.

The newly entered code will overwrite any Verfied Account Code that may have previously been stored with the Verified Account Code Number

(0 0 0 ~ 2 9 9).

You can use press the # button in Step 4 if your station does not have a

RDL button.

To erase an Account Code from memory, repeat the procedure, skipping

Step 3.

PAGING

Station users can make page announcements to telephones and external speakers.

To Page:

1. Lift the handset.

2. Press the INT button and dial one of the following access codes:

3 0 = All Call This code will allow a page to the speakers of telephones assigned to the

"All Call Group" in system programming.

. . . or . . .

3 1 = Station Group A

. . . or . . .

This code will allow a page to telephones assigned to station page group

A in system programming.

3 2 = Station Group B This code will allow a page to telephones assigned to station page group

B in system programming.

. . . or . . .

3 3 = Station Group C This code will allow a page to telephones assigned to station page group

C in system programming.

. . . or . . .

3 4 = Station Group D This code will allow a page to telephones assigned to station page group

D in system programming.

. . . or . . .

3 9 = All Call This code will allow a page to the speakers of telephones assigned to the

"All Call Group" in system programming.The page may also be sent to external speakers (all zones), if enabled in system programming.

2-35

STRATA DK FEATURE OPERATION

. . . or . . .

3 5 ~ 3 8 = External Page

Zones (A ~ D)

3. Make your announcement in a normal voice level and repeat it.

4. Hang up when you complete your announcement.

Dial 35 for Zone A, 36 for Zone B, 37 for Zone C, and 38 for Zone D.

NOTE: Each of the page access codes can be stored on a Speed Dial button with Release 4. See User Programmable Feature Buttons later in this chapter.

ALL CALL PAGE BUTTON

You can make an All Call Page to digital and electronic telephones assigned to the "All Call Page group" with the touch of an All Call Page

(AC) button assigned in system programming. Stations are assigned to the "All Call Page Group" in system programming.

To Make an All Call Page:

1. Lift the handset.

2. Press the AC button.

3. Make your announcement in a normal voice level and repeat it.

4. Hang up when you finish your announcement.

The AC button does not access external page speakers.

DOOR PHONE

Door phones can be used to call digital and electronic telephones selected in system programming. You can call a door phone and monitor the area surrounding the door phone.

2-36

STRATA DK FEATURE OPERATION

To Answer a Door Phone Call:

1. You will hear a distinctive ringing tone.

2. Lift the handset.

Your phone will ring five times or only once, depending on system programming.

After you lift the handset, the INT LED will flash at the in-use rate and you will be connected to the door phone.

3. Hang up when the call is completed.

NOTE: To pick up door phone calls that are ringing other stations but not yours, press the INT button and dial 5 3 0.

To Call/Monitor a Door Phone:

1. Lift the handset.

2. Press the INT button.

3. Dial the intercom number for the desired door location.

You will hear intercom dial tone, and the INT LED will flash at the in-use rate.

151 Location ____________________

152 Location ____________________

153 Location ____________________

154 Location ____________________

155 Location ____________________

156 Location ____________________

157 Location ____________________

158 Location ____________________

159 Location ____________________

161 Location ____________________

162 Location ____________________

163 Location ____________________

4. Hang up when the call is completed or when you are finished monitoring.

NOTE: Door phone numbers can be stored on Speed Dial buttons with

Release 4. See User Programmable Feature Buttons later in this chapter.

2-37

STRATA DK

To Make a Call from a Door

Phone:

1. Press the button and then release it.

2. When answered, speak at a normal voice level in the direction of the door phone.

FEATURE OPERATION

You will hear a distinctive ringing tone (five times or once, depending on system programming).

HANDSFREE MONITORING

Calls placed on hold by an outside party may be monitored handsfree.

This feature frees you from having to hold the handset to your ear until the outside party returns to the call, enabling you to take care of other tasks in the meantime.

To Use Handsfree Monitoring:

1. While on a call, press and hold down the SPKR button.

2. Place the handset on-hook.

3. Release the SPKR button.

The SPKR LED will light.

The SPKR LED will remain on.

The SPKR LED will remain on, and sounds from the distant party are heard over your telephone speaker.

4. Lift the handset when the distant party returns.

ALARM RESET

Your STRATA DK system may be connected to a facility alarm system. All telephones in the system will produce a startling tone whenever this alarm is activated. Station users with an ALARM button can reset the alarm by pressing the button.

2-38

STRATA DK FEATURE OPERATION

To Turn On BGM over External

Speakers from Station 200:

1. Press the INT button, dial 4

9 1 , then press the SPKR button.

BACKGROUND MUSIC (BGM) OVER

TELEPHONE SPEAKERS

You may listen to optional Background Music over your station speaker.

To Listen to BGM on Your

Telephone Speaker:

1. Press the BGM button.

. . . or . . .

Press the INT button, dial 4

8 1 , then press the SPKR button.

You will hear BGM over your telephone speaker.

NOTE: You can adjust the BGM volume level with the Vol control on the bottom of the front panel.

To Cancel BGM on Your

Telephone Speaker:

1. Press the BGM button.

. . . or . . .

Press the INT button, dial 4

8 0 , then press the SPKR button.

The BGM will quit playing over your telephone speaker.

BACKGROUND MUSIC (BGM) OVER EXTERNAL

SPEAKERS

Station 200 (typically the system administrator's station) only can turn on and off BGM over external speakers. Other stations can only control

BGM being played over their speakers.

BGM will play over the external speakers after the SPKR button is pressed.

2-39

STRATA DK FEATURE OPERATION

To Turn Off BGM over External

Speakers from Station 200:

1. Press the INT button, dial 4

9 0 , then press the SPKR button.

BGM will quit playing over the external speakers after pressing the SPKR button.

DIRECT INWARD SYSTEM ACCESS (DISA)

(Release 2 and higher)

Outside callers with telephones that send Dual-tone Multi-frequency

(DTMF) tones can call in on CO lines programmed for DISA and dial stations or outgoing CO lines, without going through an attendant or operator.

To Make a Direct Inward Station

Call with DISA:

1. From outside the system, call the DISA CO line telephone number:____-____________.

2. Listen for the ringback tone signal, then listen for intercom dial tone.

3. Dial a station number.

See the system administrator for this number.

Try again if you hear busy tone.

Dial tone will be present for 10 seconds to allow direct dialing of a station intercom number or CO line access code. If a number is not dialed, the system automatically causes the DISA CO line to ring at telephones as a normal incoming call. Then, if the call is not answered within 15 seconds after the ringing starts, it will disconnect.

You will be connected when the station answers.

If you receive busy tone or wish to dial another number while ringing the station, press the * button to receive dial tone, allowing another number to be dialed.

If the call is not answered after six rings or 24 seconds, whichever comes first, busy tone will be sent. Dial * to access dial tone and dial the same or another number. To call another station after completing a DISA station call, the internal party must transfer you. Station and System

Page cannot be accessed on DISA calls.

2-40

STRATA DK FEATURE OPERATION

To Make an Outgoing Call with

DISA (Release 2 and higher):

1. From outside the system, call the DISA CO line telephone number:____-____________.

2. Listen for the ringback tone signal, then listen for intercom dial tone.

3. Dial a CO line or line group access code.

4. If a DISA security code is required, dial the code, then listen for CO dial tone.

. . . or . . .

If a DISA security code is not required, you should hear CO dial tone.

5. Dial a telephone number.

See the system administrator for this number.

Try again if you hear busy tone.

CO line number access codes are 7 0 1 ~ 7 3 6, and line group access codes are 8 1 ~ 8 8. The Least Cost Routing code (9) is not allowed.

If required, see the system administrator for this number. If the correct code is not entered, the call will be disconnected.

A timer tone that is audible to both parties will sound approximately four minutes after the call was made. Dial 0 to reset the timer each time the tone sounds for an additional four minutes. If you fail to dial 0, the call will disconnect approximately one minute after the tone.

6. Hang up when the call is completed.

DISA SECURITY CODE ENTRY/CHANGE/CANCEL (Release 2 and higher)

Only stations selected in system programming can enter, change, and cancel the DISA security code.

2-41

STRATA DK FEATURE OPERATION

To Enter, Change, or Cancel the

Code from a Selected Station:

1. Press the INT button, then dial the three-digit access code.

2. Enter the new DISA security code (1 ~ 15 digits).

3. Press the RDL button.

After you dial the access code, you will hear confirmation tone.

For security purposes, the access code is not published here, but it is available from your system administrator.

If a DISA security code is not entered, the security code will be cancelled and outgoing line access via DISA will not require a security code.

You will hear confirmation tone.

DIRECT STATION SELECTION BUTTONS

(HOTLINE)

This optional feature allows you to connect directly to another station by pressing a Direct Station Selection (DSS) button. The LED of the button shows the status (idle/busy) of the station associated with it. If connected to a CO line, pressing this button will put the outside party on hold.

Transfer the call as you would normally, by voice announcing or camping on by hanging up.

DOOR LOCK

Your telephone may have an DRLK(s), which unlock door locks when pressed.

Door Lock Button

DRLK 0

DRLK 1

DRLK 2

DRLK 3

DRLK 4

Location

_____________________

The door lock will unlock for three or six seconds when you press the button, depending on system programming. The DRLK LED will turn on during this period.

2-42

STRATA DK FEATURE OPERATION

MESSAGE WAITING

If you call a station and its user does not answer, you can leave a message waiting indication by pressing the MW/FL button. The MW/FL

LED at the called station will flash after you press the button. The user can call you back by pushing the button associated with the flashing LED.

(Voice mail devices, as well as station users, can leave message waiting indications.)

Up to four Message Waiting indications may be left at a station at one time. One of the indications is reserved for the Message Center set in system programming.

To Answer a Message Waiting

Indication on Your Telephone:

1. The MW/FL LED will flash at your station.

2. Lift the handset, press the

INT button, then the

MW/FL button.

Your phone will ring the station or voice mail device that set the indication.

Wait for an answer to receive the message.

If there is no answer, hang up and try at a later time. (The LED will continue to flash) If the MW/FL LED turns off, you have no more messages.

3. After receiving the message, place the handset on hook.

If the MW/FL LED continues to flash, you have more messages—repeat

Steps 1 ~ 3 to retrieve them.

Voice mail devices cancel the indication after a short delay set with the device.

To Set an Indication on another

Telephone:

1. Press the Intercom button and dial a station.

2. If you hear busy tone or the called station is unanswered, press the MW/FL button or dial 7 .

The MW/FL LED will flash at the called telephone.

The MW/FL LED will light steady at your telephone.

2-43

STRATA DK FEATURE OPERATION

3. Press the SPKR button.

The MW/FL LED will continue to flash at the called telephone, until the called party retrieves the message by pressing their MW/FL button.

The MW/FL LED will turn off at your station.

To Cancel the Indication Set on your Telephone:

1. Answer the Indication, as detailed above.

. . . or . . .

Press the MW/FL button.

The called party must answer—by either going off-hook or by pressing the SPKR button—for the indication to be cancelled automatically.

Do not press the INT button.

To Cancel the Indication that

You Set at another Station:

1. Dial the station number on which you left the indication.

2. Press the MW/FL button twice.

NIGHT TRANSFER

Your system can operate with two or three ringing patterns. Three-ringing pattern systems feature the DAY, DAY 2, and NIGHT modes, while tworinging pattern systems consist of the DAY and NIGHT modes. These ringing patterns are chosen by pressing the optional NT button, assigned in system programming.

The NT LED indicates the active pattern, as follows:

DAY

DAY 2

NIGHT

OFF

FLASH

OFF

N/A

2-44

STRATA DK FEATURE OPERATION

OVERRIDE CALLS

You can enter an established conversation with Executive Override.

Busy Override allows you to send a tone to a busy station to indicate that a call is waiting, and Do Not Disturb Override lets you send a tone to an idle station in the Do Not Disturb mode to indicate an important call.

To Initiate Executive Override:

1. After reaching a busy station, dial 3 .

After dialing 3, you will enter the conversation. An optional tone signal may be heard by the called parties prior to your entrance.

Your station must be enabled in system programming for Executive

Override.

To Initiate a Busy Override

Signal:

1. After reaching a busy station, dial 2 .

After dialing 2, a tone will be heard at the busy station, indicating that a call is waiting.

For Off-hook Call Announce activation:

■

If the busy station is equipped with Automatic Off-hook Call

Announce, you will not receive a busy tone and you may converse with the called party after dialing the station number.

■

If the called station is equipped for manual Off-hook Call Announce, dialing 2 or 2 1 will make an Off-hook Call Announce call to that station.

To Initiate a Do Not Disturb

Override Signal:

1. After reaching a Do Not

Disturb station, dial 2 .

After dialing 2, a tone signal will be heard at the Do Not Disturb station, indicating that a call is waiting.

Your station must be enabled in system programming to send a Do Not

Disturb Override signal.

NOTE: Privacy Override and Off-hook-Call Announce are described in separate sections of this guide.

2-45

STRATA DK FEATURE OPERATION

SPEAKERPHONE

You can make and receive calls without lifting the handset if your telephone is a speakerphone model.

OUTSIDE CALLS

You can make and receive outside calls without lifting your handset.

To Make an Outside Call (Onhook Dialing)

1. Leave the handset on-hook.

2. Press any available CO button.

. . . or . . .

Press the INT button, then dial a CO line or line group access code.

After you press the button, the CO LED will flash at the in-use rate, and you will hear dial tone.

The INT LED will flash at the in-use rate, and you will hear dial tone.

CO line access codes are 7 0 1 ~ 7 3 6; line group codes are 8 1 ~ 8 8; and the general group and Least Cost Routing code is 9.

3. Dial a telephone number.

4. Speak at a normal voice level towards the telephone.

5. Press the SPKR button to disconnect the call.

You will hear ringback tone (or busy tone, if busy).

To Receive an Incoming Call:

1. You will hear a ringing tone.

2. Leave the handset on-hook.

3. Press the CO button next to the flashing LED.

The CO LED will flash at the incoming call rate.

After you press the button, the CO LED will flash at the in-use rate, and you will be connected to the call.

2-46

STRATA DK FEATURE OPERATION

4. Speak at a normal voice level towards the telephone.

5. Press the SPKR button to disconnect the call.

TONE/VOICE FIRST SIGNALING

Your STRATA DK system may be set for Tone Signaling or Voice First

Signaling as the standard intercom call signaling method. The Tone

Signal consists of successive ring tones, while the Voice First Signal consists of a tone burst followed by the caller's voice. You can change to the alternate signaling method on a call-by-call basis.

To Change the Signaling

Method:

1. Call another station via intercom.

2. Dial 1 .

3. Speak to the party when the call is answered.

Depending on the system method, the following will happen:

■

If Tone Signaling, you will hear a ring tone (one second) every four seconds.

■

If set for Voice First Signaling, you will hear a tone burst and you wil be able to converse.

After you dial 1, the alternate method will be activated.

INTERCOM CALLS

You can make and receive intercom calls without lifting your handset.

To Make an Intercom Call (Onhook Dialing) with Voice First

Signaling:

1. Leave the handset on-hook.

2. Press the INT button.

After pressing the button, the INT LED will flash at the in-use rate, and you will hear intercom dial tone.

2-47

STRATA DK FEATURE OPERATION

3. Dial the desired station number.

4. Speak at a normal voice level toward the telephone.

5. Press the SPKR button to disconnect the call.

You will hear a single ring tone if the called station is idle. (If the call was made with Tone Signaling, you would hear ringback or busy tone.)

Dialing 1 after the station number will change the signaling method; see

"Tone/Voice First Signaling" for more information

If you dial a busy station:

■ Dial 2 or 21 to override or Off-hook Call Announce to the called station.

■ Dial 3 to Executive Override (system programmable option) the called station.

■ Dial 4 to set Automatic Call Back.

If the called station is busy or unanswered, you can dial 7 to set a

Message Waiting Indication at it.

Ask the called par ty to push the INT button if their station is a speakerphone or to pick up the handset.

MICROPHONE CONTROL

Press the MIC button to switch the microphone on and off while your telephone is in use (also see Microphone Cut-off). The MIC LED indicates the status of the microphone:

LED

OFF

MICROPHONE

OFF

All electronic telephone users can answer intercom calls handsfree (onhook) via the microphone, but only users with a speakerphone can talk handsfree when originating calls while on-hook.

The microphone and accompanying LED are always on when receiving intercom calls to allow Handsfree Answerback, and may be on or off when placing an on-hook CO line or intercom call.

■ Each station’s microphone may be set in system programming to be either on or off at the start of handsfree dialing.

■ Each station’s MIC button may be set in system programming to switch on/off with one touch or to switch off only while pressed.

2-48

STRATA DK FEATURE OPERATION

NOTES:

To change from speakerphone to handset, lift the handset.

To change from handset to speakerphone:

■

Press and hold down the SPKR button.

■

Return handset on-hook.

■

Release the SPKR button.

The MIC and MCO buttons function on Off-hook Call Announce calls for privacy.

TWO (TANDEM) CO LINE CONNECTION

This feature allows a station user to connect two CO lines, then drop out of the conversation.

To Establish a Tandem CO Line

Connection (Trk--Trk):

1. While on a CO line call, press the CONF/TRNS button.

After you press the button, you will hear intercom dial tone, the CO LED will flash at the conference rate, and the INT LED will flash at the in-use rate.

The new CO LED will flash at the in-use rate.

2. Press a CO button and dial a telephone number.

3. Press the CONF/TRNS button after the party answers.

4. Press the CONF/TRNS button.

5. Hang up.

The CO LEDs will both flash at the in-use rate, and all parties will be conferenced.

If you receive a busy tone or no answer, return to the original connection by pressing the original CO button.

You will hear intercom dial tone.

The CO LEDs will both flash at the exclusive hold rate, and the INT LED will flash at the in-use rate.

Both CO LEDs will continue to flash at the exclusive hold rate, and the two lines will be connected. The INT LED will turn off.

If the public telephone company provides auto disconnect, the connection may release automatically when the parties hang up. If not, the lines must be supervised to be disconnected (See "Supervision" that follows).

2-49

STRATA DK FEATURE OPERATION

SUPERVISION

You may have to monitor the Tandem call and disconnect the CO lines when the call is completed.

To Supervise a Tandem Call and

Release It:

1. Press either CO button.

After you press the button, you will be connected to both CO lines, and both CO LEDs will flash at the In-use rate.

Both CO LEDs will turn off, and the connection will be released.

2. If the parties have hung up, go back on-hook.

. . . or . . .

If the parties are still talking, press the CONF/TRNS button and hang up.

TIMED REMINDERS

You can set five separate reminders at your station. Your telephone will sound a distinct beeping at the exact minute and hour you set for any of these reminders, either one time or daily.

To Enter a Timed Reminder:

1. Press the INT button and dial

6 0 5 ~ 6 0 9 .

2. Enter the desired time.

You have a choice of five different reminders.

Set the time by entering two digits for the hour of the day (HH), then two digits for the minute. To enter a reminder for 8: 30 a.m., enter 0 8 for the hour, then 3 0 for the minute. To enter a reminder for 8: 03 p.m., enter 2 0 for the hour (8 p.m is the 20th hour of the day), then 0 3 for the minute.

3. Dial 0 for the reminder to be repeated every day, or 1 for a one-time reminder only.

4. Press the RDL (or # ) button.

The time will be recorded in memory, and you will hear a beeping tone for

30 seconds (or until cancelled by going off-hook) when the hour and minute occur.

2-50

STRATA DK FEATURE OPERATION

To Cancel a Timed Reminder:

1. Press the INT button, then dial 6 0 5 ~ 6 0 9 .

2. Press the RDL (or # ) button.

Dial 6 0 5 to cancel the reminder set for 6 0 5; or dial 6 0 6 to cancel the reminder set for 6 0 6, etc. You can only cancel one reminder at a time.

The reminder will be cancelled.

TOLL RESTRICTION OVERRIDE/TRAVELING

CLASS

You can completely override Toll Restriction at selected stations or, with

Release 3 and higher, you can change the station's Toll Restriction class to another class. The station will resume its normal class at the conclusion of the call.

To Override/Change Toll

Restriction:

1. Lift the handset.

2. Press a Toll Restricted CO button.

After pressing the button, you will hear dial tone, and the CO LED will flash at the in-use rate.

You can also press the INT button, then dial a line number or line group access code to seize a CO line

You will no longer hear dial tone.

3. Press the CONF/TRNS button and enter 4 7 .

4. Enter the Toll Restriction

Override Code (four digits).

You will hear dial tone.

For security reasons, the override codes are only available on a selected basis. See your system administrator.

5. Dial a telephone number.

2-51

STRATA DK FEATURE OPERATION

TOLL RESTRICTION OVERRIDE/TRAVELING

CLASS CODE REVISION

Stations selected in system programming can add, delete, and change the Toll Restriction Override/Traveling Class codes.

To Add, Delete, or Change

Override/ Traveling Class Codes from a Selected Station:

1. Press the INT button, then enter the three-digit Toll

Restriction Override Change

Access Code.

2. Enter a four-digit override code.

3. Press the RDL (or # ) button.

After entering the code, you will hear confirmation tone.

For security reasons, the change access code is not in this guide. It is available from your telephone system administrator.

You will hear confirmation tone, and the code will be stored in memory.

Repeat Steps 1 ~ 3 to enter more Toll Restriction Override/Traveling

Class codes.

AUTOMATIC HOLD

(Release 4 and higher)

You can automatically place a call on a CO line button on-hold by just pressing another outside line or the Intercom button—there is no need to push the HOLD button. You can also switch between the new call and the original call without having to press the HOLD button. Automatic Hold is assigned on a station-by-station basis in system programming.

To Use Automatic Hold

1. While on an outside call, press another CO button or the INT button to receive or originate a new call.

After you press the button, the original CO LED will flash at the on-hold rate, and the original call will be placed on-hold.

The LED of the new call will flash at the in-use rate, and the new line will be accessed.

2-52

STRATA DK

To Switch between Calls:

1. Press the CO or INT button of the held call.

FEATURE OPERATION

The LED of the line just automatically placed on-hold will flash at the Onhold rate, and the LED of the line just accessed will flash at the In-use rate.

USER PROGRAMMABLE FEATURE BUTTONS

(Release 4 and higher)

You can program Speed Dial buttons or codes to access features, as well as telephone numbers. You can store up to 20 digits, enabling you to access a sequence of features, such as Call Park and Page, with a code in a Speed Dial button. A list of feature access codes follows these storage instructions.

To Store Feature(s) or Telphone

Numbers on a Button:

1. Do not lift the handset.

2. Press the RDL (or # ) button.

3. Press one of the SD buttons.

4. Enter a feature access code or sequence of codes.

5. Press the RDL (or # ) button.

If you lifted the handset in Step 1, the system would automatically dial the number that you most recently dialed.

Refer to the Feature Access Code List that follows in the next few pages.

You can enter 20 digits maximum. Dial pad digits count as 1 digit, while the CONF/TRNS and INT feature buttons each count as two.

The feature access code or codes will be stored in memory.

NOTES:

With Release 4 and higher, if the preceding sequence is not completed within one or three minutes (system programmable time), the operation will time out and your telephone will be placed in the idle condition.

To exit the entry mode to answer or make a call, press the RDL button.

2-53

STRATA DK FEATURE OPERATION

To Store Codes in a System or

Station Speed Dial Location:

1. Do not lift the handset.

2. Press the RDL (or # ) button, then the SDS (or * ) button.

3. Dial a 2-digit Speed Dial location.

4 Enter a feature access code or sequence of codes.

5. Press the RDL (or # ) button.

If you lifted the handset in Step 1, the system would automatically dial the number that you most recently dialed after you press the RDL button.

Station Speed Dial locations are 1 0 ~ 4 9. System Speed Dial locations are 6 0 ~ 9 9 and can only be stored at Station 200 (typically the system administrator's station).

Refer to the Feature Access Code List on the following pages.

You can enter 20 digits maximum. Dial pad digits count as 1 digit, while the CONF/TRNS and INT feature buttons each count as two.

The feature access code or codes will be stored in memory.

NOTES:

To exit the entry mode to answer or make a call, press the RDL button.

2-54

STRATA DK FEATURE OPERATION

FEATURE

Automatic Call Back

Background Music

(External Speakers On)

Background Music

(External Speakers Off)

Call Forward — All Calls

To Station

Call Forward — Busy

To Station

Call Forward

— Busy/No answer

To Station

Call Forward — No Answer

To Station

Call Forward Cancel

To Station

Call Park

Call Park Retrieve

(Pickup at your own station)

Door Phone Calling

(Door Phone must be idle)

Hookflash Signal

Off-hook Call Announce

6500 SERIES TELEPHONE FEATURE CODE

RDL + SD + 4 + RDL

RDL + SD + INT + 4 9 1 + RDL (Station 200 only)

RDL + SD +

INT

NT +

INT

4 9 0

6 0 1

6 0 2

6 0 4

6 0 1

+ RDL (Station 200 only)

6 0 3 the station number + RDL

+ the station number + RDL

+ RDL

CONF/TRANS

INT

+ 4 2

+ 4 1

+ RDL

door phone intercom number + RDL

RDL + SD + CONF/TRANS + 45 + RDL

RDL + SD + 2 + RDL

NOTES:

The storage sequence for User Programmable Feature Buttons is as follows:

RDL + SD + Access Code(s) + RDL

This feature will place an existing call on hold when the button is pressed. If the button is pressed when not on a call,

page will still be accessed.

CO line access codes: 701 ~ 736 for individual line; 81 ~ 88 for line group or 9 for general group or LCR.

If RDL does not appear on your telephone, use # or Redial instead.

Table 2-A

Feature Access Code List

2-55

STRATA DK FEATURE OPERATION

FEATURE

Overrides

(Busy, DND)

Overrides

(Executive)

Paging (CO line Auto Hold 2 )

(All Call, Digital and Electronic telephones)

Paging 2

(Station Group A)

Paging 2

(Station Group B)

Paging 2

(Station Group C)

Paging 2

(Station Group D)

Paging 2

(External Page Zone A)

Paging 2

(External Page Zone B)

Paging 2

(External Page Zone C)

Paging 2

(External Page Zone D)

Paging 2

(All Call, External Page Zone)

6500 SERIES TELEPHONE FEATURE CODE

RDL 4 + SD + 2 + RDL

RDL + SD + 3 + RDL

RDL + SD + HOLD + INT + 3 0 + RDL

RDL + SD + HOLD + INT + 3 1 + RDL

RDL + SD + HOLD + INT + 3 2 + RDL

RDL + SD + HOLD + INT + 3 3 + RDL

RDL + SD + HOLD + INT + 3 4 + RDL

RDL + SD + HOLD + INT + 3 5 + RDL

RDL + SD + HOLD + INT + 3 6 + RDL

RDL + SD + HOLD + INT + 3 7 + RDL

RDL + SD + HOLD + INT + 3 8 + RDL

RDL + SD + HOLD + INT + 3 9 + RDL

NOTES:

The storage sequence for User Programmable Feature Buttons is as follows:

RDL + SD + Access Code(s) + RDL

This feature will place an existing call on hold when the button is pressed. If the button is pressed when not on a call,

page will still be accessed.

CO line access codes: 701 ~ 736 for individual line; 81 ~ 88 for line group or 9 for general group or LCR.

If RDL does not appear on your telephone, use # or Redial instead.

Table 2-A

Feature Access Code List (continued)

2-56

STRATA DK FEATURE OPERATION

FEATURE

Pickup (CO line Auto Hold) 2

(Directed to station, new, or transferred call)

Pickup 2

Any ringing CO line

(new call only)

Pickup Station Page or

Door Phone Ringing 2

Pickup 2

External Page

One-touch Voice Mail Access

Outgoing Calls

6500 SERIES TELEPHONE FEATURE CODE

RDL + SD + HOLD + INT + 5 + station number + RDL

RDL + SD + HOLD + INT + 59 + RDL

RDL + SD + HOLD + INT + 530 + RDL

RDL + SD + HOLD + INT + 535 + RDL

RDL + SD + INT + VM intercom number + RDL

RDL + SD + INT + CO line access code 3 + telephone number + RDL

NOTES:

The storage sequence for User Programmable Feature Buttons is as follows:

RDL + SD + Access Code(s) + RDL

This feature will place an existing call on hold when the button is pressed. If the button is pressed when not on a call,

pickup will still be accessed.

CO line access codes: 701 ~ 736 for individual line; 81 ~ 88 for line group or 9 for general group or LCR.

If RDL does not appear on your telephone, use # or Redial instead.

Table 2-A

Feature Access Code List (continued)

2-57

Chapter 3

STRATA DK TOSHIBA VP INTEGRATION

USING THE TOSHIBA VP SYSTEM

This chapter explains how to program your telephone for Call Forward and message retrieval when using the Toshiba Voice Processing (VP)

System (i.e., the VP 100, the VP 200, or the VP 300) with your STRATA

DK system.

Refer to the Toshiba Voice Processing User Guide for more user information about the Toshiba VP system. Other related documents include: the Toshiba Voice Processing Quick Reference Guide, the

Toshiba Voice Processing Product and Feature Description Manual, the

Toshiba Voice Processing Configuration Manual, the VP 100 Installation

and Maintenance Manual, the VP 200 Installation and Maintenance

Manual, and the VP 300 Installation and Maintenance Manual.

CALL FORWARD

You can program your telephone to forward to the Toshiba VP System to answer your calls when you are busy or not available.

VOICE MAIL IDENTIFICATION CODE

3. Dial 9 1 .

4. Enter your mailbox number.

5. Press the RDL button.

To direct forwarded call to your mailbox—your personal storage space for voice messages—and to ensure that callers receive your personal greeting, you must store a Voice Mail (VM) Identification (I.D.) code once from your telephone.

To Store the Voice Mail ID Code:

1. Press the INT button.

2. Dial 6 5 6 .

After you press the button, you will hear intercom dial tone.

You will hear confirmation tone. "656" is the VP System Identification code when Call Forward is set. This code does not forward calls to the

VP system.

You will hear confirmation tone. The VM I.D. code will be automatically sent to the VP system whenever calls are forwarded to it.

3-1

STRATA DK TOSHIBA VP INTEGRATION

NOTE: Steps 1 ~ 5 are required for the initial storage of VM I.D. code to the VP system. Once programmed, these digits remain in memory until changed. Repeat Steps 1 ~ 5 to change the code.

To Cancel the Voice Mail I.D.

Code:

1. Press the INT button.

2. Dial 6 5 6 .

3. Press the RDL button.

4. Press the SPEAKER button.

You will hear intercom dial tone after you press the button.

You will hear confirmation tone.

The I.D. code will be cancelled.

CALL FORWARD TO TOSHIBA VP VOICE SYSTEMS

By registering Call Forward to the Toshiba VP System on your telephone, information about the call will automatically be provided to the VP system, so that the caller does not have to re-enter the last few digits of the extension number that they have initially dialed.

To Forward Calls to the Toshiba

VP System:

1. Press the desired Call

Forward button.

. . . or . . .

Press the INT button, then enter a Call Forward access code.

2. Dial the VP System number.

The LED associated with the button will flash after you press the button.

You will hear confirmation tone after entering the access code.

NOTE: Following is a list of Call Forward access codes:

■ Call Forward-All Calls: 601

■ Call Forward-Busy: 602

■ Call Forward-No Answer: 603

■ Call Forward-Busy-No Answer: 604

See your system administrator for the correct voice mail intercom number. After dialing, you will hear confirmation tone.

3-2

STRATA DK TOSHIBA VP INTEGRATION

3. Press the Call Forward button or the SPKR button.

The Call Forward button LED will light steady if you pressed a Call

Forward button in Step 1.

To Cancel Call Forward to the

Toshiba VP System:

1. Press the appropriate Call

Forward button.

. . . or . . .

Press the INT button, enter

6 0 1 , then press the SPKR button.

The Call Forward button LED will turn off, and Call Forward will be cancelled.

You will hear confirmation tone, and Call Forward will be cancelled.

MESSAGE RETRIEVAL

You can program your MW/FL button to automatically retrieve your voice mail messages when your press it.

To Program your MW/FL Button to Retrieve Messages:

1. Press the INT button.

2. Dial 6 5 7 .

You will hear confirmation tone after you press the button.

You will hear confirmation tone. "657" is the VP System Identification code when Call Forward is set. This code does not not forward calls to the VP system.

3. Dial 9 2 .

4. Enter your mailbox number, then # # .

5. Enter your security code.

Your telephone must have the SDS button for the properly with the VP system.

# button to function

Storing your security code will save you from having to enter your security code every time you access your mailbox; however, this will also allow anyone to retrieve your messages. If a security code is not desired, do not include it.

3-3

STRATA DK

6. Press the RDL button.

7. Press the SPKR button.

You will hear confirmation tone.

TOSHIBA VP INTEGRATION

To Retrieve Messages with the

MW/FL button:

1. When the MW/FL LED flashes, press the INT button.

2. Press the MW/FL button. The VP System will be called and you should be able to listen to your messages.

3-4

Chapter 4

STRATA DK CENTREX APPLICATION

GENERAL

Your system may be equipped with the Centrex Application, which enhances its feature capability when installed behind a Centrex or PBX system.Your telephone may have access to one or more of the enhanced

Centrex features listed below:

FLEXIBLE INTERCOM NUMBERING

A station intercom number can be three or four digits. It is, therefore, possible to match a station’s intercom and Centrex line extension number. Dial the entire station number when indicated.

NOTE: Some access code numbers may have been changed to avoid system numbering plan conflicts,

CENTREX FEATURE BUTTONS

You may access some Centrex features by pressing a preprogrammed flexible button on your telephone, instead of dialing a Centrex access code. The Centrex access code, including the necessary flash and/or pause sequence, is activated when the button is pressed. See your

Centrex or PBX operations manual for specific details.

RINGING REPEAT

The distinctive ring patterns available in your Centrex system are automatically repeated with your telephone, allowing you to answer appropriately for either outside, inside or callback calls.

DELAYED RINGING

CO or Centrex line(s) may be programmed for a 12-second and/or 24second ring delay at stations to permit alternate answering conditions.

4-1

Appendix

STRATA DK CUSTOMIZED LISTINGS

FEATURE ACCESS CODE RECORD

The STRATA DK system default feature access codes are used in this guide. The access codes of some features, which follow in the left-hand column, may have been changed in system programming.

Feature

All Call Page-Telephones

All Call Page-Telephones/External Speakers

Automatic Busy Redial

Automatic Busy Redial Cancel

BGM Over External Speakers Off

BGM Over External Speaker On

BGM Over Station Off

BGM Over Station On

Call Forward-All Calls

Call Forward-Busy

Call Forward-Busy/No Answer

Call Forward-No Answer

Call Hold/Park

Call Hold/Park Pickup

Call Pickup

CO Line-Outgoing Calls

CO Line Group-Outgoing Calls

DISA Security Code Change

Door Phones

External Page Zones

Least Cost Routing

Station Group Page

Station Speed Dial Set

System Speed Dial Set

Toll Restriction Override

Toll Restriction Override Code Change

Timed Reminder

Verified Account Code Change

VM ID Code Set-Call Forward

VM ID Code Set-Message Retrieval

Access Code

______________

A-1

STRATA DK CUSTOMIZED LISTINGS

SPEED DIAL CODE ASSIGNMENTS

Both System and Station Speed Dial Codes can be programmed for telephone numbers or feature access codes.

System Speed Dial Code Assignments

60: 61: 62:__

65: 66:

70: 71:

67:__________

72:__________

75: 76:

80: 81:

85: 86:

90: 91:

95: 96:

77:__________

82:__________

87:__________

92:__________

97:__________

Station Speed Dial Code Assignments

10: 11: 12:__

15: 16:

20: 21:

17:__________

22:__________

25: 26:

30: 31:

35: 36:

40: 41:

45: 46:

27:__________

32:__________

37:__________

42:__________

47:__________

A-2

63: 64:

68: 69:

73: 74:

78: 79:

83: 84:

88: 89:

93: 94:

98: 99:

13: 14:

18: 19:

23: 24:

28: 29:

33: 34:

38: 39:

43: 44:

48: 49:

STRATA DK CUSTOMIZED LISTINGS

CODE

COMMENT

ACCOUNT CODES

CODE

COMMENT

STATION

GROUP

STATION

GROUP

AREA

PAGING

ZONE

EXTENSION

ZONE

COMMENT

A-3

Off-hook Call

On-hook Call

Outgoing Call

Outside Call

Pooled Line

Pulse Dialing

Station

Station 200

Glossary

STRATA DK

CO Line

Direct Inward System Access

Dual-tone Multi-frequency

General Group

Hookflash

Incoming Call

Intercom Call

Least Cost Routing

GLOSSARY

Link to the public telephone network.

Feature which allows callers to call into the STRATA DK system, then dial outgoing CO lines or stations without going through an attendant or operator.

Tones generated when dialing from push-button telephones.

CO line arrangement in which all lines are arranged into one group, which can be accessed by dialing 9.

Operation in which a call is disconnected and CO line dial tone is recalled.

Call originated from outside of the STRATA DK system to a system CO line.

Call which involves STRATA DK stations only.

Feature which routes outgoing calls over the least costly lines. Station users dial 9 plus a telephone number to make a call with Least Cost

Routing.

Call in which the handset of a station is lifted.

Call in which the handset of a station is not lifted.

Call originated from a STRATA DK station to a telephone number outside of the system.

Call which involves a STRATA DK station and a telephone outside of the system.

CO line button or access code which has more than one CO line assigned to it.

Dialing mode on outgoing calls which uses rotary dial pulses.

Telephone.

Telephone, which can usually be reached by dialing 2 0 0, where System

Speed Dial numbers can be stored.

Glossary-1

STRATA DK

System Administrator

Tandem Call

Tone Dialing

Tone First Signaling

Voice First Signaling

GLOSSARY

Person who oversees the operation of the STRATA DK system.

Call in which two STRATA DK system CO lines are connected, such as a

Direct Inward System Access call or a Conference call.

Dialing mode on outgoing calls which uses Dual-tone Multi-frequency

(DTMF) tones.

Signaling method on station-to-station calls in which the called station rings until answered or the calling party hangs up.

Signaling method on station-to-station calls in which the called station receives a tone burst followed by a voice announce from the caller.

Glossary-2

Index

STRATA DK INDEX

Account Code Calls 2-32

Emergency Override of Forced

Account Codes 2-33

Forced Account Codes 2-32

Verified Account Codes 2-34

Voluntary Account Codes 2-33

Alarm Reset 2-38

Automatic Busy Redial 2-5

Automatic Callback 2-30

CO Line Queuing with

Automatic Callback 2-31

Automatic Hold 2-52

Automatic Off-hook Selection 2-5

Background Music (BGM) Over

Telephone Speakers 2-39

Background Music (BGM) Over

External Speakers 2-39

Call Forward2-23

Call Forward-All Calls 2-23

Call Forward-Busy 2-24

Call Forward-Busy/No Answer

2-25

Call Forward-Fixed 2-26

Call Forward-No Answer 2-24

Call Hold 2-26

Call Park 2-27

Call Pickup 2-28

Directed Call Pickup 2-29

Call Transfer with Camp-on 2-18

Answering a Transferred Call

2-19

Centrex Application 4-1

Centrex Feature Buttons 4-1

Delayed Ringing 4-1

Flexible Intercom Numbering

4-1

Ringing Repeat 4-1

Conference Calls 2-21

Conference with Stations and

CO Lines 2-21

Conference with Stations Only

2-22

Customized Listings Appendix-1

Account Codes Appendix-3

Feature Access Code Record

Appendix -1

Paging Appendix -3

Speed Dial Code Assignments

Appendix -2

Direct Inward System Access

(DISA) 2-40

DISA Security Code

Entry/Change/Cancel 2-41

Direct Station Selection Buttons

(Hotline) 2-42

Do Not Disturb 2-30

Door Lock 2-42

Door Phone 2-36

DTMF Tone Dialing With * and # 2-

Exclusive Hold 2-28

Feature Buttons 1-1

Glossary Glossary-1

Group Listening 2-4

Handsfree Answerback 2-16

Handsfree Monitoring 2-38

Intercom Calls 2-15

LED Indications 1-5

Message Waiting 2-43

Microphone Control 2-48

Microphone Cut-off 2-17

Night Transfer 2-44

Off-hook Call Announce (OCA)

2-17

Forced Disconnect 2-18

On-hook Dialing 2-3

Intercom Calls 2-3

Outside Calls 2-3

Outside Calls 2-1

Override Calls 2-45

Paging 2-35

All Call Page Button 2-36

Privacy Button 2-14

Privacy Release 2-14

Repeat Last Number Dialed 2-5

Saved Number Redial 2-12

Speakerphone 2-46

Intercom Calls 2-47

Outside Calls 2-46

Tone/Voice First Signaling 2-47

Speed Dial 2-7

Index-1

STRATA DK

Calling System or Station

Speed Dial Numbers 2-10

Chain Dialing Speed Dial

Numbers 2-11

Speed Dial Number Linking 2-9

Speed Dial Pause and Flash

Storage 2-9

Station Speed Dial Storage 2-7

System Speed Dial Storage 2-8

Timed Reminders 2-50

Toll Restriction Override/Traveling

Class 2-51

Toll Restriction Override/Traveling

Class Code Revision 2-52

Tone/Pulse Dialing 2-13

Toshiba VP Integration 3-1

Call Forward to Toshiba VP

Systems 3-2

Message Retrieval 3-3

Voice Mail Identification Code

3-1

Two (Tandem) CO Line

Connection 2-49

Supervision 2-50

User Programmable Feature

Buttons 2-53

Volume Controls 1-5

Index-2

INDEX

Hello! I am an AI chatbot specifically trained to assist you with the Strata DK96 User Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated

STRATA DK

ELECTRONIC TELEPHONE USER GUIDE

© COPYRIGHT 1992 TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

Release _________

Issue 1, September 1992

TRADEMARKS AND SERVICE MARKS

Table of Contents

SUBJECT PAGE

FIGURE LIST

TABLE LIST

TABLE

TITLE PAGE

Introduction

GENERAL DESCRIPTION

PURPOSE

ORGANIZATION

HOW TO USE THIS GUIDE

Figure

-1

Sample Page

Figure

-2

20-button Electronic Telephone

Chapter 1

PURPOSE

FEATURE BUTTONS

VOLUME CONTROLS

LED INDICATIONS

Chapter 2

OUTSIDE CALLS

ON-HOOK DIALING

GROUP LISTENING

AUTOMATIC OFF-HOOK SELECTION

REPEAT LAST NUMBER DIALED

AUTOMATIC BUSY REDIAL

SPEED DIAL

SAVED NUMBER REDIAL

DTMF TONE DIALING WITH

AND #

TONE/PULSE DIALING

PRIVACY OVERRIDE

PRIVACY BUTTON (Release 3 and higher)

PRIVACY RELEASE

INTERCOM CALLS

HANDSFREE ANSWERBACK

MICROPHONE CUT-OFF

OFF-HOOK CALL ANNOUNCE (OCA)

CALL TRANSFER WITH CAMP-ON

CONFERENCE CALLS

CALL FORWARD

CALL HOLD

EXCLUSIVE HOLD

CALL PICKUP

DO NOT DISTURB

AUTOMATIC CALLBACK

ACCOUNT CODE CALLS

PAGING

DOOR PHONE

HANDSFREE MONITORING

ALARM RESET

BACKGROUND MUSIC (BGM) OVER

TELEPHONE SPEAKERS

BACKGROUND MUSIC (BGM) OVER EXTERNAL

SPEAKERS

DIRECT INWARD SYSTEM ACCESS (DISA)

DIRECT STATION SELECTION BUTTONS

(HOTLINE)

DOOR LOCK

MESSAGE WAITING

NIGHT TRANSFER

OVERRIDE CALLS

SPEAKERPHONE

MICROPHONE CONTROL

TWO (TANDEM) CO LINE CONNECTION

TIMED REMINDERS

TOLL RESTRICTION OVERRIDE/TRAVELING

CLASS

TOLL RESTRICTION OVERRIDE/TRAVELING

CLASS CODE REVISION

AUTOMATIC HOLD

60: 61: 62:__

65: 66:

70: 71:

75: 76:

80: 81:

85: 86:

90: 91:

95: 96:

10: 11: 12:__

15: 16:

20: 21:

25: 26:

30: 31:

35: 36:

40: 41:

45: 46:

63: 64:

68: 69:

73: 74:

78: 79:

83: 84:

88: 89:

93: 94:

98: 99:

13: 14:

18: 19:

23: 24:

28: 29:

33: 34:

38: 39:

43: 44:

48: 49: