Pfaff passport 3.0 manual

Owner’s manual
I
This household sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety precautions should always be followed, including
the following:
Read all instructions before using this household sewing machine. Keep the instructions at a suitable place close to the machine. Make sure to hand them over if the machine is given to a third
party.
DANGER – To reduce the risk of electric shock:
• A sewing machine should never be left unattended when plugged in. Always unplug this
sewing machine from the electric outlet immediately after using and before cleaning, removing
covers, lubricating or when making any other user servicing adjustments mentioned in the
instruction manual.
WARNING – 7RUHGXFHWKHULVNRIEXUQVÀUHHOHFWULFVKRFNRULQMXU\WR
person:
• Do not allow to be used as a toy. Close attention is neccesary when this sewing machine is used
by or near children.
• Use this sewing machine only for its intended use as described in this manual. Use only
attachments recommended by the manufacturer as contained in this manual.
• Never operate this sewing machine if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return the sewing machine
to the nearest authorized dealer or service center for examination, repair, electrical or mechanical
adjustment.
• Never operate the sewing machine with any air openings blocked. Keep ventilation openings of
the sewing machine and foot control free from the accumulation of lint, dust, and loose cloth.
‡.HHSÀQJHUVDZD\IURPDOOPRYLQJSDUWV6SHFLDOFDUHLVUHTXLUHGDURXQGWKHVHZLQJPDFKLQH
needle.
• Always use the proper needle plate. The wrong plate can cause the needle to break.
• Do not use bent needles.
‡'RQRWSXOORUSXVKIDEULFZKLOHVWLWFKLQJ,WPD\GHÁHFWWKHQHHGOHFDXVLQJLWWREUHDN
• Wear safety glasses.
‡6ZLWFKWKHVHZLQJPDFKLQHRII´µZKHQPDNLQJDQ\DGMXVWPHQWLQWKHQHHGOHDUHDVXFKDV
threading needle, changing needle, threading bobbin, or changing presser foot, etc.
• Never drop or insert any object into any opening.
• Do not use outdoors.
‡'RQRWRSHUDWHZKHUHDHURVROVSUD\SURGXFWVDUHEHLQJXVHGRUZKHUHR[\JHQLVEHLQJ
administrated.
‡7RGLVFRQQHFWWXUQDOOFRQWUROVWRWKHRII´µSRVLWLRQWKHQUHPRYHSOXJIURPRXWOHW
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• The foot control is used to operate the machine. Avoid placing other objects on the foot control.
• Do not use the machine if it is wet.
• If the LED lamp is damaged or broken, it must be replaced by the manufacturer or it's service
DJHQWRUDVLPLODUO\TXDOLÀHGSHUVRQLQRUGHUWRDYRLGDKD]DUG
• If the supply cord connected with the foot control is damaged, it must be replaced by the
PDQXIDFWXUHURULWVVHUYLFHDJHQWRUDVLPLODUO\TXDOLÀHGSHUVRQLQRUGHUWRDYRLGDKD]DUG
• This sewing machine is provided with double insulation. Use only identical replacement parts.
6HHLQVWUXFWLRQVIRU6HUYLFLQJRI'RXEOH,QVXODWHG$SSOLDQFHV
SAVE THESE INSTRUCTIONS
)RU(XURSHRQO\
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
7KHQRLVHOHYHOXQGHUQRUPDORSHUDWLQJFRQGLWLRQVLVOHVVWKDQG%$
The machine must only be used with foot control of type "C-9002" manufactured by CHIENHUNG
TAIWAN., LTD.
For outside Europe:
7KLVVHZLQJPDFKLQHLVQRWLQWHQGHGIRUXVHE\SHUVRQVLQFOXGLQJFKLOGUHQZLWKUHGXFHG
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the sewing machine by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the
sewing machine.
7KHQRLVHOHYHOXQGHUQRUPDORSHUDWLQJFRQGLWLRQVLVOHVVWKDQG%$
The machine must only be used with foot control of type "C-9002" manufactured by CHIENHUNG
TAIWAN., LTD.
SERVICING OF DOUBLE INSULATED PRODUCTS
In a double-insulated product, two systems of insulation are provided instead of grounding. No
ground means is provided on a double-insulated product, nor should a means for grounding
EHDGGHGWRWKHSURGXFW6HUYLFLQJRIDGRXEOHLQVXODWHGSURGXFWUHTXLUHVH[WUHPHFDUHDQG
NQRZOHGJHRIWKHV\VWHPDQGVKRXOGEHGRQHRQO\E\TXDOLÀHGVHUYLFHSHUVRQQHO5HSODFHPHQW
parts for a double-insulated product must be identical to those parts in the product. A doubleLQVXODWHGSURGXFWLVPDUNHGZLWKWKHZRUGV¶'28%/(,168/$7,21·RU¶'28%/(,168/$7('·
2
Congratulations!
Congratulations on purchasing your new PFAFF® sewing machine. As a sewing enthusiast, you
have acquired a machine that features the very latest in both design and technology, enabling you to
transform your creative ideas into reality.
Before you start, please spend some time reading this owner’s manual. You will soon discover how
to maximize the use of your machine. Our authorized PFAFF® dealer will of course also be pleased
to advise you as well.
Your PFAFF® passport™ VHZLQJPDFKLQHZLOOGHÀQLWHO\HQDEOH\RXWRH[SHULHQFHDWRWDOO\QHZ
dimension of sewing!
Table of contents
Introduction
4
Machine overview ..............................................................4
Accessories ...........................................................................5
Presser feet..........................................................................6
Stitch overview ....................................................................7
Preparations
9
Unpacking.............................................................................9
Connect to the power supply .......................................9
Pack away after sewing ...................................................9
Free arm ............................................................................. 10
Leveling the machine base plate ............................. 10
Thread cutter .................................................................... 10
Spool pins .......................................................................... 10
Threading the machine ................................................ 11
Needle threader ...............................................................12
Threading for twin needle..............................................12
Bobbin winding ............................................................... 13
Inserting the bobbin ...................................................... 14
IDT™ system (integrated dual feed) ....................... 14
Presser foot pressure .................................................... 15
Thread tension ................................................................. 15
Needles ............................................................................... 16
Changing the needle ..................................................... 17
Lowering feed dogs........................................................ 17
Presser foot lift ................................................................ 17
Changing the presser foot .......................................... 17
Buttons......................................................................... 18-19
Warning messages/sound .......................................... 20
Sewing
21
Select a stitch ................................................................... 21
Stitch adjustments ......................................................... 21
Sewing techniques ......................................................... 22
Three-step zigzag stitch ..................................................22
Buttonholes.......................................................................22
Sew on a button ...............................................................23
Darning and mending ....................................................24
Sewing hems in heavy fabric .........................................24
Quilting .............................................................................25
Blindhem...........................................................................26
Sewing in zippers ............................................................26
Maintenance
27
Cleaning the machine................................................... 27
Replacing the stitch plate ........................................... 27
Troubleshooting............................................................... 28
Intellectual property ...................................................... 29
Note: The machine models will be referred to as simply 3.0 and 2.0 in this manual.
3
Introduction
Machine overview
18
1
19
20
2
17
3
15
4
5
6
7
8
16
9
10
11
12
13
14
Front side
1. Threading slots
11. Needle screw
2.
Thread cutter
12. Needle thread guide
3.
LED lights
13. Presser foot bar and presser foot holder
4.
Built-in needle threader
14. Presser foot
5.
Buttonhole lever
15. Free arm
6.
Needle bar
16. Accessory tray
7.
Stitch plate
17. Speed control lever
8.
Bobbin cover
18. Buttons and LED display
9.
Lower thread guide
19. Handwheel
10. Presser foot lift
4
20. Pull-out stitch overview
Top parts
21. Presser foot pressure dial
21 22
23
24
25
22. Thread guides
23. Spool caps
24. Hole for auxiliary spool pin
25. Bobbin winder lever and
bobbin spindle
26. Take-up lever
27. Thread tension discs
28. Bobbin winder tension disc
29. Thread tension dial
26
27 28 29
31
Rear side
30. Main switch, connectors for power
cord and foot control
31. Handle
32. Presser foot lift
33. IDT™ system
32
34. Slide for lowering the feed dogs
33
30
34
Accessories
Included accessories
35. Bobbins (5) (#416475801)
35
36
37
38
36. Felt pad
37. Screwdriver for needle plate
38. Multi-purpose tool
39
40
41
39. Spool cap, large (2)
40. Spool cap, small
41. Seam ripper & brush (as one)
42. Edge guide
43. Auxiliary spool pin
42
43
Included accessories not in picture
• Foot control
•
Power cord
•
Needles
•
Hard cover
5
Presser feet
Standard presser foot 0A with IDT™ system (shown as
display, attached on the machine upon delivery)
in the
This foot is used mainly for straight stitching and zigzag stitching with a
stitch length longer than 1.0 mm.
Fancy stitch foot 1A with IDT™ system (shown as
in the display)
This foot is used for decorative stitches. The groove on the underside of the
IRRWLVGHVLJQHGWRÁRZVPRRWKO\RYHUWKHVWLWFKHV
Fancy stitch foot 2A (shown as
in the display)
When sewing decorative stitches or short zigzag stitches and other utility
stitches with less than 1.0 mm stitch length, use this foot. The groove on the
XQGHUVLGHRIWKHIRRWLVGHVLJQHGWRÁRZVPRRWKO\RYHUWKHVWLWFKHV
Blindhem foot 3 with IDT™ system (shown as
in the display)
This foot is used for blindhem stitches. The toe on the foot guides the
fabric. The red guide on the foot is designed to ride along the fold of the
hem edge.
Zipper foot 4 with IDT™ system
This foot can be snapped on either the right or the left of the needle,
making it easy to sew close to both sides of the zipper teeth. Move the
needle position to the right or left to sew closer to zipper teeth.
One step Buttonhole foot 5B (shown as
in the display)
This foot has a space in the back to set the size of the buttonhole. The
PDFKLQHZLOOVHZDEXWWRQKROHWRÀWWKDWEXWWRQVL]H
Important: Make sure that the IDT™ system is disengaged when using presser foot 2A, 5B.
6
Stitch overview
8WLOLW\VWLWFKHV
Stitch
3.0
2.0
00
01
01
02
02
03
03
04
04
05
05
06
06
07
07
-
08
-
09
08
10
09
11
10
12
11
13
12
14
13
15
14
16
15
17
16
18
17
19
18
20
21
= Engage IDT™ system
Name
Description
Straight stitch
For seaming and topstitching. Select from 29 different needle
positions.
Stretch triple straight
stitch
Reinforced seam. Topstitching.
Zigzag stitch
5HLQIRUFHVHDPVFOHDQÀQLVKVWUHWFKVHZLQJODFHLQVHUWLRQ
Z-zigzag stitch
Appliqué, couching, eyelets.
Stretch triple zigzag stitch Elastic stitch for decorative hems or topstitching.
Three-step zigzag stitch
Sewing elastic, darning, patching.
Honeycomb stitch
Decorative stitch for stretch fabrics and hems. Also used with elastic
thread in the bobbin.
Bridging stitch
Joining fabrics and quilt batting, decorative stitch for quilting,
hemstitching.
Foundation elastic stitch
Joining stitch for undergarments, terry cloth, leather, bulky fabrics
where overlapping the seams.
Crosshem stitch
Elastic decorative hem for stretch fabrics.
Blindhem stitch
Sewing blindhems on woven fabrics.
Elastic blindhem stitch
Sewing blindhems on stretch fabrics.
Stretch tricot stitch
Sewing seams on stretch fabrics.
Closed overlock
Seam and overcast stretch fabrics in one step.
Standard overcast
Seam and overcast stretch fabrics in one step with reinforced edge.
Closed overlock
Seam and overcast stretch fabrics in one step.
Standard buttonhole
Basic buttonhole for blouses, shirts and jackets. Also for pillowcases.
Rounded buttonhole
Buttonhole for garments.
Eyelet buttonhole
Tailors buttonhole for jackets and trousers.
Stretch buttonhole
Buttonhole for stretch fabrics.
19
Button sewing
Sew on buttons or tacking.
20
Programmable darning
stitch
Darning holes or damaged fabric.
7
Quilt stitches
= Engage IDT™ system
Stitch
3.0
22 *
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
2.0
21 *
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
3.0
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
2.0
38
39
40
41
42
43
44
-
-
45
46
-
-
-
47
-
-
Stitch
6WLWFKRQLVVHZQZLWKPRQRÀODPHQWQHHGOHWKUHDGDQGLQFUHDVHGWKUHDGWHQVLRQWRFUHDWH
a handlook effect.
Needle art stitches
= Engage IDT™ system
Stitch
3.0
56
57
58
59 ** 60 ** 61 **
62
63
64
65
66
2.0
-
-
-
48 ** 49 ** 50 **
-
-
-
-
-
** Stitches 59, 60 and 61 (48, 49 and 50 on model 2.0) are meant to be
sewn with a wing needle for a special effect.
Satin stitches
Stitch
3.0
67
68
69
70
71
72
73
74
75
76
77
78
79
2.0
51
52
-
-
-
-
63
-
53
-
-
54
-
Decorative stitches
Stitch
3.0
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
2.0
55
56
57
-
58
59
60
-
61
-
62
64
65
-
66
67
3.0
96
97
98
99
2.0
-
68
69
70
Stitch
Note: Place stabilizer under your fabric for best results when sewing decorative stitches.
8
Preparations
Unpacking
3ODFHWKHER[RQDVWHDG\ÁDWVXUIDFH/LIW
the machine out of the box, remove the outer
packaging and lift off the machine carrying
case.
2.
Remove all outer packing material and the
plastic bag.
Note: Your PFAFF® passport™ sewing machine is
adjusted to provide the best stitch result at normal room
temperature. Extreme hot and cold temperatures can
affect the sewn result.
&RQQHFWWRWKHSRZHUVXSSO\
$PRQJWKHDFFHVVRULHV\RXZLOOÀQGWKHSRZHU
cord and the foot control.
1RWH&RQVXOWDTXDOLÀHGHOHFWULFLDQLILQGRXEWDVWR
how to connect the machine to the power source. Unplug
the power cord when the machine is not in use.
For this sewing machine, foot control model C-9002
manufactured by CHIENHUNG TAIWAN., LTD
must be used.
1. Connect the foot control cord to the front
socket on the bottom right side of the machine
(A).
2.
Connect the power cord to the rear socket on
the bottom right side of the machine (B). Plug
the cord into the wall socket.
3.
Press the ON/OFF switch to ON to turn on
power and light (C).
C
B
A
3DFNDZD\DIWHUVHZLQJ
1.
Switch the main switch off.
Note: After switching off, residual power may still
remain in the machine. This may cause the light to stay
on for a few seconds while the power is consumed. This
LVQRUPDOEHKDYLRUIRUDQHQHUJ\HIÀFLHQWDSSOLDQFH
2.
Unplug the cord from the wall socket and then
from the machine.
3.
Unplug the foot control cord from the machine.
Wind the cord around the foot control for easy
storage.
4.
Place all accessories in the accessory tray. Slide
the tray on to the machine around the free arm.
5. Place the foot control in the space above the
free arm.
6.
For the USA and Canada
This sewing machine has a polarized plug (one
blade wider than the other). To reduce the risk
RIHOHFWULFVKRFNWKLVSOXJLVLQWHQGHGWRÀWLQD
polarized outlet only one way. If the plug does
QRWÀWIXOO\LQWKHRXWOHWUHYHUVHWKHSOXJ,ILW
VWLOOGRHVQRWÀWFRQWDFWDTXDOLÀHGHOHFWULFLDQWR
install the proper outlet. Do not modify the plug
in any way.
Put on the hard cover.
9
Free arm
To use the free arm, slide off the accessory tray.
When attached, a hook keeps the accessory tray
securely attached to the machine. Remove the tray
by sliding it to the left.
Leveling the machine base plate
To make sure your machine stands steadily on
your sewing surface you can adjust the base plate
height. Turn the base plate adjusting screw (A)
by hand. Turn clockwise to lower and counterclockwise to raise the base plate.
A
Thread cutter
B
To use the thread cutter, pull the thread from back
to front as shown (B).
Spool pins
Your machine has two spool pins, a main spool
pin and an auxiliary spool pin. The spool pins
are designed for many types of thread. The main
spool pin is adjustable and can be used both in a
horizontal position (the thread reels off the spool)
and a vertical position (the thread spool rotates).
The horizontal position can be used for most
sewing and embroidery threads, and the vertical
position can be used for many specialty threads.
Horizontal position
Place a spool cap and the thread spool on the spool
pin. Make sure that the thread reels over the top
and slide on the second spool cap.
Use a spool cap slightly larger than the thread
spool.
Large spool cap
For narrow thread spools, use a smaller spool cap
in front of the spool. For large thread spools, use a
larger spool cap in front of the spool.
7KHÁDWVLGHRIWKHVSRROFDSVKRXOGEHSUHVVHG
ÀUPO\DJDLQVWWKHVSRRO7KHUHVKRXOGEHQRVSDFH
between the spool cap and the thread spool.
Small spool cap
10
Vertical position
Raise the spool pin to the vertical position. Slide
on the large spool cap and place a felt pad under
the thread spool. This is to prevent the thread from
reeling off too fast.
A
Do not place a spool cap on top of the spool pin as
that would prevent the spool from rotating.
$X[LOLDU\VSRROSLQ
The auxiliary spool pin is used when winding a
bobbin thread from a second spool of thread or for
a second spool when sewing with a twin needle.
Main spool pin in vertical position.
Insert the auxiliary spool pin into the hole at the
top of the machine (A). Slide on a large spool cap
and place a felt pad under the thread spool.
Threading the machine
Make sure that the presser foot is raised and the
needle is in its highest position.
3ODFHWKHWKUHDGRQWKHVSRROSLQDQGÀWWKH
appropriately sized spool cap.
2.
Pull the thread into the right thread guide (B)
from front to back and the left thread guide (C)
from back to front. Pull the thread between the
tension discs (D).
3.
Thread down through the right-hand
threading slot and then upwards through the
left-hand threading slot.
4.
Bring the thread from the right into the take-up
lever (E) and down in the left-hand threading
slot, into the lower thread guide (F) and to the
needle thread guide (G).
5.
Thread the needle.
C
Auxiliary spool pin.
B
G
E
F
D
11
Needle threader
The needle threader allows you to thread the needle
automatically. The needle must be in its highest
position to use the built-in needle threader. Press the
needle up/down button to make sure the needle is
fully raised.
We also recommend lowering the presser foot.
1.
Use the handle to pull the needle threader all
the way down. The threader hook (F) swivels
through the needle eye.
2.
Place the thread from the back over the hook (G)
and under the thread hook (F).
3.
Let the needle threader gently swing back. The
hook pulls the thread through the needle eye
and forms a loop behind the needle. Pull the
thread loop out behind the needle.
Note: The needle threader is designed to be used for size 70120 needles. You cannot use the needle threader for size 60
needles or smaller, wing needles or twin needles. There are
also some optional accessories that require manual threading
of the needle.
When threading the needle manually, make sure that the
needle is threaded from front to back.
G
F
Note: When you are using a twin needle, you might need to
reduce the stitch width to prevent damage of the twin needle,
stitch plate or presser foot. How much you need to reduce it
depends on the stitch position, the stitch width and/or the size
of the twin needle.
A
B
Threading for twin needle
Replace the sewing needle with a twin needle. Make
sure that the presser foot is raised and the needle is
in its highest position.
3ODFHWKHWKUHDGRQWKHVSRROSLQDQGÀWWKH
appropriately sized spool cap. Insert the auxiliary
spool pin. Slide on a large spool cap and a felt
pad. Place the second thread on the spool pin.
2.
Pull the thread into the right thread guide (A)
from front to back and the left thread guide (B)
from back to front. Pull both threads between
the tension discs (C).
3.
Thread down through the right-hand threading
slot and then upwards through the left-hand
threading slot.
4.
Bring the threads from the right into the take-up
lever (D) and down in the left-hand threading
slot. Place the threads into the lower thread
guide (E). Place one thread into the slot on the
left side of the needle thread guide (F) and the
other thread into the slot on the right side of
the needle thread guide (G). Make sure that the
threads do not become twisted together.
5.
Thread the needles.
Note: The weight and irregular surface of specialty threads,
like metallics, can cause increased tension on the thread.
Reducing the tension will prevent needle breakage.
12
D
C
E
F
G
A
B
Bobbin winding
1.
Place the thread spool on the spool pin in
horizontal position. Slide a spool cap tightly
against the spool.
2.
Place the thread into the thread guide (A) from
front to back. Pull the thread clockwise around
the bobbin winder tension disc (B).
3.
Thread through the hole in the bobbin (C) from
the inside to the outside.
4.
Place an empty bobbin on the bobbin spindle.
5.
Push the bobbin lever to the right to wind.
7KHOHWWHUV63ÁDVKRQWKH/('GLVSOD\'
Press the foot control to wind the bobbin.
C
D
When the bobbin is full, release the foot
control. Push the bobbin lever to the left.
Remove the bobbin and cut the thread.
13
Inserting the bobbin
Make sure that the needle is fully raised and the
machine is turned off before inserting or removing
the bobbin. Open the bobbin cover by pushing the
release button to the right (A). Remove the cover
(B).
1.
Insert the bobbin in the bobbin case with the
thread running in a counterclockwise direction.
2.
Pull the thread through the slit (C).
:LWKDÀQJHUKHOGJHQWO\RQWRSRIWKHEREELQ
draw the thread at the arrow markings into the
stitch plate thread guide from (C) to (D).
4.
Pull the thread at the arrow markings into the
stitch plate thread guide from (D) to (E).
5.
To cut off excess thread pull thread back over
the cutting off blade at point (E).
6.
Replace the bobbin cover.
1
2
B
A
3
4
D
E
C
IDT™V\VWHPLQWHJUDWHGGXDO
feed)
For sewing any fabric precisely, PFAFF®
passport™ sewing machine provides the ideal
solution: the integrated dual feed, IDT™ system. As
on industrial machines, the IDT™ system feeds the
fabric from the top and bottom at the same time.
The fabrics are fed precisely. On light fabrics such
as silk or rayon the dual feed prevents puckering
of the seam. The even feeding action also ensures
perfect matching of checked and striped fabrics.
The IDT™ system keeps all layers of quilt projects
aligned to prevent shifting of the layers.
Engaging the IDT™V\VWHP
Important: For all work with the IDT™ system, use
presser feet with the center back cut-out (F).
Raise the presser foot. Press the IDT™ system down
until it engages.
Disengaging the IDT™V\VWHP
Raise the presser foot. Hold the IDT™ system with
WZRÀQJHUVDWWKHULEEHGDQNOH3XOOWKHIDT™
system down, then pull it away from you to release
the IDT™ system slowly upward.
14
F
Presser foot pressure
The presser foot pressure has been pre-set to the
standard value ”N”. In most cases, you do not need
to adjust the presser foot pressure. When using
specialty techniques, or when sewing on very light
or heavy fabric, adjusting the pressure can improve
the result.
For very light fabrics, loosen the pressure by
turning the dial counterclockwise.
Note: If the dial is turned counterclockwise too much, it
could come off. If this happens, simply replace the dial
and turn it clockwise until it stays in place.
For heavy fabric, tighten the pressure by turning
the dial clockwise.
Note: If the dial is turned clockwise until it comes to a
stop, it has reached the maximum pressure available.
Do not try to turn the dial any further!
Thread tension
To set the thread tension, turn the dial on top of the
machine. Depending on the fabric, batting, thread,
etc, the tension may need to be adjusted.
For the best stitch appearance and durability, make
sure the needle thread tension is correctly adjusted.
For general sewing, the threads evenly meet
between the two layers of fabric.
If the bobbin thread is visible on the top side of
the fabric, the needle thread tension is too tight.
Reduce the needle thread tension.
If top thread is visible on the underside of the
fabric, the needle thread tension is too loose.
Increase the needle thread tension.
For decorative stitches and buttonholes, the top
thread should be visible on the underside of the
fabric.
Make a few tests on a scrap piece of the fabric you
are going to sew and check the tension.
15
Needles
The sewing machine needle plays an important
role in successful sewing. Use only quality needles.
We recommend needles of system 130/705H.
The needle package included with your machine
contains needles of the most frequently used sizes.
8QLYHUVDOQHHGOH$
Universal needles have a slightly rounded point
and come in a variety of sizes. For general sewing
in a variety of fabric types and weights.
6WUHWFKQHHGOH%
Stretch needles have a special scarf to eliminate
VNLSSHGVWLWFKHVZKHQWKHUHLVDÁH[LQWKHIDEULF
)RUNQLWVVZLPZHDUÁHHFHV\QWKHWLFVXHGHVDQG
leathers. Marked with a yellow band.
(PEURLGHU\QHHGOH&
Embroidery needles have a special scarf, a slightly
rounded point and a slightly larger eye to avoid
damage to thread and materials. Use with metallic
and other specialty threads for embroidery and
decorative sewing. Marked with a red band.
A
'HQLPQHHGOH'
Denim needles have a sharp point to penetrate
WLJKWO\ZRYHQIDEULFVZLWKRXWGHÁHFWLQJWKHQHHGOH
)RUFDQYDVGHQLPPLFURÀEHUV0DUNHGZLWKDEOXH
band.
:LQJQHHGOHV(
The Wing needle has wide wings on the side of
the needle to poke holes in the fabric when sewing
HQWUHGHX[DQGRWKHUKHPVWLWFKHVRQQDWXUDOÀEHU
fabrics.
Note: Change the needle often. Always use a straight
needle with a sharp point (F).
A damaged needle (G) can cause skipped stitches,
breakage or snapping of the thread. A damaged needle
can also damage the stitch plate.
Do not use asymmetrical twin needles (H), since it may
damage your sewing machine.
16
F
G
H
B
C
D
E
Changing the needle
1.
Use the hole in the multi-purpose tool to hold
the needle.
2.
Loosen the needle screw. Use the screwdriver
if necessary.
3.
Remove the needle.
4.
Insert the new needle, using the multi-purpose
tool. Push the new needle upwards with the
ÁDWVLGHDZD\IURP\RXXQWLOLWZLOOJRQR
further.
5.
Tighten the needle screw as tight as it will go.
Lowering feed dogs
A
You can lower the feed dogs by moving the switch
at the back of the free arm to the left. Move the
switch to the right if you wish to raise the feed
dogs.
Note: The feed dogs will not raise immediately when the
lever is switched. Turn the handwheel one full turn or
start sewing to re-engage the feed dogs.
Presser foot lift
The presser foot is lowered or raised with the
presser foot lift (A). If you are sewing on heavy
fabric or several layers of fabric, the presser foot
can be raised higher to make it easier to place the
fabric underneath the presser foot.
Changing the presser foot
Remove presser foot
Press the presser foot downwards until it
disengages from the presser foot holder.
Attach presser foot
Place the presser foot under the presser foot holder
(B), lining up the notch (C) with the pins (D).
D
Lower the presser foot lift and the presser foot will
engage in the presser foot holder.
Note: Check that the presser foot is properly attached by
raising the presser foot lift.
B
C
D
D
17
Buttons passport™ 3.0
8
7
6
4
2
5
1
5HYHUVH
If you press the reverse button while sewing, the
machine sews in reverse for as long as you keep the
button pressed.
Reverse is also used when sewing the darning
stitch.
6WDUWVWRS
Press this button to start or stop the machine
without using the foot control. Press the button
once to start and press it again to stop.
6SHHGFRQWUROOHYHU
The speed control lever sets the maximum sewing
speed. To increase sewing speed, slide the lever up,
to decrease sewing speed, slide the lever down.
7KUHDGVQLSV
Press this button when you are not sewing and the
machine cuts the top and bobbin threads. Press this
EXWWRQZKLOHVHZLQJDQGWKHPDFKLQHZLOOÀQLVK
the stitch, perform a tie-off and cut the top and
bobbin threads.
,PPHGLDWHWLHRII7LHRII
For immediate tie-off press the button while
sewing. The machine sews tie-off stitches
immediately and stops automatically.
To set the machine to perform a tie-off at the end
of a stitch, press the button before starting to sew.
The LED light next to the button becomes lit. After
sewing the desired length of stitching, press the
reverse button while actively sewing. The machine
will complete the current stitch, tie-off and stop
automatically.
18
10
9
3
Note: The tie-off function is not available for stitches
16-21.
1HHGOHXSGRZQ
Press this button to move the needle up or down.
The setting of the needle stop position is changed
at the same time.
You can also tap the foot control to raise or lower
the needle.
6WLWFKOHQJWK
Increase or decrease the stitch length using the “+”
and “-” buttons.
6WLWFKZLGWKRUVWLWFKSRVLWLRQLQJ
Increase or decrease the stitch width using the “+”
and “-” buttons.
For straight stitches, use the “+” and “-” buttons to
change the stitch position.
Note: There are 29 needle positions available. 3.5 on the
display is the center position.
,QIREXWWRQ
Press this button to show the presser foot
recommendation on the LED display. If a dot is
visible in the lower right corner of the screen, the
IDT™ system should be engaged.
6WLWFKVHOHFWLRQ
Press a combination of the 0 to 9 buttons to select
the stitch represented by that number.
Buttons passport™ 2.0
8
7
6
4
2
5
1
9
3
5HYHUVH
If you press the reverse button while sewing, the
machine sews in reverse for as long as you keep the
button pressed.
1HHGOHXSGRZQ
Press this button to move the needle up or down.
The setting of the needle stop position is changed
at the same time.
Reverse is also used when sewing the darning
stitch.
You can also tap the foot control to raise or lower
the needle.
6WDUWVWRS
Press this button to start or stop the machine
without using the foot control. Press the button
once to start and press it again to stop.
6WLWFKOHQJWK
Increase or decrease the stitch length using the “+”
and “-” buttons.
6SHHGFRQWUROOHYHU
The speed control lever sets the maximum sewing
speed. To increase sewing speed, slide the lever up,
to decrease sewing speed, slide the lever down.
,QIREXWWRQ
Press this button to show the presser foot
recommendation on the LED display. If a dot is
visible in the lower right corner of the screen, the
IDT™ system should be engaged.
,PPHGLDWHWLHRII7LHRII
For immediate tie-off press the button while
sewing. The machine sews tie-off stitches
immediately and stops automatically.
6WLWFKZLGWKRUVWLWFKSRVLWLRQLQJ
Increase or decrease the stitch width using the “+”
and “-” buttons.
For straight stitches, use the “+” and “-” buttons to
change the stitch position.
Note: There are 29 needle positions available. 3.5 on the
display is the center position.
6WLWFKVHOHFWLRQ
Press a combination of the 0 to 9 buttons to select
the stitch represented by that number.
To set the machine to perform a tie-off at the end
of a stitch, press the button before starting to sew.
The LED light next to the button becomes lit. After
sewing the desired length of stitching, press the
reverse button while actively sewing. The machine
will complete the current stitch, tie-off and stop
automatically.
Note: The tie-off function is not available for stitches
15-20.
19
Warning messages/sound
Main motor overloaded
Your sewing machine can get overloaded when
sewing on heavy fabrics e.g,. the thread gets
twisted or jammed or the hand wheel axle cannot
move. A monotone beep sound is heard and
WKHOHWWHUV(/ÁDVKRQWKH/('GLVSOD\3OHDVH
UHIHUWRWKHWURXEOHVKRRWLQJRQSDJHWRÀQGD
recommended solution. When the problem has
been solved, the machine will continue to sew.
Note: When sewing, if the thread gets jammed inside
the hook preventing the needle from moving and you
continue pressing the foot control, the security switch
will stop the machine completely. Restart the sewing
machine by switching the ON/OFF switch to the OFF
position and then ON again.
Note: If the problem is still not solved, please contact
your local authorized PFAFF® dealer.
Bobbin winding position
When the bobbin lever is pushed to the right, the
OHWWHUV63ÁDVKRQWKH/('GLVSOD\
If you press any button, a beep will inform you to
push the bobbin winder spindle to the left, sewing
position.
Note: You cannot sew in bobbin winding position.
B
Machine sound
It is possible to turn off the sound on the machine
buttons. Press the immediate tie-off button (A)
while turning on the machine.
Select between the audio on or off by touching the
stitch width “+” or “–” buttons (B).
Touch “-” to turn off the audio and the display will
show “0”. Touch “+” to turn on the audio and the
display will show “1”.
Press the immediate tie-off button again to return
to sewing mode.
20
A
Sewing
When the machine is turned on, straight stitch 00
(01 on 2.0) is selected by default.
Select a stitch
Press a combination of the 0 to 9 buttons to select
the stitch represented by that number.
6WLWFKDGMXVWPHQWV
Your machine will automatically set the length
(A) and width/positioning (B) for the selected
stitch. You can make your own adjustments on the
selected stitch.
The setting changes only affect the selected
stitch, and will be reset to default when another
stitch is selected. The changed settings are not
automatically saved when turning your machine
off.
Press "+" or "-" once next to the setting you wish to
change. The set value will be indicated in numbers
on the display and the LED light (C) next to the
setting control lights up. Change the set value by
pressing the "+" or "–" button when the LED light
is lit.
B
A
C
When trying to exceed minimum or maximum
settings a warning sound will be heard.
1RWH7KHGHIDXOWYDOXHRIDVHWWLQJZLOOÁDVKRQWKH
display when scrolling through the setting values.
21
Sewing techniques
Three-step zigzag stitch
Stich number 05 (06 on 2.0) can be used to overcast
raw edges. Make sure the needle pierces the fabric
on the left side and overcasts the edge on the right
side.
Stich number 05 (06 on 2.0) can also be used as an
elastic stitch to allow seams to stretch when sewing
knit fabrics.
Buttonholes
Your machine’s buttonholes are specially adjusted
for different kinds of fabric and garments. Look
DWWKHVWLWFKWDEOHRQSDJHLQWKLVERRNWRÀQG
descriptions of each buttonhole.
The fabric should be interfaced and/or stabilized
where buttonholes are to be sewn.
One step Buttonhole Foot 5B
1. Mark the the position of the buttonhole on
your garment.
2.
Attach buttonhole foot 5B and pull out the
button holder plate. Insert the button. The
button will determine the length of the
buttonhole.
3.
Make sure that the thread is pulled though the
hole in the presser foot and placed under the
foot.
4.
Select the buttonhole you want to sew and
adjust the length as desired.
Note: Always sew a test buttonhole on a scrap piece of
fabric.
5.
Position your garment under the presser foot
so that the marking on the fabric is aligned
with the center of the buttonhole foot.
6.
Lower the buttonhole lever all the way down,
and push it away from you.
7.
Hold the end of the upper thread and start
sewing. The buttonholes are sewn from the
front of the presser foot to the back.
8.
Once the machine has sewn the buttonhole,
raise the presser foot.
22
&RUGHGEXWWRQKROH6WUHWFKIDEULFV
When sewing buttonholes in stretch fabrics we
recommend cording the buttonhole to increase the
stability and to keep the buttonhole from stretching
out.
1.
Loop a piece of heavy thread or pearl cotton
RYHUWKHÀQJHUDWWKHEDFNRIWKHEXWWRQKROH
foot 5B. Pull the thread tails under the foot,
WRZDUGWKHIURQWWKHQVHFXUHDURXQGWKHÀQJHU
at the front of the foot.
2.
Stitch a buttonhole. The satin buttonhole
columns will stitch over the cord.
:KHQWKHEXWWRQKROHLVÀQLVKHGOLIWWKHFRUG
RIIWKHÀQJHUDQGSXOORXWWKHVODFN
4.
Cross the cord in front of the needle and thread
cord ends into a large needle, pull to the wrong
side and knot ends before cutting excess.
5.
Use the seam ripper to carefully open the
buttonhole.
Sew on a button
1.
To sew on a button, remove the presser foot
and select the button sewing stitch, number 20
(19 on 2.0).
2.
Lower the feed dogs.
3.
Place the button under the presser foot holder.
Turn the handwheel slowly to make sure the
holes in the button are aligned with the swing
of the needle and the width is appropriate for
the actual button. If necessary, adjust the stitch
width to accommodate the width between the
holes.
4.
You can increase or decrease the number of
stitches that will fasten the button on the fabric
in steps of two, using the stitch length buttons
(A). The set number of stitches is indicated on
the display. 6 stitches is default.
5.
Start to sew. The machine will sew the
program for you and then tie-off and stop.
A
Note: Use the multi-purpose tool to create a thread
shank for your button. You can also use the Sew-on
Button Foot #820 473-96, available as an optional
accessory.
23
Darning and mending
Darning a small hole or a tear before it becomes
larger can save a garment. Choose a thread in a
color as close to your garment as possible.
1.
Place fabric or stabilizer in position under the
hole or tear in your garment.
2.
Select stitch number 21 (20 on 2.0), the darning
stitch.
3.
Start sewing above the hole and over it.
4.
Once you have sewn across the hole, press
the reverse button (A) to set the length of the
stitch. Your sewing machine will automatically
complete the stitch.
5.
By default, the machine will be set to repeat
the same size darning square, just continue
sewing.
To set a different length of the darning stitch,
select the stitch again and continue with steps 3
and 4 above.
Note: Darning stitches can also be sewn using the
buttonhole foot 5B. Set the length of the darning stitch
by pulling out the button holder plate and lower the
buttonhole lever to sew the stitch.
6HZLQJKHPVLQKHDY\IDEULF
When sewing over seams in extra heavy fabric or
a blue jeans hem, the foot can tip as the machine
climbs over the seam. Use the multi-purpose tool to
balance the height of the presser foot as you sew.
One side of the multi-purpose tool is thicker than
the other. Use the side that suits the thickness of
the seam best.
24
A
Quilting
A quilt usually consists of three layers, two layers
of fabric with a layer of batting sandwiched
between.
To sew three layers together, you have a wide
variety of stitches and techniques to choose from.
Stitch-in-the-Ditch
Use the Fancy stitch foot 1A with IDT™ system.
Stitching in the ditch means using the guide on the
presser foot to follow the seams in the quilt blocks.
Begin by pin basting your quilt through all layers
with safety pins, starting from the center of your
quilt and working out. Place a pin every 6-8 inches
(15-20 cm).
Note: You can also use the optional Stitch-in-Ditch w
IDT™ system presser foot #820 925- 096.
&UD]\TXLOWVWLWFKLQJ
Embellish your quilt with decorative stitches.
The stitches can be sewn in a coordinating or
contrasting color. Decorative threads like rayon
embroidery or heavy cotton threads are sometimes
used.
Free-motion stippling
Free-motion stippling not only keeps the top,
batting and backing together, but it also adds
texture and interest to your quilt.
Free-motion stippling is done with the feed
dogs lowered. You move the fabric manually to
determine the stitch length.
5.
Begin near the center of your quilt. Take one
stitch and pull the bobbin thread to the top of
the quilt. Take a few stitches right next to one
another to lock the threads.
6.
Now move the quilt so that your stitching
creates swirls. The stitching should not cross
over itself, and should travel in a meandering
motion.
Handlook quilting
1. Baste the completed quilt top to the batting and
backing.
2.
Thread the needle with an invisible
PRQRÀODPHQWWKUHDG8VHFRQWUDVWLQJRU
matching rayon or cotton thread in the bobbin.
3.
Select the handlook quilt stitch, number 22 (21
on 2.0), and increase the needle thread tension
to 7-9.
Lower the feed dogs.
4.
Snap on the recommended presser foot 0A.
Pin baste your quilt layers and prepare your
quilt as explained under Stitch-in-the-Ditch
above.
5.
Engage the IDT™ system.
6.
When you sew the stitch you should only see
your bobbin thread. Fine adjust the needle
thread tension as needed to produce the
desired effect.
1.
Set your sewing machine for stippling by
selecting the straight stitch, number 00 (01 on
2.0).
2.
Attach the optional Open Toe Free-Motion foot
#820 988-096.
3.
4.
Tip! Practice stippling on scraps of fabric and batting.
Sewing with a constant speed will help to keep the
stitches even.
25
Blindhem
The blindhem stitch, number 10 (09 on 2.0), is used
to make invisible hems on skirts, trousers and
home decorating. Use foot number 3 with IDT™
system.
1.
Finish the edge of the hem.
2.
Fold and press the hem allowance to the wrong
side.
3.
Fold the hem back on itself so approximately
µFPRIWKHÀQLVKHGHGJHH[WHQGV
beyond the fold. The wrong side of your
project should now be facing up.
4.
Place the fabric under the presser foot so that
the fold runs along edge guide A.
5.
When the needle swings into the fold it should
catch a small amount of fabric. If the stitches
are visible on the right side, adjust edge guide
A by turning adjusting screw B until the stitch
that catches the hem just barely shows.
Elastic blindhem stitch
The elastic blindhem stitch, number 11 (10 on 2.0),
is especially suitable for stretchy fabrics, because
the zigzag in the stitch lets the stitch stretch. The
KHPLVÀQLVKHGDQGVHZQDWWKHVDPHWLPH7KHUHLV
QRQHHGWRÀQLVKWKHUDZHGJHÀUVWRQPRVWNQLWV
Sewing in zippers
There are different ways to sew in zippers. Follow
the directions included with your pattern for best
results.
For all types of zippers it is important to sew close
to the teeth of the zipper. The zipper foot 4 can be
snapped to the presser foot bar on the left or right,
depending on how you will insert your zipper.
Set the stitch position so the needle enters close to
the edge of the zipper teeth by using one of the 29
needle positions available for the straight stitch. If
the presser foot is attached on the right side, the
needle must only be moved to the right. If the foot
is attached on the left, the needle must only be
moved to the left.
26
B
A
Blindhem stitch, number
10 (09 on 2.0)
Elastic blindhem stitch,
number 11 (10 on 2.0)
Maintenance
Cleaning the machine
To keep your sewing machine operating well, clean
it often. No lubrication (oiling) is needed.
Wipe the exterior surface of your machine with a
soft cloth to remove any dust or lint built up.
C
C
Cleaning the bobbin area
Note: Raise the needle, lower the feed dogs and
turn off the machine.
B
A
Remove the presser foot. Push the bobbin cover
release button (A) to the right and remove
the bobbin cover (B) and the bobbin. Use the
screwdriver to remove the two screws (C) in the
stitch plate. Lift up the stitch plate.
Clean the feed dogs and the bobbin area with the
brush found with the accessories.
Cleaning under the bobbin area
Clean the area under the bobbin case after
sewing several projects or any time you notice an
accumulation of lint in the bobbin case area.
Remove the bobbin case by lifting it up and to the
right. Clean the area with the brush or with a dry
cloth.
Put the bobbin case back into the hook race so that
WKHWLSÀWVLQWRWKHVWRSSHU'
Note: Do not blow air into the bobbin case area. The
dust and lint will be blown into your machine.
Replacing the stitch plate
With the feed dogs lowered, replace the stitch plate
and insert and tighten the two stitch plate screws.
Replace the bobbin cover.
D
27
Troubleshooting
,QWKLVWURXEOHVKRRWLQJJXLGH\RXZLOOÀQGVROXWLRQVWRWKHSUREOHPV\RXPD\KDYHZLWK\RXUPDFKLQH
For further information please contact your local authorized PFAFF® dealer.
Problem/cause
General problems
5HPHG\
Fabric does not move?
Make sure that the feed dogs are not lowered.
The needle breaks?
Insert needle correctly, see page 17.
The machine will not sew?
Attach correct needle for the fabric.
Check that all plugs are securely plugged into the
machine and into the wall socket.
The sewing machine function buttons do not
respond to touch?
Push bobbin winder lever to sewing position.
The sockets and function buttons on the machine
can be sensitive to static electricity. If the buttons
do not respond to touch, turn the machine OFF and
then ON again. If the problem persists, contact your
local authorized PFAFF® dealer.
The machine skips stitches
Did you insert the needle properly?
Insert needle correctly, see page 17.
Did you insert a wrong needle?
Use needle system 130/705 H.
Is the needle bent or blunt?
Insert a new needle.
Did you thread the machine properly?
Check how the machine is threaded.
Is the correct presser foot used?
Attach correct presser foot.
Is the needle too small for the thread?
Make sure the needle is correct for the thread and
fabric.
Needle thread breaks
Did you insert the needle properly?
Insert needle correctly, see page 17.
Did you insert a wrong needle?
Use needle system 130/705 H.
Is the needle bent or blunt?
Insert a new needle.
Did you thread the machine properly?
Check how the machine is threaded.
Is the needle too small for the thread?
Change the needle to the proper size for the thread.
Are you using poor thread with slubs or thread
which has become dry?
Is a correct spool cap used?
Change to a new higher quality thread purchased
from an authorized PFAFF® dealer.
Attach a spool cap of the right size for the actual
thread spool.
Try a different spool pin position (vertical or
horizontal).
Change the stitch plate.
Is the best spool pin position used?
Is the stitch plate hole damaged?
Bobbin thread breaks
Did you insert the bobbin properly?
Check the bobbin thread.
Is the stitch plate hole damaged?
Change the stitch plate.
Is the bobbin area clean?
Clean lint from bobbin area.
Is the bobbin wound correctly?
Wind a new bobbin.
28
The seam has uneven stitches
Is the thread tension correct?
Check needle thread tension and the threading.
Are you using too thick or slubbed thread?
Change the thread.
Is the bobbin thread evenly wound?
Check bobbin winding.
Is a correct needle used?
Insert a proper needle correctly, see page 17.
7KHPDFKLQHGRHVQRWIHHGRUIHHGVLUUHJXODUO\
Did you thread the machine properly?
Check how the machine is threaded.
Has sewing lint collected between the feed dogs?
Remove the stitch plate and clean the feed dogs
with a brush.
The main motor becomes overloaded
Has the thread become twisted or jammed in the
bobbin case area or the feed dogs?
Remove the stitch plate and clean threads and lint
from the feed dogs and bobbin case area.
Re-thread the machine, both top and bobbin
threads.
We reserve the right to change the machine equipment and the assortment of
DFFHVVRULHVZLWKRXWSULRUQRWLFHRUPDNHPRGLÀFDWLRQVWRWKHSHUIRUPDQFHRUGHVLJQ
6XFKPRGLÀFDWLRQVKRZHYHUZLOODOZD\VEHWRWKHEHQHÀWRIWKHXVHUDQGWKHSURGXFW
,QWHOOHFWXDOSURSHUW\
PFAFF, PERFECTION STARTS HERE, PASSPORT and IDT (image) are trademarks of
KSIN Luxembourg II, S.ar.l.
Please note that on disposal, this product must be
safely recycled in accordance with relevant National
legislation relating to electrical/electronic products. Do
not dispose of electrical appliances as unsorted muncipal waste, use separate collection facilities. Contact
your local government for information regarding the
collection systems available. When replacing old appliances with new ones, the retailer may be legally obligated to take back your old appliance for disposal free
of charge.
,IHOHFWULFDODSSOLDQFHVDUHGLVSRVHGRILQODQGÀOOV
or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging
your health and well-being.
CE - Authorised Representative
VSM Group AB, SVP Worldwide
Drottninggatan 2, SE-56184, Huskvarna, SWEDEN
29
471 01 87-26B • English • InHouse • © 2015 KSIN Luxembourg II, S.ar.l. • All rights reserved • Printed in Germany on environmentally-friendly paper
www.pfaff.com