Network Camera
Network Camera
Quick Operation Guide
ENGLISH
Quick Operation Guide of Network Camera
1
Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate
to contact the dealer.
Quick Operation Guide of Network Camera
2
This manual may contain several technical incorrect places or printing errors, and the content is
subject to change without notice. The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security
or signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined
in UL’s Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or
reliability of the security or signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
Quick Operation Guide of Network Camera
3
Table of Contents
Chapter 1 Appearance Description .......................................................................... 1
1.1 Appearance Description of Box Camera ......................................................... 1
1.1.1 Box Camera I ............................................................................................. 1
1.1.2 Box Camera II ............................................................................................ 2
1.1.3 Box Camera III............................................................................................ 5
1.2 Appearance Description of Dome Camera ..................................................... 7
1.2.1 Dome Camera I .......................................................................................... 7
1.2.2 Dome Camera II ......................................................................................... 9
1.2.3 Dome Camera III ...................................................................................... 10
1.2.4 Dome Camera IV...................................................................................... 12
1.3 Appearance Description of Bullet Camera.................................................... 13
1.3.1 Bullet Camera I ........................................................................................ 13
1.3.2 Bullet Camera II ....................................................................................... 14
1.4 Appearance Description of Cube Camera..................................................... 15
1.4.1 Cube Camera I ......................................................................................... 15
1.4.2 Cube Camera II ........................................................................................ 16
1.5 Appearance Description of Mini Dome Camera............................................ 19
Chapter 2 Setting the Network Camera over the LAN ............................................ 21
Chapter 3 Accessing via Web Browsers .................................................................. 25
1
Quick Operation Guide of Network Camera
Chapter 1 Appearance Description
There are ten physical structures of network cameras, Box camera I, Box camera II, Box camera III,
Dome camera I, Dome camera II, Dome camera III, Dome camera IV, Bullet Camera, Cube Camera
and Mini Dome Camera.
1.1 Appearance Description of Box Camera
1.1.1 Box Camera I
Camera description:
Figure 1-1 Overview
Table 1-1 Description
No.
1
2
3
4
5
6
7
8
9
10
11
12
Description
CS Lens mount
Back focus ring
Auto-iris interface
10M/100M self-adaptive Ethernet interface
AUDIO IN: Audio input interface
AUDIO OUT: Audio output interface
SD: SD card slot
VIDEO OUT: Video output interface
Power supply interface
PWR: Power LED indicator
D+, D-: RS-485 interface
Ground
1A, 1B: Alarm output interface
2
Quick Operation Guide of Network Camera
13
IN, G: Alarm input interface
Note: The type of auto-iris interface is shown in Figure 1-2, and the definition of each pin is shown
below:
Figure 1-2 Auto-iris Interface
Table 1-2 Pins
DC-driven
1
Damp2
Damp+
3
Drive+
4
DriveDamp+, Damp-, Drive+ and Drive- pins are used when the auto-iris is driven by DC.
Camera wiring Diagram:
Figure 1-3 Wiring Diagram
1.1.2 Box Camera II
Camera description:
3
Quick Operation Guide of Network Camera
Figure 1-4 Overview
Figure 1-5 Overview
Figure 1-6 Overview
Table 1-3 Description
No.
1
Description
CS Lens mount
4
Quick Operation Guide of Network Camera
2
Auto-iris interface
3
Bracket mounting holes
4
F1+ F1-, F2+ F2- ,F3+ F3-: Alarm output interface
5
T1,T2,T3, T4,GND: Alarm input interface
6
D+, D-: RS-485 interface
7
10M/100M self-adaptive Ethernet interface
8
VIDEO OUT/HDMI: Video output interface
9
RESET: Reset button
10
TXD, RXD, GND: RS-232 interface
11
Power supply interface
12
POWER: Power LED indicator
13
SD: SD card slot
14
AUDIO IN: Audio input interface
15
AUDIO OUT: Audio output interface
16
Ground
Notes:
 After the powering on of the camera, pressing and holding the RESET button for about 10
seconds can reset all the parameters to the default settings.
 The type of auto-iris interface is shown in Figure 1-7, and the definition of each pin is shown
below:
Figure 1-7 Auto-iris Interface
Table 1-4 Pins
DC-driven
1
Damp2
Damp+
3
Drive+
4
DriveDamp+, Damp-, Drive+ and Drive- pins are used when the auto-iris is driven by DC.
Camera wiring Diagram:
5
Quick Operation Guide of Network Camera
Figure 1-8 Wiring Diagram
1.1.3 Box Camera III
Camera description:
Figure 1-9 Overview
Table 1-5 Description
No.
1
Description
Lens mount
6
Quick Operation Guide of Network Camera
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Back focus ring
SD card slot
Auto-iris interface
10M/100M self-adaptive Ethernet interface
VIDEO OUT: Video output interface
AUDIO OUT: Audio output interface
POWER: Power LED indicator
Power supply interface
MIC IN: Audio input interface
D+, D-: RS-485 interface
IN, G: Alarm input interface
1A, 1B: Alarm output interface
Ground
RESET: Reset button
Notes:
 After the powering on of the camera, pressing and holding the RESET button for about 10
seconds can reset all the parameters to the default settings.
 The type of auto-iris interface is shown in Figure 1-10, and the definition of each pin is shown
below:
Figure 1-10 Auto-iris Interface
Table 1-6 Pins
DC-driven
1
Damp2
Damp+
3
Drive+
4
DriveDamp+, Damp-, Drive+ and Drive- pins are used when the auto-iris is driven by DC.
Camera wiring Diagram:
Quick Operation Guide of Network Camera
Figure 1-11 Wiring Diagram
1.2 Appearance Description of Dome Camera
1.2.1 Dome Camera I
Camera description:
7
8
Quick Operation Guide of Network Camera
Figure 1-12 Overview
Table 1-7 Description
No.
1
2
3
4
5
6
Description
Video output interface
Power LED indicator
DIP switch
10M/100M self-adaptive Ethernet interface
D+, D-: RS-485 interface
Alarm IN: Alarm input interface
Alarm OUT: Alarm output interface
AIN: Audio input interface
AOUT: Audio output interface
Power supply interface
7
8
The function of positions 1-5 of DIP switch is shown below:
Position
ON
OFF
Function
1
2
3
4
5
Camera wiring Diagram:
SHARP: Sharpness
AES: Auto Shutter
BLC: Back Light Compensation
FL: Anti-flicker
NAGC: Normal AGC
SOFT
AI: Auto Iris
OFF
ON
SAGC: Special AGC
9
Quick Operation Guide of Network Camera
Figure 1-13 Wiring Diagram
1.2.2 Dome Camera II
Camera description:
Figure 1-1 Overview
Table 1-1 Description
10
Quick Operation Guide of Network Camera
No.
1
2
3
4
5
6
Description
10M/100M self-adaptive Ethernet interface
AUDIO IN: Audio input interface
AUDIO OUT: Audio output interface
D+, D-: RS-485 interface
IN, G: Alarm input interface
1A, 1B: Alarm output interface
Power supply interface
Camera wiring Diagram:
Figure 1-2 Wiring Diagram
1.2.3 Dome Camera III
Camera description:
Figure 1-3 Overview
11
Quick Operation Guide of Network Camera
Table 1-2 Description
No.
Description
1
10M/100M self-adaptive Ethernet interface
2
INITIAL SET: Reset button
3
AUDIO OUT: Audio output interface
4
MIC IN: Audio input interface
5
D+, D-: RS-485 interface
6
1A, 1B, 2A, 2B: Alarm output interface
7
IN1, GND, IN2, GND: Alarm input interface
8
Power supply interface
Note: After the powering on of the camera, pressing and holding the INITIAL SET button for about
10 seconds can reset all the parameters to the default settings.
Camera wiring Diagram:
Figure 1-4 Wiring Diagram
12
Quick Operation Guide of Network Camera
1.2.4 Dome Camera IV
Camera description:
9
8
7
Figure 1-5 Overview
Table 1-3 Description
No.
Description
1
Video output interface
2
LINK: Indicator is solid yellow when network is connected.
3
ACT: Indicator flashes blue when network connection is functioning properly.
4
PWR: Indicator is solid red when the device is powered on.
5
Micro SD slot
6
RESET: Reset button
7
10M/100M self-adaptive Ethernet interface
8
Power supply interface
9
Extended interface
Notes:
 The extended interface can be connected to alarm input/output interface, audio input/output
13
Quick Operation Guide of Network Camera
interface, RS-485 interface, etc.

After the powering on of the camera, pressing and holding the RESET button for about 10
seconds can reset all the parameters to the default settings.
Camera wiring Diagram:
Figure 1-6 Wiring Diagram
1.3 Appearance Description of Bullet Camera
1.3.1 Bullet Camera I
Camera description:
Figure 1-7 Overview
Figure 1-8 Overview
14
Quick Operation Guide of Network Camera
Table 1-4 Description
No.
1
2
3
4
5
Description
10M/100M self-adaptive Ethernet interface
Power supply interface
IN, G: Alarm input interface
1A, 1B: Alarm output interface
D+, D-: RS-485 interface
AUDIO IN, G: Audio input interface
AUDIO OUT, G: Audio output interface
Camera wiring Diagram:
Figure 1-9 Wiring Diagram
1.3.2 Bullet Camera II
Camera description:
1
2
Figure 1-10 Overview
15
Quick Operation Guide of Network Camera
4
3
Figure 1-11 Overview
Table 1-5 Description
No.
1
2
3
4
Description
10M/100M self-adaptive Ethernet interface
Power supply
Sun shade
Adjusting screw
1.4 Appearance Description of Cube Camera
1.4.1 Cube Camera I
Camera description:
9
2
6
7
1
8
3
4
5
Figure 1-12 Overview
Table 1-6 Description
No.
1
2
3
10
11
Description
Microphone
Infrared light (Optional)
Micro SD card slot
16
Quick Operation Guide of Network Camera
4
LINK: Network status LED indicator.
LED indicator is solid yellow when network connection is functioning
properly.
Power LED indicator, It is solid red when power is applied to the unit.
Lens
ETHERNET: 10M / 100M self-adaptive Ethernet interface
RESET: Reset button
Speaker
Power supply interface
Screw hole, used to fix the camera to the bracket
5
6
7
8
9
10
11
Note:
After the powering on of the camera, pressing and holding the RESET button for about 10 seconds
can reset all the parameters to the default settings.
Camera wiring Diagram:
Figure 1-13 Wiring Diagram
1.4.2 Cube Camera II
Camera description:
11
1
10
2
15
9
3
12
16
6
7
8
4
5
13
14
17
Quick Operation Guide of Network Camera
Figure 1-14 Overview
Table 1-7 Description
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Description
Photosensitive resistance
Infrared light
PIR sensor
Microphone
Lens
Alarm: Indicator is solid red when the camera is armed with PIR and
access control and it is solid blue when the camera is unarmed.
Indicator flashes blue when movement or presence is detected in
its field of view.
Link: Indicator flashes orange when network connection is
functioning properly.
Tri-axial adjustment bracket
USB interface
Battery
Speaker
RESET: Reset button
Micro SD card slot
Power supply interface
10M / 100M self-adaptive Ethernet interface & PoE
Note:
After the powering on of the camera, pressing and holding the RESET button for about 10 seconds
can reset all the parameters to the default settings.
Camera wiring diagram:
Figure 1-15 Wiring Diagram
Quick Operation Guide of Network Camera
18
19
Quick Operation Guide of Network Camera
1.5 Appearance Description of Mini Dome Camera
Camera description:
Figure 1-16 Overview
Table 1-8 Description
No.
1
2
3
4
5
6
7
8
Description
Cover
Lens
P: Power LED indicator, It is solid red when power is applied to the unit.
Base plate
Set screw hole
Set screw of lens
S & L: Network status LED indicator.
When the network is connected, the “S” LED is solid yellow, while the “L” LED
flashes orange.
RESET: Reset button.
Note:
After the powering on of the camera, pressing and holding the RESET button for about 10 seconds
can reset all the parameters to the default settings.
Camera wiring Diagram:
Quick Operation Guide of Network Camera
Figure 1-17 Wiring Diagram
20
21
Quick Operation Guide of Network Camera
Chapter 2 Setting the Network Camera over
the LAN
Purpose:
To view and configure the camera via LAN (Local Area Network), you need to connect the network
camera in the same subnet with your PC. Then install the SADP or iVMS-4200 software to search
and change the IP of network camera.

The following figure shows the cable connection of a network camera and a PC:
Figure 2-1 Wiring over LAN

Set the IP address of the camera for accessing via LAN.
Steps:
1.
To get the IP address, you can choose either of the following methods:

Use SADP, a software tool which can automatically detect network camera in the LAN and
list the device information like IP address, subnet mask, port number, device serial number,
device version, etc., shown in Figure 2-2.

Use iVMS-4200 software and to list the online devices. Please refer to the user manual of
client software for detailed information.
2.
Change the IP address and subnet mask to the same subnet as of your PC.
Refer to the following introduction to set IP address with SADP software:
 Search active devices online
Search online devices automatically:
After launch the SADP software, it automatically searches the online devices every 15
seconds from the subnet where your computer locates. It displays the total number
22
Quick Operation Guide of Network Camera
and information of the searched devices in the Online Devices interface. Device
information including the device type, IP address, port number, gateway, etc. will be
displayed.
Figure 2-2 Searching Online Devices
Note: Device can be searched and displayed in the list in 15 seconds after it goes online;
it will be removed from the list in 45 seconds after it goes offline.
Search online devices manually:
You can also click
to refresh the online device list manually. The newly
searched devices will be added to the list.
Note: You can click
can click
or
on each column heading to order the information; you
to show the device table and hide the network parameter panel on the
right side, or click
to show the network parameter panel.
 Modify device information
Steps:
1) Select the device to be modified in the device list as shown in Figure 2-3. The network
Quick Operation Guide of Network Camera
23
parameters of the device will be displayed in the Modify Network Parameters panel on
the right side as shown in Figure 2-4.
2) Edit the modifiable network parameters, e.g. IP address and port number.
3) Enter the password of the admin account of the device in the Password field and click
to save the changes.
Figure 2-3 Select a Device
Figure 2-4 Modify Network Parameters
3.
You can enter the IP address of network camera in the address field of the web browser to view
the live video.
Quick Operation Guide of Network Camera
24
Note:
 The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and
password is “12345”.
 For accessing the network camera from different subnets, please set the gateway for the
network camera after you log in.
25
Quick Operation Guide of Network Camera
Chapter 3 Accessing via Web Browsers
System Requirement:
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 /
Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla
Firefox 3.5 and above version and Google Chrome8 and above version
Before you start:
On the IE browser menu bar, navigate to Tools > Internet options > Security > Custom level as
shown in Figure 3-1.
Select LOW in
and click
. Select Enable or
Prompt in ActiveX controls and plug-ins list. The Security Settings interface is shown in Figure 3-2.
Figure 3-1 Navigate to Security Interface
Quick Operation Guide of Network Camera
26
Figure 3-2 Adjust the Security Level
Steps:
1. Open the web browser.
2. In the browser address bar, input the IP address of the network camera, e.g., 192.0.0.64 and
press the Enter key to enter the login interface.
3. Input the user name and password.
4.
Click
.
Quick Operation Guide of Network Camera
27
Figure 3-3 Login Interface
5. Install the plug-in before viewing the live video and managing the camera. Please follow the
installation prompts to install the plug-in.
Note: You may have to close the web browser to finish the installation of the plug-in.
Figure 3-4 Download Plug-in
Figure 3-5 Download Plug-in
28
Quick Operation Guide of Network Camera
Figure 3-6 Install Plug-in
Figure 3-7 Install Plug-in
6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to
login.
Note: For detailed instructions of further configuration, please refer to the user manual of network
camera.
First Choice for Security Professionals
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement