User manual | User`s Manual VX-VEB160R4 [V2] Unpacking Information Introduction

User’s Manual
VX-VEB160R4 [V2]
Introduction
General Description
FCC Certifications
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at their own expense.
The VX-VEB160R4 [V2] converts
twisted pair. The device integrates
buildings over existing phones lines.
as an Ethernet Extender, allowing
beyond its limitation of 100 meters.
Ethernet to VDSL2 over
Ethernet functionality in
The device also functions
users to extend Ethernet
The VX-VEB160R4 [V2] port supports a maximum
symmetrical data transmission rate of up to 100/100 Mbps. The
device can transmit data at a maximum distance of up to 2000 ft.
It is ideal for point to point connections without the added
expense of having to rewire cables.
The extender features a ‘plug-n-play’ installation that does not
require additional software configuration.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received; including interference that may cause
undesired operation.
The cable specifications of the connection are listed as
following:
CE Mark Warning
The following diagrams represent the typical applications for the
VX-VEB160R4 [V2]
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 Class A for ITE, the
essential protection requirement of Council Directive
89/336/EEC on the approximation of the laws of the Member
States relating to electromagnetic compatibility.
•
•
•
10BASE-T, Category 3, 4 or 5 UTP/STP
100BASE-TX, Category 5 UTP/STP
Twisted-pair telephone wires
Our company has an on-going policy of upgrading its products
and it may be possible that information in this document is not
up-to-date. Please check with your local distributors for the
latest information. No part of this document can be copied or
reproduced in any form without written consent from the
company.
Trademarks: All trade names and trademarks are the properties
of their respective companies. Copyright © 2014. All Rights
Reserved.
Unpacking Information
Thank you for purchasing the VX-VEB160R4. Before installing,
please check that your package contains the following items.
1. One VX-VEB160R4 [V2]
2. One power adapter
3. One RJ-4 5 cable
Key Features
•
•
•
•
•
•
•
•
•
•
•
•
Complies with IEEE802.3 10BASE-T standard
Complies with IEEE802.3u 100BASE-TX standard
Complies with VDSL2 ITU-T G.993.2
Supports 1 RJ-45 port for Ethernet over VDSL2
Provides 4 RJ-45 ports for 10/100Mbps Ethernet.
Provides 1 Dip Switch for mode selection
Voice and Data function via the same telephone line
Maximum port bandwidth of 100Mbps/100Mbps
(downstream /upstream)
Supports Distances of up to 2,000ft.
Compact design (129.8 x 85 x 27mm)
LED indicators
External Power Adapter
The Front Panel
Use and Care
The device further extends Ethernet using a single twisted pair
of copper. It allows data services to be extended beyond
Ethernet capabilities and supports many multi-media
applications.
The Rear Panel
When deciding where to install the extender, please ensure that
the extender is accessible, that cables can easily be connected,
and that cabling is away from sources of electrical noise such as
radios, transmitters, power lines and fluorescent lighting
fixtures. In addition, please ensure that:
•
•
Dip Switch Settings
Water or moisture cannot enter the unit.
Airflow around the unit and through the vents in the
side of the case is not restricted (company recommend
that you provide a minimum of 1 inch clearance).
Pin 1: Mode selection between CO and CPE mode
To prolong the operational life of your units:
Pin 2: Reserved
LEDs Definition
•
•
Do not place objects on top of any unit or stack.
Do not obstruct any vents at the sides of the case.
Product Specifications
Installing and Using
VX-VEB160R4 [V2]
Instructions
Users can connect a Cat5 cable to the VDSL2 port of an
extender and require no further configuration for a powered
device (PD) to function. Users utilizing twisted pair cabling will
need to ensure to use pins 4 and 5.
Connect the Cat5 cable or twisted pair cable to the VDSL2 port
of the extender and the Powered Device (PD). The VDSL2 LED
indicator will intermittently blink at a faster rate until it remains
solidly lit indicating a successful connection.
If the LED remains blinking, the extender is attempting to
establish a handshake or link. If this is the case, the issue could
stem from a line quality issue, noise issue, or a bad connection.

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project