Extreme Networks Altitude 4532 Series Installation guide

Extreme Networks Altitude 4532 Series Installation guide
Altitude™ 4532 Series Access Point
Installation Guide
Extreme Networks, Inc.
3585 Monroe Street
Santa Clara, California 95051
(888) 257-3000
(408) 579-2800
http://www.extremenetworks.com
Published: October 2012
Part number: 120791-00 Rev 02
AccessAdapt, Alpine, Altitude, BlackDiamond, EPICenter, ExtremeWorks Essentials, Ethernet
Everywhere, Extreme Enabled, Extreme Ethernet Everywhere, Extreme Networks, Extreme Standby
Router Protocol, Extreme Turbodrive, Extreme Velocity, ExtremeWare, ExtremeWorks, ExtremeXOS, Go
Purple Extreme Solution, ExtremeXOS ScreenPlay, ReachNXT, Sentriant, ServiceWatch, Summit,
SummitStack, Triumph, Unified Access Architecture, Unified Access RF Manager, UniStack, the
Extreme Networks logo, the Alpine logo, the BlackDiamond logo, the Extreme Turbodrive logo, the
Summit logos, and the Powered by ExtremeXOS logo are trademarks or registered trademarks of
Extreme Networks, Inc. or its subsidiaries in the United States and/or other countries.
sFlow is a registered trademark of InMon Corporation.
Specifications are subject to change without notice.
All other registered trademarks, trademarks, and service marks are property of their respective
owners.
© 2012 Extreme Networks, Inc. All Rights Reserved.
Altitude™ 4532 Series Access Point Installation Guide
2
Table of Contents
Chapter 1: Introduction....................................................................................................5
Document Conventions............................................................................................................... 6
Warnings..................................................................................................................................... 6
Site Preparation .......................................................................................................................... 7
Altitude 4532 Access Point Package Contents........................................................................... 7
External Antenna Model Package Contents ........................................................................ 7
Integrated Antenna Model Package Contents ..................................................................... 7
Features...................................................................................................................................... 8
Chapter 2: Hardware Installation ....................................................................................9
Installation Instructions ............................................................................................................... 9
Precautions ............................................................................................................................... 10
Access Point Placement ........................................................................................................... 11
Integrated Antenna Model Wall Mount Instructions .................................................................. 11
Wall Mount Hardware ........................................................................................................ 11
Wall Mount Procedure ....................................................................................................... 13
Integrated Antenna Model Suspended Ceiling
T-Bar Mount Instructions........................................................................................................... 15
Suspended Ceiling Mount Procedure ................................................................................ 15
External Antenna Model Wall Mount Instructions ..................................................................... 16
Wall Mount Hardware ........................................................................................................ 16
Wall Mount Procedure ....................................................................................................... 17
External Antenna Model Suspended Ceiling Tile (Plenum) Mount Instructions........................ 18
Suspended Ceiling Mount Hardware ................................................................................. 19
Ceiling Mount Procedure ................................................................................................... 19
Antenna Options for Altitude 4532 Access Point External Antenna.......................................... 20
LED Indicators .......................................................................................................................... 21
Chapter 3: Defining A Basic Configuration..................................................................22
Using the Initial Setup Wizard................................................................................................... 22
Chapter 4: Specifications ..............................................................................................45
Altitude 4532 Access Point External Antenna Model Electrical Characteristics ....................... 45
Altitude 4532 Access Point External Antenna Model Physical Characteristics......................... 45
Altitude™ 4532 Series Access Point Installation Guide
3
Table of Contents
Altitude 4532 Access Point Integrated Antenna Model Electrical Characteristics .................... 46
Altitude 4532 Access Point Integrated Antenna Model Physical Characteristics...................... 46
Radio Characteristics................................................................................................................ 47
Chapter 5: Regulatory Information ...............................................................................48
Regulatory Information.............................................................................................................. 48
Wireless Device Country Approvals.......................................................................................... 48
Country Selection .............................................................................................................. 49
Frequency of Operation – FCC and IC .............................................................................. 49
Health and Safety Recommendations ...................................................................................... 50
Warnings for Use of Wireless Devices .............................................................................. 50
Potentially Hazardous Atmospheres – Fixed Installations................................................. 50
Safety in Hospitals............................................................................................................. 50
Pacemakers....................................................................................................................... 50
Other Medical Devices....................................................................................................... 51
RF Exposure Guidelines ........................................................................................................... 51
Safety Information ............................................................................................................. 51
International .............................................................................................................................. 51
Europe ...................................................................................................................................... 51
US and Canada ........................................................................................................................ 52
Power Supply............................................................................................................................ 52
Radio Frequency Interference Requirements – FCC................................................................ 53
Radio Frequency Interference Requirements – Canada ......................................................... 53
Radio Transmitters ............................................................................................................ 54
CE Marking and European Economic Area (EEA).................................................................... 54
Statement of Compliance.......................................................................................................... 55
Waste Electrical and Electronic Equipment (WEEE) ................................................................ 55
Japan (VCCI) - Voluntary Control Council for Interference....................................................... 57
Class B ITE ....................................................................................................................... 57
Korea Warning Statement for Class B ITE ............................................................................... 57
Other Countries ........................................................................................................................ 58
Australia............................................................................................................................. 58
Brazil.................................................................................................................................. 58
Chile .................................................................................................................................. 58
China ................................................................................................................................. 59
Mexico ............................................................................................................................... 59
South Korea....................................................................................................................... 59
Taiwan .............................................................................................................................. 60
Chapter 6: Customer Support .......................................................................................61
Registration............................................................................................................................... 61
Documentation.......................................................................................................................... 62
Altitude™ 4532 Series Access Point Installation Guide
4
1
Introduction
CHAPTER
The Altitude™ 4532 Access Point, a component of the Extreme Networks® Wireless
Mobility System, links wireless 802.11a/b/g/n devices to the Summit® WM3000 Series
Controller, enabling growth of your wireless network with a cost effective alternative to
standard Access Points. The Altitude 4532 Access Point provides two placement options:
wall and ceiling. Wall mount slots fit onto two provided screws. Arrows on the case guide
the placement of the screws. For placement above a suspended ceiling, a safety wire tie
point on the case provides for a safety wire loop. The light pipe fits through a hole in the
ceiling tile to provide a view of the unit’s status lights.
The Altitude 4532 Access Point receives all power and transfers data through the same
CAT-5 or better Ethernet cable. There is no additional power supply required. An 802.3af
Ethernet controller or Power Injector is required.
Altitude™ 4532 Series Access Point Installation Guide
5
Chapter 1: Introduction
Document Conventions
The following graphical alerts are used in this document to indicate notable situations:
NOTE
Tips, hints, or special requirements that you should take note of.
CAUTION
Care is required. Disregarding a caution can result in data loss or equipment malfunction.
WARNING!
Indicates a condition or procedure that could result in personal injury or equipment damage.
Warnings
●
Read all installation instructions and site survey reports, and verify correct equipment
installation before connecting the Altitude 4532 Access Point.
●
Remove jewelry and watches before installing this equipment.
●
Verify that the unit is grounded before connecting it to the power source.
●
Verify that any device connected to this unit is properly wired and grounded.
●
Verify there is adequate ventilation around the device, and that ambient temperatures
meet equipment operation specifications.
Altitude™ 4532 Series Access Point Installation Guide
6
Site Preparation
Site Preparation
●
Consult your site survey and network analysis reports to determine specific equipment
placement, power drops, and so on.
●
Assign installation responsibility to the appropriate personnel.
●
Identify and document where all installed components are located.
●
Ensure adequate, dust-free ventilation to all installed equipment.
●
Identify and prepare Ethernet and console port connections.
●
Verify that cable lengths are within the maximum allowable distances for optimal signal
transmission.
Altitude 4532 Access Point Package Contents
The Altitude 4532 Access Point is available in integrated antenna and external antenna
models. The contents of the package differ between the integrated antenna and external
antenna model.
External Antenna Model Package Contents
●
Altitude 4532 Access Point with external antenna connectors (Plenum Rated)
●
Two wall mount screws
●
Two wall anchors
●
Light pipe
●
Badge for light pipe
●
Altitude 4532 Access Point Installation Guide (This Guide)
Integrated Antenna Model Package Contents
●
Altitude 4532 Access Point with integrated antennas
●
Two wall mount screws
●
Two wall anchors
●
Altitude 4532 Access Point Installation Guide (This Guide)
Altitude™ 4532 Series Access Point Installation Guide
7
Chapter 1: Introduction
Features
●
One RJ-45 connector
●
LED indicators
●
Safety wire tie point
●
Slots for wall mounting
●
Clips for mounting on a suspended ceiling T-bar
●
Lock port for Kensington® style Security Lock
The Altitude 4532 Access Point has one RJ-45 connector supporting an 10/100/1000
Ethernet port and requires 802.3af-compliant power from an external source.
NOTE
When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is recommended
for Gigabit operation.
The Altitude 4532 Access Point comes with dual radios both supporting 802.11a/b/g/n.
The Access Point contains runtime firmware which enables the unit to boot after a power
up or watchdog reset. The runtime firmware on the Access Point and the firmware
downloaded from the controller can be updated via the Ethernet interface from the Wireless
Controller.
Altitude™ 4532 Series Access Point Installation Guide
8
2
Hardware Installation
CHAPTER
Installation Instructions
The Altitude 4532 Access Point mounts either on a wall (with wide-shoulder screws) or on a
suspended ceiling T-bar. This unit is not designed for mounting on a desk.
To prepare for the installation, perform the following:
1 Match the model number on the purchase order with the model numbers in the packing
list and on the case of the device shipped.
2 Verify the contents of the box include the intended Altitude 4532 Access Point and that
the included hardware matches the package contents on page 2.
SKU
Part
Number
AP4532i-US
15764
Altitude AP4532i dual-radio Independent indoor Access Point for US
regulatory domain, 802.11a/b/g/n, 2x3 MIMO, Includes internal
omnidirectional antennas, Powered by 802.3af/at PoE or by use of a
PoE injector.
AP4532i-ROW
15765
Altitude AP4532i dual-radio Independent indoor Access Point for the
Rest of the World regulatory domain, 802.11a/b/g/n, 2x3 MIMO,
Includes internal omni-directional antennas, Powered by 802.3af/at
PoE or by use of a PoE injector.
AP4532i-EU
15798
Altitude AP4532i dual-radio Independent indoor Access Point for the
European Union regulatory domain, 802.11a/b/g/n, 2x3 MIMO,
Includes internal omni-directional antennas, Powered by 802.3af/at
PoE or by use of a PoE injector.
AP4532e-US
15767
Altitude AP4532e dual-radio Independent indoor Access Point for US
regulatory domain, 802.11a/b/g/n, 2x3 MIMO. External antennas not
included-must order separately up to 6 paddle antennas. Powered by
802.3af/at PoE or by use of a PoE injector.
Description
Altitude™ 4532 Series Access Point Installation Guide
9
Precautions
SKU
Part
Number
AP4532e-ROW
15768
Altitude AP4532e dual-radio Independent indoor Access Point for the
Rest of the World regulatory domain, 802.11a/b/g/n, 2x3 MIMO.
External antennas not included-must order separately up to 6 paddle
antennas. Powered by 802.3af/at PoE or by use of a PoE injector.
AP4532e-EU
15799
Altitude AP4532e dual-radio Independent indoor Access Point for the
European Union regulatory domain, 802.11a/b/g/n, 2x3 MIMO. External
antennas not included-must order separately up to 6 paddle antennas.
Powered by 802.3af/at PoE or by use of a PoE injector.
Description
NOTE
In the above SKU numbers, "US" represents the United States regulatory model, and "ROW"
represents the Rest of World regulatory model.
3 Review site survey and network analysis reports to determine the location and mounting
position for the Altitude 4532 Access Point.
4 Connect a CAT-5 or better Ethernet cable to a compatible 802.3af power source and run
the cable to the installation site. Ensure there is sufficient slack on the cable to perform
the installation steps.
NOTE
When operating in a Gigabit Ethernet environment, CAT-5e or CAT-6 cable is recommended
for Gigabit operation.
Precautions
Before installing an Altitude 4532 Access Point, verify the following:
●
Extreme Networks recommends that you do not install the Altitude 4532 Access Point in
wet or dusty areas.
●
Verify that the environment has a continuous temperature range between 0° C to 50° C.
Altitude™ 4532 Series Access Point Installation Guide
10
Access Point Placement
Access Point Placement
For optimal performance, install the Access Point away from transformers, heavy-duty
motors, fluorescent lights, microwave ovens, refrigerators, and other industrial equipment.
Signal loss can occur when metal, concrete, walls, or floors block transmission. Install the
Access Point in an open area or add Access Points as needed to improve coverage.
Antenna coverage is analogous to lighting. Users might find an area lit from far away to be
not bright enough. An area lit sharply might minimize coverage and create dark areas.
Uniform antenna placement in an area (like even placement of a light bulb) provides even,
efficient coverage.
Place the Access Point using the following guidelines:
●
Install the Access Point at an ideal height of 10 feet from the ground.
●
Orient the Access Point antennas vertically for best reception.
To maximize the Access Point’s radio coverage area, Extreme Networks recommends
conducting a site survey to define and document radio interference obstacles before
installing the Access Point.
Integrated Antenna Model Wall Mount
Instructions
This mounting requires hanging the Altitude 4532 Access Point along its width or length
using the two slots on the bottom of the unit. The Altitude 4532 Access Point can be
mounted onto any plaster, wood, or cement wall surface using the provided wall anchors.
The following illustration displays a lengthwise mount.
Wall Mount Hardware
●
Two wide-shoulder Phillips pan head self-tapping screws
●
Two wall anchors
●
Security cable (optional)
Altitude™ 4532 Series Access Point Installation Guide
11
Integrated Antenna Model Wall Mount Instructions
NOTE
In the event that the original mounting screws are lost, the following screws can be used
instead: (ANSI Standard) #6-18 X 0.875in. Type A or AB Self-Tapping Screw, or (ANSI Standard
Metric) M3.5 X 0.6 X 20mm Type D Self-Tapping Screw.
Altitude™ 4532 Series Access Point Installation Guide
12
Integrated Antenna Model Wall Mount Instructions
Wall Mount Procedure
Integrated Antenna Wall Mount
1 Orient the case on the wall by its width or length.
Altitude™ 4532 Series Access Point Installation Guide
13
Integrated Antenna Model Wall Mount Instructions
CAUTION
To ensure proper operation of the Altitude 4532 Access Point, ensure that it is mounted
with the logo facing upwards.
2 Using the arrows on one edge of the case as guides, move the edge to the midline of the
mounting area and mark points on the midline for the screws.
3 At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall
mounting screw and stop when there is 1mm between the screw head and the wall.
NOTE
When pre-drilling a hole, the recommended hole size is 2.8mm (0.11in.) if the screws are
going directly into the wall and 6mm (0.23in.) if the provided wall anchors are being used.
4 If required, install and attach a security cable to the unit’s lock port.
5 Attach the Ethernet cable to the unit and to a controller with an 802.3af-compatible
power source.
6 Place the middle of each of the case’s mount slots over the screw heads.
7 Slide the case down along the mounting surface to hang the mount slots on the screw
heads.
8 Verify that the unit has power by observing that the LEDs are lit or flashing.
Altitude™ 4532 Series Access Point Installation Guide
14
Integrated Antenna Model Suspended Ceiling T-Bar Mount Instructions
Integrated Antenna Model Suspended Ceiling
T-Bar Mount Instructions
Ceiling mount requires holding the Altitude 4532 Access Point up against a T-bar of a
suspended ceiling grid and twisting the case onto the T-bar.
Suspended Ceiling Mount Procedure
1 If required, install and attach a security cable to the unit’s lock port.
2 Plug the Ethernet cable into the unit and to a controller with an 802.3af compatible
power source.
3 Align the bottom of the T-bar with the back of the case.
4 Orient the case by its length, and the length of the T-bar.
5 Rotate the case 45 degrees clockwise, or about 10 o’clock.
6 Push the back of the case onto the bottom of the T-bar.
7 Rotate the case 45 degrees counter-clockwise. The clips click as they fasten to the T-bar.
8 Verify the unit has power by observing the LEDs.
Altitude™ 4532 Series Access Point Installation Guide
15
External Antenna Model Wall Mount Instructions
External Antenna Model Wall Mount
Instructions
Wall mounting requires hanging the Altitude 4532 Access Point along its width or length
using the pair of slots on the bottom of the unit. The Altitude 4532 Access Point can be
mounted onto any plaster, wood, or cement wall surface using the provided wall anchors.
Wall Mount Hardware
●
Two wide-shoulder Phillips pan head self-tapping screws
●
Two wall anchors
●
Safety wire (recommended) and security cable (optional)
NOTE
In the event that the original mounting screws are lost, the following screws can be used:
(ANSI Standard) #6-18 X 0.875in. Type A or AB Self-Tapping Screw, or (ANSI Standard Metric) M3.5
X 0.6 X 20mm Type D Self-Tapping Screw.
Altitude™ 4532 Series Access Point Installation Guide
16
External Antenna Model Wall Mount Instructions
Wall Mount Procedure
1 Orient the case on the wall by its width or length.
2 Using the arrows on one edge of the case as guides, move the edge to the midline of the
mounting area and mark points on the midline for the screws.
3 At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall
mounting screw and stop when there is 1mm between the screw head and the wall.
NOTE
The recommended hole size is 2.8mm (0.11in.) if the screws are going directly into the wall,
and 6mm (0.23in.) if the provided wall anchors are being used.
4 If required, loop a safety wire, between 1.5mm (.06in.) and 2.5mm (.10in.) in diameter,
around the tie post and secure the loop.
Altitude™ 4532 Series Access Point Installation Guide
17
External Antenna Model Suspended Ceiling Tile (Plenum) Mount Instructions
5 If required, install and attach a security cable to the unit’s lock port.
6 Place the large corner of each of the case’s mount slots over the screw heads.
7 Slide the case down along the mounting surface to hang the mount slots on the screw
heads.
8 Attach appropriate antennas to the connectors.
9 Attach the Ethernet cable to the unit and to a controller with an 802.3af compatible
power source.
10 Verify the unit has power by observing that the LEDs are lit or flashing.
External Antenna Model Suspended Ceiling Tile
(Plenum) Mount Instructions
Ceiling mount requires placing the Altitude 4532 Access Point above a suspended ceiling
and installing the provided light pipe for viewing the status lights of the unit.
NOTE
Notes or warnings about suspended ceiling mounts apply to all installations where the unit is
placed on suspended ceiling tile. The case has a safety wire tie point for a standard safety wire.
CAUTION
Extreme Networks does not recommend mounting the Altitude 4532 Access Point directly to
any suspended ceiling tile with a thickness less than 12.7mm (0.5in.) or a suspended ceiling tile with
an unsupported span greater than 660mm (26in.). Extreme Networks strongly recommends fitting the
Altitude 4532 Access Point with a safety wire suitable for the specific installation. The safety wire
should be a standard ceiling suspension cable or equivalent steel wire between 1.59mm (.062in.) and
2.5mm (.10in.) in diameter.
This placement requires installation of the provided light pipe for viewing the status lights
of the unit.
Altitude™ 4532 Series Access Point Installation Guide
18
External Antenna Model Suspended Ceiling Tile (Plenum) Mount Instructions
Suspended Ceiling Mount Hardware
●
Light pipe
●
Badge for light pipe
●
Safety wire (recommended) and security cable (optional)
Ceiling Mount Procedure
Light Pipe
Ceiling Tile
Badge
1 If possible, remove the ceiling tile from its frame and place it, finished side down, on a
work surface.
2 If required, install a safety wire, between 1.5mm (.06in.) and 2.5mm (.10in.) in diameter,
in the ceiling space.
3 If required, install and attach a security cable to the unit’s lock port.
4 Mark a point on the upper or unfinished side of the tile.
5 Push the light pipe through the tile at the mark and remove the light pipe. If necessary,
use a drill to make a hole in the tile.
6 Attach appropriate antennas to the connectors.
7 Snap the clips of the light pipe into the bottom of the case.
8 Fit the light pipe into hole in the tile from its unfinished side.
9 Attach any safety wire to the safety wire tie point or security cable to the unit’s lock
port.
10 Bring the tile into the ceiling space.
Altitude™ 4532 Series Access Point Installation Guide
19
Antenna Options for Altitude 4532 Access Point External Antenna
11 Plug the Ethernet cable into the unit and to a controller with an 802.3af compatible
power source.
12 Verify the unit has power by observing the LEDs.
13 Place the ceiling tile back in its frame.
14 Snap the badge onto the light pipe from the finished side of the tile.
Antenna Options for Altitude 4532 Access Point
External Antenna
Extreme Networks supports various antennas for Altitude 4532 Access Point External
Antenna models. Select an antenna model best suited for the intended operational
environment of your Access Point.
For a more exhaustive overview of the antennas supported by the Extreme Networks
Access Point family, refer to the Enterprise Wireless LAN Antenna Specification Guide and
Enterprise Wireless LAN Antenna Specification Guide Addendum documents available from
http://www.extremenetworks.com/go/documentation.
Altitude™ 4532 Series Access Point Installation Guide
20
LED Indicators
LED Indicators
Both Integrated Antenna and External Antenna models have LED activity indicators on the
front of the case. With the External Antenna models mounted above a ceiling, LEDs are at
the center of an oval badge on the ceiling; a light pipe enables viewing the back LEDs
through the ceiling tile.
The LEDs provide a status display indicating error conditions, transmission, and network
activity for the 5 GHz 802.11a/n (amber) radio or the 2.4 GHz 802.11b/g/n (green) radio.
Task
5 GHz Activity LED (Amber)
2.4 GHz Activity LED (Green)
System Booting
Solid On (During start up only)
Solid On (During start up only)
Radio Shutdown
Administratively
or
LEDs Disabled
Off
Off
Radio Not
Configured
or
Country-code not
set
or
WLAN not mapped
to radio
Blink (On 2 seconds, Off 2 seconds)
Blink (On 2 seconds, Off 2 seconds)
Locate AP Mode
Off
Blinking
Altitude™ 4532 Series Access Point Installation Guide
21
3
Defining A Basic
Configuration
CHAPTER
An Altitude 4532 Access Point can utilize an initial setup wizard to streamline the process
of initially accessing the wireless network. The wizard defines the Access Point’s
operational mode, deployment location, basic security, network, and WLAN settings.
Using the Initial Setup Wizard
Once the Altitude 4532 Access Point is installed and powered on, complete the following
steps to get the Access Point up and running and access management functions:
1 The Access Point’s IP address is optimally provided using DHCP. A zero config IP
address can also be derived if DHCP resources are unavailable. Using zero config, the
last two octets in the IP address are the decimal equivalent of the last two bytes in the
Access Point’s hardcoded MAC address.
For example:
MAC address - 00:C0:23:00:F0:0A
Zero-config IP address - 169.254.240.10
To derive the Access Point’s IP address using its MAC address:
a Open the Windows calculator be selecting Start > All Programs > Accessories >
Calculator. This menu path may vary depending on your version of Windows.
b With the Calculator displayed, select View > Scientific. Select the Hex radio button.
c
Enter a hex byte of the Access Point’s MAC address. For example, F0.
d Select the Dec radio button. The calculator converts F0 into 240. Repeat this process
for the last Access Point MAC address octet.
Altitude™ 4532 Series Access Point Installation Guide
22
Using the Initial Setup Wizard
2 Point the Web browser to the Access Point’s IP address. The following login screen
displays:
3 Enter the default username admin in the Username field.
4 Enter the default password admin123 in the Password field.
5 Click the Login button to load the management interface.
NOTE
When logging in for the first time, you are prompted to change the password to enhance
device security in subsequent logins.
NOTE
If you get disconnected while running the wizard, you can connect again with the Access
Point’s actual IP address (once obtained) and resume the wizard.
Altitude™ 4532 Series Access Point Installation Guide
23
Using the Initial Setup Wizard
6 If this is the first time the management interface has been accessed, a dialogue displays
to start the wizard. Select Start Wizard to run the initial setup wizard.
Altitude™ 4532 Series Access Point Installation Guide
24
Using the Initial Setup Wizard
The first page of the Initial AP Setup Wizard displays the Navigation Panel and
Introduction for the configuration activities comprising the Access Point's initial setup.
A green checkmark to the left of an item in the Navigation Panel defines the listed task
as having its minimum required configuration parameters set correctly. A red X defines
the task as still requiring at least one parameter be defined correctly.
Altitude™ 4532 Series Access Point Installation Guide
25
Using the Initial Setup Wizard
The Introduction screen displays a list of the basic configuration activities supported by
the Initial Setup Wizard.
7 Select Save/Commit within each page to save the updates made to that page's
configuration. Select Next to proceed to the next page listed in the Navigation Panel.
Select Back to revert to the previous screen in the Navigation Panel without saving your
updates.
NOTE
While you can navigate to any page in the navigation panel, you cannot complete the
Initial AP Setup Wizard until each task in the Navigation Panel has a green checkmark.
Altitude™ 4532 Series Access Point Installation Guide
26
Using the Initial Setup Wizard
8 Select Next. The Initial AP Setup Wizard displays the Access Point Type screen to define
the Access Point's Standalone versus Virtual Controller AP functionality and the way the
Access Point is adopted to a controller.
Altitude™ 4532 Series Access Point Installation Guide
27
Using the Initial Setup Wizard
9 Select an Access Point Type from the following options:
●
Virtual Controller AP - When more than one Access Point is deployed, a single Access
Point can function as a Virtual Controller AP. Up to 24 Access Points can be
connected to, and managed by, a single Virtual Controller AP of the same Altitude
4532 Access Point model.
●
Standalone AP -Select this option to deploy this Access Point as an autonomous fat
Access Point. A Standalone AP isn't managed by a Virtual Controller AP, or adopted
by a RFS series controller.
NOTE
If designating the Access Point as a Standalone AP, Extreme Networks recommends the
Access Point’s UI be used exclusively to define its device configuration, and not the CLI. The CLI
provides the ability to define more than one profile and the UI does not. Consequently, the two
interfaces cannot be used collectively to manage profiles without an administrator encountering
problems.
●
Adopted to Controller - Select this option when deploying the Access Point as a
controller managed (Dependent mode) Access Point. Selecting this option closes the
Initial AP Setup Wizard. An adopted Access Point obtains its configuration from a
profile stored on its managing controller. Any manual configuration changes are
overwritten by the controller upon reboot.
Altitude™ 4532 Series Access Point Installation Guide
28
Using the Initial Setup Wizard
Select the Automatic controller discovery option to enable the Access Point to be
discovered and adopted using layer 2 settings. If preferring layer 3 adoption, select
the Static Controller Configuration option, and define the addresses of the preferred
controllers. If using the static method, you’ll also need to define whether the Access
Point receives an IP address using DHCP or if IP resources are provided statically.
Altitude™ 4532 Series Access Point Installation Guide
29
Using the Initial Setup Wizard
10 Select Next. The Initial AP Setup Wizard displays the Access Point Mode screen to define
the Access Point's routing or bridging mode functionality.
Altitude™ 4532 Series Access Point Installation Guide
30
Using the Initial Setup Wizard
11 Select an Access Point Mode from the available options.
●
Router Mode - In Router Mode, the Access Point routes traffic between the local
network (LAN) and the Internet or external network (WAN). Router mode is
recommended in a deployment supported by just a single Access Point.
●
Bridge Mode - In Bridge Mode, the AP depends on an external router for routing LAN
and WAN traffic. Routing is generally used on one device, whereas bridging is
typically used in a larger network. Thus, select Bridge Mode when deploying this
Access Point with numerous peer APs supporting clients on both the 2.4 and 5GHz
radio bands.
Altitude™ 4532 Series Access Point Installation Guide
31
Using the Initial Setup Wizard
12 Select Next. The Initial AP Setup Wizard displays the LAN Configuration screen to set the
Access Point's LAN interface configuration.
Altitude™ 4532 Series Access Point Installation Guide
32
Using the Initial Setup Wizard
13 Set the following DHCP and Static IP Address/Subnet information for the LAN
interface:
●
Use DHCP - Select the checkbox to enable an automatic network address
configuration using the Access Point’s DHCP server.
●
Static IP Address/Subnet - Enter an IP Address and a subnet for the Access Point's
LAN interface. If Use DHCP is selected, this field is not available. When selecting this
option, define the following DHCP Server and Domain Name Server (DNS) resources,
as those fields will become enabled on the bottom portion of the screen.
●
-
Use on-board DHCP server to assign IP addresses to wireless clients - Select the
checkbox to enable the Access Point’s DHCP server to provide IP and DNS
information to clients on the LAN interface.
-
Range - Enter a starting and ending IP Address range for client assignments on the
Access Point's LAN interface. Avoid assigning IP addresses from x.x.x.1 - x.x.x.10
and x.x.x.255, as they are often reserved for standard network services. This is a
required parameter.
-
Default Gateway - Define a default gateway address for use with the default
gateway. This is a required parameter.
DNS Forwarding - Select this option to allow a DNS server to translate domain names
into IP addresses. If this option is not selected, a primary and secondary DNS
resource must be specified. DNS forwarding is useful when a request for a domain
name is made but the DNS server, responsible for converting the name into its
corresponding IP address, cannot locate the matching IP address.
-
Primary DNS - Enter an IP Address for the main Domain Name Server providing
DNS services for the Access Point's LAN interface.
-
Secondary DNS - Enter an IP Address for the backup Domain Name Server
providing DNS services for the Access Point's LAN interface
Altitude™ 4532 Series Access Point Installation Guide
33
Using the Initial Setup Wizard
14 Select Next. The Initial AP Setup Wizard displays the WAN Configuration screen to set the
Access Point's WAN interface configuration.
Altitude™ 4532 Series Access Point Installation Guide
34
Using the Initial Setup Wizard
15 Set the following DHCP and Static IP Address/Subnet information for the WAN
interface:
●
Use DHCP - Select the checkbox to enable an automatic network address
configuration using the Access Point’s DHCP server.
●
Static IP Address/Subnet - Enter an IP Address/Subnet and gateway for the Access
Point's WAN interface. These are required fields
●
The port connected to the WAN - Select the port used as the physical Access Point
connection to the external network. The ports available differ depending on the
Access Point model deployed. Access point models with a single port have this
option fixed.
●
Enable NAT on the WAN Interface - Select the checkbox to allow traffic to pass between
the Access Point's WAN and LAN interfaces.
16 Select Next. The Initial AP Setup Wizard displays the Radio Configuration screen to define
support for the 2.4GHz radio band, 5GHz radio band or to set the radio's functionality
as a dedicated sensor. An Altitude 4532 Access Point supports a single dual-band radio.
Altitude™ 4532 Series Access Point Installation Guide
35
Using the Initial Setup Wizard
NOTE
The ADSP Sensor Support field displays at the bottom of the screen only if a radio has
been dedicated as a sensor.
17 Set the following parameters for the radio:
●
Configure as a Data Radio - Select this option to dedicate this radio for WLAN client
support in either the selected 2.4 or 5GHz radio band.
-
Radio Frequency Band - Select either the 2.4GHz or 5.0GHz radio band to use with
the radio when selected as a Data Radio. The selected band is used for WLAN
client support. Considers selecting one radio for 2.4GHz and another for 5GHz
support (if using a dual or three radio model) when supporting clients in both the
802.11bg and 802.11n bands.
-
Power Level - Use the spinner control to select a 1 - 23 dBm minimum power level
to assign to this radio in selected 2.4 or 5.0 GHz band. 1 dBm is the default
setting.
-
Channel Mode - Select either Random, Best or Static. Select Random for use with a
802.11a/n radio. To comply with Dynamic Frequency Selection (DFS) requirements
in the European Union, the 802.11a/n radio uses a randomly selected channel
each time the Access Point is powered on.
Select Best to enable the Access Point to scan non-overlapping channels and listen
for beacons from other Access Points. After the channels are scanned, it will select
the channel with the fewest Access Points. In the case of multiple Access Points on
the same channel, it will select the channel with the lowest average power level.
When Constantly Monitor is selected, the Access Point will continuously scan the
network for excessive noise and sources of interference. Select Static to assign the
Access Point a permanent channel and scan for noise and interference only when
initialized.
●
Configure as a Sensor Radio - Select this option to dedicate the radio to sensor support
exclusively. When functioning as a sensor, the radio scans in sensor mode across all
channels within the 2.4 and 5.0GHz bands to identify potential threats within the
Access Point managed network. If dedicating a radio as a sensor resource, a primary
and secondary ADSP server must be specified as an ADSP management resource.
●
Disable the Radio - Select this option to disable this radio, thus prohibiting it from
either providing WLAN or sensor support. Verify this course action with your
network administrator before rendering the radio offline.
Altitude™ 4532 Series Access Point Installation Guide
36
Using the Initial Setup Wizard
NOTE
If configuring an Altitude 4532 Access Point as a sensor, the Access Point will require a
reboot before its sensor functionality is invoked. The reboot can take place at the completion of the
Initial AP Setup Wizard.
Altitude™ 4532 Series Access Point Installation Guide
37
Using the Initial Setup Wizard
18 Select Next. The Initial AP Setup Wizard displays the Wireless LAN Setting screen to
define network address and security settings for two WLAN configurations available to
the Access Point as part of the Initial AP Setup Wizard. Once the Access Point has an
initial configuration defined, numerous additional WLAN configurations can be set.
Altitude™ 4532 Series Access Point Installation Guide
38
Using the Initial Setup Wizard
19 Set the following parameters for each of the two WLAN configurations available as part
of this Initial AP Setup Wizard:
●
SSID - Enter or modify the Services Set Identification (SSID) associated with the
WLAN. The WLAN name is auto-generated using the SSID until changed by the
user. The maximum number of characters is 32. Do not use < > | “ & \ ? , This is a
required parameter for each WLAN.
●
WLAN Type - Set the data protection scheme used by clients and Access Points within
the WLAN. The following options are available:
-
No Authentication and no Encryption - Select this option to provide no security
between the Access Point and connected clients on this WLAN.
-
Captive Portal Authentication and No Encryption - Select this option to use a Web
page (either internally or externally hosted) to authenticate users before access is
granted to the network. If using this option, define whether a local or external
RADIUS authentication resource is used.
-
PSK Authentication and WPA2 Encryption - Select the option to implement a preshared key that must be correctly shared between the Access Point and requesting
clients using this WLAN. If using this option, specify a WPA key in either ASCII
(8-63 characters) or HEX (64 characters) format.
-
EAP Authentication and WPA2 Encryption - Select this option to authenticate clients
within this WLAN through the exchange and verification of certificates. If using
this option, define whether a local or external RADIUS authentication resource is
used.
●
WPA Key - If a WPA key is required (PSK Authentication and WPA2 Encryption),
enter an alphanumeric string of 8 to 63 ASCII characters or 64 HEX characters as the
primary string both transmitting and receiving authenticators must share. The
alphanumeric string allows character spaces. This passphrase saves the administrator
from entering the 256-bit key each time keys are generated.
●
RADIUS Server - If the WLAN type requires a RADIUS server to validate user
credentials, designate whether the Access Point is using an External RADIUS Server
resource or the Access Point's own Onboard RADIUS Server. If using an external
RADIUS server resource, provide the IP address of the external server and the shared
secret used to authenticate the request.
Altitude™ 4532 Series Access Point Installation Guide
39
Using the Initial Setup Wizard
NOTE
If using the Access Point’s onboard RADIUS server, an additional RADIUS Server
Configuration screen displays within the Navigation Panel on the left-hand side of the screen. Use
this screen to create user accounts validated when the Access Point authenticates client
connection requests to the onboard RADIUS server.
20 Select Next. The Initial AP Setup Wizard displays the RADIUS Server Configuration screen
if the Access Point’s onboard RADIUS server is required to validate user requests. If an
onboard RADIUS server is not required, the Initial AP Setup Wizard displays the
Country/Date/Time screen to set device deployment, administrative contact and system
time information.
Altitude™ 4532 Series Access Point Installation Guide
40
Using the Initial Setup Wizard
21 Refer to the Username, Password, Description and Actions columns to review credentials of
existing RADIUS Server user accounts. Add new accounts or edit the properties of
existing accounts as updates are required.
22 Refer to the Add On-Board RADIUS Server Users field to set the following parameters for
a user account:
●
Username - If adding a new user account, create a username up to X characters in
length. The username cannot be revised if modifying the user configuration. This is a
required parameter.
●
Password - Provide (or modify) a password between X - X characters in length entered
each time a requesting client attempts access to the AP managed network using the
Access Point's onboard RADIUS server. This is a required parameter.
●
Confirm Password - Re-enter (or modify) the password as a means of confirming the
password. This is a required parameter.
●
Description - Optionally provide a description of the user account as a means of
further differentiating it from others.
23 When completed, select Add User to commit a new user, Modify User to commit a
modified user or Reset to clear the screen without updating the configuration. Selecting
Reset clears the field of all entered user account information.
Altitude™ 4532 Series Access Point Installation Guide
41
Using the Initial Setup Wizard
24 Select Next. The Initial AP Setup Wizard displays the Country/Date/Time screen to set
device deployment, administrative contact and system time information. The system
time can either be set manually or be supplied by a dedicated Network Time Protocol
(NTP) resource.
Altitude™ 4532 Series Access Point Installation Guide
42
Using the Initial Setup Wizard
25 Refer to the Country and Time Zone field to set the following device deployment
information:
●
Location - Define the location of the Access Point. The Location parameter acts as a
reminder of where the AP can be located within the Extreme Networks managed
wireless network.
●
Contact - Specify the contact information for the administrator. The credentials
provided should accurately reflect the individual responding to service queries.
●
Country - Select the Country where the Access Point is deployed. The Access Point
prompts for the correct country code on the first login. A warning message also
displays stating an incorrect country setting may result in illegal radio operation.
Selecting the correct country is central to legal operation. Each country has its own
regulatory restrictions concerning electromagnetic emissions and the maximum RF
signal strength that can be transmitted. This is a required parameter.
●
Time Zone - Set the time zone where the Access Point is deployed. This is a required
parameter. The setting should be complimentary with the selected deployment
country.
26 If an NTP resource is unavailable, set the System Date and Time (calendar date, time and
AM/PM designation).
27 Optionally enter the IP address of a server used to provide system time to the Access
Point. Once the IP address is entered, the Network Time Protocol (NTP) functionality is
engaged automatically for synchronization with the NTP resource.
28 If an NTP resource is unavailable, set the System Date and Time (calendar date, time and
AM/PM designation).
29 Optionally enter the IP address of a server used to provide system time to the Access
Point. Once the IP address is entered, the Network Time Protocol (NTP) functionality is
engaged automatically for synchronization with the NTP resource.
30 Select Next. The Initial AP Setup Wizard displays the Summary and Commit screen to
summarize the screens (pages) and settings updated using the Initial AP Setup Wizard.
Altitude™ 4532 Series Access Point Installation Guide
43
Using the Initial Setup Wizard
There's no user intervention or additional settings required within this screen. Its an
additional means of validating the configuration before its deployed. However, if a
screen displays settings not intended as part of the initial configuration, the screen can
be selected from within the Navigation Panel and its settings modified accordingly.
31 If the configuration displays as intended, select the Save/Commit button to implement
these settings to the Access Point’s configuration. If additional changes are warranted
based on the summary, either select the target page from the Navigational Panel, or use
the Back and Next buttons to scroll to the target screen.
Altitude™ 4532 Series Access Point Installation Guide
44
4
Specifications
CHAPTER
Altitude 4532 Access Point External Antenna
Model Electrical Characteristics
An Altitude 4532 Access Point External Antenna model Access Point has the following
electrical characteristics:
Operating Current & Voltage
180ma- 270ma @ 48VDC using Power over Ethernet
Altitude 4532 Access Point External Antenna
Model Physical Characteristics
An Altitude 4532 Access Point External Antenna model Access Point has the following
physical characteristics:
Dimensions
8.50 in. Depth x 5.5 in. Width x 1.5 in. Height
21.59 cm Depth x 13.97 cm Width x 3.81 cm Height
Housing
Metal
Weight
2.5 lbs / 1.13 kg
Operating Temperature
32°F to 122°F/0°C to 50°C
Storage Temperature
-40°F to 158°F/-40°C to 70°C
Operating Humidity
5 to 95% Relative Humidity non-condensing
Storage Humidity
85% Relative Humidity non-condensing
Operating Altitude (max)
8,000 ft @ 28C
Storage Altitude (max)
30,000 ft @ 12C
Electrostatic Discharge
+/-15kV Air and +/-8kV Contact @ 50% Relative Humidity
Altitude™ 4532 Series Access Point Installation Guide
45
Altitude 4532 Access Point Integrated Antenna Model Electrical Characteristics
Altitude 4532 Access Point Integrated Antenna
Model Electrical Characteristics
An Altitude 4532 Access Point Integrated model Access Point has the following electrical
characteristics:
Operating Current
& Voltage
180ma- 270ma @ 48VDC using Power over Ethernet
Altitude 4532 Access Point Integrated Antenna
Model Physical Characteristics
An Altitude 4532 Access Point Integrated Antenna model Access Point has the following
physical characteristics:
Dimensions
9.50 in. Depth x 7.5 in. Width x 1.9 in. Height
24.13 cm Depth x 19.05 cm Width x 4.83 cm Height
Housing
Plastic
Weight
2.0 lbs / 0.91 kg
Operating Temperature
32°F to 122°F/0°C to 50°C
Storage Temperature
-40°F to 158°F/-40°C to 70°C
Operating Humidity
5 to 95% Relative Humidity non-condensing
Storage Humidity
85% Relative Humidity non-condensing
Operating Altitude (max)
8,000 ft @ 28C
Storage Altitude (max)
30,000 ft @ 12C
Electrostatic Discharge
+/-15kV Air and +/-8kV Contact @ 50% Relative Humidity
Altitude™ 4532 Series Access Point Installation Guide
46
Radio Characteristics
Radio Characteristics
The Altitude 4532 Access Point model Access Points have the following radio
characteristics:
Operating
Channels
All channels from 4920 MHz to 5825 MHz except channel
52 -64
Channels 1-13 (2412-2472 MHz)
Channel 14 (2484 MHz) Japan only
Actual operating frequencies depend on regulatory
approval for the country of use.
Data Rates
Supported
802.11b: 1,2,5.5,11Mbps
802.11g: 1,2,5.5,11,6,9,12,18,24,36,48, and 54Mbps
802.11a: 6,9,12,18,24,36,48, and 54Mbps
802.11n: MCS 0-15 up to 300Mbps
Wireless Medium
Direct Sequence Spread Spectrum (DSSS),
Orthogonal Frequency Division Multiplexing (OFDM)
Spatial multiplexing (MIMO)
Network Standards
802.11a, 802.11b, 802.11g, 802.3, 802.11n (Draft 2.0)
Maximum Available Maximum available conducted transmit power per chain:
Transmit Power
2.4 GHz: 21dBm
Maximum available conducted transmit power all chains:
2.4 GHz: 24dBm
Maximum available conducted transmit power per chain:
5 GHz: 19dBm
Maximum available conducted transmit power all chains:
5 GHz: 22dBm
Transmit Power
Adjustment
1dB increments
Antenna
Configuration
2x3 MIMO (transmit on two and receive on all three
antennas)
Altitude™ 4532 Series Access Point Installation Guide
47
5
Regulatory Information
CHAPTER
Regulatory Information
This device is approved under the Symbol Technologies, Inc. brand: Symbol Technologies,
Inc. is a wholly owned subsidiary of Motorola Solutions, Inc. (collectively "Motorola").
This guide applies to Model Number AP-0650
All Extreme Networks devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Any changes or modifications to Extreme Networks equipment, not expressly approved by
Extreme Networks, could void the user’s authority to operate the equipment.
Extreme Networks devices are professionally installed, the Radio Frequency Output Power
will not exceed the maximum allowable limit for the country of operation.
Antennas: Use only the supplied or an approved replacement antenna. Unauthorized
antennas, modifications, or attachments could cause damage and may violate regulations.
This device is only to be used with an Extreme Networks Wireless Controller.
Wireless Device Country Approvals
Regulatory markings, subject to certification, are applied to the device signifying the
radio(s) is/are approved for use in the following countries: United States, Canada, Japan,
China, S. Korea, Australia, and Europe.
Altitude™ 4532 Series Access Point Installation Guide
48
Wireless Device Country Approvals
Please refer to the Declaration of Conformity (DoC) for details of other country markings. This
is available at http://www.extremenetworks.com/go/rfcertification.htm.
Note: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech
Republic, Cyprus, Denmark, Estonia, FinlFor 2.4GHz or 5GHz Products: Europe includes,
Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic,
Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Operation of the device without regulatory approval is illegal.
Country Selection
Select only the country in which you are using the device. Any other selection will make the
operation of this device illegal.
Frequency of Operation – FCC and IC
5 GHz Only
The use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250
MHz) is restricted to Indoor Use Only; any other use will make the operation of this device
illegal.
Industry Canada Statement:
Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce
potential for harmful interference to co-Channel mobile satellite systems. High power
radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and
5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN
devices.
Avertissement: Le dispositive fonctionnant dans la bande 5150-5250 MHz est réservé
uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
Altitude™ 4532 Series Access Point Installation Guide
49
Health and Safety Recommendations
Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.,
qu'ils ont la priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars
pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Health and Safety Recommendations
Warnings for Use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless devices.
Potentially Hazardous Atmospheres – Fixed Installations
You are reminded of the need to observe restrictions on the use of radio devices in fuel
depots, chemical plants etc. and areas where the air contains chemicals or particles (such as
grain, dust, or metal powders).
Safety in Hospitals
Wireless devices transmit radio frequency energy and may affect medical electrical
equipment. When installed adjacent to other equipment, it is advised to verify that
the adjacent equipment is not adversely affected.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained
between a handheld wireless device and a pacemaker to avoid potential interference with
the pacemaker. These recommendations are consistent with independent research and
recommendations by Wireless Technology Research.
Persons with Pacemakers:
●
Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when
turned ON.
●
Should not carry the device in a breast pocket.
Altitude™ 4532 Series Access Point Installation Guide
50
RF Exposure Guidelines
●
Should use the ear furthest from the pacemaker to minimize the potential for
interference.
●
If you have any reason to suspect that interference is taking place, turn OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if the
operation of your wireless product may interfere with the medical device.
RF Exposure Guidelines
Safety Information
Reducing RF Exposure—Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human exposure to
electromagnetic fields from radio devices. For information on “International” human
exposure to eletromagnic fields refer to the Extreme Networks Declaration of Conformity
(DoC) at http://www.extremenetworks.com/go/rfcertification.htm.
Europe
Remote and Standalone Antenna Configurations
To comply with EU RF exposure requirements, antennas that are mounted externally at
remote locations or operating near users at stand-alone desktop of similar configurations
must operate with a minimum separation distance of 20 cm from all persons.
Altitude™ 4532 Series Access Point Installation Guide
51
US and Canada
US and Canada
Co-located statement
To comply with FCC RF exposure compliance requirement, the antenna used for this
transmitter must not be co-located or operating in conjunction with any other transmitter/
antenna except those already approved in this filling.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth foa na uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator and your body.
NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Remote and Standalone Antenna Configurations
To comply with FCC RF exposure requirements, antennas that are mounted externally at
remote locations or operating near users at stand-alone desktop of similar configurations
must operate with a minimum separation distance of 20 cm from all persons.
To satisfy FCC RF exposure requirements, a mobile transmitting device must operate with a
minimum separation distance of 20 cm or more from a person’s body.
Power Supply
This device can be powered from a 802.3af compliant power source which is certified by the
appropriate agencies.
Altitude™ 4532 Series Access Point Installation Guide
52
Radio Frequency Interference Requirements – FCC
Radio Frequency Interference Requirements –
FCC
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
●
Reorient or relocate the receiving antenna
●
Increase the separation between the equipment and receiver
●
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
●
Consult the dealer or an experienced radio/TV technician for help
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
For RLAN Devices:
The use of 5 GHz RLAN’s, for use in the US, have the following restrictions:
●
Notched Band 5.60 – 5.65 GHz
Radio Frequency Interference Requirements –
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Altitude™ 4532 Series Access Point Installation Guide
53
CE Marking and European Economic Area (EEA)
Radio Transmitters
For RLAN Devices:
The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:
●
Restricted Band 5.60 – 5.65 GHz
This device complies with RSS 210 of Industry Canada. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils
radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter
tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
Label Marking: The Term "IC:" before the radio certification only signifies that Industry
Canada technical specifications were met.
To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that
permitted for successful communication.
This device has been designed to operate with the antennas listed in section 13 of Enterprise
Wireless LAN Antenna Specification Guide (72E-133063-01). Antennas not included in this
list or having a greater gain are strictly prohibited for use with this device. The required
antenna impedance is 50 ohms.
CE Marking and European Economic Area
(EEA)
The use of 2.4 GHz RLAN’s, for use through the EEA, have the following
restrictions:
●
Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835
GHz.
●
France, outside usage is restricted to 2.4 – 2.454 GHz.
●
Italy requires a user license for outside usage.
Altitude™ 4532 Series Access Point Installation Guide
54
Statement of Compliance
Statement of Compliance
Extreme Networks hereby, declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of
Conformity may be obtained from http://www.extremenetworks.com/go/rfcertification.htm.
Waste Electrical and Electronic Equipment
(WEEE)
English: For EU Customers: All products at the end of their life must be returned to Extreme Networks
for recycling. For information on how to return product, please go to:
http://www.extremenetworks.com/go/eu-weee.
Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés
à Extreme Networks pour recyclage. Pour de plus amples informations sur le retour de produits,
consultez : http://www.extremenetworks.com/go/eu-weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Extreme
Networks al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo
devolver un producto, visite: http://www.extremenetworks.com/go/eu-weee.
Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщат на
Extreme Networks за рециклиране. За информация относно връщането на продукти, моля отидете на адрес:
http://www.extremenetworks.com/go/eu-weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum
Recycling an Extreme Networks zurückgesandt werden. Informationen zur Rücksendung von Produkten
finden Sie unter http://www.extremenetworks.com/go/eu-weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono
essere restituiti a Extreme Networks al fine di consentirne il riciclaggio. Per informazioni sulle modalità di
restituzione, visitare il seguente sito Web: http://www.extremenetworks.com/go/eu-weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Extreme
Networks para reciclagem. Para obter informações sobre como devolver o produto, visite:
http://www.extremenetworks.com/go/eu-weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar
Extreme Networks te worden teruggezonden voor recycling. Raadpleeg
http://www.extremenetworks.com/go/eu-weee voor meer informatie over het terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy
Extreme Networks w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie
internetowej http://www.extremenetworks.com/go/eu-weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti
Extreme Networks k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce:
http://www.extremenetworks.com/go/eu-weee.
Altitude™ 4532 Series Access Point Installation Guide
55
Waste Electrical and Electronic Equipment (WEEE)
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil
Extreme Networks'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi:
http://www.extremenetworks.com/go/eu-weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Extreme Networks vállalathoz kell
eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért
látogasson el a http://www.extremenetworks.com/go/eu-weee weboldalra.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Extreme
Networks för återvinning. Information om hur du returnerar produkten finns på
http://www.extremenetworks.com/go/eu-weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Extreme
Networks-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa
http://www.extremenetworks.com/go/eu-weee.
Dansk: Til kunder i EU: Alle produkter skal returneres til Extreme Networks til recirkulering, når de er
udtjent. Læs oplysningerne om returnering af produkter på:
http://www.extremenetworks.com/go/eu-weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να
επιστρέφονται στην Extreme Networks για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την
επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση http://www.extremenetworks.com/go/eu-weee
στο ∆ιαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu
rritornati għand Extreme Networks għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott,
jekk jogħġbok żur: http://www.extremenetworks.com/go/eu-weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie
returnate la Extreme Networks pentru reciclare. Pentru informaţii despre returnarea produsului, accesaţi:
http://www.extremenetworks.com/go/eu-weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Extreme
Networks za reciklažo. Za informacije o vračilu izdelka obiščite:
http://www.extremenetworks.com/go/eu-weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti
vrátené spoločnosti Extreme Networks na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na:
http://www.extremenetworks.com/go/eu-weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į
kompaniją „Extreme Networks“. Daugiau informacijos, kaip grąžinti gaminį, rasite:
http://www.extremenetworks.com/go/eu-weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Extreme
Networks otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Extreme Networks,
lūdzu, skatiet: http://www.extremenetworks.com/go/eu-weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Extreme Networks'ya
iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin:
http://www.extremenetworks.com/go/eu-weee.
Turkish WEEE Statement of Compliance
EEE Yönetmeliğine Uygundur
Altitude™ 4532 Series Access Point Installation Guide
56
Japan (VCCI) - Voluntary Control Council for Interference
Japan (VCCI) - Voluntary Control Council for
Interference
Class B ITE
この装置は、情報処理装置等電波障害自主規制協議会 (VCCI)の基準に基づくク
ラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としています
が、この装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引
き起こすことがあります。取扱説明書に従って正しい取り扱いをして下さい。
This is a Class B product based on the standard of the Voluntary Control Council for
Interference from Information Technology Equipment (VCCI). If this is used near a radio or
television receiver in a domestic environment, it may cause radio interference. Install and
use the equipment according to the instruction manual.
Korea Warning Statement for Class B ITE
기종별
B 급 기기
( 가정용 방송통신기기 )
사용자안내문
이 기기는 가정용 (B 급 ) 으로 전자파적합등록을
한 기기로서 주로 가정에서 사용하는 것을 목적
으로 하며 , 모든 지역에서 사용할 수 있습니다 .
Class B
(Broadcasting Communication Device
for Home Use)
This device obtained EMC registration mainly for
home use (Class B) and may be used in all areas.
Altitude™ 4532 Series Access Point Installation Guide
57
Other Countries
Other Countries
Australia
Use of 5 GHz RLAN’s in Australia is restricted in the following band 5.50 – 5.65 GHz.
Brazil
Regulatory declarations for Altitude 4532- BRAZIL
Note: The certification mark applied to the Altitude 4532 is for Restrict Radiation
Equipment. This equipment operates on a secondary basis and does not have the right for
protection against harmful interference from other users including same equipment types.
Also this equipment must not cause interference to systems operating on primary basis.
For more information consult the website http://www.anatel.gov.br
Declarações Regulamentares para AP-650 - Brasil
Nota: "A marca de certificação se aplica ao Transceptor, modelo Altitude 4532. Este
equipamento opera em caráter secundário, isto é, não tem direito a proteção contra
interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência
a sistemas operando em caráter primário.”
Para maiores informações sobre ANATEL consulte o site: http://www.anatel.gov.br
Chile
“Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de
telecomunicaciones, relativa a radiaciones electromagnéticas.”.
"This device complies with the Resolution Not 403 of 2008, of the Undersecretary of
telecommunications, relating to electromagnetic radiation.”
Altitude™ 4532 Series Access Point Installation Guide
58
Other Countries
China
Quality Certificate in Chinese when the factory has ISO 9001 certification.
Mexico
Restrict Frequency Range to: 2.450 – 2.4835 GHz.
South Korea
For a radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following two
expression should be displayed:”
당해 무선설비는 운용 중 전파혼신 가능성이 있음
당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다
Altitude™ 4532 Series Access Point Installation Guide
59
Other Countries
Taiwan
臺灣
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象
時,應立即停用,且改善至無干擾時方得繼續使用。
前項合法通信,指依電信規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干
擾。
在 5.25-5.35 赫頻帶內操作之無線資訊傳輸設備,限於室內使用。
Altitude™ 4532 Series Access Point Installation Guide
60
6
Customer Support
CHAPTER
NOTE
Services can be purchased from Extreme Networks or through one of its channel partners. If
you are an end-user who has purchased service through an Extreme Networks channel partner,
please contact your partner first for support.
Extreme Networks Technical Assistance Centers (TAC) provide 24x7x365 worldwide
coverage. These centers are the focal point of contact for post-sales technical and networkrelated questions or issues. TAC will create a Service Request (SR) number and manage all
aspects of the SR until it is resolved. For a complete guide to customer support, see the
Technical Assistance Center User Guide at:
http://www.extremenetworks.com/go/TACUserGuide
The Extreme Networks eSupport website provides the latest information on Extreme
Networks products, including the latest Release Notes, troubleshooting, downloadable
updates or patches as appropriate, and other useful information and resources. Directions
for contacting the Extreme Networks Technical Assistance Centers are also available from
the eSupport website at:
https://esupport.extremenetworks.com
Registration
If you have not already registered with Extreme Networks using a registration card
supplied with your product, you can register on the Extreme Networks website at:
http://www.extremenetworks.com/go/productregistration
Altitude™ 4532 Series Access Point Installation Guide
61
Chapter 6: Customer Support
Documentation
Check for the latest versions of documentation on the Extreme Networks documentation
website at:
http://www.extremenetworks.com/go/documentation
Altitude™ 4532 Series Access Point Installation Guide
62
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement