QSFP28 Test Adapter User Manual

QSFP28 Test Adapter User Manual
QSFP28 Test Adapter User Manual (Preliminary)
QSFP28
Test Adapter
User Manual (Preliminary)
P a g e |1
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Table of Contents
Introduction ..................................................................................................................................... 3
Product Inspection .......................................................................................................................... 5
The QSFP28 Test Adapter Care and Handling Precautions ............................................................. 6
General Test Adapter, Cable, and Connector .................................................................................. 8
Handling and Storage .................................................................................................................. 8
Visual Inspection.......................................................................................................................... 8
Cleaning ....................................................................................................................................... 8
Making Connections .................................................................................................................... 8
Electrostatic Discharge Information ................................................................................................ 9
User Model .................................................................................................................................... 10
Calibration Through De-Embedding (Preliminary) ........................................................................ 13
Mechanical and Environmental Specifications.............................................................................. 14
Electrical Specifications ................................................................................................................. 20
QSFP28 Test Adapter Reference Information ............................................................................... 31
Wilder Technologies, LLC – Limited Warranty .............................................................................. 32
Wilder Technologies, LLC – Terms & Conditions of Sale ............................................................... 33
Compliance with Environmental Legislation ................................................................................. 34
WEEE Compliance Statement .................................................................................................... 34
Glossary of Terms .......................................................................................................................... 35
Addendum A – QSFP28 Receptacle Test Adapter with Power Sinking ......................................... 36
Power Sinking Version Receptacle Test Adapter....................................................................... 36
Index .............................................................................................................................................. 37
P a g e |2
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Introduction
This user’s guide documents the QSFP28 Plug and Receptacle Test Adapters (QSFP28TPA100G-HCB-P and QSFP28-TPA100G-MCB-R). The two test adapter types, shown in Figures 1
and 2, test QSFP28 interface cables, hosts, and modules to the requirements of the SFF-8665
specification. Addendum A also provides reference information as it pertains to the Power
Sinking version of the Receptacle Test Adapter (QSFP28-TPA100GH-MCB-R).
The - HCB-P and -MCB-R test adapter assemblies allow easy access, via SMA connections, to
measure or inject data signals.
NOTE: To avoid damaging the cables, use the handling techniques
described in the Care and Handling section before making any
connections or configuring a test setup.
Always use a static-safe workstation when performing tests, as
explained in the “Electrostatic Discharge Information” section.
Low-Speed
Connector
50 Ohm RF Termination (Male
Shown, 1 of up to 16 shown.
Optional Accessory)
DC Block (1 of up to 16 shown.
Optional Accessory. Note:
Actual DC Block may differ
from part shown.)
16 SMAs (Female
Shown) for HighSpeed Testing
QSFP28 Plug
Connector
Assembly
Figure 1. The QSFP28 HCB Test Adapter tests to the requirements of the Host Compliance Board (Plug)
(Note: Coaxial cables shown are illustrated shorter than those used in the test adapter. The
coaxial cables are configuration dependent and may be terminated with different SMA
connectors than what is shown.)
P a g e |3
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
DC Block (1 of up to 16
shown. Optional Accessory.
Note: Actual DC Block may
differ from part shown.)
50 Ohm RF Termination
(Male Shown, 1 of up to 16
Shown. Optional Accessory)
Low-Speed
Connector
16 SMAs (Female
Shown) for HighSpeed Testing
QSFP28
Receptacle
Figure 2. The QSFP28 MCB Test Adapter tests to the requirements of the Module Compliance Board
(Receptacle). (Note: Coaxial cables shown are illustrated shorter than those used in the test
adapter. The coaxial cables are configuration dependent and may be terminated with
different SMA connectors than what is shown.)
NOTE: The metal shell of both the plug (QSFP28-TPA100G-HCB-P)
and receptacle (QSFP28-TPA100G-MCB-R) connectors tie high-speed
ground to chassis ground.
The low-speed 12-position receptacle and plug connectors are keyed and latching (Molex
part number 43645-1200 for the plug TPA and 43650-1204 for the receptacle TPA). The mating
connector housings and contact pins for 26-30awg wire are Molex part number 43640-1201
for the 12-position housing and 43031-0011 for the plug contacts used with the plug TPA, and
Molex part number 43645-1200 for the 12-position housing and 43030-0011 for the receptacle
contacts used with the receptacle TPA. Replacement parts can be purchased through Molex
distributors.
NOTE: The receiver SMA connections for QSFP28 are normally AC
coupled. The QSFP28 plug and receptacle TPAs do NOT have internal
DC Blocks. This allows for parametric testing through the TPAs.
Normal testing may require DC Blocks (May be optionally ordered
from Wilder Technologies). Refer to the Electrical Specifications
section of this document for DC Block performance parameters.
P a g e |4
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Product Inspection
Upon receiving the QSFP28-TPA100G from Wilder Technologies, perform the following
product inspection:
•
Inspect the outer shipping container, foam-lined instrument case, and product for damage.
Retain the outer cardboard shipping container until the contents of the shipment have been
inspected for completeness and the product has been checked mechanically and electrically.
Use the foam-lined instrument-case for secure storage of the Wilder Technologies QSFP28
Test Adapter when not in use.
•
Locate the shipping list and verify that all items ordered were received.
•
In the unlikely event that the product is defective or incomplete, the “Limited Warranty”
section discusses how to contact Wilder Technologies for technical assistance and/or how to
package the product for return.
P a g e |5
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
The QSFP28 Test Adapter Care and Handling Precautions
The QSFP28 Test Adapter requires careful handling to avoid damage. Improper handling
techniques, or using too small a cable bend radius, can damage the coaxial cable connections
within the adapter housing or the cables themselves. This can occur at any point along the
cable. To achieve optimum performance and to prolong the QSFP28 TPA’s life, observe the
following handling precautions:
•
CAUTION 1: Avoid Torque Forces (Twisting)
While individual coaxial cables within the test adapter have some rotational freedom,
twisting the QSFP28-TPA100G as a unit, with one end held stationary, may damage or
severely degrade performance. Adherence to Caution 5 (below) helps to avoid twisting.
•
CAUTION 2: Avoid Sharp Cable Bends
Never bend coaxial cables into a radius of 26 mm (1-inch) or less. Never bend cables
greater than 90°. Single or multiple cable bends must be kept within this limit. Bending the
QSFP28-TPA100G cables less than a 26mm (1-Inch) radius will permanently damage or
severely degrade test adapter performance.
•
CAUTION 3: Avoid Cable Tension (Pull Forces)
Never apply tension (pull forces) to an individual coaxial cable that is greater than 2.3 kg
(5 lbs.). To avoid applying tension, always place accessories and equipment on a surface
that allows adjustment to eliminate tension on the QSFP28-TPA100G and cables. Use
adjustable elevation stands or apparatus to accurately place and support the QSFP28 TPA.
•
CAUTION 4: Connect the QSFP28-TPA100G First
To prevent twisting, bending, or applying tension to the coaxial cables when connecting a
QSFP28 TPA, always attach the QSFP28-TPA100G to the device under test (DUT) or cable
under test before attaching any SMA connectors. Carefully align the QSFP28 connectors and
then gently push the connectors together until fully seated.
If the QSFP28-TPA100G must be turned or twisted to make connection to the DUT, avoid
using the QSFP28-TPA100G housing alone to make this occur. Try to distribute the torque
forces along the length of the test setup and cabling. If this is not possible, it is
recommended to first loosen or disconnect the SMA connections at the QSFP28 TPA, make
the connection to the DUT and then re-tighten or attach the test equipment leads.
NOTE: Only grip the test adapter housing when inserting or
extracting the QSFP28-TPA100G to or from the DUT. Pulling directly
on the QSFP28-TPA100G cables or using them to insert the QSFP28TPA100G may cause damage.
•
CAUTION 5: Carefully Make SMA Connections
To connect the QSFP28-TPA100G SMA connectors, follow these steps:
1.
Hold the cable stationary by grasping the cable at the black heat-shrink section
near the SMA connector.
2.
Insert the mating SMA barrel and hand-tighten the free-spinning SMA nut onto the
connector while avoiding pulling, bending, or twisting the QSFP28-TPA100G coaxial
cable.
P a g e |6
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
3.
The QSFP28-TPA100G SMA connectors have flats that accept an open-end 1/4-inch
or 5/16-inch wrench, depending on configuration. When attaching instrument
cables to the QSFP28 TPA100G, it is recommended that the QSFP28 TPA100G SMA
connectors be mechanically held and the test leads be tightened to the equipment
manufacturer’s torque recommendations, normally 5 in-lbs, using an open-end
torque wrench.
If the test set-up requires repositioning, first loosen or disconnect the SMA connections to
avoid twisting, bending, or tension.
NOTE: A drop in signal amplitude by half or 6dB during the testing of
a channel may indicate that a cable has been mechanically pulled
free of coaxial cable connections internal to the assembly. This could
be determined by checking if the cable has any lateral play relative
to the TPA. This would only occur when the TPA has exceeded the
pull force as specified within the mechanical specification. If the
cable cannot be re-seated, the test adapter will need to be sent back
to the factory for service.
•
CAUTION 6: Independently Support Instrument Cables or Accessories
Excessive weight from instrument cables and/or accessories connected to the QSFP28
TPA100G can cause damage or affect the test adapter performance. Be sure to provide
appropriate means to support and stabilize all test set-up components.
•
CAUTION 7: ESD Sensitivity
The QSFP28 test adapters are passive components and are not in themselves sensitive to
electrostatic discharge. However, when an active DUT is installed, that device becomes
susceptible to ESD. Observe proper ESD precautions, further discussed later in this
document.
P a g e |7
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
General Test Adapter, Cable, and Connector
Observing simple precautions can ensure accurate and reliable measurements.
Handling and Storage
Before each use of the QSFP28 TPA100G, ensure that all connectors are clean. Handle all
cables carefully and store the QSFP28-TPA100G in the foam-lined instrument case when not in
use, if possible. Do not set connectors contact end down. Install the SMA protective end caps
when the QSFP28-TPA100G is not in use.
Visual Inspection
Be sure to inspect all cables carefully before making a connection. Inspect all cables for
metal particles, scratches, deformed threads, dents, or bent, broken, or misaligned center
conductors. Do not use damaged cables.
Cleaning
If necessary, clean the connectors using low-pressure (less than 60 PSI) compressed air or
nitrogen with an effective oil-vapor filter and condensation trap. Clean the cable threads, if
necessary, using a lint-free swab or cleaning cloth moistened with isopropyl alcohol. Always
completely dry a connector before use. Do not use abrasives to clean the connectors. Reinspect connectors, making sure no particles or residue remains.
Making Connections
Before making any connections, review the “Care and Handling Precautions” section. Follow
these guidelines when making connections:
•
•
•
•
•
•
•
Align cables carefully
Make preliminary connection lightly
To tighten, turn connector nut only
Do not apply bending force to cable
Do not over-tighten preliminary connections
Do not twist or screw-in cables
Use an appropriately sized torque wrench, and do not tighten past the “break” point of the
torque wrench (normally 5 inch pounds)
P a g e |8
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Electrostatic Discharge Information
Protection against electrostatic discharge (ESD) is essential while connecting, inspecting, or
cleaning the QSFP28-TPA100G test adapter and connectors attached to a static-sensitive circuit
(such as those found in test sets).
Electrostatic discharge can damage or destroy electronic components. Be sure to perform all
work on electronic assemblies at a static-safe work station, using two types of ESD protection:
•
•
Conductive table-mat and wrist-strap combination
Conductive floor-mat and heel-strap combination
When used together, both of these types provide a significant level of ESD protection. Used
alone, the table-mat and wrist-strap combination provide adequate ESD protection. To ensure
user safety, the static-safe accessories must provide at least 1 MΩ of isolation from ground.
Acceptable ESD accessories may be purchased from a local supplier.
WARNING: These techniques for a static-safe work station should
not be used when working on circuitry with a voltage potential
greater than 500 volts.
P a g e |9
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
User Model
The QSFP28 TPAs are capable of performing to the requirements of SFF-8665, limited only by
the specifications, environmental, care and handling of this document.
In the case where the laboratory source or load is not used in the test, it must be replaced
with RF terminations on each unused signal. (RF terminators are optionally offered by Wilder
Technologies.)
The following examples are suggestions for possible testing setups.
In this first example, a QSFP28-TPA100G-MCB-R is used to test a QSFP28 Module:
P a g e | 10
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
The second example shows a QSFP28-TPA100G-HCB-P is used to test a host:
In the case where the laboratory source or load is not used in the test, it must be replaced
with RF terminations on each unused signal. (RF terminators are optionally offered by Wilder
Technologies.)
P a g e | 11
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
The third example shows two QSFP28-TPA100G-MCB-R’s used for testing a QSFP28 cable:
P a g e | 12
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Calibration Through De-Embedding (Preliminary)
The QSFP28 Test Adapters are fully passive components. Therefore, calibration
compensating for the losses must occur within the test instrumentation that drives the QSFP28
Receivers or looks at the response of the QSFP28 Transmitters.
The QSFP28-TPA’s have Touchstone S4P files for de-embedding the electrical length and
losses within the TPA up to the QSFP28 connector interface pads. (Contact Wilder
Technologies, support@wilder-tech.com, to obtain a copy of the S4P files.) The Touchstone S4P
files enable the test engineer to compensate for the last four of the following six repeatable,
systematic errors that occur when moving the reference plane:
•
•
•
•
•
•
Signal leakage effects: Directivity errors
Signal leakage effects: Crosstalk errors
Reflection effects: Source Impedance Mismatching errors
Reflection effects: Load Impedance Mismatching errors
Bandwidth effects: Receiver Transmission in Test Equipment errors
Bandwidth effects: Receiver Reflection-tracking in Test Equipment errors
These errors are corrected on each port. Refer to the Instrument Manual for instructions on
the instrument’s specific de-embedding process.
NOTE: The reference plane is the boundary, both physically and
electrically, between the calibrated and uncalibrated portions of
the circuit. Everything outside the reference plane is considered
part of the DUT. Any instrument that does not use calibration or deembedding of the test fixture defines the DUT as the total of
externally connected components. If the de-embedding file is not
used, all of the QSFP28-TPA and associated coaxial cables, as well as
cables connecting the TPA assembly to the test instrument, would be
a part of the DUT.
Non-repeatable errors, such as drift or random errors, can be reduced but not corrected.
Drift errors aggregate over time or with environmental changes such as temperature shift. To
eliminate drift errors, perform an instrumentation-level calibration.
A random error cannot be corrected through calibration since the error occurred randomly.
Random errors are typically associated with either test instrument noise or test repeatability
problems. Reduce test instrument noise by increasing source power, lowering the IF
bandwidth, or averaging results over multiple sweeps. Reduce test repeatability problems
through the use of a torque wrench or, again, by averaging over multiple sweeps.
P a g e | 13
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Mechanical and Environmental Specifications
NOTE: All specifications in this manual are subject to change.
Table 1. General Specifications
ITEM
DESCRIPTION
Usage Environment
Controlled indoor environment
Receptacle Test Adapter Length (w/standard
cables, end to end)
406.40 mm +/- 2 mm (16.00 inches +/- .08 inches)
(Characteristic)
199.40 mm +/- 2 mm (7.85 inches +/- .08 inches)
(Characteristic)
Receptacle Test Adapter Housing Dimensions
95.25 x 93.98 x 74.93 (3.75 x 3.70 x 2.95 inches) (L, W, H)
Operating Temperature
0°C to +55°C (32°F to +131°F) (Characteristic)
Storage Temperature
-40°C to +70°C (-40°F to +158°F) (Characteristic)
Plug Test Adapter Length (w/standard cables)
QSFP28-TPA100G-HCB-P and QSFP28-TPA100G-MCB-R Cable Pinout
The QSFP28-TPA100G cables provide sixteen SMA connectors (four lanes of primary
differential TX and RX). Labels clearly mark each cable or connector. The following figure refers
to the pin-description table for the plug connector.
Low-Speed
Connector (See
Table 3 & 4)
Pin 1 End (Ref)
16 SMAs for HighSpeed Testing
(Female Shown)
QSFP28 Plug
Connector
(See Table 4)
Color-Coded and Imprinted Markings
(Large Colored = Channel Number)
(Short White = Transmit Side)
(Short Red = Positive Polarity)
See Table 2 & 4
Figure 3. Cable Connectors (QSFP28-TPA100G-HCB-P shown)
(Note: Coaxial cables shown are illustrated shorter than those used in the test adapter. The
coaxial cables are configuration dependent and may be terminated with different SMA
connectors than what is shown.)
P a g e | 14
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
The following figure refers to the pin-description table for the receptacle connector.
Color-Coded and Imprinted Markings
(Large Colored = Channel Number)
(Short White = Transmit Side)
(Short Red = Positive Polarity)
See Table 2 & 4
Low-Speed
Connector
(See Table 3 and 4)
16 SMAs for HighSpeed Testing
QSFP28
Receptacle
Connector
(See Table 4)
Figure 4. Cable Connectors (QSFP28-TPA100G-MCB-R shown)
(Note: Coaxial cables shown are illustrated shorter than those used in the test adapter.
The coaxial cables are configuration dependent and may be terminated with different
SMA connectors than what is shown.)
P a g e | 15
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Table 2. SMA Cable Connectors (High-Speed)
LABEL
COLOR ID FOR DIFFERENTIAL PAIR
DESCRIPTION
RX4+
Red
Lane 4 Receiver positive
RX4-
Red
Lane 4 Receiver negative
RX3+
Green
Lane 3 Receiver positive
RX3-
Green
Lane 3 Receiver negative
RX2+
Blue
Lane 2 Receiver positive
RX2-
Blue
Lane 2 Receiver negative
RX1+
Yellow
Lane 1 Receiver positive
RX1-
Yellow
Lane 1 Receiver negative
TX4+
Red with White band
Lane 4 Transmitter positive
TX4-
Red with White band
Lane 4 Transmitter negative
TX3+
Green with White band
Lane 3 Transmitter positive
TX3-
Green with White band
Lane 3 Transmitter negative
TX2+
Blue with White band
Lane 2 Transmitter positive
TX2-
Blue with White band
Lane 2 Transmitter negative
TX1+
Yellow with White band
Lane 1 Transmitter positive
TX1-
Yellow with White band
Lane 1 Transmitter negative
P a g e | 16
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Table 3. QSFP28-TPA100G 12-Position Cable Connector (Low-Speed)
LABEL
PIN NO.
COLOR ID FOR HCB/MCB
DESCRIPTION
GND
Pin 1
Black/NA
Signal (RF Ground) and Supply (Power) Common
MPL
Pin 2
Black/NA
Module Present
ITL
Pin 3
Black/NA
Interrupt
SDA
Pin 4
Black/NA
SDA, I2C Data for DDC
SCL
Pin 5
Black/NA
SCL, I2C Clock for DDC
RSL
Pin 6
Black/NA
Module Reset
MSL
Pin 7
Black/NA
Module Select
LPM
Pin 8
Black/NA
Low Power Mode
VCC
Pin 9
Black/NA
Vcc1 module power supply (+3.3V)
VCR
Pin 10
Black/NA
VccR, module receiver power supply (+3.3V)
VCT
Pin 11
Black/NA
VccT, module transmitter power supply (+3.3V)
GND
Pin 12
Black/NA
Signal (RF Ground) and Supply (Power) Common
P a g e | 17
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Table 4. QSFP28-TPA100G Plug and Receptacle Pin Assignments
Connector
Pin Number
Destination
Number
(HCB/MCB)
Color ID for Data
Line Polarity
Color Identification
(HCB/MCB)
Ground
1
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
Tx2n
2
Tx2-
Black
White/Blue
Tx2p
3
Tx2+
Red
White/Blue
Ground
4
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
Tx4n
5
Tx4-
Black
White/Red
Tx4p
6
Tx4+
Red
White/Red
Ground
7
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
MSL
8
P2/J2 Pin 7
N/A
Black Insulation/NA
RSL
9
P2/J2 Pin 6
N/A
Black Insulation/NA
VccR (Filtered)
10
P2/J2 Pin 10
N/A
Black Insulation/NA
SCL
11
P2/J2 Pin 5
N/A
Black Insulation/NA
SDA
12
P2/J2 Pin 4
N/A
Black Insulation/NA
Ground
13
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
Rx3p
14
Rx3+
Red
Green
Rx3n
15
Rx3-
Black
Green
Ground
16
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
Rx1p
17
Rx1+
Red
Yellow
Rx1n
18
Rx1-
Black
Yellow
Ground
19
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
Ground
20
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
Rx2n
21
Rx2-
Black
Blue
Rx2p
22
Rx2+
Red
Blue
Ground
23
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
Rx4n
24
Rx4-
Black
Red
Rx4p
25
Rx4+
Red
Red
Ground
26
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
MPL
27
P2/J2 Pin 2
N/A
Black Insulation/NA
Pin Description
P a g e | 18
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
ITL
28
P2/J2 Pin 3
N/A
Black Insulation/NA
VccT (Filtered)
29
P2/J2 Pin 11
N/A
Black Insulation/NA
Vcc1 (Filtered)
30
P2/J2 Pin 9
N/A
Black Insulation/NA
LPM
31
P2/J2 Pin 8
N/A
Black Insulation/NA
Ground
32
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
Tx3p
33
Tx3+
Red
White/Green
Tx3n
34
Tx3-
Black
White/Green
Ground
35
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
Tx1p
36
Tx1+
Red
White/Yellow
Tx1n
37
Tx1-
Black
White/Yellow
Ground
38
P2/J2 Pin 1, Pin 12
N/A
Black Insulation/NA
P a g e | 19
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Electrical Specifications
NOTE: All specifications in this manual are subject to change.
Table 5. Electrical Specifications (TPA)
SPECIFICATION
MIN
TYP
MAX
NOTES
SDD21 (dB), at 12.89 GHz
-1.7
HCB TPA without Connector and Pad.
SDD21 (dB), at 7.03 GHz
-1.2
HCB TPA without Connector and Pad.
SDD21 (dB), at 12.89 GHz
-TBD
MCB TPA without Connector and Pad.
SDD21 (dB), at 7.03 GHz
-TBD
MCB TPA without Connector and Pad.
SDD21 (dB), at 12.89 GHz
-4.0
Mated HCB and MCB TPAs with Connectors and
Pads.
SDD21 (dB), at 7.03 GHz
-2.35
Mated HCB and MCB TPAs with Connectors and
Pads.
SDD11 (dB), at 12.89 GHz
-9
Mated HCB and MCB TPAs with Connectors and
Pads.
SDD11 (dB), at 7.03 GHz
-16
Mated HCB and MCB TPAs with Connectors and
Pads.
SDC21 (dB), at 12.89 GHz
-20.0
Mated HCB and MCB TPAs with Connectors and
Pads.
SDC21 (dB), at 7.03 GHz
-25.0
Mated HCB and MCB TPAs with Connectors and
Pads.
Differential Impedance (ohms),
34 ps Rise Time, 20 –80%
90
110
All Differential Pairs, Receptacle and Plug,
excluding QSFP28 connector.
Differential Impedance (ohms),
34 ps Rise Time, 20 –80%
80
120
All Differential Pairs, Receptacle and Plug,
including QSFP28 connector.
Impedance (ohms), 34 ps Rise
Time, 20 –80%
45
55
Single-ended signals within differential pairs,
Receptacle and Plug, excluding QSFP28
connector.
Intra-pair Skew (ps)
-3?
3?
All Differential Pairs, Receptacle and Plug.
Inter-pair Skew (ps)
-6
6
All Differential Pairs, Receptacle and Plug.
NEXT (dB), at 10 GHz
-30
-40
Single aggressor, with QSFP28 connector, mated
HCB to MCB, with standard coaxial cables and
terminations.
P a g e | 20
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Table 6. Electrical Specifications (Optional External DC Block) as Supplied by Wilder Technologies
SPECIFICATION
MIN
Insertion Loss (dB),
at 100 kHz - 12.4 GHz
at 12.4 - 26.5 GHz
TYP
NOTES
0.50
0.75
VSWR, 7kHz TO 26.5 GHz
Upper -3dB Bandwidth (GHz)
MAX
1.35
26.5
Lower -3dB Bandwidth (kHz)
7
Voltage
100
Volts
Max.
In-Line Capacitance (µF)
0.474
Impedance (Ohms)
50
Table 7. Electrical Specifications (Optional RF Termination) as Supplied by Wilder Technologies
SPECIFICATION
MIN
TYP
VSWR,
DC to 4 GHz
4 to 12.4 GHz
12.4 to 18 GHz
Frequency Range (GHz)
NOTES
1.05
1.15
1.20
DC
18
Power Dissipation (Watts)
Impedance (Ohms)
MAX
2
Power derates linearly from 100% ≤ 25°C to
10% @ 125°C
50
P a g e | 21
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Figure 5. Typical mated pair 28 Gb/s eye diagram.
Figure 6. Typical mated pair 28 Gb/s eye data.
P a g e | 22
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Figure 7. Typical mated pair 25 Gb/s eye diagram.
Figure 8. Typical mated pair 25 Gb/s eye data.
P a g e | 23
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Figure 9. Typical mated pair balanced insertion loss.
Figure 10. Available S4Ps showing balanced insertion loss of HCB without connector, MCB without
connector, and HCB through MCB without connectors.
P a g e | 24
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Figure 11. Typical mated pair balanced return loss.
Figure 12. Available S4Ps showing balanced return loss of HCB without connector, MCB without connector,
and HCB through MCB without connectors.
P a g e | 25
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Figure 13. Typical differential TDR of TX channels of QSFP28-TPA100G-HCB-P connected to QSFP28TPA100G-MCB-R at 34 ps Rise Time (20-80%) (Measured at 50 ps 10-90%).
P a g e | 26
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Figure 14. Typical differential TDR of RX channels of QSFP28-TPA100G-HCB-P connected to QSFP28TPA100G-MCB-R at 34 ps Rise Time (20-80%) (Measured at 50 ps 10-90%).
P a g e | 27
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Figure 15. Typical mated pair common mode return loss.
Figure 16. Typical mated pair differential to common mode conversion.
P a g e | 28
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Figure 17. Typical Differential NEXT, Plug TPA, with mated connectors, adjacent differential pairs, both
transmit and receive terminated at both ends.
Figure 18. Typical Differential NEXT, Receptacle TPA, with mated connectors, adjacent differential
pairs, both transmit and receive terminated at both ends.
P a g e | 29
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Figure 19. Typical Differential FEXT, with mated connectors, adjacent differential pairs, both transmit
and receive terminated at both ends.
P a g e | 30
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
QSFP28 Test Adapter Reference Information
This section contains a schematic diagram of the QSFP28-TPA100G-MCB-R Power
Connections.
Figure 20. QSFP28-TPA100G-MCB-R Power Connections
P a g e | 31
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Wilder Technologies, LLC – Limited Warranty
Wilder Technologies, LLC warrants that each Test Adapter, 1) is free from defects in materials and workmanship and,
2) conforms to Wilder Technologies specifications for a period of 12 months, with the exceptions of the HDMIA2
(HDMI v2.0), HDMID2 (HDMI v2.0), SFP28, QSFP28, and QSFP+ 100G Test Adapters, whereby are warranted for a
period of 6 months, all other aspects of the Wilder Technologies, LLC warranty apply.
See Consumable and Fragile Material Warranty for exceptions to the 12 month warranty
The warranty period for a Test Adapter is a specified, fixed period commencing on the date of ship from Wilder
Technologies, LLC. If you did not purchase your Test Adapter directly from Wilder Technologies, LLC, the serial number
and a valid proof of purchase will be required to establish your purchase date. If you do not have a valid proof of
purchase, the warranty period will be measured from the date of ship from Wilder Technologies, LLC.
If, during the warranty period, the Test Adapter is not in good working order, Wilder Technologies, LLC will, at its
option, repair or replace it at no additional charge, except as is set forth below. In some cases, the replacement Test
Adapter may not be new and may have been previously installed. Regardless of the Test Adapter’s production status,
Wilder Technologies, LLC appropriate warranty terms apply.
Consumable and Fragile Material Warranty
Wilder Technologies, LLC warrants that consumable materials and all fragile materials supplied by Wilder Technologies,
LLC either as part of an instrument or system, or supplied separately, will be free from defects in material and
workmanship at the time of shipment.
Extent of Warranty
The warranty does not cover the repair or exchange of a Test Adapter resulting from misuse, accident, modification,
unsuitable physical or operating environment, improper maintenance by you, or failure caused by a product for which
Wilder Technologies, LLC is not responsible. The warranty is voided by removal or alteration of Test Adapter or parts
identification labels. The initial three months are unconditional; the remaining months excludes plugs, receptacles and
SMA connectors. Connectors are wear items and excluded from the warranty after the initial three months.
These warranties are your exclusive warranties and replace all other warranties or conditions, express or implied,
including but not limited to, the implied warranties or conditions or merchantability and fitness for a particular
purpose. These warranties give you specific legal rights and you may also have other rights which vary from
jurisdiction to jurisdiction. Some jurisdictions do not allow the exclusion or limitation of express or implied
warranties, so the above exclusion or limitation may not apply to you. In that event, such warranties are limited in
duration to the warranty period. No warranties apply after that period.
Items Not Covered by Warranty
Wilder Technologies, LLC does not warrant uninterrupted or error–free operation of a Test Adapter.
Any technical or other support provided for a Test Adapter under warranty, such as assistance via telephone with
"how–to" questions and those regarding Test Adapter set-up and installation, will be provided WITHOUT WARRANTIES
OF ANY KIND.
Warranty Service
Warranty service may be obtained from Wilder Technologies, LLC by returning a Wilder Technologies, LLC Returns
Material Authorization and the Test Adapter to Wilder Technologies, LLC during the warranty period. To obtain RMA
number, contact support@wilder-tech.com.
You may be required to present proof of purchase or other similar proof of warranty entitlement. You are responsible
for any associated transportation charges, duties and insurance between you and Wilder Technologies, LLC. In all
instances, you must ship Test Adapters in Wilder Technologies, LLC approved packaging. Information on packaging
guidelines can be found at: www.wilder-tech.com. Wilder Technologies, LLC will ship repaired or replacement Test
Adapter Delivery Duty Prepaid (DDP) and will pay for return shipment. You will receive title to the repaired or
replacement Test Adapter and you will be the importer of record.
P a g e | 32
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Wilder Technologies, LLC – Terms & Conditions of Sale
1.
Other Documents: This Agreement may NOT be altered, supplemented, or amended by the use of any other
document(s) unless otherwise agreed to in a written agreement signed by both you and Wilder Technologies, LLC. If
you do not receive an invoice or acknowledgement in the mail, via e-mail, or with your Product, information about your
purchase may be obtained at support@wilder-tech.com or by contacting your sales representative.
2.
Payment Terms, Orders, Quotes, Interest: Terms of payment are within Wilder Technologies, LLC's sole discretion, and
unless otherwise agreed to by Wilder Technologies, LLC, payment must be received by Wilder Technologies, LLC prior
to Wilder Technologies, LLC's acceptance of an order. Payment for the products will be made by credit card, wire
transfer, or some other prearranged payment method unless credit terms have been agreed to by Wilder Technologies,
LLC. Invoices are due and payable within the time period noted on your invoice, measured from the date of the invoice.
Wilder Technologies, LLC may invoice parts of an order separately. Your order is subject to cancellation by Wilder
Technologies, LLC, in Wilder Technologies, LLC's sole discretion. Unless you and Wilder Technologies, LLC have agreed
to a different discount, Wilder Technologies, LLC's standard pricing policy for Wilder Technologies, LLC-branded
systems, which includes hardware, software and services in one discounted price, allocates the discount off list price
applicable to the service portion of the system to be equal to the overall calculated percentage discount off list price on
the entire system. Wilder Technologies, LLC is not responsible for pricing, typographical, or other errors in any offer by
Wilder Technologies, LLC and reserves the right to cancel any orders resulting from such errors.
3.
Shipping Charges; Taxes; Title; Risk of Loss: Shipping, handling, duties and tariffs are additional unless otherwise
expressly indicated at the time of sale. Title to products passes from Wilder Technologies, LLC to Customer on shipment
from Wilder Technologies, LLC's facility. Loss or damage that occurs during shipping by a carrier selected by Wilder
Technologies, LLC is Wilder Technologies, LLC's responsibility. Loss or damage that occurs during shipping by a carrier
selected by you is your responsibility. You must notify Wilder Technologies, LLC within 7 days of the date of your
invoice or acknowledgement if you believe any part of your purchase is missing, wrong or damaged. Unless you provide
Wilder Technologies, LLC with a valid and correct tax exemption certificate applicable to your purchase of Product and
the Product ship-to location, you are responsible for sales and other taxes associated with the order. Shipping dates
are estimates only.
4.
WARRANTY: WILDER TECHNOLOGIES, LLC, warrants that the item(s) manufactured under the Buyer's contract shall be
free from defects in materials and workmanship furnished by WILDER TECHNOLOGIES, LLC, and shall conform to the
applicable drawings and specifications. WILDER TECHNOLOGIES, LLC’S liability herein, for breach of warranty, contract
or negligence in manufacturing, shall be limited to repair or replacement. Repair or replacement of defective items will
be applicable only if the Buyer notifies WILDER TECHNOLOGIES, LLC, by written notice within 30-days of delivery. All
claims shall be addressed to: support@wilder-tech.com or WILDER TECHNOLOGIES, LLC, 6101A East 18th Street,
Vancouver, Washington 98661 U.S.A.; ATTENTION: Customer Service Manager. WILDER TECHNOLOGIES, LLC, reserves
the right to inspect at the Buyer's plant all items claimed to be defective or nonconforming prior to authorizing their
return. WILDER TECHNOLOGIES, LLC, assumes no liability for the results of the use of its components in conjunction
with other electric, electronic or mechanical components, circuits and/or systems. The foregoing constitutes the sole
and exclusive remedy of the Buyer and the exclusive liability of WILDER TECHNOLOGIES, LLC, and is IN LIEU OF ANY
AND ALL OTHER WARRANTIES, STATUTORY, IMPLIED OR EXPRESSED AS TO MERCHANTABILITY, FITNESS FOR THE
PURPOSE SOLD, DESCRIPTION, QUALITY, and PRODUCTIVENESS OR ANY OTHER MATTER. Without limiting the
foregoing, in no event shall WILDER TECHNOLOGIES, LLC, be liable for loss of use, profit or other collateral, or for
special and/or consequential damages.
5.
RETURNED GOODS: WILDER TECHNOLOGIES, LLC, will accept only those goods for return that have been authorized for
return. All goods authorized for return shall be assigned a Returned Material Authorization (RMA) Number. The RMA
Number shall be clearly marked on the shipping container(s) and all documentation accompanying the goods
authorized for return. The RMA Number shall be assigned by WILDER TECHNOLOGIES, LLC pursuant to the conditions
set forth in Paragraph 4, WARRANTY.
6.
UNITED STATES GOVERNMENT CONTRACTS: In the event this offer is accepted under Government contract, WILDER
TECHNOLOGIES, LLC, agrees to accept clauses required by Government regulations and to waive WILDER
TECHNOLOGIES, LLC conditions inconsistent therewith. WILDER TECHNOLOGIES, LLC, certifies that it is a regular
manufacturer or dealer of the goods and/or services offered herein and that the prices offered do not exceed those
charged to any customer for like quantities, services or materials under the same conditions.
P a g e | 33
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Compliance with Environmental Legislation
Wilder Technologies, LLC, is dedicated to complying with the requirements of all applicable
environmental legislation and regulations, including appropriate recycling and/or disposal of
our products.
WEEE Compliance Statement
The European Union adopted Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE), with requirements that went into effect August 13, 2005. WEEE is intended
to reduce the disposal of waste from electrical and electronic equipment by establishing
guidelines for prevention, reuse, recycling and recovery.
Wilder Technologies has practices and processes in place to conform to the requirements in
this important Directive.
In support of our environmental goals, effective January 1st, 2009 Wilder Technologies, LLC
has partnered with EG Metals Inc. – Metal and Electronics Recycling of Hillsboro, Oregon,
www.egmetalrecycling.com, to recycle our obsolete and electronic waste in accordance with
the European Union Directive 2002/96/EC on waste electrical and electronic equipment
("WEEE Directive").
As a service to our customers, Wilder Technologies is also available for managing the proper
recycling and/or disposal of all Wilder Technologies products that have reached the end of their
useful life. For further information and return instructions, contact support@wilder-tech.com.
P a g e | 34
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Glossary of Terms
TERMINOLOGY
DEFINITION
Aggressor
A signal imposed on a system (i.e., cable assembly) to measure response on
other signal carriers.
Decibel (dB)
Ten times the common logarithm (i.e. log10) of the ratio of relative powers.
Far-end crosstalk or
FEXT
Crosstalk that is propagated in a disturbed channel in the same direction as
the propagation of a signal in the aggressor channel. The terminals of the
aggressor channel and the victim channel are usually close to each other.
Informative
The designation of a test that is not required for compliance.
Insertion loss
The ratio, expressed in dB, of incident power to delivered power.
Near-end crosstalk or
NEXT
Crosstalk that is propagated in a disturbed channel in the opposite
direction as the propagation of a signal in the aggressor channel. The
terminals of the aggressor channel and the victim channel are usually close
to each other.
Normative
The designation of a test that is required for compliance.
Return Loss
The ratio, expressed in dB, of incident power to reflected power.
QSFP28
28 Gbps 4X Pluggable Transceiver (Quad Small Form Factor Pluggable)
QSFP28 Host
The QSFP28 Host is the fixed end of the connection supporting IEEE 802.3.
QSFP28 Module
The QSFP28 Module is the moveable end of the connection supporting IEEE
802.3.
QSFP28 TPA
QSFP28 Test Point Access. A specialized assembly that interfaces to a
QSFP28 host or module and enables access of signals for measurement or
stimulation.
Victim
A signal carrier on a system that has a response imposed on it by other
signals in the system.
P a g e | 35
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Addendum A – QSFP28 Receptacle Test Adapter with Power
Sinking
This addendum provides reference information as it relates to the QSFP28-TPA100GH-MCB-R
(QSFP28 Receptacle Test Adapter with Power Sinking) version of QSFP28 Receptacle Test
Adapters.
Power Sinking Version Receptacle Test Adapter
Features of the QSFP28-TPA100GH-MCB-R Test Adapter are Illustrated below.
Color-Coded and Imprinted Markings
(Large Colored = Channel Number)
(Short White = Transmit Side)
(Short Red = Positive Polarity)
See Previous Section, Table 2 & 4
16 SMAs for HighSpeed Testing
Low-Speed Connector
Not Shown
(See Previous Section,
Table 3 and 4)
QSFP28 Receptacle Connector
with Integral Heat Sink
(See Previous Section Table 4)
Figure A-1. The QSFP28-TPA100GH-MCB-R Test Adapter (Receptacle TPA with Power Sinking)
(Note: Coaxial cables shown are illustrated shorter than those used in the test adapter.
The coaxial cables are configuration dependent and may be terminated with different
SMA connectors than what is shown.)
P a g e | 36
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
QSFP28 Test Adapter User Manual (Preliminary)
Index
AC coupled, 4
Addendum A – QSFP28-TPA100GH-MCB-R Test
Adapter, 36
Cable Bend Limits, 6
Cable Tension (Pull Forces), 6
Cable Twisting (Torque), 6
Calibration Through De-Embedding, 13
Care and Handling, 6
Cleaning, 8
Compliance
WEEE, 34
Connections
QSFP28-TPA100G to DUT, 6
SMA, 6, 7
Crosstalk Errors, 13
DC Blocks, 3, 4, 10, 11, 21
Directivity Errors, 13
Drift Errors, 13
DUT, 13
Electrical Specifications, 20
Electrostatic Discharge Information (ESD), 9
Environmental Changes, 13
Errors
Crosstalk, 13
Directivity, 13
Drift, 13
Load Impedance Mismatching, 13
Random, 13
Receiver Reflection-tracking in Test Equipment, 13
Receiver Transmission in Test Equipment, 13
Source Impedance Mismatching, 13
ESD protection, 9
ESD Sensitivity, 7
Figures
Cable Connectors, 14, 15, 36
QSFP28-TPA100GH-MCB-R Test Adapter, 36
QSFP28-TPA100G-MCB-R Test Adapter Power
Connections, 31
The QSFP28 HCB Test Adapter (Plug), 3, 14
The QSFP28 MCB Test Adapter (Receptacle), 4, 15
The QSFP28-TPA100GH-MCB-R Test Adapter
(Receptacle with Power Sinking), 36
Glossary, 35
Handling and Storage, 8
Load Impedance Mismatching Errors, 13
Low-Speed Connector, 4
Low-Speed Connector Part Numbers, 4
Making Connections, 8
Mechanical and Environmental Specifications, 14
Molex part numbers, 4
Power Sinking Version, 36
Product Inspection, 5
Product Return, 5
Pull Force, 6, 7
QSFP28-TPA100G Reference Information, 31
QSFP28-TPA100G-HCB-P Cable Pinout, 14
QSFP28-TPA100G-HCB-P Plug TPA Testing a Host, 11
QSFP28-TPA100G-MCB -R Testing a QSFP28 Module,
10
QSFP28-TPA100G-MCB-R Cable Pinout, 14
QSFP28-TPA100G-MCB-R’s Testing a QSFP28 Cable,
12
Random Errors, 13
Receiver Reflection-Tracking in Test Equip. Errors, 13
Receiver Transmission in Test Equipment Errors, 13
RF Terminations, 3, 4, 10, 11, 21
Secure Storage, 5
SFF Specification, 3
SMA cables, 14
Source Impedance Mismatching Errors, 13
Support, 13, 33
Supporting Instrument Cables or Accessories, 7
Tables
Electrical Specifications (External DC Block), 21
Electrical Specifications (RF Termination), 21
Electrical Specifications (TPA), 20
General Specifications, 14
QSFP28-TPA100G 12-Position Cable Connector, 17
QSFP28-TPA100G Plug & Recept. Pin Assignments,
18
SMA Cable Connectors (High-Speed), 16
Terms and Conditions of Sale, 33
Test Instrument Noise, 13
Test Repeatability Problems, 13
User Model Examples, 10, 11, 12
Visual Inspection, 8
Warranty, 32
Web Sites
support@wilder-tech.com, 32, 33
www.egmetalrecycling.com, 34
www.wilder-tech.com, 32
WEEE, 34
P a g e | 37
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A (Preliminary)
Visit our website at www.wilder-tech.com
Wilder Technologies, LLC
6101A East 18th Street
Vancouver, WA 98661
Phone: 360-859-3041
Fax: 360-859-3105
www.wilder-tech.com
©2015 Wilder Technologies, LLC
Document No. 910-0045-000 Rev. A
Created: 8/26/2015 Updated: 10/23/2015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising