Showtec Galactic FX RGB-1000 laser effect Manual
Below you will find brief information for laser effect Galactic FX RGB-1000. This laser effect features a high output and great effects. It is equipped with a built-in microphone for sound-controlled effects, and you can control it via DMX. Use the control panel to select from various built-in effects, adjust sound sensitivity, and set the DMX address. You can also link multiple Galactics together in Master/Slave mode.
advertisement
MANUAL
ENGLISH
Galactic FX RGB-1000 V1
Ordercode: 51343
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Galactic FX RGB-1000
Table of contents
Ordercode: 51343
1
Galactic FX RGB-1000
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
● Showtec Galactic FX RGB-1000
● IEC power cable – 1,75m
● Remote control plug and 2 keys
● User manual
Ordercode: 51343
2
Galactic FX RGB-1000
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
● be qualified
● follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device.
• Never let the power cord come into contact with other cables! Handle the power cord and all connections with the mains with particular caution!
• Never remove warning or informative labels from the unit.
• Never use anything to cover the ground contact.
• Never place any material over the lens.
• Never look directly into the light source.
• Never leave any cables lying around.
• Never aim the laser beam at people or animals!
• Never use the device during thunderstorms, unplug the device immediately.
• Never point a laser at aircraft, this is a federal offense.
• Never point un-terminated laser beams into the sky.
• Never open the laser housing. The high laser power levels inside of the protective housing can start fires, burn skin and will cause instant eye injury.
• Do not insert objects into air vents.
• Do not connect this device to a dimmerpack.
• Do not open the device and do not modify the device.
• Do not point lasers at highly reflective surfaces such as windows, mirrors and shiny metal. Even laser reflections can be hazardous.
• Do not expose the output optic (aperture) to cleaning chemicals.
• Do not use laser if the laser appears to be emitting only one or two beams.
• Do not use laser if housing is damaged or open, or if optics appear damaged in any way.
• Do not operate laser without first reading and understanding all safety and technical data in this manual. Never look into the laser aperture or laser beams.
• Do not switch the device on and off in short intervals, as this would reduce the device’s life.
• Do not shake the device. Avoid brute force when installing or operating the device.
• After set up and prior to public use, test laser to ensure proper function. Do not use the laser if any defect is detected. Do not use, if the laser emits only one or two laser beams rather than dozens/hundreds, as this could indicate damage to the diffraction grating optic, and could allow emission of higher laser levels.
• Only use device indoor, avoid contact with water or other liquids.
• Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
• Only operate the device after having familiarized with its functions.
• Avoid flames and do not put close to flammable liquids or gases.
• Always check the regulations when using a class 4 laser product.
Ordercode: 51343
3
Galactic FX RGB-1000
• Always check and position the laser before anybody enters the room, when the laser is facing an area with people.
• Always keep case closed while operating.
• Always allow free air space of at least 50 cm around the unit for ventilation.
• Always disconnect power from the mains, when device is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
• Make sure that the device is not exposed to extreme heat, moisture or dust.
• Make sure that the available voltage is not higher than stated on the rear panel.
• Make sure that the power cord is never crimped or damaged. Check the device and the power cord from time to time.
• If the external cable is damaged, it has to be replaced by a qualified technician.
• If the lens is obviously damaged, it has to be replaced. So that its functions are not impaired, due to cracks or deep scratches.
• If device is dropped or struck, disconnect mains power supply immediately. Have a qualified engineer inspect for safety before operating.
• If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.
• If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
• For adult use only. Device must be installed out of the reach of children. Never leave the unit running unattended.
• Never attempt to bypass the thermostatic switch or fuses.
• For replacement use fuses of same type and rating only.
• The operation of a class 4 laser show laser is only allowed if the show is controlled by a skilled and well-trained operator familiar with the data included in this manual.
• The user is responsible for correct positioning and operating of the Galactic FX RGB-1000 . The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device.
• This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
• The laser will only work between 15-35ºC.
• After 3 hours working, you must shut off the laser and let the laser diode cool off for 30 minutes, otherwise the laser could be damaged and the warranty becomes void.
• Repairs, servicing and electric connection must be carried out by a qualified technician.
• WARRANTY: Till one year after date of purchase.
Operating Determinations
● This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
● The minimum distance between light-output and the illuminated surface must be more than 1 meter.
● The maximum ambient temperature ta = 35°C must never be exceeded.
● The relative humidity must not exceed 50 % with an ambient temperature of 30° C.
● If this device is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.
● Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Ordercode: 51343
4
Galactic FX RGB-1000
Laser safety for a Class 4 Laser Product
This product is a Class 4 laser with 1220 mW visible output.
Class 4 is the highest and most dangerous class of laser, including all lasers that exceed the Class 3B AEL.
By definition, a class 4 laser can burn the skin, or cause devastating and permanent eye damage as a result of direct, diffuse, specular reflections or indirect beam viewing.
These lasers may ignite combustible materials, and thus may represent a fire risk.
These hazards may also apply to indirect or non-specular reflections of the beam, even from apparently matte surfaces—meaning that great care must be taken to control the beam path.
Class 4 lasers must be equipped with a key switch and a safety interlock.
CAUTION! Only Laser Safety Officers who are officially certified by a regulatory body or authorized training organization are allowed to use class 4 lasers in public. The Laser Safety Officer is responsible for all aspects when using this laser, including following all locally applicable safety laws and regulations. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this laser.
CAUTION: AVOID EXPOSURE TO BEAM: Avoid direct eye contact with laser light. Never intentionally expose your eyes or others to direct laser radiation.
Compliance Statement
Your Galactic Laser has been designed to comply with FDA and IEC Standards for it classification.
The Galactic is a Class 4 laser product.
Laser Safety and Compliance Information
The Galactic is manufactured to comply with the IEC 60825-1 and in accordance with U.S. Food and
Drug Administration (FDA) Standards Listed under FDA Document 21 CFR 1040 and subsequent laser notices.
Product Classification and Manufacturing Label Identification
Laser Classification
Cooling
Laser medium
Output
Beam Diameter
Pulse Data All pulses
Class 4
TE Cooling and Cooling fan wavelength 450 nm / Blue (DPSS), 920mW wavelength 532 nm / Green (DPSS), 110mW wavelength 638 nm / Red (Laser Diode), 190mW
1220 mW
<20mm at aperture
< 4Hz (>0.25sec)
Divergence (each beam) <2 mrad
Divergence (total light) <160 degrees
The legal requirements for using laser entertainment products vary from country to country. The user is responsible for the legal requirements at the location/country of use.
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard
―For Safe Use of Lasers‖, available from www.laserinstitute.org
. Many local governments, corporations, agencies, military and others, require all lasers to be used under the guidelines of ANSI Z136.1. Laser
Display guidance can be obtained via the International Laser Display Association, www.laserist.org
.
CAUTION: The use of corrective eye wear or optics for viewing at distances such as telescopes or binoculars within a distance of 100mm may pose an eye hazard.
This laser product is a Class 4 laser and has an Interlocked housing.
Ordercode: 51343
5
Galactic FX RGB-1000
There are no user serviceable parts inside. Tampering or removing warranty seals will void your products limited warranty.
Combo label with the Product Model Number, Serial Number,
Date of Manufacturing, Laser Light Warning Label, Warranty
Void Label and Interlocked Housing Label
Proper Usage Safety and Compliance Information
According to FDA Regulations you should operate this product as stated on the left.
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
● If the Galactic is lowered from the ceiling or high joists, professional trussing systems have to be used.
● Use a clamp to mount the Galactic, with the mounting-bracket, to the trussing system.
● The Galactic must never be fixed swinging freely in the room.
● The installation must always be secured with a safety attachment, e.g. an appropriate safety net or safety-cable.
● When rigging, derigging or servicing the Galactic, always make sure, that the area below the installation place is blocked and staying in the area is forbidden.
Ordercode: 51343
6
Galactic FX RGB-1000
The Galactic can be placed on a flat stage floor or mounted to any kind of truss with a clamp.
Improper installation can cause serious damage to people and property !
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
L
N
EU Cable
BROWN
BLUE
UK Cable
RED
BLACK
US Cable
YELLOW/COPPER
SILVER
Pin
PHASE
NEUTRAL
YELLOW/GREEN GREEN GREEN
Make sure that the device is always connected properly to the earth!
PROTECTIVE GROUND
Improper installation can cause serious damage to people and property!
Ordercode: 51343
7
Galactic FX RGB-1000
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [email protected] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping. Transportation damage has to be reported to us within one day after receipt of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement, regardless of the agreement of which the obligation is resulting.
Ordercode: 51343
8
Galactic FX RGB-1000
Description of the device
Features
The Showtec Galactic FS RGB-1000 is a laser effect with high output and great effects.
● Power Input: AC 100-240V, 60/50Hz
● Power Consumption: 70 Watt
● Beam Diameter <20mm at aperture
● Laser Class: 4
● Laser Modulation: TTL
● Laser Safety: EN/IEC 60825-1 Ed 2, 2007-03
● Laser Color: Red, Green, Yellow, Blue, Purple, Cyan, White
● Laser Power: 1220mW: wavelength 450 nm / Blue (DPSS), 920mW wavelength 532 nm / Green (DPSS), 110mW wavelength 638 nm / Red (Laser Diode), 190mW
● Scan Angle: +/-80°
● Control Modes: Auto, Sound, Master/Slave, DMX
● Divergence (each beam) <2 mrad; Divergence (total light) <160 degrees
● 3-pin DMX In and 3-pin DMX Out
● 3-digit LED Display
● Compact strong metal housing
● Sound-controlled via built-in microphone
● 18 DMX Channels
● Safety Features: Key switch, Interlock
● Fuse 1,6AL/250V
● Dimensions: 290 x 260 x 205 mm (LxWxH)
● Weight: 4 kg
● Accessories: 2 Keys, Interlock remote plug
Overview
01) Lens
02) Mounting bracket
03) Adjustment screw
04) LED power indicator
05) LED sound control indicator
Ordercode: 51343
9
Fig. 01
Galactic FX RGB-1000
Backside
Fig. 02
06) Cooling fan
07) Safety eye
08) ILDA Input
09) ILDA Through
10) LED Display + control buttons
11) Built-in microphone
12) 3-pin DMX signal connector (IN)
13) Ground/Earth connection
14) 3-pin DMX signal connector (OUT)
15) IEC Power connector 100-240VAC
16) Fuse 1,6AL/250V
17) Power switch ON/OFF
18) Interlock
19) Remote control plug
NOTE: Knowledge of DMX is required to fully utilize this unit.
Installation
Remove all packing materials from the Galactic. Check if all foam and plastic padding is removed.
Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply. The device can be sound-controlled as it is equipped with a built-in microphone.
Ordercode: 51343
10
Galactic FX RGB-1000
The Interlock plug/remote plug and safety keys are included in the box.
The interlock is the ―included-in-the-box‖ successor for the optional remote interlock (51316)
They should be kept with the Galactic laser !!!
The following safety precautions should be followed:
● The interlock plug should be placed on the backside (19) of your
Galactic laser.
● The keys should be put into the lock (18) of your Galactic laser.
Warning
Exclusion of liability
Be aware that in some countries, there are additional regulations, regarding the use of laser devices.
Therefore, we strongly advise you to verify your national laws with your authorities: We do not take any responsibility for eventual discrepancies, changes or adaptions regarding lawful use of laser devices.
Ordercode: 51343
11
Galactic FX RGB-1000
Control Modes
There are 4 modes: Built-in programs (stand-alone)
Sound-controlled
Master/Slave
DMX-512 (18CH)
One Galactic (Stand-alone)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Galactic is not connected by a DMX-cable, it functions as a stand-alone device.
05) Please see page 17 for more information about the Built-in auto programs.
One Galactic (Sound-controlled)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Galactic is not connected with a DMX-cable, it functions as a stand-alone device.
05) Please see page 17 for more information about the Sound-controlled mode.
Multiple Galactics (Master/Slave Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Galactics.
The pins: 01) Earth
02) Signal (-)
03) Signal (+)
05) Link the units as shown in Fig. 03, connect a DMX signal cable from the first unit's DMX "out" socket to the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. You can use the same functions on the master device as described on page 17 (Built-in or Sound-controlled).
This means on the master device you can set your desired operation Mode and all slave devices will react the same as the master device.
Multiple Galactics Master/Slave Set Up
Ordercode: 51343
12
Fig. 03
Galactic FX RGB-1000
Multiple Galactics (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-p XLR cable to connect the Galactics and other devices.
05) Link the units as shown in Fig. 04, Connect a DMX signal cable from the first unit's DMX "out" socket to the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
06) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the other end of the mains power cord into proper electric power supply sockets, starting with the first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Galactics DMX Set Up
Ordercode: 51343
Note: Link all cables before connecting electric power
13
Fig. 04
Galactic FX RGB-1000
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
DAP Audio Certified DMX Data Cables
• DAP Audio cable for all-round use. bal. XLR/M 3 p. > XLR/F 3 p.
Ordercode FL01150 (1,5m.), FL013 (3m.), FL016 (6m.), FL0110 (10m.), FL0115 (15m.), FL0120 (20m.).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5m.), FL713 (3m.), FL716 (6m.), FL7110 (10m.).
The Galactic can be operated with a controller in control mode or without the controller in stand-alone
mode.
Ordercode: 51343
14
Galactic FX RGB-1000
Control Panel
A) LED display
B) FUNC button
C) UP button
D) DOWN button
E) ENTER button
Fig. 05
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the first channel from which the Galactic will respond to the controller.
Please note when you use the controller, the unit has 18 channels.
When using multiple Galactics, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Galactics should be 1(001); the DMX address of the second
Galactic should be 1+18=19 (019); the DMX address of the third Galactic should be 19+18=37 (037), etc.
Please, make sure that you do not have any overlapping channels in order to control each Galactic correctly.
If two or more Galactics are addressed similarly, they will work similarly.
Controlling:
After having addressed all Galactic fixtures, you may now start operating these via your lighting controller.
Note: After switching on, the Galactic will automatically detect whether DMX-512 data is received or not.
If there is no data received at the DMX-input, the ―LED― on the control panel will not flash.
The problem may be:
• The XLR cable from the controller is not connected with the input of the Galactic.
• The controller is switched off or defective, the cable or connector is detective, or the signal wires are swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure proper transmission on the DMX data link.
Ordercode: 51343
15
Galactic FX RGB-1000
Menu Overview
Ordercode: 51343
16
Galactic FX RGB-1000
Main Menu Options
Built-in auto and sound-controlled effects
Sound Sensitivity
DMX Mode
Master/Slave Mode
Horizontal/Mirror Flip Mode
You can only change a certain setting when the display is blinking.
If you cannot change a certain value, please press the FUNC button once and then change the value.
1. Built-in Auto Effects
01) Press the FUNC button until one of the following names appears on the screen:
02) While the display is blinking, press the Up and Down buttons to choose the desired effect.
03) Press the ENTER button to confirm your choice.
The software will now run a pre-programmed laser show. There are 9 built-in auto effects + 9 of their sound-controlled counterparts.
2. Sound Sensitivity
In this menu you can set sound sensitivity of the device.
01) Press the FUNC button until the display shows .
02) Press the Up and Down buttons to increase or decrease the sound sensitivity value.
0 = off, 1-9 = from low to high sound sensitivity.
03) Press the ENTER button to save changes.
3. DMX Mode
In this menu you can set the DMX address.
01) Press the FUNC button until the display shows .
02) Use the Up and Down buttons to select the required address between
04) Press the ENTER button to save changes.
4. Master/Slave Mode
.
01) Press the FUNC button until the display shows
02) Press the ENTER button to confirm.
.
03) The device is now operating in Slave mode and it will react the same as the master device.
Ordercode: 51343
17
Galactic FX RGB-1000
5. Horizontal/Mirror Flip Mode
In this menu you can choose the way in which your laser show is going to be displayed.
01) Press the FUNC button until one of the following names appears on the display:
Horizontal Flip
Horizontal Flip + Mirror Flip
Normal View
Normal View + Mirror Flip
02) Press the Up and Down buttons you to choose your preferred display setting.
03) Press the ENTER button to confirm your choice.
Ordercode: 51343
18
Galactic FX RGB-1000
DMX Channels
6 channels (Basic)
Channel 1 – Control modes
0-18 Laser off
19-30
31-42
Auto shows
3D Auto shows
43-54
55-66
Only when Ch 1 is set between 235-244, Ch 2-6 will function.
Auto beam show
Lumia effect
67-78
79-90
91-102
103-114
115-126
127-138
139-150
151-162
Effect 1
Effect 2
Effect 3
Effect 4
Effect 5
Auto shows, sound-controlled
3D Auto show, sound-controlled
Auto beam show, sound-controlled
163-174
175-186
187-198
199-210
211-222
223-234
Lumia effect, sound-controlled
Effect 1, sound-controlled
Effect 2, sound-controlled
Effect 3, sound-controlled
Effect 4, sound-controlled
Effect 5, sound-controlled
235-244
245-255
Manual effect 1
Manual effect 2
Channel 2 – Rotation
0-127
128-133
Counterclockwise rotation, from slow to fast
Static
134-255 Clockwise rotation, from slow to fast
Channel 3 – Color
0-7
8-15
Multicolor
Red
16-23
24-31
32-39
40-47
48-55
56-65
66-207
Green
Red and Green
Blue
Blue and Red
Blue and Green
Red, Green and Blue
Sequential color change, from slow to fast
208-255 Strobe, from slow to fast
Channel 4 – Horizontal movement
0-127 Manual adjustment, from right to left
128-255
Channel 5
Not functional
Auto movement, from right to left
Channel 6 – Vertical movement
0-127 Manual adjustment
128-255 Auto vertical movement
Ordercode: 51343
19
Galactic FX RGB-1000
18 channels (Advanced)
Channel 1 – Control modes
0-18 Laser off
19-30
31-42
43-54
55-66
67-78
79-90
91-102
103-114
Auto shows
3D Auto shows
Only when Ch 1 is set between 245-255, Ch 2-18 will function.
Auto beam show
Lumia effect
Effect 1
Effect 2
Effect 3
Effect 4
115-126
127-138
139-150
151-162
163-174
175-186
Effect 5
Auto shows, sound-controlled
3D Auto show, sound-controlled
Auto beam show, sound-controlled
Lumia effect, sound-controlled
Effect 1, sound-controlled
187-198
199-210
211-222
223-234
Effect 2, sound-controlled
Effect 3, sound-controlled
Effect 4, sound-controlled
Effect 5, sound-controlled
235-244
245-255
Manual effect 1
Manual effect 2
Channel 2 – Pattern progression
0-51
52-103
104-155
156-207
Basic form
2 nd
form
3 rd
form
4 th
form
208-255 5 th
form
Channel 3 – Patterns Ch 2 and Ch 3 are connected to each other.
The full pattern chart (see page 22).
Choose your preferred pattern by adjusting the value of Channel 3. Subsequently, adjust the value of
Channel 2 to gain access to secondary patterns.
Channel 4 – Laser show effects
0-31
32-63
64-95
96-127
128-159
160-191
192-255
3D shape
Multicolor
Water effect
Multiplication effect
Multicolor
Multiplication (pattern in the middle + circular multiplication)
Multicolor (bright)
Channel 5 – 3D Rotation effect
0-4 Static
5-127
128-133
Ch 4 needs to be set between 0-31 for Ch 5 to work.
Counterclockwise rotation, from slow to fast
Static
134-255 Clockwise rotation, from slow to fast
Channel 6 – Color
0-7 Purple
8-15 Red
Ordercode: 51343
20
Galactic FX RGB-1000
16-23
24-31
32-39
40-47
48-55
56-63
64-159
160-207
208-255
Green
Yellow
Blue
Purple
Cyan
White
Sequential color change, from slow to fast
Progressive color change, from slow to fast
Strobe, from slow to fast
Channel 7 – Line drawing effect
0-123
124-127
128-255
Manual drawing
Blackout
Auto drawing, from slow to fast
Channel 8 – Zoom
0-127
128-144
Manual zoom out
Fast auto zoom out
145-209
210-255
Fast auto zoom in
Fast zoom in and zoom out
Channel 9
Not functional
Channel 10 – X-axis rotation
0-127 Manual rotation
128-255
Channel 11
Not functional
Automatic rotation
Channel 12 – Y-axis rotation
0-127
128-255
Manual rotation
Automatic rotation
Channel 13
Not functional
Channel 14 – Clockwise rotation
0-127 Manual rotation
128-255
Channel 15
Not functional
Automatic rotation
Channel 16 – Horizontal movement, from left to right
0-127 Manual adjustment
128-255
Channel 17
Automatic movement
Not functional
Channel 18 – Vertical movement, from the bottom to the top
0-127 Manual adjustment
128-255 Automatic movement
Ordercode: 51343
21
Galactic FX RGB-1000
Patterns
Ordercode: 51343
22
Galactic FX RGB-1000
Maintenance
The Showtec Galactic requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light-output will be significantly reduced.
Disconnect the mains power supply and then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft cloth. Do not use alcohol or solvents. The front glass panel will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the light-output very quickly.
Do not immerse in liquid.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
The operator has to make sure that safety-relating and machine-technical installations are to be inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are to be inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the fuse burns out, the product will not function whatsoever. If this happens, follow the directions below.
01) Unplug the unit from electric power source.
02) Insert a screwdriver into the slot in the fuse cover. Gently pry up the fuse cover. The fuse will come out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse cover. Be sure to use a fuse of the same type and specification. See the product specification label for details.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit operates properly, do not carry out following steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Response: Suspect three potential problem areas as: the power supply, the laser, the fuse.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The laser. Return the Galactic to your Showtec dealer.
03) The fuse. Replace the fuse. See page 23 for replacing the fuse.
04) If all of the above appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the Galactic, as this may damage the unit and the warranty will become void.
06) Return the device to your Showtec dealer.
No Response to DMX
Response: Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light effect to a qualified technician.
Ordercode: 51343
23
Galactic FX RGB-1000
Problem
One or more fixtures do not function at all
Fixtures reset correctly, but all respond erratically or not at all to the controller.
Probable cause(s)
No power to the fixture.
Primary fuse blown..
The controller is not connected.
3-pin XLR Out of the controller does not match XLR Out of the first fixture on the link (i.e. signal is reversed).
Fixtures reset correctly, but some respond erratically or not at all to the controller.
Shutter closes suddenly
No light or laser cuts out intermittently
Remedy
● Check that power is switched on and cables are plugged in.
● Replace fuse.
● Connect controller.
● Install a phase reversing cable between the controller and the first fixture on the link.
Poor data quality ● Check data quality. If much lower than
100 percent, the problem may be a bad data link connection, poor quality or broken cables, missing termination plug, or a defective fixture disturbing the link.
● Inspect connections and cables. Bad data link connection
Data link not terminated with 120
Ohm termination plug.
●
Correct poor connections. Repair or replace damaged cables.
Insert termination plug in output jack of the last fixture on the link.
Incorrect addressing of the fixtures. ● Check address setting.
One of the fixtures is defective and disturbs data transmission on the link.
● Bypass one fixture at a time until normal operation is regained: unplug both connectors and connect them directly together.
3-pin XLR Out on the fixtures does not match (pins 2 and 3 reversed).
The laser diode has lost its index position and the fixture is resetting the effect.
Fixture is too hot.
● Have the defective fixture serviced by a qualified technician.
● Install a phase-reversing cable between the fixtures or swap pin 2 and 3 in the fixture, that behaves erratically.
● Contact a technician for servicing the problem persists.
Laser damaged
● Allow fixture to cool.
● Make sure air vents at control panel and front lens are not blocked.
● Turn up the air conditioning .
● Disconnect fixture and return to your dealer.
The power supply settings do not match local AC voltage and frequency.
● Disconnect fixture. Check settings and correct if necessary.
Ordercode: 51343
24
Galactic FX RGB-1000
Product Specifications
Model:
Input Voltage:
Continuous Power:
Fuse:
Dimensions:
Weight:
Operation and Programming
Signal pin OUT:
Set Up and Addressing:
DMX Channels:
Signal input:
Signal output:
Electro-mechanical effects
Laser Class:
Laser Power:
Galactic FX RGB-1000
AC 100-240V, 60/50Hz
70 Watt
1.6AL/250V
290 x 260 x 205 mm (LxWxH)
4 kg pin 1 earth, pin 2 (-), pin 3 (+)
Red LED display for all settings
6 and 18 channels
3-pin DMX signal connector IN
3-pin DMX signal connector OUT
Light Source:
Strobe:
Cooling:
Beam diameter:
Pulse Data, All Pulses:
Divergence (each beam):
Divergence (total light):
Safety Features:
DMX-control:
Control Modes:
Housing:
4
1220mW (190mW 638nm Red, 110mW 532nm Green,
920mW 450nm Blue)
1 x 5W LED
0-20Hz
Cooling fans and TE Cooling
<20mm at aperture
<4Hz (>0.25 sec)
<2 mrad;
<160 degrees
Key switch, Interlock
Via standard DMX-controller
Built-in Programs, Manual, Master/Slave, Sound
Black Metal & Flame-retardant plastic
Connections:
Laser Safety:
Max. ambient temperature t a
:
Minimum distance:
Minimum distance from flammable surfaces:
Minimum distance to lighted object:
Dedicated IEC Power & Data connector
EN/IEC 60825-1 Ed 2, 2007-03
40°C
0.5m
1m
Design and product specifications are subject to change without prior notice.
Website: www.Showtec.info
Email: [email protected]
Ordercode: 51343
25
Galactic FX RGB-1000
Dimensions
Ordercode: 51343
26
©2015 Showtec
advertisement
Key Features
- High output
- Sound-controlled effects
- DMX control
- Built-in auto effects
- Master/Slave mode
- 18 DMX channels