USER MANUAL

COOKER HOOD

PRIME

CONTENT

1.Notice

------------------------------------------------------------------------------------------------ P1

2.Feature

----------------------------------------------------------------------------------------------- P1

3.Installation

---------------------------------------------------------------------------------------- P1-4

4.Cleaning & maintenance

------------------------------------------------------------- P4-8

5.Use

------------------------------------------------------------------------------------------------------- P8

6.Safety Warning

-------------------------------------------------------------------------------- P8-9

7.Abnormity and Solution

---------------------------------------------------------------- P9

8.Environmental Note

------------------------------------------------------------------------- P10

1.NOTICE

1. Thank you for choosing our cooker hood. Please read the instruction manual carefully before use.

2. The installation must be undertaken by a qualified and competent contractor.

3. The manufacturer disclaims all liability for any damage or injury caused as a result of not following instructions for installation contained in the following text.

4. When installing the cooker hood, ensure that the following recommended distances are being observed between the cooker top and the bottom of the cooker hood:

 Electric cookers：600mm

 Gas cookers：650mm

 Coal/oil cookers：800mm

The cooker hood is used on 220~240v, 50/60Hz.

2.FEATURE

1. The cooker hood uses high quality materials, and is made with a fashion design.

2. Equipped with a low noise electric motor and centrifugal fan, it produces strong suction, low noise, non-stick grease filter and easy to clean.

3. With the isolated low voltage circuit board control, 12VDC input, the lights are therefore safer.

4. Special wind tunnel construction, and free dirt will be absorbed in a second.

3.INSTALLATION

IMPORTANT: Before installation and usage, read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The rating plate can be found behind the grease filters.

The manufacturer declines all responsibility in the event of the installer failing to observe all the accident prevention regulations in force, which are necessary for normal use and the regular operation of the electric system.

3.1. ELECTRICAL CONNECTION

YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT

INSTALLATION.

 The power cable must be connected to the terminals marked L (live) and N (neutral) in the hood and fixed with a cable clamp.

 The cooker hood’s power cable must be fitted upstream from the electrical connection, using an omni-polar switch with a contact distance of at least 3mm.

3.2.G INSTALLATION

 Check that the product purchased is of suitable size for the chosen installation area.

 Carry out all necessary masonry work prior to the fitting of the cooker hood.

 Ensure that all electrical connections are carried out by a suitably qualified person.

 Before commencing installation of the cooker hood the grease filter should be removed.

 Check inside the product and ensure that there is no transit packaging or any other materials, such as packets of screws, guarantee etc. These should be removed and kept for future use.

 If possible, disconnect and move freestanding or slot-in cookers from their position, to provide easier access to the rear wall and ceiling. If this is not possible, then a thick, protective covering should be placed over the worktop, hob top or cooker. This will help to protect these surfaces from damage and debris.

 Select a flat surface for assembling the cooker hood. Cover that surface with a protective covering and place all cooker hood parts and fittings on it.

 In addition check whether there is an electrical socket available, which will be accessible after the hood is mounted. If you are going to use the appliance in extractor mode, you should also ensure that there is space to connect a fumes discharge device to the outside.

 Raw plugs are provided to secure the hood to most types of walls and ceilings. However a qualified technician must verify the suitability of the materials, in accordance with the type of wall and ceiling. The wall and ceiling must strong enough to take the weight of the hood.

Do not tile, grout or silicone this appliance to the wall. This appliance is designed to be surface mounted only.

3.3. INSTALLING YOUR COOKER HOOD

IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE INSTALLATION YOUR

COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR

RECIRCULATION MODE. PLEASE TURN TO PAGE 8 NOW TO UNDERSTAND

THE DIFFERENCES BETWEEN THERES TWO MODES.

 The cooker hood should not be exposed to a direct heat source from the cooking device underneath it, i.e. naked flame from a gas burner or heat from electric hob zones without a pan on them.

 We recommend that at least two people install this hood.

 The lights on this appliance should only be used during operation of the cooker hood. They should not be left on permanently and used as a lighting source.

IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO YOUR MAINS

SUPPLY AFTER THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED.

-------Installation for Side suction:

1) Remove the metal grease filters (as shown above).

2) Position the hood against the wall that you are intending to install it and mark the position of the support holes that are to be drilled.

3) Using a drill bit with an 8 mm diameter, make holes in the wall on the positions that you have marked in step 2, and insert raw plug

②

into the holes that you have drilled(as shown on the right).

4) Screw the hook into the wall at Hole B.

5) Put the range hood on the wall which will install the product, then mark the position of safety screw and fixing screw, in order to facilitate drilling (picture ⑤). The two gourd shaped holes upper the product are for fixing screw. The two circular holes lower the product are for safety screw.

④

⑤

⑥ ⑦

6) Connect the check valve onto the top of the chimney section. And then connect the ducting hose to the check valve.

 The other end of the ducting hose should be connected to your discharge outlet that is suitable for cooking vapors. It should have a cross section of at least 150 ㎡.

 The maximum distance between the check valve and your discharge outlet should be 3 meters, with one 90 degree bend.

7) Install the Chimney Section C and Fixing Bracket E

 Connect the Chimney Section C and Fixing Bracket E. Put the bottom part of this coupling on the cooker hood. Mark the fixing holes between the bracket and wall with a pencil. And remove the

Chimney Section and Fixing Bracket E.

 Using a drill bit with an 8 mm diameter make holes in the wall on the positions that you have marked, and insert raw plugs. Screw the chimney section and bracket fixing into the wall tightly.

4. CLEANING AND MAINTENANCE

IMPORTANT: BEFORE CLEANING, MAKE SURE THE POWER IS CUT OFF,

AND UNPLUG THE PLUG FROM THE OUTLET.

4.1.CLEANING

 Clean the external parts of your cooker hood with mild liquid detergent and new damp cloth.

 Never use abrasive powder, corrosive solvents or brushes.

 Never insert pointed objects into the cooker hood’s protective grid.

 Only clean control panel and grease filter with mild liquid detergents and a new damp cloth.

 If you are using the appliance in recirculation mode, then be sure to replace the carbon filter at the recommended interval (see section on “Fitting the carbon filter”). A build up of grease could cause a fire hazard.

 Never attempt to clean the area above the grease filters.

 Your cooker hood includes a grease filter which helps to absorb grease particles to protect your kitchen & furniture from greasy residues.

 To prevent this fire hazard, the filter should be cleaned regularly.

 Depending on use, this should be done every 10-15 days or at least once a month, using hot water and normal washing-up detergent.

 DO NOT WASH THE GREASE FILTER IN A DISHWASHER.

4.2.MAINTENANCE

 First remove the grease filter by pulling down on it.

 Undo the side catches.

 Soak the grease filter in hot water and washing up liquid for about an hour.

 Rinse them off thoroughly with hot water.

 Repeat the process or change the grease filter if required.

 Refit the grease filters once they have dried.

IMPORTANT: LET THE GREASE FILTERS DRY THOROUGHLY BEFORE REFITTING

THEM IN THE COOKER HOOD.

4.3.CHANGING A LIGHT BULB

IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB,

YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER

HOOD FROM YOUR MAINS SUPPLY.



Remove the grease filters；



Prior to touching the light bulbs ensure they are cooled down；



Find the light fixture which is inside the exposed section of the canopy.



Unscrew the light bulb that needs to be replaced and separate the power supply quick joint terminal of the light bulb.



Check the model and parameter of new light bulb newly installed. Connect the power supply quick joint terminal. And replace the old light bulb.



IMPORTANT: Defective bulbs should be replaced immediately.



If the lights still do not work, make sure that the lamps are fitted properly into their housing before you call for technical assistance.



Refit the grease filters.

4.4.FITTING THE CARBON FILTER

If the appliance is being used in recirculation mode then it is necessary to fit carbon filters. This will help to absorb unpleasant odors caused by cooking.

IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE THE

CARBON FILTERS, YOU MUST ENSURE THAT YOU HAVE

DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY.

1. Remove the grease filters.

2. Hook the carbon filter over the pins that are located at the end of the motor.

3. Turn the carbon filter anticlockwise, until you feel it click into place.

 Repeat this process for the second carbon filter. You need to place a carbon filter at either end of the motor.

 Refit the grease filters.

 The carbon filters should be replaced every three months of if they show signs of damage.

4.5.EXTRACTION MODE OR RECIRCULATION MODE

What is the difference between extraction and recirculation modes?

To get optimum performance form your cooker, the air will be taken out of the room via external ducting.

Unfortunately if you live in a flat or the hood is too far from an outside wall, this may not be possible.

The only alternative is to recirculate the air.

In recirculation mode stale air is taken via the grease filter, and passed through a charcoal filter for purification. The air then re-enters the kitchen via an opening in the hood.

What is a charcoal filter and do I need one?

All cooker hoods have a grease filter but if you are using your cooker hood in recirculation mode, then a charcoal filter must be fitted in addition to the grease filter.

5.USE (Speed adjustment .See pictures)

6.SAFETY WARNING



Never let the children operate the machine.



The cooker hood is for home use only, not suitable for barbecue, roast shop and other commercial purpose.



The cooker hood and its filter should be clean regularly in order to keep in good working condition.



Clean the cooker hood according to the instruction manual and keep the unit from danger of burning.



Forbid the direct baking from the gas cooker.



Please keep the kitchen room a good convection.



Before connecting this appliance check that the power supply cord is not damaged. A damage supply cord must be replaced by qualified service personnel only.



There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels



The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels



Regulations concerning the discharge of air have to be fulfilled.



This appliance if not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person slide for their safety.



Children should be supervised to ensure that they do not play with the appliance.



Do not flambé under the range hood.



The range hood is not intended to be installed over a hob having more than four hob elements



This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.



Children should be supervised to ensure that they do not play with the appliance.



The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.



When the range hood and appliances supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).



CAUTION: Accessible parts may become hot when used with cooking appliances.

Electrical Shock Hazard



Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer.



Failure to follow these instructions can result in death, fire, or electrical shock.

7. ABNORMITY AND SOLUTION

Fault Cause Solution

Light on, but motor does not work

Light does not work, motor does not work

Oil leakage

The leaf blocked

The capacitor damaged Replace capacitor

The motor jammed bearing damaged Replace motor

The internal with of motor off or a bad smell from the motor

Replace motor

Beside the above mentioned, check the following:

Light damaged

Power cord looses

One way valve and the air ventilation entrance are not tightly sealed

Leakage from the connection of

U-shaped section and cover

Get rid of the blocking

Replace lights

Connect the wires as per the electric diagram

Take down the one way valve and seal with glue

Take U-shaped section down and seal with soap or paint

Shake of the body The leaf damaged and causes shaking

The motor is not tightly hanged

The body is not tightly hanged

Replace the leaf

Lock the motor tightly

Fixed the body tightly

Insufficient suction

The machine inclines

The distance between the body and the gas top too long

Readjust the distance

Too much ventilation from open doors or windows

Choose a new place and resemble the machine

The fixing screw not tight enough Tighten the hanging screw and make it horizontal

The hanging screw not tight enough

Tighten the hanging screw and make it horizontal

8.ENVIRONMENTAL NOTE

Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse.

This should be undertaken by a competent person.

CONFORMITY TO W.E.E.E DIRECTIVE

This appliance is marked according to the European directive 2002/96/EC on Waste electrical and

Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waster disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchases the product.