ACS-2702A
ACS-2702A
Intel Bay Trail N2930/E3845 IP67 Waterproof Box PC
User Manual
Release Date
Revision
Nov. 2015
V1.0
®2015 Aplex Technology, Inc.
All Rights Reserved.
Published in Taiwan
Aplex Technology, Inc.
15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan
Tel: 886-2-82262881
Fax: 886-2-82262883 E-mail: [email protected]
URL: www.aplextec.com
Revision History
Reversion
Date
Description
1.0
2015/11/27
Official Version
ACS-2702A User Manual
1
Warning!________________________
This equipment generates, uses and can radiate radio frequency energy and
if not installed and used in accordance with the instructions manual, it may cause
interference to radio communications. It has been tested and found to comply
with the limits for a Class A computing device pursuant to FCC Rules, which are
designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference in which case the user at his own
expense will be required to take whatever measures may be required to correct
the interference.
Electric Shock Hazard – Do not operate the machine with its back cover removed.
There are dangerous high voltages inside.
Caution
Risk of explosion if the battery is replaced with an incorrect type.
Batteries should be recycled where possible. Disposal of used batteries must be in
accordance with local environmental regulations.
Disclaimer
This information in this document is subject to change without notice. In no event
shall Aplex Technology Inc. be liable for damages of any kind, whether incidental or
consequential, arising from either the use or misuse of information in this document
or in any related materials.
ACS-2702A User Manual
2
Packing List
Accessories (as ticked) included in this package are:
□ Adaptor
□ Driver & manual CD disc
□ Other.___________________(please specify)
ACS-2702A User Manual
3
Safety Precautions
Follow the messages below to prevent your systems from damage:
◆ Avoid your system from static electricity on all occasions.
◆ Prevent electric shock. Don‘t touch any components of this card when
the card is power-on. Always disconnect power when the system is not
in use.
◆ Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.
ACS-2702A User Manual
4
Table of Contents
Revision History………………………………………………………………….………………………………….1
Warning!/Caution/Disclaimer…...............................................…………………………….…2
Packing List…………………………………….………………………………….…………………………………..3
Safety Precautions……………………………………………………………..……….…..……………………..4
Chapter 1
Getting Started
1.1 Features………………………..………………………...……………………….…..7
1.2 Specifications…………………...……………………………………………….….7
1.3 Dimensions………………………....…………………………………………….….8
1.4 Brief Description of ACS-2702A.……..….………………………..………..9
Chapter 2
Hardware
2.1 Mainboard Introduction…………………..…...…………………………....10
2.2 Specifications…………………………..…….……………………………………10
2.3 Jumpers and Connectors Location….…………………………………...14
2.4 Jumpers Setting and Connectors…..………………………………..……15
Chapter 3
BIOS Setup
3.1 Operations after POST Screen…...…….……...……….…………………27
3.2 BIOS Setup Utility…………………………………………….………………….27
3.3 Main Settings……………………………………..…………….…………………28
3.4 Advanced Settings…………………………………………….………………...29
3.5 Chipset Settings……………………………………….……….………………...37
3.6 Security Settings…………………………………………….….………………..39
3.7 Boot Settings…..………………………………………….……..………………..40
3.8 Save & Exit Settings……………………………………..……..……………....41
Chapter 4
Installation of Drivers
4.1 Intel (R) AtomTM SoC Chipset ………..……...…………..………………44
4.2 Intel (R) VGA Chipset…………………………………………….….……......47
4.3 Intel (R) LAN Driver………..…………………………………….…..………...51
4.4 Realtek ALC662 HD Audio Driver Installation………..…………..…54
4.5 USB 3.0 Driver…………………………………….……………………………….56
4.6 Com Driver………………………………………….……………………………….59
ACS-2702A User Manual
5
Figures
Figure 1.1: Dimensions of ACS-2702A……..………….……………..……………......8
Figure 1.2: Dimensions of ACS-2702A – Option….………………………………….8
Figure 1.3: Overview of ACS-2702A……………...…….…………………………….....9
Figure 2.1: Mainboard Dimensions…………………….……………………………….13
Figure 2.2: Jumpers and Connectors Location-Board Top…..…………….….14
Figure 2.3: Jumpers and Connectors Location-Board Bottom….………..…14
ACS-2702A User Manual
6
Chapter 1
Getting Started
1.1 Features

Fanless Design

Intel Bay Trail N2930 (1.83GHz) CPU built-in/E3845 (1.91GHz) for option

Onboard 4GB DDR3L 1600MHz

Wide-ranging 9~36V DC Power Input

IP67 Certified and IP69K Compliant

1 x 2.5” SATA II HDD Space
1.2 Specifications
System
CPU
Onboard Intel Bay Trail N2930(1.83GHz) CPU built-in
Onboard Intel Bay Trail E3845(1.91GHz) CPU for option
Chipset
SoC
Memory
Onboard 4GB DDR3L 1600MHz
USB
2 x USB 2.0 by 1 x M12 8-pin connector
Serial/Parallel
1 x RS-232/422/485, COM1, Default RS-232, by M12 connector
1 x RS-232, COM2, by M12 connector
VGA
1 x VGA by M12 connector
LAN
1 x GbE LAN by M12 connector
Power
1 x DC Power by M12 connector
IO Port
Storage Space
Storage
1 x 2.5” SATAII HDD
1 x Internal SD slot, up to 32GB
Expansion
Expansion Slot
1 x Internal Mini PCIe slot full size
Power
Power Input
9~36V DC
Power Consumption
MAX: 6.3W
Mechanical
Construction
Stainless Steel Chassis
Mounting
Wall Mount
IP Raing
IP67 Certified and IP69K Compliant
Dimension
250 x 200 x 58.6 mm
ACS-2702A User Manual
7
Net Weight
3.1 Kg
Environmental
Operating temperature
-20~60°C
Storage temperature
-40~85°C
Storage humidity
10 to 90% @ 40°C, non- condensing
Certification
CE / FCC Class A
Operating System Support
OS Support
Windows Embedded 8.1 Industry Pro,
Windows 7 Pro for Embedded,
Windows Embedded Standard 7,
Windows Embedded 8 Standard
1.3 Dimensions
Standard
Figure 1.1: Dimensions of ACS-2702A
Option
Figure 1.2: Dimensions of ACS-2702A - Option
ACS-2702A User Manual
8
1.4 Brief Description of ACS-2702A
The ACS-2702A is a fanless Design high-efficiency thermal solution BOX PC,
powered by Intel Bay Trail N2930 1.83GHz Processor and supporting 4GB DDR3L
1600MHz onboard memory. Intel Bay Trail E3845 1.91GHz is for option. It comes with
2 x USB 2.0, 2 x COM ports, 1 x VGA, 1 x LAN, 1 x DC Power, all by M12 connector. It
supports 1 x 2.5” SATAII HDD space, 1 x internal SD slot up to 32GB, and 9~36V DC
wide-ranging power input. It is IP67 certified and IP69K compliant waterproof. It is
ideal for industrial automation, factory automation, machine vision, process control,
data terminal, TI, surveillance, etc. and running factory operations from small visual
interface and maintenance applications to large control process applications. The
ACS-2702A works very well along with any of our display series and it absolutely can
provide an easy way to perform control and field maintenance.
Figure 1.3: Overview of ACS-2702A
ACS-2702A User Manual
9
Chapter 2
Hardware
2.1 Mainboard Introduction
SBC-7111 is a 4" industrial motherboard developed on the basis of Intel Bay trail-I/M
Processors, which provides abundant peripheral interfaces to meet the needs of
different customers. Also, it features dual GbE ports, 3-COM ports and one Mini PCIE
configuration, one VGA port, one HDMI port, one LVDS interface. To satisfy the
special needs of high-end customers, CN1 and CN2 and CN3 richer extension
functions. The product is widely used in various sectors of industrial control.
2.2 Specifications
Specifications
Board Size
170mm x 113mm
CPU Support
Intel Bay Trail E3845 / 1.91GHz (4cores, 10W, onboard)
Intel Bay Trail N2930 / 1.83 up to 2.16GHz (4cores,TDP/7.5W, option)
Intel Bay Trail E3815 / 1.46GHz (1core, 5W, option)
Chipset
SoC
Memory Support
Onboard 2GB DDR3L SDRAM (E3845/N2930/E3815, option)
Onboard 4GB DDR3L SDRAM (E3845/N2930, option)
Graphics
Intel® HD Graphics 542/792MHz (E3845)
Intel® HD Graphics 313/854MHz (N2930)
Intel® HD Graphics 400MHz (E3815)
Display Mode
1 x HDMI Port
1 x LVDS (18/24-bit dual LVDS)
1 x CRT Port
Support
Up to 1920 x 1200 for HDMI
Resolution
Up to 1920 x 1200 for LVDS (PS8625)
Up to 1920 x 1200 for CRT
Dual Display
HDMI + LVDS
HDMI + CRT
LVDS + CRT
Super I/O
ACS-2702A User Manual
ITE IT8518E
10
Fintek F81216AD
BIOS
AMI/UEFI
Storage
1 x SATAII Connector (7P)
1 x SATAII Connector (7P + 15P)
1 x SD Slot
Ethernet
2 x PCIe Gbe LAN by Intel 82574L
1 x USB 2.0 and 1 x USB 3.0 (type A)stack ports (USBCON1/USB0,USB1)
1 x USB 2.0 Pin header for CN1 (USB3 or Touch, option)
USB
1 x USB 2.0 Hub(USB2)
1 x USB 2.0 Pin header for CN2 (USB Hub /USB1)
2 x USB 2.0 Pin header for CN3 (USB Hub /USB2/USB3)
1 x USB 2.0 for MPCIE1 (USB Hub /USB4)
1 x RS232/RS422/RS485 port, DB9 connector for external (COM1) Pin 9
w/5V/12V/Ring select
Serial
1 x RS232 port, DB9 connector for external (COM2) Pin 9
w/5V/12V/Ring select
2 x UART for CN3 (COM3,COM4)
1 x RS422/485 header for CN2 (IT8518E/COM5)
Digital I/O
8-bit digital I/O by Pin header (CN2)
4-bit digital Input
4-bit digital Output
4-bit digital I/O by Pin header (CN3)
2-bit digital Input
2-bit digital Output
Battery
Support CR2477 Li battery by 2-pin header (BAT1/CMOS)
Smart Battery
1 x Smart battery
Support 3 Serial Li battery by 8-pin header (BAT2)
Audio
Support Audio via Realtek ALC662-VD HD audio codec
Support Line-in, Line-out, MIC by 2x6-pin header
Keyboard /Mouse
1 x PS2 keyboard/mouse by box pin header (CN3)
Expansion Bus
1 x mini-PCI-express slot
1 x PCI-express (CN3)
Touch Ctrl
1 x Touch ctrl header for TCH1 (ITE8518E/COM6)
(JP4 setting:RS232 or USB 2.0)
ACS-2702A User Manual
11
Power Management
Wide-ranging DC9V~36V input
1 x 3-pin power input connector
Switches and
1 x Power on/off switch (BT1/BT2/CN2/CN3)
LED Indicators
1 x Reset (CN2)
1 x Power LED status (CN1)
1 x HDD LED status (CN2)
1 x Buzzer
External I/O port
2 x COM Ports (COM1/COM2)
2 x USB 2.0 Ports (stack)
2 x RJ45 GbE LAN Ports
1 x HDMI Port
1 x Stack audio Jack (Line out)
Watchdog Timer
Temperature
Humidity
Software programmable 1 – 255 second by Super I/O (Reserve)
Operating: -20℃ to 70℃
Storage: -40℃ to 85℃
10% - 90%, non-condensing, operating
2V /0.80A (Intel Bay Trail E3845 processor with 4GB DDR3L DRAM)
Power Consumption
12V /0.70A (Intel Bay Trail N2930 processor with 4GB DDR3L DRAM)
12V /0.60A (Intel Bay Trail E3815 processor with 2GB DDR3L DRAM)
EMI/EMS
Meet CE/FCC class A
2 x CAN bus
TB-528CAN2
1 x SIM Card Socket
1 x mini-PCI-express slot
ACS-2702A User Manual
12
(units :mm)
Figure 2.1: Mainboard Dimensions
ACS-2702A User Manual
13
2.3 Jumpers and Connectors Location
Figure 2.2: Jumpers and Connectors Location- Board Top
Figure 2.3: Jumpers and Connectors Location- Board Bottom
ACS-2702A User Manual
14
2.4 Jumpers Setting and Connectors
1.
U2:
(FCBGA1170), onboard Intel Bay trail-I/M Processors.
Model
Processor
Number
PBF
Cores/Threads
TDP
Remarks
SBC-7111-E3845-2G
E3845
1.91GHz
4/4
10W
SBC-7111-E3845-4G
E3845
1.91GHz
4/4
10W
Option
SBC-7111-N2930-2G
N2930
1.83 up to
2.16GHz
4/4
4.5 /
7.5W
Option
SBC-7111-N2930-4G
N2930
1.83 up to
2.16GHz
4/4
4.5 /
7.5W
Option
SBC-7111-E3815-2G
E3815
1.46GHz
1/1
5W
Option
2.
H3/H4/H5/H6(option):
U2 Heat Sink Screw holes, four screw holes for intel Bay trail-I/M Processors Heat
Sink assemble.
3.
U3/U4/U5/U6:
(FBGA96)Onboard DDR3L Memory.
4.
5.
Model
Memory
SBC-7111-E3845-2G
2GB
SBC-7111-N2930-2G
2GB (option)
SBC-7111-E3815-2G
2GB (option)
SBC-7111-E3845-4G
4GB (option)
SBC-7111-N2930-4G
4GB (option)
S-422 (PIN6):
(Switch),ATX Power and Auto Power on jumper setting.
S-422(Switch)
Mode
Pin6 (Off)
ATX Power
Pin6 (On)
Auto Power on (Default)
BAT1 :
(1.25mm Pitch 1x2 Wafer Pin Header) 3.0V Li battery is embedded to provide
power for CMOS.
ACS-2702A User Manual
15
Pin#
Signal Name
1
VBAT
2
Ground
6.
SW1(NC):
(2.0mm Pitch 2x2 Pin Header),Reserve.
7.
BAT2(NC):
(2.0mm Pitch 1x8 Wafer Pin Header),Reserve.
8.
LED3/LED4(NC):
LED3:Reserve.
LED4:Reserve.
9.
DC_IN1:
(5.08mm Pitch 1x3 Pin Connector), DC9V~36V System power input connector.
10.
Pin#
Power input
1
DC+9V~36V
2
Ground
3
FG
Model
DC_IN1
SBC-7111-E3845-2G
180°Connector
SBC-7111-E3845-4G
180°Connector
SBC-7111-N2930-2G
180°Connector
SBC-7111-N2930-4G
180°Connector
SBC-7111-E3815-2G
180°Connector
SBC-7111-E3845P-2G
45°Connector
SBC-7111-E3845P-4G
45°Connector
BT1/BT2:
Power on/off button, They are used to connect power switch button. The two
pins are disconnected under normal condition. You may short them temporarily
to realize system startup & shutdown or awaken the system from sleep state.
ACS-2702A User Manual
16
11.
FAN1(option):
(2.54mm Pitch 1x3 Pin Header),Fan connector, cooling fans can be connected
directly for use. You may set the rotation condition of cooling fan in menu of
BIOS CMOS Setup.
Pin#
Signal Name
1
Ground
2
VCC
3
Rotation detection
Note:
Output power of cooling fan must be limited under 5W.
12.
VGA_PH1:
(CRT 2.0mm Pitch 2x6 Pin Header), Video Graphic Array Port, Provide 2x6Pin
cable to VGA Port.
Signal Name
Pin#
Pin#
Signal Name
CRT_RED
1
2
Ground
CRT_GREEN
3
4
Ground
CRT_BLUE
5
6
VGA_EN
CRT_H_SYNC
7
8
CRT_DDCDATA
CRT_V_SYNC
9
10
CRT_DDCCLK
Ground
11
12
Ground
VGA hot plug setting for Windows XP:
VGA1 (Pin Header)
Function
Pin4-Pin6 (Close)
VGA Simulation Disabled
Pin4-Pin6 (Open)
VGA Simulation Enabled
Use the 2.0mm jumper cap to close pin4 and pin6
13.
HDMI1:
(HDMI 19P Connector), High Definition Multimedia Interface connector.
ACS-2702A User Manual
17
14.
JP6:
(2.0mm Pitch 2x2 Pin Header), LVDS jumper setting.
15.
JP6
Function (CN1)
Pin1-Pin2 (Close)
Single channel LVDS
Pin1-Pin2 (Open)
Dual channel LVDS (Default)
Pin3-Pin4 (Close)
8/24 bit (Default)
Pin3-Pin4 (Open)
6/18 bit
U18:
AT24C02-DIP8,The EEPROM IC(U18)is the set of LVDS resolution. If you need
other resolution settings, please upgrade U18 data.
Model
LVDS resolution
SBC-7111-E3845-2G
SBC-7111-E3845-4G
SBC-7111-N2930-2G
SBC-7111-E3845-4G
SBC-7111-E3815-2G
1280*1024 (Default)
800*480 (option)
800*600 (option)
1024*768 (option)
1920*1080 (option)
……
16.
INVT1:
(2.0mm Pitch 1x6 wafer Pin Header), Backlight control connector for LVDS.
Pin#
Signal Name
1
+DC12V
2
+DC12V
3
Ground
4
Ground
5
BKLT_EN_OUT
6
BKLT_CTRL
ACS-2702A User Manual
18
17.
CN1:
(1.25mm Pitch 2x20 Connector, DF13-40P), for 18/24-bit LVDS output connector,
fully supported by Parad PS8625(DP to LVDS), the interface features dual
channel 24-bit output. Low Voltage Differential Signaling, A high speed, low
power data transmission standard used for display connections to LCD panels.
Function
Signal Name
Pin#
Pin#
Signal Name
12V_S0
2
1
12V_S0
BKLT_EN_OUT
4
3
BKLT_CTRL
Ground
6
5
Ground
LVDS_VDD5
8
7
LVDS_VDD5
LVDS_VDD3
10
9
LVDS_VDD3
Ground
12
11
Ground
LA_D0_P
14
13
LA_D0_N
LA_D1_P
16
15
LA_D1_N
LA_D2_P
18
17
LA_D2_N
LA_D3_P
20
19
LA_D3_N
LA_CLKP
22
21
LA_CLKN
LB_D0_P
24
23
LB_D0_N
LB_D1_P
26
25
LB_D1_N
LB_D2_P
28
27
LB_D2_N
LB_D3_P
30
29
LB_D3_N
LB_CLKP
32
31
LB_CLKN
Ground
34
33
Ground
LVDS
18.
LVDS
USB3
(JP4 open)
USB3
(JP4 open)
USB3_P
36
35
USB3_N
5V_S5_USB
38
37
5V_S5_USB
Power LED
PWR_LED+
40
39
Ground
Power LED
JP4:
(2.0mm Pitch 2x2 wafer Pin Header), USB3(CN1) or Touch jumper setting.
JP4
Function
USB3 (CN1)
Touch (TCH1)
Close 3-4 (default)
-
Yes
Open 3-4 (option)
Yes
-
Open 1-2 (default)
19.
Function
-
TCH1:
(2.0mm Pitch 1x6 wafer Pin Header), internal Touch controller connector.
ACS-2702A User Manual
19
20.
21.
Pin#
Signal Name
1
SENSE
2
X+
3
X-
4
Y+
5
Y-
6
GND_EARCH
JP1:
(2.0mm Pitch 2x3 Pin Header), COM1 jumper setting, pin 1~6 are used to select
signal out of pin 9 of COM1 port.
JP1 Pin#
Function
Close 1-2
COM1 RI (Ring Indicator) (default)
Close 3-4
COM1 Pin9: DC+5V
(option)
Close 5-6
COM1 Pin9: DC+12V
(option)
S_232:
(Switch), COM1 jumper setting, it provides selectable RS232 or RS422 or RS485
serial signal output.
Function
22.
S_232 Pin#
RS232 (Default)
ON: Pin1, Pin2, Pin3, Pin4
RS422 (option)
OFF: Pin1, Pin2, Pin3, Pin4
RS485 (option)
OFF: Pin1, Pin2, Pin3, Pin4
S_422:
(Switch), COM1 setting, it provides selectable RS232 or RS422 or RS485 serial
signal output.
Function
S_422 Pin#
RS232 (Default)
OFF: Pin1, Pin2, Pin3, Pin4, Pin5
RS422 (option)
ON: Pin1, Pin2, Pin3, Pin4, Pin5
RS485 (option)
ON: Pin1, Pin2, Pin3, Pin4, Pin5
S-422
Mode
Pin6 (Off)
ATX Power
Pin6 (On)
Auto Power on (Default)
ACS-2702A User Manual
20
23.
COM1:
(Type DB9M), Rear serial port, standard DB9 Male serial port is provided to
make a direct connection to serial devices. COM1 port is controlled by pins
No.1~6 of JP1, select output Signal RI or 5V or 12V, for details, please refer to
description of JP1 and S_232 and S_422 setting.
RS232 (Default)
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP1 select Setting (RI/5V/12V)
BIOS Setup:
Advanced/F81216SEC Super IO Configuration/Serial Port 1 Configuration 【RS-232】
RS422 (option)
Pin#
Signal Name
1
422_RX+
2
422_RX-
3
422_TX-
4
422_TX+
5
Ground
6
NC
7
NC
8
NC
9
NC
BIOS Setup:
Advanced/F81216SEC Super IO Configuration/Serial Port 1 Configuration 【RS-422】
ACS-2702A User Manual
21
RS485 (option)
Pin#
Signal Name
1
NC
2
NC
3
485-
4
485+
5
Ground
6
NC
7
NC
8
NC
9
NC
BIOS Setup:
Advanced/F81216SEC Super IO Configuration/Serial Port 1 Configuration 【RS-485】
24.
25.
JP2:
(2.0mm Pitch 2x3 Pin Header), COM2 jumper setting, pin 1~6 are used to select
signal out of pin 9 of COM2 port.
JP2 Pin#
Function
Close 1-2
COM2 RI (Ring Indicator) (default)
Close 3-4
COM2 Pin9: DC+5V
(option)
Close 5-6
COM2 Pin9: DC+12V
(option)
COM2:
(Type DB9M),Rear serial port, standard DB9 Male serial port is provided to
make a direct connection to serial devices.
Pin#
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP2 select Setting (RI/5V/12V)
ACS-2702A User Manual
22
26.
LED1,LED2 (option) :
LED1: LED STATUS. Green LED for Motherboard Standby Power Good status.
LED2: LED STATUS. Green LED for Touch Power status.
27.
SATA_P:
(2.5mm Pitch 1x2 box Pin Header), One onboard 5V output connector are
reserved to provide power for SATA devices.
Pin#
Signal Name
1
+DC5V
2
Ground
Note:
Output current of the connector must not be above 1A.
28.
SATA2:
(SATA 7Pin), SATA Connectors, one SATA connector are provided, with transfer
speed up to 3.0Gb/s.
29.
SATA1:
(SATA 7Pin+15Pin), SATA Connectors, one SATA connector are provided, with
transfer speed up to 3.0Gb/s.
30.
SD1:
(SD card slot), Secure Digital Memory Card socket.
31.
MPCIE1:
(Socket 52Pin), mini PCIe socket, it is located at the top, it supports mini PCIe
devices with USB2.0 and LPC and SMBUS and PCIe signal. MPCIe card size is
30x50.95mm.
32.
H1/H2:
MPCIE1 SCREW HOLES, H1and H2 for mini PCIE card (30mmx50.95mm)
assemble.
33.
F_AUDIO1:
(2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662-VD
codec is used to provide high-quality audio I/O ports. Line Out can be connected
to a headphone or amplifier. Line In is used for the connection of external audio
ACS-2702A User Manual
23
source via a Line in cable. MIC is the port for microphone input audio.
34.
Signal Name
Pin#
Pin#
Signal Name
+5V
1
2
GND_AUD
LINE-OUT-L
3
4
LINE-OUT-R
FRONT_JD
5
6
LINE1_JD
LINE_IN-L
7
8
LINE-IN-R
MIC-IN-L
9
10
MIC-IN-R
GND-AUD
11
12
MIC1_JD
LINE_OUT1:
(Diameter 3.5mm Jack), HD Audio port, An onboard Realtek ALC662-VD codec is
used to provide high quality audio I/O ports. Line Out can be connected to a
headphone or amplifier.
35.
USBCON1:
USB0/USB1:(Double stack USB type A), Rear USB connector, it provides up to
two USB2.0 port, High-speed USB 2.0 allows data transfers up to 480 Mb/s,
support USB full-speed and low-speed signaling.
Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A.
If the external USB device current exceeds 1.5A, please separate connectors
into different Receptacle.
36.
LAN1/LAN2:
LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M
RJ-45 Ethernet ports are provided. Used intel 82574L chipset, LINK LED (green)
and ACTIVE LED (yellow) respectively located at the left-hand and right-hand
side of the Ethernet port indicate the activity and transmission state of LAN.
37.
BUZ1:
Onboard buzzer.
ACS-2702A User Manual
24
38.
CN2:
(DF13-30P Connector),For expand output connector, It provides eight GPIO,one
RS422 or RS485,one USB2.0,one Power on/off, one Reset.
Function
Signal Name
Pin#
Pin#
Signal Name
Function
5V
5V_S5
2
1
5V_S5
5V
SOC_GPIO10
GPIO_IN2
4
3
GPIO_IN1
SOC_SPIO09
SOC_GPIO26
GPIO_IN4
6
5
GPIO_IN3
SOC_GPIO17
SOC_GPIO05
GPIO_OUT2
8
7
GPIO_OUT1
SOC_GPIO04
SOC_GPIO08
GPIO_OUT4
10
9
GPIO_OUT3
SOC_GPIO06
Ground
12
11
Ground
485 or 422
485+_422TX+
14
13
485-_422TX-
485 or 422
RS422
422_RX+
16
15
422_RX-
RS422
NC
18
17
NC
NC
20
19
NC
5V_S0
22
21
HDD_LED+
HDD LED
5V_USB01
24
23
5V_USB01
USB2.0
USBDN1_P
26
25
USBDN1_N
Ground
28
27
FP_RST-
PWRBTN_ON
30
29
Ground
5V
USB2.0
Power auto on
RESET
COM5 BIOS Setup:
Advanced/IT8518Super IO Configuration/Serial Port 1 Configuration【RS-422】
Advanced/IT8518Super IO Configuration/Serial Port 1 Configuration【RS-485】
39.
EC_GPIO1:
(2.0mm Pitch 1X10 Pin Header),For expand connector, it provides eight GPIO.
Pin#
Signal Name
1
Ground
2
EC_GPIO1
3
EC_GPIO2
4
EC_GPIO3
5
EC_GPIO4
6
EC_GPIO5
7
EC_GPIO6
8
EC_GPIO7
9
EC_GPIO8
10
3.3V
ACS-2702A User Manual
25
40.
CN3:
(1.27mm Pitch 2X30 Female Header), for expand output connector, It provides
four GPIO, two USB 2.0,one PS/2 mouse, one PS/2 keyboard, two uart, one
PCIex1, one SMbus. connected to the TB-528 riser Card.
Function
Signal Name
Pin#
Pin#
Signal Name
5V_S5_USB
1
2
5V_S5_USB
5V_S5_USB
3
4
5V_S5_USB
USB23_OC
5
6
PSON_ATX-
Exp-USB2
USB2_DM
7
8
USB2_DP
Exp-USB2
Exp-USB3
USB3_DM
9
10
USB3_DP
Exp-USB3
Ground
11
12
Ground
PS/2 MS
PS2_MSCLK
13
14
PS2_MSDATA
PS/2 MS
PS/2 KB
PS2_KBCLK
15
16
PS2_KBDATA
PS/2 KB
COM4_RI
17
18
COM4_DCD-
COM4_TXD
19
20
COM4_RXD
COM4_DTR
21
22
RICOM4_RTS-
COM4_DSR
23
24
COM_CTS-
Ground
25
26
Ground
COM3_RI
27
28
COM3_DCD-
COM3_TXD
29
30
COM3_RXD
COM3_DTR
31
32
DSRCOM3_RTS-
COM3_DSR
33
34
DTRCOM3_CTS-
GPIO23
SOC_GPIO23
35
36
ICH_GPIO22
GPIO12
GPIO25
SOC_GPIO25
37
38
ICH_GPIO24
GPIO24
Ground
39
40
Ground
PCIE_TX0_DN
41
42
PCIE_TX0_DP
PCIE_RX0_DN
43
44
PCIE_RX0_DP
Ground
45
46
Ground
PCIE_REFCLK0_DN
47
48
PCIE_REFCLK0_DP
PCIE0_WAKE_N
49
50
PLTRST_3P3_N
SMBUS
SMB_CLK_S0
51
52
SMB_DATA_S0
PCIE
PCIE_CLKREQ0_N
53
54
Ground
3P3V_S5
55
56
PWRBTN_ON-
3P3V_S5
57
58
3P3V_S5
12V_S0
59
60
12V_S0
COM4
(UART)
COM3
(UART)
PCIE
12V
ACS-2702A User Manual
Function
COM4
(UART)
COM3
(UART)
PCIE
SMBUS
Power Auto on
12V
26
Chapter 3
BIOS Setup
3.1 Operations after POST Screen
After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS
Setup.
After optimizing and exiting CMOS Setup, the POST screen displayed for the first time
is as follows and includes basic information on BIOS, CPU, memory, and storage
devices.
3.2 BIOS Setup Utility
Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu
containing system summary information will appear.
ACS-2702A User Manual
27
3.3 Main Settings
System Time:
Set the system time, the time format is:
ACS-2702A User Manual
Hour :
0 to 23
Minute :
0 to 59
28
Second : 0 to 59
System Date:
Set the system date, the date format is:
Day: Note that the ‘Day’ automatically changes when you set the date.
Month: 01 to 12
Date:
01 to 31
Year:
1998 to 2099
3.4 Advanced Settings
3.4.1 ACPI Settings
Enable ACPI Auto Conf:
[Disabled]
[Enabled]
Enable Hibernation:
ACS-2702A User Manual
29
[Enabled]
[Disabled]
ACPI Sleep State:
[S3 (Suspend to RAM) ]
[Suspend Disabled]
Lock Legacy Resources:
[Disabled]
[Enabled]
3.4.2 F81216SEC Super IO Configuration
Super IO chip F81216SEC
Serial Port 1 Configuration
UART1 Mode Selection:
[RS-232]
[RS-485]
[RS-422]
Serial Port 2 Configuration
Change Settings
[Auto]
Serial Port 3 Configuration
Change Settings
[Auto]
Serial Port 4 Configuration
Change Settings
[Auto]
3.4.3 IT8518 Super IO Configuration
Super IO chip IT8518/IT8519
Serial Port 1 Configuration
Backlight PWM Controller(COM5):
[RS-485]
[RS-422]
Serial Port 2 Configuration (COM6)
Change Settings
[Auto]
3.4.4 Intel(R)Smart Connect Technology
ISCT Support
[Disabled]
[Enabled]
ACS-2702A User Manual
30
3.4.5 Serial Port Console Redirection
COM0
Console Redirection
[Disabled]
[Enabled]
Console Redirection Settings
Legacy Console Redirection
Legacy Console Redirection settings
Serial Port for Out-of-Band Management/
Windows Emergency Management Services (EMS)
Console Redirection
[Disabled]
[Enabled]
Console Redirection Settings
3.4.6 CPU Configuration
Socket 0 CPU Information
Intel(R) Atom(TM) CPU E3845 @ 1.91GHz
CPU Signature
Microcode Patch
Max CPU Speed
30679
901
1910 MHz
Mix CPU Speed
Processor Cores
Intel HT Technology
Intel HT-X Technology
L1 Data Cache
L1 Code Cache
L2 Cache
L2 Cache
500 MHz
4
Not Supported
Supported
24KB x 4
32KB x 4
1024KB x 2
Not Present
CPU Thermal configuration
CPU Speed
64-bit
Hyper-Threading:
1918 MHz
Supported
[Enabled]
[Disabled]
ACS-2702A User Manual
31
Limit CPUID Maximum:
[Disabled]
[Enabled]
Execute Disable Bit:
[Enabled]
[Disabled]
Intel Virtualization Technology:
[Enabled]
[Disabled]
Power Technology
[Energy Efficient]
[Disabled]
[Custom]
3.4.7 PPM Configuration
CPU C State Report
[Enabled]
[Disabled]
Max CPU C-state
[C7]
[C6]
[C1]
SOix
[Disabled]
[Enabled]
3.4.8 Thermal Configuration Parameters
3.4.9 IDE Configuration
Serial-ATA(SATA)
[Enabled]
[Disabled]
SATA Test Mode
[Disabled]
[Enabled]
SATA Speed Support
[Gen2]
[Gen1]
ACS-2702A User Manual
32
SATA ODD Port
[No ODD]
[Porto ODD]
[Port1 ODD]
[Disabled]
SATA Mode
[AHCI Mode]
[IDE Mode]
Serial-ATA Port 0
[Enabled]
[Disabled]
SATA Port0 Hotplug
[Disabled]
[Enabled]
Serial-ATA Port 1
[Enabled]
[Disabled]
SATA Port1 Hotplug
[Disabled]
[Enabled]
SATA Port0
Not Present
SATA Port1
Not Present
3.4.10 Miscellaneous Configuration
ACS-2702A User Manual
33
High Precision Timer
[Enabled]
[Disabled]
Boot Timer with HPET Timer
[Disabled]
[Enabled]
PCI Express Dynamic Clock Gating
[Disabled]
[Enabled]
OS Selection
Use the OS Selection option to select an operating system for the system.
Note:
Users must go to this item to select the OS mode before installing corresponding OS
driver, otherwise problems will occur when installing the driver.
3.4.11 LPSS & SCC Configuration
LPSS & SCC Configuration
SCC Configuration
SCC eMMC Support
SCC eMMC 4.5 DDR50 Support
SCC eMMC 4.5 HS200 Support
eMMC Secure Erase
SCC SDIO Support
SCC SD Card Support
SDR25 Support for SDCard
SDR50 Support for SDCard
MIPI HSI Support
[ACPI Mode]
[eMMC AUTO MODE]
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[Disabled]
LPSS Configuration
LPSS DMA #1 Support
LPSS DMA #2 Support
LPSS I2C #1 Support
LPSS I2C #2 Support
LPSS I2C #3 Support
LPSS I2C #4 Support
ACS-2702A User Manual
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
34
LPSS I2C #5 Support
[Enabled]
LPSS I2C #6 Support
LPSS I2C #7 Support
NFC
Touch Pad
I2C touch Device Address
LPSS HSUART #1 Support
LPSS HSUART #2 Support
LPSS PWM #1 Support
LPSS PWM #2 Support
LPSS SPI Support
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
3.4.12 System Component
3.4.13 Network Stack Configuration
Network Stack
3.4.14 CSM Configuration
CSM Support
CSM16 Module Version
GateA20 Active
Option ROM Messages
Boot option filter
[Disabled]
[Enabled]
07.76
[Upon Request]
[Always]
[Force BIOS]
[Keep Current]
[UEFI and Legacy]
[Legacy only]
[UEFI only]
Network
[UEFI]
[Do not launch]
[Legacy]
Storage
[UEFI]
[Do not launch]
[Legacy]
Video
[Legacy]
[UEFI]
ACS-2702A User Manual
35
[Do not launch]
Other PCI devices
[UEFI]
[Do not launch]
[Legacy]
3.4.15 SDIO Configuration
3.4.16 USB Configuration
USB Configuration
USB Module Version 8.11.02
USB Devices:
1 keyboard, 1 Mouse,2 Hubs
Legacy USB Support:
[Enabled]
[Disabled]
XHCI Hand-off:
[Enabled]
[Disabled]
EHCI Hand-off:
[Disabled]
[Enabled]
USB Mass Storage Driver Support
[Enabled]
[Disabled]
USB hardware delays and time-outs:
USB transfer time-out:
[20 sec]
[10 sec]
[5 sec]
[1 sec]
Device reset time-out:
[20 sec]
[10 sec]
[30 sec]
[40 sec]
Device power-up delay
[Auto]
[Manual]
ACS-2702A User Manual
36
3.4.17 Platform Trust Technology
3.4.18 Security Configuration
3.5 Chipset Settings
3.5.1 Host Bridge
►Intel IGD Configuration
►IGD – LCD Control
Force Lid Status
BIA
ALS Support
IGD Flat Panel
Pannel Scaling
[On]
[Off]
[Auto]
[Disabled]
[Auto]
[Auto]
►Memory Frequency and Timing
►Graphics Power Management Control
Memory Information
Total Memory
4096 MB(DDR3L)
Memory Slot0
4096 MB(DDR3L)
DIMM#1
Not Present
ACS-2702A User Manual
37
Max TOLUD
[Dynamic]
[2GB]
[2.25GB]
[2.5GB]
[2.75GB]
[3GB]
3.5.2 South Bridge
►Azalia HD Audio
►USB Configuration
USB OTG Support
USB VBUS
ACS-2702A User Manual
[Disabled]
[On]
XHCI Mode
USB2 Link Power Management
USB 2.0(EHCI) Support
USB EHCI debug
USB Per Port Control
USB Port 0
USB Port 1
USB Port 2
[Smart Auto]
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
USB Port 3
[Enabled]
38
3.6 Security Settings
3.6.1 Administrator Password
3.6.2 User Password
Type the password with up to 20 characters and then press Enter key. This will
clear all previously typed CMOS passwords. You will be requested to confirm the
password. Type the password again and press Enter key. You may press Esc
key to abandon password entry operation.
To clear the password, just press Enter key when password input window pops
up. A confirmation message will be shown on the screen as to whether the password
ACS-2702A User Manual
39
will be disabled. You will have direct access to BIOS setup without typing any
password after system reboot once the password is disabled.
Once the password feature is used, you will be requested to type the password each
time you enter BIOS setup. This will prevent unauthorized persons from changing
your system configurations.
Also, the feature is capable of requesting users to enter the password prior to system
boot to control unauthorized access to your computer. Users may enable the feature
in Security Option of Advanced BIOS Features. If Security Option is set to System, you
will be requested to enter the password before system boot and when entering BIOS
setup; if Security Option is set to Setup, you will be requested for password for
entering BIOS setup.
3.7 Boot Settings
Setup Prompt Timeout
Bootup Numlock State
[1]
[On]
[off]
Quiet Boot
[Disabled]
ACS-2702A User Manual
40
[Enabled]
Fast Boot
[Disabled]
[Enabled]
Boot Option Priorities
Boot Option #1
Hard Drive BBS Priorities
Sets the system boot order
[SATA PM:*** … ]
Boot Option #1
SATA PM:***…
******
Disabled
3.8 Save & Exit Settings
Save Changes and Exit
Save & Exit Setup save Configuration and exit ?
[Yes]
[No]
ACS-2702A User Manual
41
Discard Changes and Ext
Exit Without Saving Quit without saving?
[Yes]
[No]
Save Changes and Reset
Save & reset Save Configuration and reset?
[Yes]
[No]
Discard Changes and Reset
Reset Without Saving Reset without saving?
[Yes]
[No]
Save Changes
Save Setup Values Save configuration?
[Yes]
[No]
Discard Changes
Load Previous Values Load Previous Values?
[Yes]
[No]
Restore Defaults
Load Optimized Defaults Load optimized Defaults?
[Yes]
[No]
Save user Defaults
Save Values as User Defaults Save configuration?
[Yes]
[No]
Restore user Defaults
Restore User Defaults Restore User Defaults?
[Yes]
[No]
Launch EFI Shell from filesystem device
WARNING Not Found
[ok]
Reset System with ME disable ModeMEUD000
ME will runs into the temporary disable mode, Ignore if ME Ignition
FWMEUD001.
ACS-2702A User Manual
42
Chapter 4
Installation of Drivers
This chapter describes the installation procedures for software and drivers under the
windows 7. The software and drivers are included with the motherboard. The
contents include Intel chipset driver, VGA driver, LAN drivers, Audio driver, USB 3.0
Driver, Com Driver Installation instructions are given below.
Important Note:
After installing your Windows operating system, you must install first the Intel
Chipset Software Installation Utility before proceeding with the installation of
drivers.
ACS-2702A User Manual
43
4.1 Intel(R) AtomTM SoC Chipset
To install the Intel chipset driver, please follow the steps below.
Step 1. Select Intel (R) AtomTM SoC Chipset from the list
Step 2. Click Next to setup program.
ACS-2702A User Manual
44
Step 3. Read the license agreement. Click Yes to accept all of the terms of the
license agreement.
Step 4. Click Next to continue.
ACS-2702A User Manual
45
Step 5. Click Next.
Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove
any installation media from the drives.
ACS-2702A User Manual
46
4.2 Intel(R) VGA Chipset
To install the VGA drivers, follow the steps below to proceed with the installation.
Step 1.Select Intel(R) VGA Chipset
Step 2. Click Automatically run WinSAT and enable the Windows Aero desktop
theme(if supported). Click Next.
ACS-2702A User Manual
47
Step 3. Read license agreement.
Click Yes.
Step 4. Click Next.
ACS-2702A User Manual
48
Step 5. Click Install.
Step 6. Click Install.
ACS-2702A User Manual
49
Step 7. Click Next.
Step 8. Click Yes, I want to restart this computer now. Then click Finish.
ACS-2702A User Manual
50
4.3 Intel(R) LAN Driver
To install the Intel (R) LAN driver, please follow the steps below.
Step 1. Select Intel(R) 82574L LAN Driver from the list.
Step 2. . Click Next.
ACS-2702A User Manual
51
Step 3. Read license agreement. Click I accept the terms in the license agreement.
Click Next.
Step 4. Click Next to continue.
ACS-2702A User Manual
52
Step 5. Click Install to begin the installation.
Step 6. Click Finish to exit the wizard.
ACS-2702A User Manual
53
4.4 Realtek ALC662 HD Audio Driver Installation
To install the Realtek ALC662 HD Audio Driver, please follow the steps below.
Step 1. Select Realtek AL662 HD Audio Driver from the list
Step 2. Click Next to continue.
ACS-2702A User Manual
54
Step 3. Click Yes, I want to restart my computer now. Click Finish to complete the
installation.
ACS-2702A User Manual
55
4.5 USB 3.0 Driver
To install the USB 3.0 Driver, please follow the steps below.
Step 1. Select USB 3.0 Driver from the list
Step 2. Click Next to continue.
ACS-2702A User Manual
56
Step 3. Read the license agreement. Then click Yes to continue.
Step 4. Click Next to continue.
ACS-2702A User Manual
57
Step 5. Click Next to continue.
Step 6. Select Yes, I want to restart this computer now. Then click Finish to complete
the installation.
ACS-2702A User Manual
58
4.6 Com Driver
To install the Com Driver, please follow the steps below.
Step 1. Select Com Driver from the list
Step 2. Click Next to continue.
ACS-2702A User Manual
59
Step 3. Click install to begin the installation.
Step 4. Click Finish to complete the installation.
ACS-2702A User Manual
60
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement