QUICK SETUP GUIDE
Screws (ST4 × 12F) × 3
Screws (M4 × 16) × 2
Screws (ST3 × 16C) × 2
Switch to DTV Radio program
Analog/ Digital TV
Start video recorder
• If the item is not specified in the accessories list, it should be provided by customer.
Mute the sound
Media player mode
INSTALLING THE STAND
Select among the different signal sources.
CH + -
Select the channel.
VOL + -
Adjust the volume.
Turn on the TV or put the TV in standby mode.
Select Audio language
Red, Green, Yellow and Blue
are used in media mode
Exit: Exit all menu display
Display the main menu
/ Back menu display
Enter or confirm the operation,
TV Side View
Channel Up/ Channel Down
Picture mode selecting
Volume Up/ Volume Down
PB/CB Component Cable PB/CB
To return to the last view program
Text, Size, Reveal, Hold, Index, Subpage
(refer to teletext function)
Video recorder list
Equipment with A/V jacks
TV Bottom Panel
Play/ Pause, Stop, etc.
are used in media mode
Connect a USB 2.0 device port for browsing photos, listening music and watching
• Press [◄ / ►] button to select USB in the Source menu, then press [OK] button
1,2,...numbers: For direct channel access
Time shift in DTV Mode
Sound mode selecting
Electronic program guide
FOR ILLUSTRATION ONLY.
Powering up or down the TV requires several seconds of processing time.
Do not rapidly turn the TV on/off as abnormal operation may occur.
Display the subtitle
content of the signal
Fast access to your saved
1. Use the screws (ST4x12F) X 3 to fix the Neck and Base.
2. Attach the stand to the TV set as shown in the picture.
3. Use the screws (M4x16) X 2 and screws (ST3x16C) X 2 to fix the stand tightly.
Set the sleep time
Audio select button
Carefully place your TV facedown on a soft, cushioned surface to prevent
damage to the TV or scratching to the screen.
Open the OSD menu.
Batteries: AAA × 2
Available source selection
Quick Setup Guide
Remote sensing Window
Red light up in standby mode. Blue light up in power on mode.
Receive remote signals from the remote control.
Do not put anything near the sensor, as its function may be affected.
Connect an HDMI cable or Component in/AV IN Adapter from an external A/V
equipment. No sound connection is needed for HDMI to HDMI connection. If the
device signal resolution does not match the specification table you need to change the
setting of device according to the table. Please consult your device user manual for
• To select the HDMI / Component / AV
Press [Source] button, when the list of Input Source appears, press [▲/▼] to select
the source [HDMI] / [Component] / [AV], then press [OK] to connect.
HDMI / COMPONENT IN / AV IN
CHANGE THE BATTERIES
1. Slide open the battery cover on the back of the remote control.
2. Install two AAA size (1.5V) batteries. Match the “+” and “-” signs on the batteries to the
signs on the battery compartment.
3. Close the battery cover.
Connect an antenna or cable TV to this jack.
HDMI (High-Definition Multimedia Interface)provides
uncompressed video data and digital audio data.
Connect to a DVD player, Digital Set-Top-Box, or other A/V
devices with component (YPBPR) video and audio output jacks.
Component audio Jack share AV IN audio Jack.
Connect to the composite video and audio (L/R) output jacks
on external video devices.
Product image is only for reference, actual product may vary in appearance.
AV&COMP AUDIO IN
INSTALLING A WALL-MOUNT BRACKET
PC/DVI AUDIO IN
Dispose of your batteries in a designated disposal area. Do not throw the
batteries into fire.
Do not mix battery types or combine used batteries with new ones.
Remove depleted batteries immediately to prevent battery acid from leaking
into the battery compartment.
If you do not intend to use the remote control for a long time, remove the
The effective range of remote control is suggested in the figure below.
If you want to attach the TV to a wall-mount bracket (not provided),Make sure the TV
is laid face-down on a clean,safe, and cushioned surface.
Attach purchased bracket on the TV with the 4 screws (not provided) .
M4 x 20mm
To prevent internal damage to the TV and ensure the TV is mounted securely, be sure
to use fixing screws (Not provided) which are 7 mm to 9 mm in length when measured
from the attaching surface of the mounting hook.
Connect to an external digital audio device.
Turning the TV On for the First Time
VGA & AUDIO
Connect a VGA cable and an audio cable from the PC.
• To select the PC: Press [Source] button, when the list of In Source appears,
press [▲/▼] to select the source PC, then press [OK] to connect.
100 × 100
Follow instructions provided with the wall bracket.
If you are not sure of your ability to complete the installation, contact a
professional installer or service technician for assistance. The manufacturer is
not responsible for any damages or injuries that occur due to mishandling or
Be sure to use the provider spacers between the TV and the bracket when
attaching the mount.
AUDIO OUT Connect Headphone for audio out of the TV.
Connect an RF cable from the TV’s input called “ANT/CABLE IN” and to your TV
Press [◄ / ►] button to select the language to be used for menus and message.
Mode Setting: Press [◄ / ►] button to select mode.
Country: Press [◄ / ►] button to select the country you want to.
Auto Scan: Press [◄ / ►] button to select Mode: DTV+ATV, DTV, ATV.
the TV’s rear cover
Wall-mount screw size (mm)
Wall-mount hole pattern VESA (mm)
Video , MP3, JPEG play and software update.
6m 30° 30°6m
Connect to headphone for private listening.
ANT Connect an outdoor VHF/UHF antenna.
1. The maximum distance is 8
meters in front of the TV set.
2. The remote control is effective
within 30 Degrees of horizontal
angle, or 15 Degrees of vertical
angle at maximum distances of
Connect to a PC or other devices with a VGA interface.
Check the jacks' for position and type before making any
connections.Loose connections can result in image or color
problems. Make sure that all connections are tight and secure.
REMOTE CONTROL RANGE
1. Use a coaxial cable to connect the A/V device’s digital audio in jack to the TV’s
DIGITAL AUDIO OUT jack.
2. Plug the connected devices into the mains socket before switching on the TV.
3. Select the corresponding source from the TV.
Size with base (mm)
Size without base (mm)
Gross Weight (kg)
Net Weight (kg)
(with base/without base)
Screen Diagonal Size
Sound Output (RMS)
1366 × 768
2.5 W + 2.5 W
220V - 240V
PAL B/G D/K, SECAM B/G D/K, DVB-T
Temperature: 5°C - 45°C
Humidity: 20% - 80% RH
Atmospheric pressure: 86 kPa - 106 kPa
640×480, 800×600, 1024×768, 1280×1024 60Hz
Attention： Excessive sound pressure from earphones and headphones can
cause hearing loss.
PC/DVI AUDIO IN
Features, appearance and specifications are subject to change without notice.
AC Power ON/OFF
you refer to the Trouble Shooting tips in the User Manual.
* Your assessment is very important for improving the work
of artificial intelligence, which forms the content of this project