8 Port PoE Ethernet Switch PoE Ethernet Switch User Manual

8 Ports PoE Ethernet Switch

User Manual

VerB 1.1

8 ports PoE Ethernet Switch is an unmanaged Ethernet switch. This product provides 1 Gigabit uplink

Ethernet port and 1 Gigabit uplink fiber port and 8* 100Mbps PoE Ethernet ports, support IEEE802.3af/at power supply standard. The product is widely used in secrity surveillance and network project.

Application

Giga verte bit M r edia

Optic al F iber

1

PoE IP camera

NVR

. . . . . .

8Po rts P

OE E ther net S witc h Cat5

/5e/6

Netw ork C able

PoE Dome camera

PoE PTZ camera

PoE Dome Camera

Feature

Provide 1* 1000Mbps uplink fiber port and 1*1000Mbps Ethernet port, 8* 10/100Mbps downlink Ethernet ports. 1~8 ports of PoE Ethernet switch support IEEE802.3af/at standard, which could provide Max. 30W supply power for infrared camera with large consumption;

Reset button of 8 PoE ports which can easily solve problems of IP camera crash, without plugging network cable, is very convenient for system maintenance;

Under one Key CCTV model, the 1~8 downlink ports can only communicate with uplink ports, the speed of downlink port is limited in 10Mbps and the transmission distance is up to 250m ;

One Key CCTV mode is off by default, but can start while dialing the switch key on the front board to reset the product;

Industrial product, fanless wavy metal shell design for good heat dissipation;

Excellent isolated circuit protection, lighting protection up to 6KV;

Fast installation, easily operation, convenient for wall, din rail and desktop installation.

1 M packet data cache to ensure large capacity data transfer smoothly;

8K MAC address, easy for network system expansion;

Support IEEE802.3X full duplex data control; support port (Auto MDI/MDIX) function ;

Redundant power design, support power hot backup.

Caution

1) Transmission distance is related to the connecting cable. We suggest to use standard Cat5e/6

network cable to get the best transmission result.

2 ) If use optical uplink port, customer needs to purchase additional SFP module.

3 ) The equipment must be connected to anti-thunder grounding ,otherwise the protection level will be

greatly reduced ; please use NO. 20th or above wire to connect grounding terminal to the earth.

Board Diagram

Front Board

8 Port PoE Ethernet Switch

Left Board

SFP optical port

Ethernet

PoE port

Uplink port

Power /Uplink optical port/CCTV indicator LED

Back Board Up Board

Power input

Ground terminal

Power input

Power indicator LED

Reset Button

PoE

port

r

eset button

Description:

1) Front board with PoE Ethernet port, the yellow light on the RJ 45 socket indicate PoE status, the green

light indicate network status; the yellow light and green light on the uplink network RJ 45 socket

indicate network working status; the LED on the left side of SFP optical port indicate power, CCTV and

working status of optical port;

2) The left board and back board have a DC48V~57V power input port respectively; equipped with a

120W power adapter by default, the average PoE output of each port is 15W, output of single port is

max. 30W.

Installation steps

Please check the following items before installation. If any missing, please contact the dealer.

POE Ethernet switch 1 pc

Power adapter 1 pc

MIT hangers 2 pcs

Din rail hanger 1 pc

User manual 1 pc

Please follow the following installation steps

1 ) Please turn off the signal source and the device's power, installation with power on may damage the

device;

2 ) Use 8pcs network cables to connect 8pcs IP cameras with the product's1~8 RJ45 Ethernet ports;

3 ) Use another network cable or (optical fiber) to connect switch’s UPLINK port with NVR or computer;

4 ) Connect switch with power adapter;

5 ) Check if the installation is correct and device is good, make sure all the connection is reliable and power

up the system;

6 ) Make sure every network device has power supply and work normally.

2

3

8 Port PoE Ethernet Switch

Power

Ethernet

Port

Parameter

Ethernet

Exchange

Specification

Item

Power Supply

Voltage range

Consumption

Ethernet Port

Transmission Distance

Transmission Medium

PoE Protocol

PoE Power Supply

PoE Energy

Ethernet Standard

Exchange Capacity

Packet data cache

MAC Address

Power Indicator Light

8 ports PoE Ethernet Switch

Power adapter

DC48V~57V

＜5W

1 ～8 ports: default mode: 10/100Mbps;

CCTV mode:10Mbps;

UPLINK Ethernet port:10/100/1000Mbps; SFP:1000Mbps

Downlink port: default mode: 0～150m; CCTV mode:

0 ~250m

Uplink port: 0～150m

SFP: depends on SFP module performance

Cat5e/6 network cable

IEEE802 .3af/at protocol

End -span

Single port ≤3 0 W

IEEE802 .3 10BASE-T; IEEE802.3u 100BASE-TX;

IEEE802 .3ab 1000BASE-TX;

IEEE802 .3z 1000-SX/LX; IEEE802.3 X

7G

1M

8K

Front board: 1 pcs red Light

Side board: 1 pcs red Light

1 pcs(green), the green light on Indicates CCTV Mode start

1pc SFP port working indicator light: green

Indicator

Status

Reset

Protection

Operation

Environment

CCTV Indicator Light

Optical Port LED indicator

Uplink Ethernet Port

Indicator

Downlink Ethernet Port

Indicator

PoE Reset Button

Reset

Port Lighting Protection

ESD

Working Temperature

Storage Temperature

Humidity

1 pcs network working status: green light on RJ 45 port

1 ～8 ports : green light indicates network status, yellow light indicates PoE status

Total 8 pcs, corresponding to 1～8 ports, PoE Function reset

1 pcs, machine reset

6KV , Per: IEC61000 -4-5

Level 3 , Per: IEC61000 -4-2

-40 ℃ ~75℃

0 ~95%

Mechanical

Dimension (L×W×H)

Material

Color

Weight

159mm×110mm×46.5mm

Aluminum

Black

575g

Products are subject to change without prior notice

8 Port PoE Ethernet Switch

连接接口

连接接口

Shooting

Please find the following solution when the device doesn't work

Please confirm if the installation is correct;

Please confirm if the RJ45 cable order is in accordance with the EIA/TIA568A or 568B industry standards;

The maximum consumption of each PoE port can supply to the PoE device can’t over 30 W, please do not use the PoE device with consumption over 30W;

Please replace a failure device with a properly functioning one to check if the device is broken;

If the problem still exists, please contact the factory.

RJ 45 Making Method

Tools to make RJ45: wire crimper, network tester.

Wire sequence of RJ45 plug should conform with EIA/TIA568A or EIA/TIA568B standard.

1) Strip off the 2cm insulating layer to expose the 4 pairs UTP cable;

2) Seperate the 4 pairs of UTP cable and straighten them;

3) Line up the 8 separated pieces of cables per EIA/TIA 568A or 568B;

4) Cut the cables to leave 1.5cm bare wire and make sure 8 thread ends are flat and neat ;

5) Insert 8 cables into RJ45 plugs, make sure each cable is inserted in each pin;

6)Then use wire crimper to crimp the RJ45;

7) Do the above 5 steps again to make the another end of the twisted pair and make sure consistent cable order between two ends ;

8) Using network tester to test the cable.

Pin color

1 white/green

2 green

3 white/orange

4 blue

5 white/blue

6 orange

Pin color

2 orange

3

6 green

8 brown 8 brown

EIA/TIA 568A

EIA/TIA 568B

Notice

Make sure both ends use EIA/TIA568A connection method when using RJ45 port.

Make sure both ends use EIA/TIA568B connection method when using RJ45 port.

4