advertisement
▼
Scroll to page 2
of 176
BL00004725-202 DIGITAL CAMERA X-Pro2 Owner’s Manual Thank you for your purchase of this product. This manual describes how to use your FUJIFILM X-Pro2 digital camera. Be sure that you have read and understood its contents before using the camera. ■ Product website: http://fujifilm-x.com/x-pro2/ ■ Additional information may be found in online manuals available from: http://fujifilm-dsc.com/manuals/ EN Before You Begin First Steps Basic Photography and Playback Basic Movie Recording and Playback The Q (Quick Menu) Button The Fn (Function) Buttons More on Photography and Playback Menus Connections Technical Notes Troubleshooting Appendix For Your Safety IMPORTANT SAFETY INSTRUCTIONS • Read Instructions: All the safety and operating instructions should be read before the appliance is operated. • Retain Instructions: The safety and operating instructions should be retained for future reference. • Heed Warnings: All warnings on the appliance and in the operating instructions should be adhered to. • Follow Instructions: All operating and use instructions should be followed. Installation Power Sources: This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For video products intended to operate from battery power, or other sources, refer to the operating instructions. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. This video product should never be placed near or over a radiator or heat register. Attachments: Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture: Do not use this video product near water—for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. Power-Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the Grounding or Polarization: This video product is equipped point where they exit from the appliance. with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the Accessories: Do not place this video product on an unstable power outlet only one way. This is a safety feature. If you cart, stand, tripod, bracket, or table. The video product may are unable to insert the plug fully into the outlet, try revers- fall, causing serious injury to a child or adult, and serious ing the plug. If the plug should still fail to fit, contact your damage to the appliance. Use only with a cart, stand, trielectrician to replace your obsolete outlet. Do not defeat pod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the appliance the safety purpose of the polarized plug. should follow the manufacturer’s instructions, and should use Alternate Warnings: This video product is equipped with a mounting accessory recommended by the manufacturer. a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding- An appliance and cart combination type power outlet. This is a safety feature. If you are unable should be moved with care. Quick to insert the plug into the outlet, contact your electrician to stops, excessive force, and uneven replace your obsolete outlet. Do not defeat the safety pur- surfaces may cause the appliance and cart combination to overturn. pose of the grounding type plug. Overloading: Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the video product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the video product on a bed, sofa, rug, or other similar surface. ii Antennas Outdoor Antenna Grounding: If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE Ground Clamp Antenna Lead in Wire Electric Service Equipment Antenna Discharge Unit (NEC SECTION 810-20) Ground Clamps Power Service Grounding Electrode System (NEC ART 250. PART H) Grounding Conductors (NEC SECTION 810-21) Power Lines: An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. Use Cleaning: Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Object and Liquid Entry: Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product. Lightning: For added protection for this video product receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges. For Your Safety Service Be sure to read these notes before use Servicing: Do not attempt to service this video product Safety Notes yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to • Make sure that you use your camera correctly. Read these qualified service personnel. safety notes and your Owner’s Manual carefully before use. Damage Requiring Service: Unplug this video product from • After reading these safety notes, store them in a safe place. the wall outlet and refer servicing to qualified service perAbout the Icons sonnel under the following conditions: The icons shown below are used in this document to indi• When the power-supply cord or plug is damaged cate the severity of the injury or damage that can result if the • If liquid has been spilled, or objects have fallen into the information indicated by the icon is ignored and the product video product. is used incorrectly as a result. • If the video product has been exposed to rain or water. • If the video product has been dropped or the cabinet has This icon indicates that death or seribeen damaged. WARNING ous injury can result if the information If the video product does not operate normally follow the is ignored. operating instructions. Adjust only those controls that are This icon indicates that personal injury covered by the operating instructions as an improper adjustCAUTION or material damage can result if the inment of other controls may result in damage and will often formation is ignored. require extensive work by a qualified technician to restore The icons shown below are used to indicate the nature of the the video product to its normal operation. instructions which are to be observed. When the video product exhibits a distinct change in perforTriangular icons tell you that this information remance — this indicates a need for service. quires attention (“Important”). Replacement Parts: When replacement parts are required, Circular icons with a diagonal bar tell you that the be sure the service technician has used replacement parts action indicated is prohibited (“Prohibited”). specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. Safety Check: Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition. Filled circles with an exclamation mark indicate an action that must be performed (“Required”). WARNING Unplug from power socket Do not use in the bathroom or shower Do not disassemble Do not touch internal parts If a problem arises, turn the camera off, remove the battery, and disconnect and unplug the AC power adapter. Continued use of the camera when it is emitting smoke, is emitting any unusual odor, or is in any other abnormal state can cause a fire or electric shock. Contact your FUJIFILM dealer. Do not allow water or foreign objects to enter the camera. If water or foreign objects get inside the camera, turn the camera off, remove the battery, and disconnect and unplug the AC power adapter. Continued use of the camera can cause a fire or electric shock. Contact your FUJIFILM dealer. Do not use the camera in the bathroom or shower. This can cause a fire or electric shock. Never attempt to change or take apart the camera (never open the case). Failure to observe this precaution can cause fire or electric shock. Should the case break open as the result of a fall or other accident, do not touch the exposed parts. Failure to observe this precaution could result in electric shock or in injury from touching the damaged parts. Remove the battery immediately, taking care to avoid injury or electric shock, and take the product to the point of purchase for consultation. Do not change, heat or unduly twist or pull the connection cord and do not place heavy objects on the connection cord. These actions could damage the cord and cause a fire or electric shock. If the cord is damaged, contact your FUJIFILM dealer. Do not place the camera on an unstable surface. This can cause the camera to fall or tip over and cause injury. Never attempt to take pictures while in motion. Do not use the camera while walking or driving. This can result in you falling down or being involved in a traffic accident. iii For Your Safety WARNING Do not touch any metal parts of the camera during a thunderstorm. This can cause an electric shock due to induced current from the lightning discharge. Do not use the battery except as specified. Load the battery as shown by the indicator. Do not heat, change or take apart the battery. Do not drop or subject the battery to impacts. Do not store the battery with metallic products. Any of these actions can cause the battery to burst or leak and cause fire or injury as a result. Use only batteries or AC power adapters specified for use with this camera. Do not use voltages other than the power supply voltage shown. The use of other power sources can cause a fire. If the battery leaks and fluid gets in contact with your eyes, skin or clothing, flush the affected area with clean water and seek medical attention or call an emergency number right away. Do not use the charger to charge batteries other than those specified here. The supplied charger is for use only with batteries of the type supplied with the camera. Using the charger to charge conventional batteries or other types of rechargeable batteries can cause the battery to leak, overheat or burst. Using a flash too close to a person’s eyes may cause visual impairment. Take particular care when photographing infants and young children. Do not use in the presence of flammable objects, explosive gases, or dust. When carrying the battery, install it in a digital camera or keep it in the hard case. When storing the battery, keep it in the hard case. When discarding, cover the battery terminals with insulation tape. Contact with other metallic objects or batteries could cause the battery to ignite or burst. iv WARNING Keep memory cards, hot shoes, and other small parts out of the reach of small children. Children may swallow small parts; keep out of reach of children. Should a child swallow a small part, seek medical attention or call emergency. Keep out of reach of small children. Among the elements that could cause injury are the strap, which could become entangled about a child’s neck, causing strangulation, and the flash, which could cause visual impairment. Follow the directions of airline and hospital personnel. This product generates radio-frequency emissions that could interfere with navigational or medical equipment. CAUTION Do not use this camera in locations affected by oil fumes, steam, humidity or dust. This can cause a fire or electric shock. Do not leave this camera in places subject to extremely high temperatures. Do not leave the camera in locations such as a sealed vehicle or in direct sunlight. This can cause a fire. Do not place heavy objects on the camera. This can cause the heavy object to tip over or fall and cause injury. Do not move the camera while the AC power adapter is still connected. Do not pull on the connection cord to disconnect the AC power adapter. This can damage the power cord or cables and cause a fire or electric shock. Do not cover or wrap the camera or the AC power adapter in a cloth or blanket. This can cause heat to build up and distort the casing or cause a fire. When you are cleaning the camera or you do not plan to use the camera for an extended period, remove the battery and disconnect and unplug the AC power adapter. Failure to do so can cause a fire or electric shock. When charging ends, unplug the charger from the power socket. Leaving the charger plugged into the power socket can cause a fire. When a memory card is removed, the card could come out of the slot too quickly. Use your finger to hold it and gently release the card. Injury could result to those struck by the ejected card. Request regular internal testing and cleaning for your camera. Build-up of dust in your camera can cause a fire or electric shock. Contact your FUJIFILM dealer to request internal cleaning every two years. Please note that this service is not free of charge. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. For Your Safety ■ Storage The Battery and Power Supply Note: Check the type of battery used in your camera and Performance may be impaired if the battery is left unused for extended periods when fully charged. Run the battery read the appropriate sections. flat before storing it. The following describes the proper use of batteries and how to prolong their life. Incorrect use can shorten battery life or If the camera will not be used for an extended period, remove the battery and store it in a dry place with an ambient cause leakage, overheating, fire, or explosion. temperature of from +15 °C to +25 °C (+59 °F to +77 °F). Do Li-ion Batteries not store in locations exposed to extremes of temperature. Read this section if your camera uses a rechargeable ■ Cautions: Handling the Battery Li-ion battery. • Do not transport or store with metal objects such as neckThe battery is not charged at shipment. Charge the battery laces or hairpins. before use. Keep the battery in its case when not in use. • Do not expose to flame or heat. • Do not disassemble or modify. ■ Notes on the Battery The battery gradually loses its charge when not in use. • Use with designated chargers only. • Dispose of used batteries promptly. Charge the battery one or two days before use. • Do not drop or subject to strong physical shocks. Battery life can be extended by turning the camera off when • Do not expose to water. not in use. • Keep the terminals clean. Battery capacity decreases at low temperatures; a depleted • The battery and camera body may become warm to the touch after extended use. This is normal. battery may not function when cold. Keep a fully charged spare battery in a warm place and exchange as necessary, ■ Disposal or keep the battery in your pocket or other warm place and Dispose of used batteries in accord with local regulations. insert it in the camera only when shooting. Do not place the battery in direct contact with hand warmers or other AC Power Adapters (Available Separately) Use only FUJIFILM AC power adapters designated for use heating devices. with this camera. Other adapters could damage the camera. ■ Charging the Battery • The AC power adapter is for indoor use only. Charge the battery in the supplied battery charger. Charging • Be sure the DC plug is securely connected to the camera. times will increase at ambient temperatures below +10 °C • Turn the camera off before disconnecting the adapter. (+50 °F) or above +35 °C (+95 °F). Do not attempt to charge Disconnect the adapter by the plug, not the cable. the battery at temperatures above 40 °C (+104 °F); at tem• Do not use with other devices. peratures below 0 °C (+32 °F), the battery will not charge. • Do not disassemble. Do not attempt to recharge a fully charged battery. The bat- • Do not expose to high heat and humidity. tery does not however need to be fully discharged before • Do not subject to strong physical shocks. charging. • The adapter may hum or become hot to the touch during use. This is normal. The battery may be warm to the touch immediately after • If the adapter causes radio interference, reorient or relocate charging or use. This is normal. the receiving antenna. ■ Battery Life At normal temperatures, the battery can be recharged about 300 times. A noticeable decrease in the length of time the battery will hold a charge indicates that it has reached the end of its service life and should be replaced. Using the Camera • Do not aim the camera at extremely bright light sources, such as the sun in a cloudless sky. Failure to observe this precaution could damage the camera image sensor. • Strong sunlight focused through the viewfinder may damage the panel of electronic viewfinder (EVF). Do not aim the electronic viewfinder at the sun. Take Test Shots Before taking photographs on important occasions (such as at weddings or before taking the camera on a trip), take a test shot and view the results to ensure that the camera is functioning normally. FUJIFILM Corporation can not accept liability for damages or lost profits incurred as a result of product malfunction. Notes on Copyright Unless intended solely for personal use, images recorded using your digital camera system cannot be used in ways that infringe copyright laws without the consent of the owner. Note that some restrictions apply to the photographing of stage performances, entertainments, and exhibits, even when intended purely for personal use. Users are also asked to note that the transfer of memory cards containing images or data protected under copyright laws is only permissible within the restrictions imposed by those copyright laws. Handling To ensure that images are recorded correctly, do not subject the camera to impact or physical shocks while images are being recorded. v For Your Safety Liquid Crystal In the event that the display is damaged, care should be taken to avoid contact with liquid crystal. Take the urgent action indicated should any of the following situations arise: • If liquid crystal comes in contact with your skin, clean the area with a cloth and then wash thoroughly with soap and running water. • If liquid crystal enters your eyes, flush the affected eye with clean water for at least 15 minutes and then seek medical assistance. • If liquid crystal is swallowed, rinse your mouth thoroughly with water. Drink large quantities of water and induce vomiting, then seek medical assistance. Electrical Interference NOTICES This camera may interfere with hospital or aviation equipTo prevent fire or shock hazard, do not expose the unit ment. Consult with hospital or airline staff before using the to rain or moisture. camera in a hospital or on an aircraft. Please read the “Safety Notes” and make sure you unColor Television Systems derstand them before using the camera. NTSC (National Television System Committee) is a color television telecasting specification adopted mainly in the U.S.A., Perchlorate Material—special handling may apply. See Canada, and Japan. PAL (Phase Alternation by Line) is a color http://www.dtsc.ca.gov/hazardouswaste/perchlorate. television system adopted mainly in European countries and China. Exif Print (Exif Version 2.3) Exif Print is a newly revised digital camera file format in Although the display is manufactured using extremely high- which information stored with photographs is used for optiprecision technology, it may contain pixels that are always lit mal color reproduction during printing. or that do not light. This is not a malfunction, and images IMPORTANT NOTICE: Read Before Using the Software recorded with the product are unaffected. Direct or indirect export, in whole or in part, of licensed software without the permission of the applicable governing Trademark Information Digital Split Image is a trademark or registered trademark bodies is prohibited. of FUJIFILM Corporation. xD-Picture Card and E are trademarks of FUJIFILM Corporation. The typefaces included herein are solely developed by DynaComware Taiwan Inc. Macintosh, QuickTime, and Mac OS are trademarks of Apple Inc. in the U.S.A. and other countries. The Windows logo is a trademark of the Microsoft group of companies. Wi-Fi® and Wi-Fi Protected Setup® are registered trademarks of the Wi-Fi Alliance. Adobe and Adobe Reader are either trademarks or registered trademarks of Adobe Systems Incorporated in the U.S.A. and/or other countries. The SDHC and SDXC logos are trademarks of SD-3C, LLC. The HDMI logo is a trademark. All other trade names mentioned in this manual are the trademarks or registered trademarks of their respective owners. vi For Your Safety For Customers in the U. S. A. Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. X-Pro2 has been tested and found to comply with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted FCC Statement: This device complies with Part 15 of the FCC by the FCC with the device transmitting at its highest certiDisposal of Electrical and Electronic Equipment in Private Households Rules. Operation is subject to the following two conditions: fied power level in all tested frequency bands. In the European Union, Norway, Iceland and (1) This device may not cause harmful interference, and Liechtenstein: This symbol on the product, or in (2) this device must accept any interference received, includ- Notes on the Grant: To comply with Part 15 of the FCC Rules, this product must be used with a Fujifilm-specified ferrite- the manual and in the warranty, and/or on its ing interference that may cause undesired operation. packaging indicates that this product shall not core A/V cable, USB cable, and DC supply cord. CAUTION: This equipment has been tested and found to combe treated as household waste. Instead it should ply with the limits for a Class B digital device, pursuant to be taken to an applicable collection point for the A lithium ion battery that is recyclable Part 15 of the FCC Rules. These limits are designed to prorecycling of electrical and electronic equipment. powers the product you have purchased. vide reasonable protection against harmful interference in a Please call 1-800-8-BATTERY for informaBy ensuring this product is disposed of correctly, you will residential installation. This equipment generates, uses, and tion on how to recycle this battery. help prevent potential negative consequences to the encan radiate radio frequency energy and, if not installed and vironment and human health, which could otherwise be used in accordance with the instructions, may cause harmful For Customers in Canada caused by inappropriate waste handling of this product. interference to radio communications. However, there is no CAN ICES-3 (B)/NMB-3(B) This symbol on the batteries or accumulators inguarantee that interference will not occur in a particular inCAUTION: This Class B digital apparatus complies with Cana- dicates that those batteries shall not be treated stallation. If this equipment does cause harmful interference dian ICES-003. as household waste. to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged Industry Canada statement: This device complies with Industo try to correct the interference by one or more of the fol- try Canada’s licence-exempt RSSs. Operation is subject to If your equipment contains easy removable batteries or the following two conditions: (1) This device may not cause accumulators please dispose these separately according to lowing measures: interference; and (2) This device must accept any interfer- your local requirements. • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. ence, including interference that may cause undesired op- The recycling of materials will help to conserve natural resourc• Connect the equipment into an outlet on a circuit different eration of the device. es. For more detailed information about recycling this product, from that to which the receiver is connected. This device and its antenna(s) must not be co-located or op- please contact your local city office, your household waste • Consult the dealer or an experienced radio/TV technician erating in conjunction with any other antenna or transmit- disposal service or the shop where you purchased the product. for help. ter, except tested built-in radios. The County Code Selection In Countries Outside the European Union, Norway, Iceland and FCC Caution: Any changes or modifications not expressly ap- feature is disabled for products marketed in the US/ Canada. Liechtenstein: If you wish to discard this product, including proved by the party responsible for compliance could void Radiation Exposure Statement: The available scientific the batteries or accumulators, please contact your local authe user’s authority to operate this equipment. evidence does not show that any health problems are as- thorities and ask for the correct way of disposal. This transmitter must not be co-located or operating in con- sociated with using low power wireless devices. There is no In Japan: This symbol on the batteries indicates proof, however, that these low power wireless devices are that they are to be disposed of separately. junction with any other antenna or transmitter. absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health Contains IC : 7736B-02000002 Contains FCC ID : W2Z-02000002 vii For Your Safety Be sure to read these notes before use Safety Notes Thank you for your purchase of this product. For repair, inspection, and internal testing, contact your FUJIFILM dealer. • Make sure that you use the lens correctly. Read these safety notes and the camera Owner’s Manual carefully before use. • After reading these safety notes, store them in a safe place. About the Icons The icons shown below are used in this document to indicate the severity of the injury or damage that can result if the information indicated by the icon is ignored and the product is used incorrectly as a result. This icon indicates that death or serious injury can result if the information is ignored. This icon indicates that personal injury or material damage can result if CAUTION the information is ignored. WARNING The icons shown below are used to indicate the nature of the instructions which are to be observed. Triangular icons tell you that this information requires attention (“Important”). Circular icons with a diagonal bar tell you that the action indicated is prohibited (“Prohibited”). Filled circles with an exclamation mark indicate an action that must be performed (“Required”). WARNING Do not use in the bathroom or shower Do not disassemble Do not touch internal parts viii Do not immerse in or expose to water. Failure to observe this precaution can cause a fire or electric shock. Do not disassemble (do not open the case). Failure to observe this precaution can cause fire, electric shock, or injury due to product malfunction. Should the case break open as the result of a fall or other accident, do not touch the exposed parts. Failure to observe this precaution could result in electric shock or in injury from touching the damaged parts. Remove the camera battery immediately, taking care to avoid injury or electric shock, and take the product to the point of purchase for consultation. WARNING Do not place on unstable surfaces. The product may fall, causing injury. Do not view the sun through the lens or camera viewfinders. Failure to observe this precaution can cause permanent visual impairment. CAUTION Do not use or store in locations that are exposed to steam, or smoke or are very humid or extremely dusty. Failure to observe this precaution can cause fire or electric shock. Do not leave in direct sunlight or in locations subject to very high temperatures, such as in a closed vehicle on a sunny day. Failure to observe this precaution can cause fire. Keep out of the reach of small children. This product could cause injury in the hands of a child. Do not handle with wet hands. Failure to observe this precaution can cause electric shock. Keep the sun out of the frame when shooting backlit subjects. Sunlight focused into the camera when the sun is in or close to the frame can cause fire or burns. When the product is not in use, replace the lens caps and store out of direct sunlight. Sunlight focused by the lens can cause fire or burns. Do not carry the camera or lens while they are attached to a tripod. The product can fall or strike other objects, causing injury. For Your Safety European Union regulatory notice This product complies with the following EU Directives: • RoHS Directive 2011/65/EU • R & TTE Directive 1999/5/EC Wireless Network Devices: Cautions • This device operates on the same frequency as commercial, educational, and medical devices and wireless transmitters. It also operates on the same frequency as licensed transmitters and special unlicensed low-voltage transmitters used in RFID tracking systems for assembly lines and in other similar applications. Compliance with these directives implies conformity to applicable harmonized European • To prevent interference with the above devices, observe the following precautions. Confirm that standards (European Norms) which are listed on the EU Declaration of Conformity issued by the RFID transmitter is not in operation before using this device. Should you observe that FUJIFILM Corporation for this product or product family. the device causes interference in licensed transmitters used for RFID tracking, immediThis compliance is indicated by the following conformity marking placed on the product: ately stop using the affected frequency or move the device to another location. If you notice that this device causes interference in low-voltage RFID tracing systems, contact a FUJIFILM representative. This marking is valid for non-Telecom products and EU harmonized Telecom products (e.g. Bluetooth). Regarding the Declaration of Conformity, visit http://www.fujifilm.com/products/digital_ cameras/x/fujifilm_x_pro2/pdf/index/fujifilm_x_pro2_cod.pdf. 2.4DS/OF4 This sticker indicates that this device operates in the 2.4 GHz band using DSSS and OFDM modulation and may cause interference at distances of up to 40 m. IMPORTANT: Read the following notices before using the camera’s built-in wireless transmitter. Q This product, which contains encryption function developed in the United States, is controlled by the United States Export Administration Regulations and may not be exported or re-exported to any country to which the United States embargoes goods. • Use only as part of a wireless network. FUJIFILM does not accept liability for damages resulting from unauthorized use. Do not use in applications requiring a high degree of reliability, for example in medical devices or other systems that may directly or indirectly impact human life. When using the device in computer and other systems that demand a greater degree of reliability than wireless networks, be sure to take all necessary precautions to ensure safety and prevent malfunction. • Use only in the country in which the device was purchased. This device conforms to regulations governing wireless network devices in the country in which it was purchased. Observe all location regulations when using the device. FUJIFILM does not accept liability for problems arising from use in other jurisdictions. • Wireless data (images) may be intercepted by third parties. The security of data transmitted over wireless networks is not guaranteed. • Do not use the device in locations subject to magnetic fields, static electricity, or radio interference. Do not use the transmitter in the vicinity of microwave ovens or in other locations subject to magnetic fields, static electricity, or radio interference that may prevent reception of wireless signals. Mutual interference may occur when the transmitter is used in the vicinity of other wireless devices operating in the 2.4 GHz band. • The wireless transmitter operates in the 2.4 GHz band using DSSS and OFDM modulation. ix About This Manual Before using the camera, read this manual and the warnings in “For Your Safety” (P ii). For information on specific topics, consult the sources below. Table of Contents ................................................ P xiii The “Table of Contents” gives an overview of the entire manual. The principal camera operations are listed here. Troubleshooting ................................................P ................................................ P 137 Having a specific problem with the camera? Find the answer here. Warning Messages and Displays .........................P ......................... P 142 Find out what’s behind that flashing icon or error message in the display. Restrictions on Camera Settings ..........................P .......................... P 153 See page 153 for restrictions on the options available in each shooting mode. Memory Cards Pictures are stored on optional SD, SDHC, and SDXC memory cards (P 24), referred to in this manual as “memory cards.” x Product Care Camera body: For continued enjoyment of your camera, use a soft, dry cloth to clean the camera body after each use. Do not use alcohol, thinner, or other volatile chemicals, which could discolor or deform the leather on the camera body. Any liquid on the camera should be removed immediately with a soft, dry cloth. Use a blower to remove dust from the monitor, taking care to avoid scratches, and then gently wipe with a soft, dry cloth. Any remaining stains can be removed by wiping gently with a piece of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning fluid has been applied. To prevent dust entering the camera, replace the body cap when no lens is in place. Image sensor: Dust can be removed from the image sensor using the D USER SETTING > SENSOR CLEANING (P 108) option in the camera menus. Interchangeable lenses: Use a blower to remove dust, then gently wipe with a soft, dry cloth. Any remaining stains can be removed by wiping gently with a piece of FUJIFILM lens-cleaning paper to which a small amount of lens-cleaning fluid has been applied. Replace the front and rear caps when the lens is not in use. xi Product Features Frequently-used options can be added to the Q menu or a custom “my” menu or assigned to an Fn (function) button for direct access. Customize camera controls to suit your style or situation. The Q Menu (P (P 47) The Q menu is displayed by pressing the Q button. SELECT CUSTOM SETTING The Function Buttons (P (P 50) Use the function buttons for direct access to selected features. BASE 32 27 23 SET 18 Use the Q menu to view or change the options selected for frequently-used menu items. “My Menu” (P (P 100) Add frequently-used options to this custom menu, which can be viewed by pressing MENU/OK and selecting the E (“MY MENU”) tab. MY MENU SELF-TIMER INTERVAL TIMER SHOOTING FILM SIMULATION BKT PHOTOMETRY SHUTTER TYPE IS MODE FACE/EYE DETECTION SETTING ISO AUTO SETTING EXIT R The E tab is only available if options have been assigned to “MY MENU”. xii Press the button for direct access to the assigned function. The illustration shows the Fn2 button being used to display the bright frame simulation. Table of Contents For Your Safety .....................................................................................ii IMPORTANT SAFETY INSTRUCTIONS.........................................ii Safety Notes .......................................................................................iii NOTICES ...............................................................................................vi Safety Notes .....................................................................................viii About This Manual .............................................................................x Product Care ........................................................................................xi Product Features...............................................................................xii The Q Menu .......................................................................................xii “My Menu” .........................................................................................xii The Function Buttons ....................................................................xii Before You Begin Symbols and Conventions..............................................................1 Supplied Accessories ........................................................................1 Parts of the Camera ...........................................................................2 The Selector ........................................................................................4 The Focus Stick (Focus Lever).......................................................4 The Shutter-Speed/ISO Dial ..........................................................4 The Front Command Dial...............................................................5 The Rear Command Dial ................................................................6 The Indicator Lamp ..........................................................................7 Camera Displays ................................................................................8 Shooting: Optical Viewfinder ....................................................8 Shooting: Electronic Viewfinder/LCD Monitor ................ 10 Playback.......................................................................................... 12 Lenses ................................................................................................... 13 Parts of the Lens ............................................................................. 13 Removing the Caps ....................................................................... 13 Attaching the Hood ...................................................................... 13 Lenses with Aperture Rings ....................................................... 14 Lenses with No Aperture Rings ................................................ 14 Lenses with O.I.S. Switches......................................................... 15 Manual Focus Lenses.................................................................... 15 First Steps Attaching the Strap ........................................................................ 16 Attaching a Lens .............................................................................. 18 Charging the Battery ..................................................................... 19 Inserting the Battery...................................................................... 20 Inserting Memory Cards............................................................... 22 Using Two Cards ............................................................................. 23 Compatible Memory Cards ..................................................... 24 Turning the Camera on and Off ................................................ 25 Basic Setup ......................................................................................... 26 Changing Basic Settings ............................................................. 27 Display Settings ............................................................................... 28 Choosing a Display........................................................................ 28 The Viewfinder Selector .............................................................. 29 Bright Frame Simulation ............................................................. 30 The Viewfinder Display ................................................................ 31 Focusing the Viewfinder ............................................................. 31 Adjusting Display Brightness .................................................... 31 The DISP/BACK Button ....................................................................... 32 Shooting: Optical Viewfinder ................................................. 32 Shooting: Electronic Viewfinder............................................ 32 LCD Monitor: Shooting ............................................................. 32 Customizing the Standard Display ...................................... 33 Viewfinder/LCD Monitor: Playback ...................................... 34 xiii Table of Contents Basic Photography and Playback More on Photography and Playback Program AE (P) .................................................................................. 35 Shutter-Priority AE (S) ................................................................... 36 Aperture-Priority AE (A) ............................................................... 37 Manual Exposure (M) ..................................................................... 38 Viewing Pictures .............................................................................. 39 Viewing Pictures Full Frame....................................................... 39 Viewing Photo Information ....................................................... 40 Playback Zoom ............................................................................... 41 Multi-Frame Playback................................................................... 42 Deleting Pictures ............................................................................. 43 Drive Mode ......................................................................................... 52 R Burst Mode (CONTINUOUS) ................................................. 53 Bracketing ......................................................................................... 54 Y Advanced Filters...................................................................... 55 j Multiple Exposures.................................................................. 56 Exposure Compensation .............................................................. 57 C (Custom) ..................................................................................... 57 Sensitivity ........................................................................................... 58 Metering .............................................................................................. 59 Film Simulation ................................................................................ 60 White Balance ................................................................................... 61 Focus Mode ........................................................................................ 63 The Focus Indicator .................................................................... 64 MF Assist ......................................................................................... 65 Autofocus Options (AF Mode) .................................................. 66 Focus-Point Selection................................................................... 67 The Focus Point Display .............................................................. 68 Single Point AF ............................................................................. 68 Zone AF ........................................................................................... 69 Tracking (Focus Mode C Only) ................................................ 70 Long Time-Exposures (T/B) ......................................................... 71 Time (T) .............................................................................................. 71 Bulb (B) ............................................................................................... 71 Using a Remote Release .............................................................. 72 Basic Movie Recording and Playback Recording Movies............................................................................ 44 Using an External Microphone ................................................. 45 Viewing Movies ................................................................................ 46 The Q (Quick Menu) Button Using the Q Button ......................................................................... 47 The Quick Menu Display ............................................................. 47 Viewing and Changing Settings .............................................. 48 Editing the Quick Menu .............................................................. 49 The Fn (Function) Buttons Using the Function Buttons ........................................................ 50 Assigning Roles to the Function Buttons ............................. 51 xiv Table of Contents The Self-Timer ................................................................................... 73 Interval Timer Photography ....................................................... 74 Focusing and Taking Pictures .................................................... 75 Focus/Exposure Lock ..................................................................... 76 Flash Photography.......................................................................... 78 Recording Pictures in RAW Format ......................................... 80 Creating JPEG Copies of RAW Pictures .................................. 81 Saving Settings................................................................................. 82 Using a Mount Adapter ................................................................ 83 Bright Frame Brightness.............................................................. 83 Lens Registration............................................................................ 83 Choosing a Focal Length ......................................................... 83 Distortion Correction ................................................................ 83 Color Shading Correction ........................................................ 84 Peripheral Illumination Correction ...................................... 84 PhotoBook Assist............................................................................. 85 Creating a PhotoBook .................................................................. 85 Viewing Photobooks .................................................................... 86 Editing and Deleting Photobooks........................................... 86 Menus Using the Menus: Shooting Mode ........................................... 87 Using the Shooting Menu .......................................................... 87 H IMAGE QUALITY SETTING ...................................................... 88 IMAGE SIZE .................................................................................... 88 IMAGE QUALITY ........................................................................... 88 RAW RECORDING ........................................................................ 88 FILM SIMULATION ....................................................................... 89 GRAIN EFFECT .............................................................................. 89 DYNAMIC RANGE ........................................................................ 89 WHITE BALANCE .......................................................................... 89 HIGHLIGHT TONE ........................................................................ 89 SHADOW TONE ............................................................................ 89 COLOR ............................................................................................. 89 SHARPNESS ................................................................................... 89 NOISE REDUCTION ..................................................................... 89 LONG EXPOSURE NR .................................................................. 90 LENS MODULATION OPTIMIZER............................................ 90 COLOR SPACE................................................................................ 90 PIXEL MAPPING............................................................................ 90 SELECT CUSTOM SETTING ....................................................... 90 EDIT/SAVE CUSTOM SETTING................................................. 90 xv Table of Contents G AF/MF SETTING ......................................................................... 91 FOCUS AREA ................................................................................. 91 AF MODE ........................................................................................ 91 NUMBER OF THE FOCUS POINTS .......................................... 91 PRE-AF ............................................................................................. 91 AF ILLUMINATOR ......................................................................... 91 FACE/EYE DETECTION SETTING ............................................. 92 AF+MF ............................................................................................. 93 MF ASSIST ...................................................................................... 93 FOCUS CHECK .............................................................................. 93 INTERLOCK SPOT AE & FOCUS AREA ................................... 93 INSTANT AF SETTING ................................................................. 93 DEPTH-OF-FIELD SCALE ........................................................... 94 RELEASE/FOCUS PRIORITY ...................................................... 94 CORRECTED AF FRAME ............................................................. 94 A SHOOTING SETTING ................................................................ 95 SELF-TIMER .................................................................................... 95 INTERVAL TIMER SHOOTING ................................................... 95 FILM SIMULATION BKT .............................................................. 95 PHOTOMETRY ............................................................................... 95 SHUTTER TYPE.............................................................................. 96 IS MODE .......................................................................................... 96 ISO AUTO SETTING ..................................................................... 97 MOUNT ADAPTOR SETTING.................................................... 97 WIRELESS COMMUNICATION ................................................. 97 xvi F FLASH SETTING ......................................................................... 98 FLASH MODE ................................................................................ 98 FLASH COMPENSATION............................................................ 98 RED EYE REMOVAL...................................................................... 98 B MOVIE SETTING ......................................................................... 99 MOVIE MODE ................................................................................ 99 MIC LEVEL ADJUSTMENT ......................................................... 99 MIC/REMOTE RELEASE .............................................................. 99 E MY MENU ...................................................................................100 Using the Menus: Playback Mode..........................................101 Using the Playback Menu .........................................................101 C PLAY BACK MENU ...................................................................102 SWITCH SLOT ..............................................................................102 RAW CONVERSION....................................................................102 ERASE .............................................................................................102 CROP ..............................................................................................102 RESIZE ............................................................................................103 PROTECT .......................................................................................103 IMAGE ROTATE............................................................................103 RED EYE REMOVAL....................................................................104 COPY ..............................................................................................104 WIRELESS COMMUNICATION ...............................................104 SLIDE SHOW ................................................................................105 PHOTOBOOK ASSIST ................................................................105 PC AUTO SAVE ............................................................................105 PRINT ORDER (DPOF)...............................................................105 instax PRINTER PRINT ..............................................................105 DISP ASPECT ...............................................................................105 Table of Contents The Setup Menu .............................................................................106 Using the Setup Menu ...............................................................106 D SET UP Menu Options ...........................................................107 D USER SETTING .......................................................................107 FORMAT ........................................................................................107 DATE/TIME ...................................................................................107 TIME DIFFERENCE .....................................................................108 a .....................................................................................108 MY MENU SETTING...................................................................108 SENSOR CLEANING...................................................................108 RESET .............................................................................................108 D SOUND SETTING ..................................................................109 AF BEEP VOL. ...............................................................................109 SELF-TIMER BEEP VOL. .............................................................109 OPERATION VOL. .......................................................................109 SHUTTER VOLUME ....................................................................109 SHUTTER SOUND ......................................................................109 PLAYBACK VOLUME..................................................................109 D SCREEN SETTING ..................................................................110 EVF BRIGHTNESS .......................................................................110 EVF COLOR ...................................................................................110 LCD BRIGHTNESS.......................................................................110 LCD COLOR ..................................................................................110 IMAGE DISP. .................................................................................110 EVF AUTOROTATE DISPLAYS .................................................110 PREVIEW EXP./WB IN MANUAL MODE...............................110 PREVIEW PIC. EFFECT...............................................................111 FRAMING GUIDELINE...............................................................111 AUTOROTATE PB ........................................................................111 FOCUS SCALE UNITS ................................................................111 DISP. CUSTOM SETTING ..........................................................111 D BUTTON/DIAL SETTING .....................................................112 FOCUS LEVER SETTING ...........................................................112 EDIT/SAVE QUICK MENU ........................................................112 FUNCTION (Fn) SETTING ........................................................112 COMMAND DIAL SETTING .....................................................112 ISO DIAL SETTING (H) ..............................................................112 SHOOT WITHOUT LENS...........................................................112 FOCUS RING ................................................................................112 AE-L/AF-L BUTTON SETTING ................................................113 AE/AF-LOCK MODE...................................................................113 AF-LOCK MODE..........................................................................113 APERTURE SETTING..................................................................113 D POWER MANAGEMENT .....................................................114 AUTO POWER OFF ....................................................................114 POWER MANAGEMENT...........................................................114 D SAVE DATA SETTING ...........................................................115 FRAME NO. ...................................................................................115 SAVE ORG IMAGE ......................................................................115 EDIT FILE NAME .........................................................................115 CARD SLOT SETTING (STILL IMAGE) ...................................116 SWITCH SLOT (SEQUENTIAL) ................................................116 D CONNECTION SETTING......................................................117 WIRELESS SETTINGS.................................................................117 PC AUTO SAVE SETTING .........................................................117 GEOTAGGING SET-UP ..............................................................117 instax PRINTER CONNECTION SETTING ...........................117 “My Menu” ........................................................................................118 Editing “My Menu” .......................................................................118 Factory Defaults .............................................................................119 xvii Table of Contents Connections Troubleshooting Wireless Transfer ............................................................................122 Wireless Connections: Smartphones ...................................122 Wireless Connections: Computers ........................................122 Viewing Pictures on a Computer ............................................123 Windows ..........................................................................................123 Macintosh .......................................................................................123 Connecting the Camera ............................................................124 Creating a DPOF Print Order ....................................................126 WITH DATE s/ WITHOUT DATE ..........................................126 RESET ALL.....................................................................................127 instax SHARE Printers ..................................................................128 Establishing a Connection........................................................128 Printing Pictures ...........................................................................129 Viewing Pictures on TV ...............................................................130 Problems and Solutions .............................................................137 Warning Messages and Displays ............................................142 Technical Notes Optional Accessories....................................................................131 Accessories from FUJIFILM .......................................................131 Connecting the Camera to Other Devices .........................134 Caring for the Camera .................................................................135 Use and Storage Precautions ..................................................135 Traveling ..........................................................................................135 Cleaning the Image Sensor .......................................................136 xviii Appendix Memory Card Capacity ...............................................................145 Links.....................................................................................................146 FUJIFILM X-Pro2 Product Information .................................146 Firmware Updates .......................................................................146 Free FUJIFILM Apps .....................................................................146 Specifications ..................................................................................147 Restrictions on Camera Settings ............................................153 Before You Begin Symbols and Conventions Menus and other text in the displays are shown in bold. In the illustrations in this manual, displays may be simplified for explanatory purposes. Supplied Accessories Before You Begin The following symbols are used in this manual: Q This information should be read before use to ensure correct operation. R Additional information that may be helpful when using the camera. POther pages in this manual on which related information may be found. The following items are included with the camera: NP-W126 rechargeable battery Clip attaching tool BC-W126 battery charger Metal strap clips (× 2) Body cap • Protective covers (× 2) • Shoulder strap • Hot shoe cover (comes attached to hot shoe) • Sync terminal cap (comes attached to camera) • Owner’s Manual (this manual) 1 Parts of the Camera For more information, refer to the page listed to the right of each item. 2 Parts of the Camera i Memory card slot cover.....................................22 j Cable channel cover for DC coupler .................131 k Battery-chamber cover latch ............................20 l Battery-chamber cover .....................................20 m Speaker.............................................................46 n Tripod mount o Indicator lamp ....................................................7 p LCD monitor .......................................... 10, 28, 32 q DISP (display)/BACK button ............................32 Function button role selection (press and hold) .........................................................................51 r b (delete) button ........................................ 6, 43 s a (playback) button ......................................39 t Body cap ...........................................................18 u Memory card slot 2 ...........................................22 v Memory card slot 1 ...........................................22 w Battery latch .....................................................20 x Battery chamber ...............................................20 Before You Begin A Movie-record button.........................................44 S Front command dial ...........................................5 Function button (Fn1) ......................................50 T ON/OFF switch .................................................25 B Shutter button ..................................................75 U Hot shoe cover ..................................................78 C Exposure compensation dial .............................57 V Micro HDMI connector ....................................130 D Shutter speed dial/Sensitivity dial W Micro USB connector.......................................124 ....................................................4, 35, 36, 37, 38 X Microphone/remote release connector ....... 45, 72 E Dial lock release ...................................... 4, 36 ,38 Y Eye sensor .........................................................28 F AF-assist illuminator.........................................91 Z VIEW MODE button .........................................28 Self-timer lamp ................................................73 a Metering button ...............................................59 Function button (Fn3) ......................................50 G Hot shoe ..................................................... 78, 79 H Microphone ......................................................45 b AE-L (exposure lock) button ..................... 76, 113 I Viewfinder window ................................ 8, 28, 32 c Focus stick (focus lever) .......................... 4, 67, 68 J Diopter adjustment control...............................31 d Rear command dial.............................................6 K Strap eyelet ......................................................16 e AF-L (focus lock) button ..................... 63, 76, 113 L Sync terminal....................................................79 f Q (quick menu) button * ....................................47 Quick menu edit/custom settings button M Connector cover ...........................45, 72, 124, 130 (press and hold) * ..............................................49 N Focus mode selector .........................................63 RAW conversion button (playback mode) .........81 O Lens signal contacts ..........................................13 P Lens release button ..........................................18 g Selector ........................................................ 4, 26 Function buttons ..............................................50 Q Viewfinder selector ..................................... 29, 30 R Bright frame simulation display button ............30 h MENU/OK button ............................. 87, 101, 106 Function button (Fn2) ......................................50 X (control lock) button (press and hold) ........11 * In shooting mode, press and release to display quick menu or press and hold to display quick menu edit options. When quick menu is displayed, press and hold to edit custom settings. Control Lock To prevent accidental operation of the selector and Q button during shooting, press MENU/OK until X is displayed. The controls can be unlocked by pressing MENU/OK until X is no longer displayed. 3 Parts of the Camera The Selector Press the selector up (q), right (e), down (r), or left (w) to highlight items. The up, left, right, and down buttons also double as the DRIVE (P 52), Fn4 (film simulation; P 60), Fn5 (white balance; P 61), and Fn6 (AF mode; P 66) buttons, respectively (P 50). The Shutter-Speed/ISO Dial Choose a shutter speed and ISO sensitivity. Rotate the dial to choose a shutter speed (P 35, 36, 37, 38). R If the dial is in the A position, press the lock release while rotating the dial. The Focus Stick (Focus Lever) Tilt or press the focus stick to select the focus area (P 67). 4 Lift and rotate the dial to choose ISO sensitivity (P 58). Parts of the Camera The Front Command Dial The front command dial is used as described below. Before You Begin Rotate the dial to choose the desired combination of shutter speed and aperture (program shift; P 35), fine-tune shutter speed (P 36, 38), adjust exposure compensation when C is selected with the exposure compensation dial (P 57), or view other pictures in playback mode (P 39). Press the center of the dial to switch back and forth between shutter speed and exposure compensation when C is selected with the exposure compensation dial (P 35, 36, 38, 57). 5 Parts of the Camera The Rear Command Dial The rear command dial is used as described below. Rotate the dial to choose the desired combination of shutter speed and aperture (program shift; P 35), adjust aperture (P 14, 37, 38), adjust settings in the quick menu (P 48), choose the size of the focus frame (P 68, 69), or zoom in or out in full-frame or thumbnail playback (P 41, 42). Press the center of the dial to zoom in on the selected focus area (P64) or in playback mode to zoom in on the active focus point (P 40). In manual focus mode, you can choose a focus display by pressing and holding the center of the dial (P 65). Formatting Memory Cards To format memory cards, press the center of the command dial while pressing and holding the b button. The FORMAT menu will be displayed; select a slot and format the card as described on page 107. 6 Parts of the Camera The Indicator Lamp When the viewfinder is not in use (P 28), the indicator lamp shows camera status. Indicator lamp Before You Begin Indicator lamp Camera status Glows green Focus locked. Blinks green Focus or exposure warning. Pictures can be taken. Blinks green and orange Recording pictures. Additional pictures can be taken. Recording pictures. No additional pictures can be taken at this Glows orange time. Blinks orange Flash charging; flash will not fire when picture is taken. Blinks red Lens or memory error. R Warnings may also appear in the display (P 142). 7 Parts of the Camera Camera Displays The following types of indicator may be displayed during shooting and playback. In the description that follows, all available indicators are shown for illustrative purposes; the indicators actually displayed vary with camera settings. Note that the LCD monitor and electronic viewfinder have different aspect ratios. ■ Shooting: Optical Viewfinder 3 2 1 0 -1 -2 -3 8 Parts of the Camera N Virtual horizon ..................................................34 O Distance indicator .............................................63 P Sensitivity.........................................................58 Q Exposure compensation ....................................57 R Aperture ............................................... 35, 37, 38 S Shutter speed ....................................... 35, 36, 38 T AE lock indicator ...............................................76 U Metering...........................................................59 V Shooting mode ................................35, 36, 37, 38 W Focus indicator..................................................64 X Manual focus indicator .....................................64 Y Focus mode ......................................................63 Z Histogram.........................................................34 a Dynamic range .................................................89 b Film simulation.................................................60 c White balance...................................................61 d Exposure indicator ...................................... 38, 57 e AF+MF indicator ..............................................93 f Shutter type......................................................96 g Continuous mode ....................................... 52, 53 h Self-timer indicator ..........................................73 i Microphone/remote release ................. 45, 72, 99 j Flash mode/Flash compensation ................ 78, 98 Before You Begin A IS mode ............................................................96 B Control lock.........................................................3 C Depth-of-field preview .....................................37 D Location data download status .......................117 E Movie mode................................................ 44, 99 F Time remaining ................................................44 G Card slot options ....................................... 23, 116 H Number of available frames * .........................145 I Image quality and size ......................................88 J Battery level .....................................................25 K Bright frame .....................................................30 L Focus frame .......................................... 67, 75, 76 M Temperature warning .....................................144 * Shows “9999” if there is space for over 9999 frames. 9 Parts of the Camera ■ Shooting: Electronic Viewfinder/LCD Monitor 12/31/2050 10:00 AM 10 Parts of the Camera N Temperature warning .....................................144 O Control lock.........................................................3 P Virtual horizon ..................................................34 Q Histogram.........................................................34 R Distance indicator .............................................63 S Battery level .....................................................25 T Sensitivity.........................................................58 U Exposure compensation ....................................57 V Aperture ............................................... 35, 37, 38 W Shutter speed ....................................... 35, 36, 38 X AE lock indicator ...............................................76 Y Metering...........................................................59 Z Shooting mode ................................35, 36, 37, 38 a Focus indicator..................................................64 b Manual focus indicator .....................................64 c Focus mode ......................................................63 d AF+MF indicator ..............................................93 e Shutter type......................................................96 f Continuous mode ....................................... 52, 53 g Exposure indicator ...................................... 38, 57 h Self-timer indicator ..........................................73 i Microphone/remote release ................. 45, 72, 99 j Flash mode .......................................................78 Flash compensation ..........................................98 k IS mode ............................................................96 Before You Begin A Focus check.......................................................64 B Depth-of-field preview .....................................37 C Location data download status .......................117 D Movie mode................................................ 44, 99 E Time remaining ................................................44 F Card slot options ....................................... 23, 116 G Number of available frames * .........................145 H Image quality and size ......................................88 I Date and time ............................................. 26, 27 J Focus frame .......................................... 67, 75, 76 K White balance...................................................61 L Film simulation.................................................60 M Dynamic range .................................................89 * Shows “9999” if there is space for over 9999 frames. Control Lock X Pressing a locked control (P (P 3) displays a X icon. 11 Parts of the Camera ■ Playback 12/31/2050 10:00 AM A Date and time ............................................. 26, 27 B Face detection indicator....................................92 C Red-eye removal indicator..............................104 D Advanced filter .................................................55 E Location data ..................................................117 F Protected image .............................................103 G Card slot.................................................... 39, 102 H Frame number ................................................115 12 I Gift image.........................................................39 J Photobook assist indicator ................................85 K DPOF print indicator .......................................126 L Battery level .....................................................25 M Image size/quality ............................................88 N Film simulation.................................................60 O Dynamic range .................................................89 P White balance...................................................61 Q Sensitivity.........................................................58 R Exposure compensation ....................................57 S Aperture ............................................... 35, 37, 38 T Shutter speed ....................................... 35, 36, 38 U Playback mode indicator...................................39 V Movie icon ........................................................46 W Rating ...............................................................39 Lenses The camera can be used with lenses for the FUJIFILM X-mount. Parts of the Lens Before You Begin Removing the Caps Remove the caps as shown. Q Lens caps may differ from those shown. A Lens hood B Mounting marks C Focus ring D Zoom ring E Aperture ring F O.I.S. switch G Aperture mode switch H Lens signal contacts I Front lens cap J Rear lens cap Attaching the Hood When attached, lens hoods reduce glare and protect the front lens element. 13 Lenses Lenses with Aperture Rings At settings other than A, you can adjust aperture by rotating the lens aperture ring (exposure modes A and M). Aperture ring A 16 11 8 5.6 4 2.8 A 16 11 8 5.6 4 Lenses with No Aperture Rings The method used to adjust aperture can be selected using D BUTTON/DIAL SETTING > APERTURE SETTING (P 113). When an option other than AUTO is selected, aperture can be adjusted using the rear command dial. The Aperture Mode Switch If the lens has an aperture mode switch, aperture can be adjusted manually by sliding the switch to Z and rotating the aperture ring. Aperture ring R Aperture control defaults to the rear command dial, but can be reassigned to the front command dial using D BUTTON/DIAL SETTING > COMMAND DIAL SETTING (P 112). Aperture mode switch Q When the aperture ring is set to A, rotate the rear command dial to adjust aperture. 14 Lenses O.I.S. switch Manual Focus Lenses Slide the focus ring to the front for autofocus. For manual focus, slide the focus ring to the back and rotate it while checking the results in the camera display. The focus distance and depth-of-field indicators can be used to assist manual focus. Note that manual focus may not be available in all shooting modes. Before You Begin Lenses with O.I.S. Switches If the lens supports optical image stabilization (O.I.S.), the image stabilization mode can be chosen in the camera menus. To activate image stabilization, slide the O.I.S. switch to ON. The Depth-of-Field Indicator The depth-of-field indicator shows the approximate depth of field (the distance in front of and behind the focus point that appears to be in focus). Distance indicator R The indicator is displayed in film format (P 37). 15 First Steps Attaching the Strap Attach the strap clips to the camera and then attach the strap. 1 Open a strap clip. Use the clip attaching tool to open a strap clip, making sure that the tool and clip are in the orientations shown. 3 Pass the clip through the eyelet. Rotate the clip fully through the eyelet until it clicks closed. 4 Attach a protective cover. Q Keep the tool in a safe place. You will need it to open the strap clips when removing the strap. 2 Place the strap clip on an eyelet. Hook the strap eyelet in the clip opening. Remove the tool, using the other hand to keep the clip in place. 16 Place a protective cover over the eyelet as shown, with the black side of the cover toward the camera. Repeat Steps 1–4 for the second eyelet. Attaching the Strap 5 Insert the strap. Insert the strap through a protective cover and strap clip. 6 Fasten the strap. Fasten the strap as shown. Repeat Steps 5–6 for the second eyelet. First Steps Q To avoid dropping the camera, be sure the strap is correctly secured. 17 Attaching a Lens Lenses attach as described below. Q Care is required to prevent dust or other particles from entering the camera while attaching and removing lenses. 1 Remove the body and rear caps. Remove the body cap from the camera and the rear cap from the lens. Removing Lenses To remove the lens, turn the camera off, then press the lens release button and rotate the lens as shown. Lens release button Q Do not touch the camera’s internal parts. 2 Attach the lens. Place the lens on mount, keeping the marks on the lens and camera aligned, and then rotate the lens until it clicks into place. Q Do not press the lens release button while attaching the lens. 18 Q To prevent dust accumulating on the lens or inside the camera, replace the lens caps and camera body cap when the lens is not attached. Lenses and Other Optional Accessories The camera can be used with lenses for the FUJIFILM X-mount and the other accessories listed from page 131. Charging the Battery The battery is not charged at shipment. Before use, charge the battery in the supplied battery charger. 1 Place the battery in the charger. Place the battery in the supplied battery charger as shown. Charge lamp Plug the charger into an indoor power outlet. The charging indicator will light. The Charging Indicator The charging indicator shows battery charge status as follows: Charging indicator Arrow On Battery not inserted. Battery fully charged. Battery charging. Blinks Battery fault. Off Battery The camera uses an NP-W126 rechargeable battery. R The supplied AC cord is for use exclusively with the supplied battery charger. Do not use the supplied charger with other cords or the supplied cord with other devices. Battery status Action First Steps Battery charger 2 Plug the charger in. Insert the battery. Remove the battery. — Unplug the charger and remove the battery. 3 Charge the battery. Remove the battery when charging is complete. See the specifications (P 151) for charging times (note that charging times increase at low temperatures). Q Unplug the charger when it is not in use. 19 Inserting the Battery After charging the battery, insert the battery in the camera as described below. 1 Open the battery-chamber cover. Slide the battery-chamber latch as shown and open the battery-chamber cover. 2 Insert the battery. Using the battery to keep the battery latch pressed to one side, insert the battery contacts first in the direction shown by the arrow. Confirm that the battery is securely latched. Arrow Q Do not open the battery-chamber cover when the camera is on. Failure to observe this precaution could damage image files or memory cards. Q Do not use excessive force when handling the battery-chamber cover. Battery latch Q Insert the battery in the orientation shown. Do not use force or attempt to insert the battery upside down or backwards. The battery will slide in easily in the correct orientation. 3 Close the battery-chamber cover. 20 Inserting the Battery Battery latch Q The battery may become hot when used in hightemperature environments. Observe caution when removing the battery. Q Batteries • Remove dirt from the battery terminals with a clean, dry cloth. Failure to observe this precaution could prevent the battery from charging. • Do not affix stickers or other objects to the battery. Failure to observe this precaution could make it impossible to remove the battery from the camera. • Do not short the battery terminals. The battery could overheat. • Read the cautions in “The Battery and Power Supply” (P v). • Use only battery chargers designated for use with the battery. Failure to observe this precaution could result in product malfunction. • Do not remove the labels from the battery or attempt to split or peel the outer casing. • The battery gradually loses its charge when not in use. Charge the battery one or two days before use. First Steps Removing the Battery Before removing the battery, turn the camera off and open the battery-chamber cover. To remove the battery, press the battery latch to the side, and slide the battery out of the camera as shown. 21 Inserting Memory Cards The camera has no internal memory; instead, pictures are stored on optional SD, SDHC, and SDXC memory cards (sold separately). The camera can be used with two cards, one in each of its two slots. Movies are recorded only to the card in the first slot, which supports UHS-II. Q Be sure card is in the correct orientation; do not 1 Open the memory card slot cover. insert at an angle or use force. Q SD/SDHC/SDXC memory cards can be locked, making it impossible to format the card or to Write-protect switch record or delete images. Before inserting a memory card, slide the writeprotect switch to the unlocked position. Q Do not open the memory card slot cover when the camera is on. Failure to observe this precaution could damage image files or memory cards. 2 Insert a memory card. Holding the memory card in the orientation shown, slide it in until it clicks into place at the back of the first slot (if you are using two cards, insert the second card into second slot). Click! 22 3 Close the memory card slot cover. Removing Memory Cards Before removing memory cards, turn the camera off and open the memory card slot cover. To remove a memory card, press it in and release it slowly. Press center of card The card can then be removed by hand. When a memory card is removed, the card could be ejected too quickly. Use your finger to hold it and gently release the card. Inserting Memory Cards Using Two Cards At default settings, the card in the second slot is used only if the card in the first slot is full (SEQUENTIAL). This can be changed using D SAVE DATA SETTING > CARD SLOT SETTING (STILL IMAGE) (P 116). Option Description The card in the second slot is used only when the card in the first slot is full. R If the second slot is selected for D SAVE DATA SETTING > SWITCH SLOT (SEQUENTIAL), recording will start on the card in the second slot and switch to the first slot when the card in the second slot is full. BACKUP Each picture is recorded twice, once to each card. RAW/JPEG As for SEQUENTIAL SEQUENTIAL, except that the RAW copy of pictures taken with FINE + RAW or NORMAL + RAW selected for H IMAGE QUALITY SETTING > IMAGE QUALITY will be saved to the card in the first slot and the JPEG copy to the card in the second slot. First Steps SEQUENTIAL (default) Display Movies Regardless of the option selected for CARD SLOT SETTING (STILL IMAGE), movies will be recorded to the card in the first slot; if SEQUENTIAL is selected, movies will be recorded to the card in the first slot even after recording has moved on to the card in the second slot. 23 Inserting Memory Cards ■ Compatible Memory Cards FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved for use in the camera; UHS-II cards can be used in the first slot. A complete list of approved memory cards is available at http://www.fujifilm.com/support/digital_cameras/compatibility/. Operation is not guaranteed with other cards. The camera can not be used with xD-Picture Cards or MultiMediaCard (MMC) devices. Q Memory Cards • Do not turn the camera off or remove the memory card while the memory card is being formatted or data are being recorded to or deleted from the card. Failure to observe this precaution could damage the card. • Format memory cards before first use, and be sure to reformat all memory cards after using them in a computer or other device. For more information on formatting memory cards, see page 107. • Memory cards are small and can be swallowed; keep out of reach of children. If a child swallows a memory card, seek medical assistance immediately. • miniSD or microSD adapters that are larger or smaller than the standard dimensions of an SD/SDHC/SDXC card may not eject normally; if the card does not eject, take the camera to an authorized service representative. Do not forcibly remove the card. • Do not affix labels to memory cards. Peeling labels can cause camera malfunction. • Movie recording may be interrupted with some types of SD/SDHC/SDXC memory card. Use a UHS speed class 1 card or better for movies and burst photography. • Formatting a memory card in the camera creates a folder in which pictures are stored. Do not rename or delete this folder or use a computer or other device to edit, delete, or rename image files. Always use the camera to delete pictures; before editing or renaming files, copy them to a computer and edit or rename the copies, not the originals. Renaming the files on the camera can cause problems during playback. 24 Turning the Camera on and Off Rotate the ON/OFF switch to ON to turn the camera on. Select OFF to turn the camera off. Q Fingerprints and other marks on the lens or viewfinder can affect pictures or the view through the viewfinder. Keep the lens and viewfinder clean. First Steps R Press the a button to start playback. Press the shutter button halfway to return to shooting mode. R The camera will turn off automatically if no operations are performed for the length of time selected for D POWER MANAGEMENT > AUTO POWER OFF (P 114). To reactivate the camera after it has turned off automatically, press the shutter button halfway or turn the ON/OFF switch to OFF and then back to ON. Battery Level After turning the camera on, check the battery level in the display. Indicator e f g h i i (red) j (blinks red) Description Battery partially discharged. Battery about 80% full. Battery about 60% full. Battery about 40% full. Battery about 20% full. Low battery. Charge as soon as possible. Battery exhausted. Turn camera off and recharge battery 25 Basic Setup A language-selection dialog is displayed the first time the camera is turned on. 1 Choose a language. Highlight a language and press MENU/OK. R Press DISP/BACK to skip the current step. Any steps you skip will be displayed the next time the camera is turned on. 2 Set the date and time. DATE/TIME NOT SET 2018 Y Y .MM.DD 2017 2016 2015 2014 AM SET NO Press the selector left or right to highlight the year, month, day, hour, or minute and press up or down to change. To change the order in which the year, month, and day are displayed, highlight the date format and press the selector up or down. Press MENU/OK to exit to shooting mode when settings are complete. R If the battery is removed for an extended period, the camera clock will be reset and the language-selection dialog will be displayed when the camera is turned on. 26 Basic Setup Changing Basic Settings To change the language or reset the clock: 1 Display the desired option. Display the setup menu and select D USER SETTING > a to change the language or DATE/TIME to reset the clock (P 106). To choose a language, highlight the desired option and press MENU/OK. To set the clock, press the selector left or right to highlight the year, month, day, hour, or minute and press up or down to change, then press MENU/OK once the clock has been set to your satisfaction. First Steps 2 Adjust settings. 27 Display Settings The camera is equipped with a hybrid optical/electronic viewfinder (OVF/EVF) and an LCD monitor (LCD). Choosing a Display Press the VIEW MODE button to cycle through displays as shown below. VIEW FINDER VIEW FINDER E EYE SENSOR: SENSOR Automatic display selection using eye sensor VIEWFINDER ONLY + E: Viewfinder only; eye sensor turns display on or off VIEWFINDER ONLY: Viewfinder only LCD VIEW FINDER LCD LCD ONLY: LCD monitor only The Eye Sensor The eye sensor turns the viewfinder on when you put your eye to the viewfinder and turns it off when you take your eye away (note that the eye sensor may respond to objects other than your eye or to light shining directly on the sensor). If automatic display selection is enabled, the LCD monitor will turn on when the viewfinder turns off. 28 Eye sensor Display Settings The Viewfinder Selector Use the viewfinder selector to switch between the electronic viewfinder (EVF), the optical viewfinder (OVF), and a dual optical viewfinder/electronic range finder (ERF) display. First Steps 3 2 1 0 -1 -2 -3 3 2 1 0 -1 -2 -3 P P EVF P OVF ERF (dual display) The OVF Display Keep the selector pressed up to choose the optical viewfinder display zoom ratio. 29 Display Settings The Hybrid (EVF/OVF/ERF) Viewfinder The features of the different displays are described below. Display Description The optical display is sharp and free of blur so that your subject’s expression is always visible. In addition, the OVF shows the area just outside the frame, making it easier to compose shots on the fly. Because the viewfinder OVF window is a slight distance from the lens, the area visible in photographs may however differ slightly from the display in the viewfinder due to parallax. The live view display gives you a preview of the final picture (including depth of field, focus, exposure, and white EVF balance) with exactly the same frame coverage. ERF As for the optical viewfinder but with a focus preview. A magnified view of an area of the frame including the (dual display) current focus position is shown at the bottom right corner of the display. Bright Frame Simulation The angle of view covered by the bright frame in the OVF display varies with the focal length of the lens. Pressing a function button (by default, Fn2) displays a bright frame simulation that shows the area covered by the bright frame at different focal lengths. R Keep the viewfinder selector pressed up to toggle between the bright frames for maximum and minimum aperture. 90 32 27 23 18 Wide (0.36 ×) 30 60 56 Focal length 35 Tele (0.6 ×) Display Settings The Viewfinder Display When ON is selected for D SCREEN SETTING > EVF AUTOROTATE DISPLAYS (P 110), the indicators in the viewfinder automatically rotate to match camera orientation. First Steps Focusing the Viewfinder The camera is equipped with diopter adjustment in the range –4 to +2 m–1 to accommodate individual differences in vision. Rotate the diopter adjustment control until the viewfinder display is in sharp focus. Orientation changed from “wide” to “tall” Diopter adjustment control Q The display in the LCD monitor is unaffected. Adjusting Display Brightness The brightness and hue of the viewfinder and LCD monitor can be adjusted using the options under D SCREEN SETTING. Choose EVF BRIGHTNESS or EVF COLOR to adjust viewfinder brightness or hue (P 110), LCD BRIGHTNESS or LCD COLOR to do the same for the LCD monitor (P 110). 31 The DISP/BACK Button The DISP/BACK button controls the display of indicators in the viewfinder and LCD monitor. ■ Shooting: Optical Viewfinder Standard ■ LCD Monitor: Shooting Information off Standard Information off 3 2 1 0 -1 -2 -3 P ■ Shooting: Electronic Viewfinder Standard Information off Info display P 32 The DISP/BACK Button ■ Customizing the Standard Display To choose the items shown in the standard display: 1 Display standard indicators. Press the DISP/BACK button until standard indicators are displayed. First Steps 2 Select DISP. CUSTOM SETTING. Select D SCREEN SET-UP > DISP. CUSTOM SETTING (P 111) in the setup menu. 3 Choose a display. Highlight OVF or EVF/LCD and press MENU/OK. 4 Choose items. Highlight items and press MENU/OK to select or deselect. Option FRAMING GUIDELINE ELECTRONIC LEVEL FOCUS FRAME AF DISTANCE INDICATOR MF DISTANCE INDICATOR HISTOGRAM SHOOTING MODE APERTURE/S-SPEED/ISO OVF EVF w w w w R R w w R R w w R R R R Option INFORMATION BACKGROUND Expo. Comp. (Digit) Expo. Comp. (Scale) FOCUS MODE PHOTOMETRY SHUTTER TYPE FLASH CONTINUOUS MODE OVF EVF — R w w R R R R R R R R R R R R Option DUAL IS MODE WHITE BALANCE FILM SIMULATION DYNAMIC RANGE FRAMES REMAINING IMAGE SIZE/QUALITY MOVIE MODE & REC. TIME BATTERY LEVEL OVF EVF R R R R R R R R R R R R w R R R 5 Save changes. Press DISP/BACK to save changes. 6 Exit the menus. Press DISP/BACK as needed to exit the menus and return to the shooting display. R See page 8 for the locations of these items in the displays. 33 The DISP/BACK Button Virtual Horizon Selecting ELECTRONIC LEVEL displays a virtual horizon. The camera is level when the two lines overlap. R The virtual horizon may not be displayed if the camera lens is pointed up or down. ■ Viewfinder/LCD Monitor: Playback Standard Information off Info display 12/31/2050 10:00 AM Favorites 12/31/2050 10:00 AM 102/31/2050 10:00 AM FAVORITES Histograms Histograms show the distribution of tones in the image. Brightness is shown by the horizontal axis, the number of pixels by the vertical axis. Shadows Highlights Optimal exposure: Pixels are distributed in an even curve throughout the tone range. Overexposed: Pixels are clustered on the right side of the graph. No. of pixels Pixel brightness 34 Underexposed: Pixels are clustered on the left side of the graph. Basic Photography and Playback Program AE (P) To allow the camera to adjust both shutter speed and aperture for optimal exposure, set shutter speed and aperture to A. P will appear in the display. Q If the subject is outside the metering range of the camera, the shutter speed and aperture displays will show “– – –”. Aperture mode switch Program Shift If desired, you can rotate the front or rear command dial to select other combinations of shutter speed and aperture without altering exposure (program shift). Program shift is not available if the attached flash supports TTL auto, or if an auto option is selected for H IMAGE QUALITY SETTING > DYNAMIC RANGE (P 89). To cancel program shift, turn the camera off. Shutter speed Aperture Basic Photography and Playback 35 Shutter-Priority AE (S) To adjust shutter speed manually while letting the camera select aperture for optimal exposure, set aperture to A and use the shutter speed dial (if A is currently selected for shutter speed, press the dial lock release while rotating the shutter speed dial). S will appear in the display. Aperture mode switch R Shutter speed can also be adjusted in increments of 1/3 EV by rotating the front command dial. Shutter speed can be adjusted even while the shutter button is pressed halfway. Q If the correct exposure can not be achieved at the selected shutter speed, aperture will be displayed in red when the shutter button is pressed halfway. Adjust shutter speed until the correct exposure is achieved. Q If the subject is outside the metering range of the camera, the aperture display will show “– – –”. 36 Aperture-Priority AE (A) To adjust aperture manually while letting the camera select shutter speed for optimal exposure, rotate the shutter speed dial to A and adjust aperture as desired. A will appear in the display. R Aperture can be adjusted even while the shutter button is pressed halfway. Aperture mode switch Previewing Depth of Field When L PREVIEW DEPTH OF FIELD is assigned to a function button (P 51), pressing the button stops aperture down to the selected setting, allowing depth of field to be previewed in the display. Depth of field can also be previewed using the depth-of-field indicator in the standard display (P 33). Press DISP/BACK to cycle through display modes until standard indicators are displayed. R Use the G AF/MF SETTING > DEPTH-OF-FIELD SCALE option (P 94) to choose how depth of field is displayed. Choose FILM FORMAT BASIS to help you make practical assessments of depth of field for pictures that will be viewed as prints and the like, PIXEL BASIS to help you assess depth of field for pictures that will be viewed at high resolutions on computers or other electronic displays. Basic Photography and Playback Q If the correct exposure can not be achieved at the selected aperture, the shutter speed will be displayed in red when the shutter button is pressed halfway. Adjust aperture until the correct exposure is achieved. Q If the subject is outside the metering range of the camera, the shutter speed display will show “– – –”. Depth of field 37 Manual Exposure (M) Exposure can be altered from the value suggested by the camera by setting both shutter speed and aperture to values other than A (if A is currently selected for shutter speed, press the dial lock release while rotating the shutter speed dial). M will appear in the display. R Shutter speed can also be adjusted in increments of 1/3 EV by rotating the front command dial. Aperture mode switch Exposure indicator 㹋 Exposure Preview To preview exposure in the LCD monitor, select an option other than OFF for D SCREEN SETTING > PREVIEW EXP./WB IN MANUAL MODE (P 110). Select OFF when using the flash or on other occasions on which exposure may change when the picture is taken. 38 Viewing Pictures Viewing Pictures Full Frame Pictures can be viewed in the viewfinder or LCD monitor. When taking important pictures, take a test shot and check the results. To view pictures full frame, press a. 100-0001 R Pictures taken using other cameras are marked with a m (“gift image”) icon to warn that they may not display correctly and that playback zoom may not be available. Favorites: Rating Pictures To rate the current picture, press DISP/BACK and press the selector up and down to select from zero to five stars. Basic Photography and Playback Additional pictures can be viewed by pressing the selector left or right or rotating the front command dial. Press the selector or rotate the dial right to view pictures in the order recorded, left to view pictures in reverse order. Keep the selector pressed to scroll rapidly to the desired frame. Two Memory Cards If two memory cards are inserted, you can press and hold the a button to choose a card for playback. R You can also select a card using the C PLAYBACK MENU > SWITCH SLOT option (P 102). 39 Viewing Pictures Viewing Photo Information The photo information display changes each time the selector is pressed up. Basic data Info display 1 12/31/2050 10:00 AM 102/31/2050 10:00 AM LENS FOCAL LENGTH COLOR SPACE LENS MODULATION OPT. S.S 1/4000 F 5.6 ISO 400 23.0mm F5.6 23.0mm sRGB ON +21/3 NEXT Info display 2 40 R Rotate the front command dial to view other images. Zooming in on the Focus Point Press the center of the rear command dial to zoom in on the focus point. Press again to return to fullframe playback. Viewing Pictures Playback Zoom Rotate the rear command dial right to zoom in on the current picture, left to zoom out (to view multiple images, rotate the dial left when the picture is displayed full frame; P 42). When the picture is zoomed in, the selector can be used to view areas of the image not currently visible in the display. To exit zoom, press DISP/BACK, MENU/OK, or the center of the rear command dial. Zoom indicator R The maximum zoom ratio varies with image size (P 88). Playback zoom is not available with cropped or resized copies saved at a size of a (P 102, 103). Basic Photography and Playback Navigation window shows portion of image currently displayed 41 Viewing Pictures Multi-Frame Playback To change the number of images displayed, rotate the rear command dial left when a picture is displayed full frame. Rotate left to view more images. 100-0001 Rotate right to view fewer images. Use the selector to highlight images and press MENU/OK to view the highlighted image full frame (to zoom in on the selected image, rotate the rear command dial right when the picture is displayed full frame; P 41). In the nine- and hundred-frame displays, press the selector up or down to view more pictures. 42 Deleting Pictures To delete individual pictures, multiple selected pictures, or all pictures, press the b button when a picture is displayed full frame and choose from the options below. Note that deleted pictures can not be recovered. Copy important pictures to a computer or other storage device before proceeding. ERASE FRAME SELECTED FRAMES ALL FRAMES FRAME SELECTED FRAMES ALL FRAMES Description Press the selector left or right to scroll through pictures and press MENU/OK to delete the current picture (a confirmation dialog is not displayed). Highlight pictures and press MENU/OK to select or deselect (pictures in photobooks or print orders are shown by S). When the operation is complete, press DISP/BACK to display a confirmation dialog, then highlight OK and press MENU/OK to delete the selected pictures. A confirmation dialog will be displayed; highlight OK and press MENU/OK to delete all unprotected pictures. Pressing DISP/BACK cancels deletion; note that any pictures deleted before the button was pressed can not be recovered. R Protected pictures can not be deleted. Remove protection from any pictures you wish to delete (P 103). R Pictures can also be deleted from the menus using the C PLAY BACK MENU > ERASE option (P 102). R If a message appears stating that the selected images are part of a DPOF print order, press MENU/OK to delete the pictures. Basic Photography and Playback Option 43 Basic Movie Recording and Playback Recording Movies The camera can be used to record short high-definition movies. Sound is recorded in stereo via the built-in microphone; do not cover the microphone during recording. Q Movies are recorded to the card in the first slot. Be sure a card is inserted in the first slot before proceeding. 1 Press the movie-record (Fn1) button to start recording. Recording indicator Time remaining 2 Press the button again to end recording. Recording ends automatically when the maximum length is reached or the memory card is full. 44 R Zoom can be adjusted while recording is in progress. R Frame size and rate can be selected using W MOVIE SETTING > MOVIE MODE (P 99). Focus mode is selected using the focus mode selector (P 63); for continuous focus adjustment, select C, or choose S and enable Intelligent Face Detection (P 92). Intelligent Face Detection is not available in focus mode M. R During recording, exposure compensation can be adjusted by up to ±2 EV. R The indicator lamp lights while movies are being recorded. Recording Movies Q If the lens is equipped with an aperture mode switch, select the aperture mode before beginning recording. If an option other than A is selected, shutter speed and aperture can be adjusted while recording is in progress. Q The microphone may pick up lens noise and other sounds made by the camera during recording. Q Vertical or horizontal streaks may appear in movies containing very bright subjects. This is normal and does not indicate a malfunction. R The dialog shown at right will be displayed when a microphone is connected to the microphone/ remote release connector. Press MENU/OK and select MIC/REMOTE RELEASE > m MIC. CHECK MIC/REMOTE RELEASE SETTING SKIP SET Basic Movie Recording and Playback Depth of Field Adjust aperture before recording begins. Choose low f-numbers to soften background details. Using an External Microphone Sound can be recorded with external microphones that connect using jacks 2.5 mm in diameter; microphones that require bus power can not be used. See the microphone manual for details. 45 Viewing Movies During playback, movies are displayed as shown at right. The following operations can be performed while a movie is displayed: 12/31/2050 10:00 AM Operation Description Press the selector down to start playback. Press again to pause. While playback is Start/pause playback paused, you can press the selector left or right to rewind or advance one frame Movie icon at a time. End playback Press the selector up to end playback. Adjust speed Press the selector left or right to adjust playback speed during playback. Press MENU/OK to pause playback and display volume controls. Press the selector up Adjust volume or down to adjust the volume; press MENU/OK again to resume playback. Volume can also be adjusted using D SOUND SETTING > PLAYBACK VOLUME (P 109). PLAY ±0 Progress is shown in the display during playback. Progress bar 29m59s Q Do not cover the speaker during playback. STOP PAUSE Playback Speed Press the selector left or right to adjust playback speed during playback. Speed is shown by the Arrow number of arrows (M or N). 29m59s STOP 46 PAUSE The Q (Quick Menu) Button Using the Q Button Press Q for quick access to selected options. The Quick Menu Display At default settings, the quick menu contains the following items. SELECT CUSTOM SETTING BASE SET A SELECT CUSTOM SETTING B AF MODE C DYNAMIC RANGE D WHITE BALANCE E NOISE REDUCTION F IMAGE SIZE G IMAGE QUALITY H FILM SIMULATION I HIGHLIGHT TONE J SHADOW TONE K COLOR L SHARPNESS M SELF-TIMER N FACE/EYE DETECTION SETTING O FLASH MODE P EVF/LCD BRIGHTNESS The Q (Quick Menu) Button The quick menu shows the options currently selected for items B—P, which can be changed as described on page 49. The H IMAGE QUALITY SETTING > SELECT CUSTOM SETTING item (item A) shows the current custom settings bank: • q: No custom settings bank selected. • t — u: Select a bank to view the settings saved using the H IMAGE QUALITY SETTING > EDIT/ SAVE CUSTOM SETTING option (P 82). • r — s: The current custom settings bank. 47 Using the Q Button Viewing and Changing Settings 1 Press Q to display the quick menu during shooting. SELECT CUSTOM SETTING BASE SET 2 Use the selector to highlight items and rotate the rear command dial to change. R Changes are not saved to the current settings bank (P 47). Settings that differ from those in the current settings bank (t — u) are shown in red. 3 Press Q to exit when settings are complete. 48 Using the Q Button Editing the Quick Menu To choose the items displayed in the quick menu: 1 Press and hold the Q button during shooting. SELECT CUSTOM SETTING SET END 2 The current quick menu will be displayed; use the selector to highlight the item you wish to change and press MENU/OK. You will be given the following choice of items to assign to the selected position: SELECT CUSTOM SETTING * DYNAMIC RANGE * WHITE BALANCE * NOISE REDUCTION * IMAGE SIZE IMAGE QUALITY FILM SIMULATION * • • • • • • • GRAIN EFFECT * HIGHLIGHT TONE * SHADOW TONE * COLOR * SHARPNESS * SELF-TIMER FACE/EYE DETECTION SETTING • • • • • • • PHOTOMETRY AF MODE FLASH MODE FLASH COMPENSATION MF ASSIST MOVIE MODE MIC LEVEL ADJUSTMENT • • • • EVF/LCD BRIGHTNESS EVF/LCD COLOR SHUTTER TYPE NONE * Stored in custom settings bank. R Select NONE to assign no option to the selected position. When SELECT CUSTOM SETTING is selected, current settings are shown in the quick menu by the label BASE. The Q (Quick Menu) Button • • • • • • • 3 Highlight the desired item and press MENU/OK to assign it to the selected position. R The quick menu can also be edited using D BUTTON/DIAL SETTING > EDIT/SAVE QUICK MENU (P 112). 49 The Fn (Function) Buttons Using the Function Buttons The roles played by each of the six function buttons can be selected by pressing and holding the button. The default options are shown below: 50 Fn1 button Fn2 button Fn3 button Recording movies (P 44) Bright frame simulation (P 30) Metering (P 59) Fn4 button Fn5 button Fn6 button Film simulation (P 60) White balance (P 61) AF mode (P 66) Using the Function Buttons Assigning Roles to the Function Buttons To assign roles to the function buttons, press and hold the DISP/BACK button until the menu below is displayed. Select buttons to choose their roles. FUNCTION (Fn) SETTING SET PREVIEW DEPTH OF FIELD ISO AUTO SETTING SELF-TIMER IMAGE SIZE IMAGE QUALITY DYNAMIC RANGE FILM SIMULATION • • • • • • • GRAIN EFFECT WHITE BALANCE PHOTOMETRY AF MODE FOCUS AREA FLASH MODE FLASH COMPENSATION • • • • • • • SELECT CUSTOM SETTING MOVIE FACE/EYE DETECTION SETTING RAW APERTURE SETTING WIRELESS COMMUNICATION SHUTTER TYPE • • • • • PREVIEW EXP./WB IN MANUAL MODE PREVIEW PIC. EFFECT BRIGHT FRAME SIMULATOR BRIGHT FRAME BRIGHTNESS NONE R To disable the selected button, choose NONE. R You can also display options for any of the function buttons by pressing and holding the button. R The roles played by the six function buttons can also be selected using D BUTTON/DIAL SETTING > FUNCTION (Fn) SETTING (P 112). The Fn (Function) Buttons • • • • • • • CANCEL 51 More on Photography and Playback Drive Mode Use the DRIVE (e) button to choose the drive mode. 1 Press the DRIVE (e) button to display drive 2 Press the selector up or down to highlight a drive mode. Icon B R O W X H Y j Y 52 Drive mode STILL IMAGE CONTINUOUS AE BKT ISO BKT FILM SIMULATION BKT WHITE BALANCE BKT DYNAMIC RANGE BKT MULTIPLE EXPOSURE ADVANCED FILTER 3 Press the selector left or right to choose a setting. • Burst mode (CONTINUOUS): Choose the frameadvance rate. • AE/ISO/WB BKT: Choose the bracketing increment. • ADVANCED FILTER: Choose a filter effect. • Other modes: Proceed to Step 4. mode options. 4 Press MENU/OK. AE BKT 5 Take pictures. P — 53 54 56 55 R In burst mode, pictures will be taken while the shutter button is pressed. Shooting ends when the button is released, the maximum number of pictures has been taken, or the memory card is full. Drive Mode R Frame rate varies with the subject, shutter speed, sensitivity, and focus mode and may slow as more shots are taken. R Depending on shooting conditions, the frame rate may drop or the flash may not fire. R Additional time may be required to record pictures when shooting ends. R If file numbering reaches 999 before shooting is complete, the remaining pictures will be recorded to a new folder (P 115). R Burst shooting may not begin if the space available on the memory card is insufficient. Focus and Exposure To vary focus and exposure with each shot, select focus mode C; in other modes, focus and exposure are determined by the first shot in each series. More on Photography and Playback R Burst Mode (CONTINUOUS) Capture motion in a series of pictures. Q Selecting 8.0 fps in focus mode C restricts the choice of focus frames (P 70). Q Exposure and focus tracking performance may vary with aperture, sensitivity, and shooting conditions. 53 Drive Mode Bracketing Automatically vary settings over a series of pictures. Option O AE BKT W ISO BKT X FILM SIMULATION BKT H WHITE BALANCE BKT Y DYNAMIC RANGE BKT 54 Description Select a bracketing amount. Each time the shutter button is pressed, the camera will take three shots: one using the metered value for exposure (P 57), the second overexposed by the selected amount, and the third underexposed by the same amount (regardless of the amount selected, exposure will not exceed the limits of the exposure metering system). Select a bracketing amount. Each time the shutter is released, the camera will take a picture at the current sensitivity (P 58) and process it to create two additional copies, one with sensitivity raised and the other with sensitivity lowered by the selected amount (regardless of the amount selected, sensitivity will not exceed ISO 12800 or fall below ISO 200). Each time the shutter is released, the camera takes one shot and processes it to create copies at the settings chosen using A SHOOTING SETTING > FILM SIMULATION BKT (P 60, 95). Select a bracketing amount. Each time the shutter button is pressed, the camera takes three shots: one at the current white balanced setting (P 61), one with fine-tuning increased by the selected amount, and another with fine-tuning decreased by the selected amount. Each time the shutter button is pressed, the camera takes three shots with different dynamic ranges (P 89): 100% for the first, 200% for the second, and 400% for the third. While dynamic range bracketing is in effect, sensitivity will be restricted to a minimum of ISO 800 (or to a minimum of ISO 200 to 800 when an auto option is selected for sensitivity); the sensitivity previously in effect is restored when bracketing ends. Drive Mode Filter G TOY CAMERA H MINIATURE I POP COLOR J HIGH-KEY Z LOW-KEY K DYNAMIC TONE X SOFT FOCUS u PARTIAL COLOR (RED) v PARTIAL COLOR (ORANGE) w PARTIAL COLOR (YELLOW) x PARTIAL COLOR (GREEN) y PARTIAL COLOR (BLUE) z PARTIAL COLOR (PURPLE) Description Choose for a retro toy camera effect. The tops and bottoms of pictures are blurred for a diorama effect. Create high-contrast images with saturated colors. Create bright, low-contrast images. Create uniformly dark tones with few areas of emphasized highlights. Dynamic tone expression is used for a fantasy effect. Create a look that is evenly soft throughout the whole image. Areas of the image that are the selected color are recorded in that color. All other areas of the image are recorded in black-and-white. More on Photography and Playback Y Advanced Filters Take photos with filter effects. R Depending on the subject and camera settings, images may in some cases be grainy or vary in brightness and hue. 55 Drive Mode j Multiple Exposures Create a photograph that combines two exposures. + 1 Select j for drive mode (P 52). 4 Take the second shot, using the first frame as a guide. 2 Take the first shot. EXIT 3 Press MENU/OK. The first shot will be shown superimposed on the view through the lens and you will be prompted to take the second shot. NEXT RETRY 2.0 5 Press MENU/OK to create the multiple exposure, or press the selector left to return to Step 4 and retake the second shot. EXIT R To return to Step 2 and retake the first shot, press the selector left. To save the first shot and exit without creating a multiple exposure, press DISP/BACK. 56 30 RETRY EXIT Exposure Compensation ■ C (Custom) When the exposure compensation dial is rotated to C, exposure compensation can be adjusted by rotating the front command dial. set Exposure compensation indicator Choose positive values (+) to increase exposure R The front command dial can be used to set exposure compensation to values between −5 and +5 EV. R The front command dial can be used to set shutter speed or exposure compensation. Press the dial to toggle between the two. More on Photography and Playback Rotate the exposure compensation dial to adjust exposure when photographing very bright, very dark, or high-contrast subjects. The effect is visible in the display. Choosing an Exposure Compensation Value • Backlit subjects: Choose values from +2/3 EV to +12/3 EV. Choose negative values (–) to reduce exposure Q The amount of compensation available varies with the shooting mode. • Highly reflective subjects or very bright scenes (e.g., snowfields): +1 EV • Scenes that are mostly sky: +1 EV • Spotlit subjects (particularly if photographed against dark backgrounds): –2/3 EV • Subjects with low reflectivity (pine trees or dark-colored foliage): –2/3 EV 57 Sensitivity “Sensitivity” refers to the camera’s sensitivity to light. Lift and rotate the ISO dial to choose from values between 200 and 12800, or select L (100), H (25600), or H (51200) for special situations (P 112). Higher values can be used to reduce blur when lighting is poor, while lower values allow slower shutter speeds or wider apertures in bright light; note, however, that mottling may appear in pictures taken at high sensitivities, particularly at H (51200), while choosing L (100) reduces dynamic range. Values of from ISO 200 to ISO 6400 are recommended in most situations. If A is selected, the camera will adjust sensitivity automatically in response to shooting conditions according to the option selected for A SHOOTING SETTING > ISO AUTO SETTING (P 97). Choose from AUTO 1, AUTO 2, and AUTO 3. R Sensitivity is not reset when the camera is turned off. 58 Metering Q The selected option will only take effect when G AF/MF SETTING > FACE/EYE DETECTION SETTING is off (P 92). Mode Description The camera instantly determines exposure based on an analysis of composition, color, and brightness o distribution. Recommended in most situations. (MULTI) p The camera meters the entire frame but assigns the greatest weight to the area at the center. (CENTER WEIGHTED) The camera meters lighting conditions in an area at the center of the frame equivalent to 2% of the total. v Recommended with backlit subjects and in other cases in which the background is much brighter or (SPOT) darker than the main subject. Exposure is set to the average for the entire frame. Provides consistent exposure across multiple shots w with the same lighting, and is particularly effective for landscapes and portraits of subjects dressed in (AVERAGE) black or white. More on Photography and Playback Choose how the camera meters exposure. Press the function (Fn3) button to display the options shown below, then use the selector to highlight an option and press MENU/OK to select. R Metering options can also be accessed using A SHOOTING SETTING > PHOTOMETRY (P 95). 59 Film Simulation Simulate the effects of different kinds of film, including black-andwhite (with or without color filters). Press the function (Fn4) button to display the options shown below, then use the selector to highlight an option and press MENU/OK to select. Option Description c (PROVIA/STANDARD) Standard color reproduction. Suited to a wide range of subjects, from portraits to landscapes. A high-contrast palette of saturated colors, suited to nature photos. > (Velvia/VIVID) Enhances the range of hues available for skin tones in portraits while preserving the bright blues of daye (ASTIA/SOFT) light skies. Recommended for outdoor portrait photography. i (CLASSIC CHROME) Soft color and enhanced shadow contrast for a calm look. g (PRO Neg. Hi) Offers slightly more contrast than h (PRO Neg. Std). Recommended for outdoor portrait photography. A soft-toned palette. The range of hues available for skin tones is enhanced, making this a good choice for h (PRO Neg. Std) studio portrait photography. Take black-and-white photos with rich gradation and outstanding sharpness. Available with yellow (Ye), a (ACROS) * red (R), and green (G) filters. b (MONOCHROME) * Take pictures in standard black and white. Available with yellow (Ye), red (R), and green (G) filters. Take pictures in sepia. f (SEPIA) * Filters deepen shades of gray corresponding to hues complementary to the selected color. The yellow (Ye) filter deepens purples and blues and the red (R) filter blues and greens. The green (G) filter deepens reds and browns, including skin tones, making it a good choice for portraits. R Film simulation options can be combined with tone and sharpness settings (P 89). R Film simulation options can also be accessed using H IMAGE QUALITY SETTING > FILM SIMULATION (P 89). 60 White Balance Option Description Option Description AUTO White balance adjusted automatically. i For subjects in direct sunlight. k j For subjects in the shade. l Measure a value for white balance (P 62). k Use under “daylight” fluorescent lights. m l Use under “warm white” fluorescent lights. Selecting this option displays a list of color m Use under “cool white” fluorescent lights. temperatures (P 62); highlight a temperan Use under incandescent lighting. k ture and press MENU/OK to select the highlighted option and display the fine-tuning g Reduces the blue cast typically associated with underwater lighting. dialog. WB SHIFT AUTO R:0 B:0 SET More on Photography and Playback For natural colors, choose a white balance option that matches the light source. Press the function (Fn5) button to display the options shown below, then press the selector up or down to highlight an option and press MENU/OK to select. R White balance is adjusted for flash lighting only in AUTO and g modes. Turn the flash off using other white balance options (P 78). R Results vary with shooting conditions. Play pictures back after shooting to check colors. R White balance options can also be accessed using H IMAGE QUALITY SETTING > WHITE BALANCE (P 89). 61 White Balance h: Custom White Balance Choose h to adjust white balance for unusual lighting conditions. White balance measurement options will be displayed; frame a white object so that it fills the display and press the shutter button all the way down to measure white balance (to select the most recent custom value and exit without measuring white balance, press DISP/BACK, or press MENU/OK to select the most recent value and display the fine-tuning dialog). • If “COMPLETED!” is displayed, press MENU/OK to set white balance to the measured value. • If “UNDER” is displayed, raise exposure compensation (P 57) and try again. • If “OVER” is displayed, lower exposure compensation (P 57) and try again. k: Color Temperature Color temperature is an objective measure of the color of a light source, expressed in Kelvin (K). Light sources with a color temperature close to that of direct sunlight appear white; light sources with a lower color temperature have a yellow or red cast, while those with a higher color temperature are tinged with blue. You can match color temperature to the light source as shown in the following table, or choose options that differ sharply from the color of the light source to make pictures “warmer” or “colder.” Choose for redder light sources or “colder” pictures 2,000 K Candlelight Sunset/sunrise 62 Choose for bluer light sources or “warmer” pictures 5,000 K Direct sunlight 15,000 K Blue sky Shade Focus Mode Reduce focus distance 55 35 23 18 Increase focus distance A XF ZOOM 18-55 Focus distance (white line) Manual focus mode icon 㹋 More on Photography and Playback Use the focus mode selector to choose how the camera focuses (note that regardless of the option selected, manual focus will be used when the lens is in manual focus mode). • S (single AF): Focus locks while the shutter button is pressed halfway. Choose for stationary subjects. • C (continuous AF): Focus is continually adjusted to reflect changes in the distance to the subject while the shutter button is pressed halfway. Use for subjects that are in motion. Eye-detection AF is not available. • M (manual): Focus manually using the lens focus ring. Rotate the ring left to reduce the focus distance, right to increase. The manual focus indicator indicates how closely the focus distance matches the distance to the subject in the focus brackets (the white line indicates the focus distance, the blue bar the depth of field, or in other words the distance in front of and behind the focus point that appears to be in focus); you can also check focus visually in the viewfinder or LCD monitor. Choose for manual control of focus or in situations in which the camera is unable to focus using autofocus (P 77). Manual focus indicator Depth of field (blue bar) R Use D BUTTON/DIAL SETTING > FOCUS RING (P 112) to reverse the direction of rotation of the focus ring. R To use autofocus to focus on the subject in the selected focus area (P 67), press the AF-L button (the size of the focus area can be chosen with the rear command dial). In manual focus mode, you can use this feature to quickly focus on a chosen subject using either single or continuous AF according to the option chosen for G AF/MF SETTING > INSTANT AF SETTING (P 93). 63 Focus Mode R The camera can show focus distance in meters or feet. Use D SCREEN SETTING > FOCUS SCALE UNITS (P 111) to choose the units used. R If ON is selected for G AF/MF SETTING > PRE-AF (P 91), focus will be adjusted continuously in modes S and C even when the shutter button is not pressed. ■ The Focus Indicator The focus indicator turns green when the subject is in focus and blinks white when the camera is unable to focus. Brackets (“( )”) indicate that the camera is focusing and are displayed continuously in mode C. j is displayed in manual focus mode. Focus indicator Checking Focus To zoom in on the current focus area (P 67) for precise focus, press the center of the rear command dial. Press the center of the rear command dial again to cancel zoom. In manual focus mode, zoom can be adjusted by rotating the rear command dial when STANM DARD or FOCUS PEAK HIGHLIGHT is selected for G AF/MF SET- M TING > MF ASSIST (P 93), while if ON is selected for G AF/MF SETTING > FOCUS CHECK (P 93), the camera will automatically zoom in on the selected focus area when the focus ring is rotated. Focus zoom is not available in focus mode C or when G AF/MF SETTING > PRE-AF (P 91) is on or an option other than r SINGLE POINT is selected for AF MODE (P 66). 64 Focus Mode R The MF ASSIST menu can be displayed by pressing and holding the center of the rear command dial. The following options are available: • FOCUS PEAK HIGHLIGHT: Highlights high-contrast outlines. Rotate the focus ring until the subject is highlighted. • DIGITAL SPLIT IMAGE: Displays a split image in the center of the frame. Frame the subject in the split-image area and rotate the focus ring until the three parts of the split image are correctly aligned. More on Photography and Playback ■ MF Assist The G AF/MF SETTING > MF ASSIST (P 93) option can be used to check focus when pictures are framed in the LCD monitor or electronic viewfinder in manual focus mode. 65 Focus Mode Autofocus Options (AF Mode) To choose the AF mode for focus modes S and C, press the function button (Fn6) to display the options shown below, then press the selector up or down to highlight an option and press MENU/OK to select. • r SINGLE POINT: The camera focuses on the subject in the selected focus point (P 68). The number of focus points available can be selected using G AF/MF SETTING > NUMBER OF THE FOCUS POINTS (P 91). Use for pin-point focus on a selected subject. • y ZONE: The camera focuses on the subject in the selected focus zone (P 69). Focus zones include multiple focus points (7 × 7, 5 × 5, or 3 × 3), making it easier to focus on subjects that are in motion. • z WIDE/TRACKING: In focus mode C, the camera tracks focus on the subject in the selected focus point while the shutter-release button is pressed halfway (P 70). In focus mode S, the camera automatically focuses on high-contrast subjects; the areas in focus are shown in the display. The camera may be unable to focus on small objects or subjects that are moving rapidly. R AF mode options can also be accessed using G AF/MF SETTING > AF MODE (P 91). 66 Focus Mode R Focus-area selection can also be used to choose the focus point for manual focus and focus zoom. R The focus-area grid is reduced to 9 × 7 at an aspect ratio of 1 : 1 (P 88). Tilt the focus stick to position the focus frame, or press the center of the stick to return to the center focus point. More on Photography and Playback Focus-Point Selection Use the focus stick (focus lever) to choose a focus point for autofocus. The procedure for selecting the focus point varies with the option chosen for AF mode (P 66). Focus frame Available Focus Points Fewer focus points are available for intelligent hybrid AF, which combines phase-detection with TTL contrastdetect AF. TTL contrast-detect Intelligent hybrid AF (TTL contrast-detect AF + phase-detection AF) 67 Focus Mode The Focus Point Display The focus stick (focus lever) can be used to display available focus points. R Focus-area selection can also be accessed using G AF/MF SETTING > FOCUS AREA (P 91). ■ Single Point AF Press the center of the focus stick to display the focus points (“+”) and focus frame. Use the stick to position the focus frame over the desired focus point, or press the center of the stick to return to the center point. Focus point Focus frame To choose the size of the focus frame, rotate the rear command dial. Rotate the dial left to reduce the frame by up to 50%, right to enlarge it by up to 150%, or press the center of the dial to restore the frame to its original size. Press MENU/OK to put your selection into effect. 68 Focus Mode To choose the number of focus frames in the zone, rotate the rear command dial. Rotate the dial right to cycle through zone sizes in the order 3 × 3, 5 × 5, 7 × 7, 3 × 3…, left to cycle through zone sizes in reverse order, or press the center of the dial to select a zone size of 3 × 3. Press MENU/OK to put your selection into effect. Focus zone More on Photography and Playback ■ Zone AF Press the center of the focus stick to display the focus zone. Use the stick to position the zone or press the center of the stick to return the zone to the center of the display. 69 Focus Mode ■ Tracking (Focus Mode C Only) Press the center of the focus stick to display the focus frame. Use the stick to position the focus frame, or press the center of the stick to return the frame to the center of the display. Press MENU/OK to put your selection into effect. The camera will track focus on the subject while the shutter button is pressed halfway. Focus frame Q Manual focus-frame selection is not available when wide/tracking is selected in focus mode S. Burst Mode Focus-Frame Selection When continuous high-speed (8.0 fps) is selected for drive mode, the number of focus frames available in focus mode C drops. Single point 70 Zone Wide/Tracking Long Time-Exposures (T/B) R Use of a tripod is recommended to prevent the camera from moving during the exposure. R To reduce “noise” (mottling) in long time-exposures, select ON for H IMAGE QUALITY SETTING > LONG EXPOSURE NR (P 90). Note that this may increase the time needed to record images after shooting. Time (T) 1 Rotate the shutter speed dial to T. 2 Rotate the front command dial to choose a shutter speed. S 2” Bulb (B) 1 Rotate the shutter speed dial to B. 2 Press the shutter button all the way down. The shutter will remain open for up to 60 minutes while the shutter button is pressed; the display shows the time elapsed since the exposure started. More on Photography and Playback Select a shutter speed of T (time) or B (bulb) for long time-exposures. R Selecting an aperture of A fixes shutter speed at 30 s. 3 Press the shutter button all the way down to take a picture at the selected shutter speed. A count-down timer will be displayed while the exposure is in progress. 71 Long Time-Exposures (T/B) Using a Remote Release An optional RR-90 remote release can be used for long time-exposures. See the manual provided with the RR-90 for more information. Third-Party Remote Releases Electronic releases from thirdparty suppliers can be connected via the microphone/remote release connector. A confirmation dialog will be displayed when a third-party release is connected; press MENU/OK and select n REMOTE for MIC/REMOTE RELEASE. CHECK MIC/REMOTE RELEASE SETTING SKIP SET 72 The Self-Timer 1 Press MENU/OK in shooting mode to display the shooting menu. 4 Press the shutter button halfway to focus. Q Stand behind the camera when using the shutter button. Standing in front of the lens can interfere with focus and exposure. 5 Press the shutter button 2 Select the A SHOOTING SETTING tab (P 87), then highlight SELF-TIMER and press MENU/OK. 3 Press the selector up or down to highlight the desired option and press MENU/OK to select. Option Description The shutter is released two seconds after the shutter button is pressed. Use to reduce blur R 2 SEC caused by the camera moving when the shutter button is pressed. The shutter is released ten seconds after the S 10 SEC shutter button is pressed. Use for photographs in which you wish to appear yourself. OFF Self-timer off. 9 the rest of the way down to start the timer. The display in the monitor shows the number of seconds remaining until the shutter is released. To stop the timer before the picture is taken, press DISP/BACK. More on Photography and Playback Use the timer for self-portraits or to prevent blur caused by camera shake. The self-timer lamp on the front of the camera will blink immediately before the picture is taken. If the two-second timer is selected, the self-timer lamp will blink as the timer counts down. R The self-timer turns off automatically when the camera is turned off. 73 Interval Timer Photography Follow the steps below to configure the camera to take photos automatically at a preset interval. 1 Press MENU/OK in shooting mode to display the shooting menu. Select the A SHOOTING SETTING tab (P 87), then highlight INTERVAL TIMER SHOOTING and press MENU/OK. 2 Use the selector to choose the interval and number of shots. Press MENU/OK to INTERVAL/NUMBER OF TIMES INTERVAL NUMBER OF TIMES proceed. END 3 Use the selector to choose the starting time and then press MENU/OK. Shooting CANCEL START WAITING TIME will start automatically. LATER ESTIMATED START TIME 11 : 00 PM START CANCEL Q Interval timer photography can not be used at a shutter speed of B (bulb) or with multiple exposure photography. In burst mode, only one picture will be taken each time the shutter is released. R Use of a tripod is recommended. R Check the battery level before starting. We recommend using an optional AC-9V AC power adapter and CP-W126 DC coupler. R The display turns off between shots and lights a few seconds before the next shot is taken. The display can be activated at any time by pressing the shutter button. 74 Focusing and Taking Pictures 1 Focus. Frame the picture with your subject in the center of the display and press the shutter button halfway to focus. R If the subject is poorly lit, the AF-assist illuminator may light (P 91). If the camera is able to focus, it will beep twice and the focus indicator and frame in focus will glow green. Focus and exposure will lock while the shutter button is pressed halfway. Focus frame Focus indicator More on Photography and Playback Press the shutter button halfway to focus and the rest of the way down to shoot. If the camera is unable to focus, the focus frame will turn red, s will be displayed, and the focus indicator will blink white. 2 Shoot. Smoothly press the shutter button the rest of the way down to take the picture. 75 Focus/Exposure Lock To compose photographs with off-center subjects: 1 Focus: Position the subject in the focus frame and press the shutter button halfway to lock focus and exposure. Focus and exposure will remain locked while the shutter button is pressed halfway (AF/AE lock). P R Focus and exposure can also be locked with the AF-L and AE-L buttons, respectively (if AE/AF LOCK is selected for D BUTTON/DIAL SETTING > AF-LOCK MODE, pressing the AF-L button will lock both focus and exposure; P 113). 2 Recompose: Keep the shutter button pressed halfway or keep the AF-L or AE-L button pressed. R Focus and/or exposure will remain locked while the AF-L or AE-L button is pressed, whether or not the shutter button is pressed halfway. If AE&AF ON/OFF SWITCH is selected for D BUTTON/DIAL SETTING > AE/AF-LOCK MODE (P 113), focus and/ or exposure lock when the button is pressed and remain locked until the button is pressed again. P 3 Shoot: Press the button all the way down. R The roles of the AE-L and AF-L buttons can be reversed using D BUTTON/DIAL SETTING > AE-L/AF-L BUTTON SETTING (P 113). 76 Focus/Exposure Lock • Fast-moving subjects. • • • • Subjects photographed through a window or other reflective object. Dark subjects and subjects that absorb rather than reflect light, such as hair or fur. Insubstantial subjects, such as smoke or flame. Subjects that show little contrast with the background (for example, subjects in clothing that is the same color as the background). • Subjects positioned in front of or behind a high-contrast object that is also in the focus frame (for example, a subject photographed against a backdrop of highly contrasting elements). More on Photography and Playback Autofocus Although the camera boasts a high-precision autofocus system, it may be unable to focus on the subjects listed below. • Very shiny subjects such as mirrors or car bodies. 77 Flash Photography Use an optional flash unit for additional lighting when shooting at night or indoors under low light. 1 Remove the hot shoe cover and slide the flash onto the hot shoe as shown, stopping when it clicks into place. 2 Turn the flash on. R For more information, see the documentation provided with the flash unit. 78 3 Choose a flash mode in the F FLASH SETTING > FLASH MODE menu (P 87). Mode Description A (AUTO FLASH)/ FLASH)/ The flash fires when required. RecomK (RED EYE REDUCTION) * mended in most situations. The flash fires whenever a picture is N (FORCED FLASH)/ FLASH)/ taken. Use for backlit subjects or for L (FORCED FLASH) * natural coloration when shooting in bright light. Capture both the main subject and F (SLOW SYNCHRO)/ SYNCHRO)/ the background under low light (note M (RED EYE & SLOW) * that brightly lit scenes may be overexposed). l (2ND CURTAIN SYNC.)/ SYNC.)/ The flash fires immediately before the d (2ND CURTAIN SYNC.) * shutter closes. A flash mounted on the hot shoe can be used to control optional remote D (COMMANDER) flash units. The flash does not fire even when the P (SUPPRESSED FLASH) subject is poorly lit. A tripod is recommended. * Red-eye removal is available in these modes when Intelligent Face Detection is active (P 92) and red-eye removal is on (P 98). Red-eye removal minimizes “red-eye” caused when light from the flash is reflected from the subject’s retinas as shown in the illustration at right. Flash Photography Flash Sync Speed The flash will synchronize with the shutter at shutter speeds of 1/250 s or slower. R Lowering the flash turns the flash off (P) and prevents it firing even when the subject is poorly lit; use of a tripod is recommended. Lower the flash where flash photography is prohibited or to capture natural lighting under dim light. We also recommend that you lower the flash when the camera is off. R If p is displayed when the shutter button is pressed halfway, the flash will fire when the photo is taken. R Except in commander mode, the flash may fire several times with each shot. Do not move the camera until shooting is complete. Optional Flash Units The camera can be used with optional FUJIFILM shoe-mounted flash units (P 132). Do not use thirdparty flash units that apply over 300 V to the camera hot shoe. The Sync Terminal Use the sync terminal to connect flash units that require a sync cable. Flash Mode and Shooting Mode The flash modes available vary with the shooting mode (P 153): Flash mode A N F l D P P S A ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ * Wireless remote photography. M ✔ ✔ ✔ ✔ j Y F r* ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ More on Photography and Playback Q Depending on the distance to the subject, some lenses may cast shadows in photos taken with the flash. ✔ ✔ ✔ ✔ ✔ ✔ 79 Recording Pictures in RAW Format To record raw, unprocessed data from the camera image sensor, select a RAW option for image quality in the shooting menu as described below. JPEG copies of RAW images can be created using C PLAY BACK MENU > RAW CONVERSION, or RAW images can be viewed on a computer using the RAW FILE CONVERTER application (P 81, 123). 1 Press MENU/OK in shooting mode to display the shooting menu. Select the H IMAGE QUALITY SETTING tab (P 87), then highlight IMAGE QUALITY (P 88) and press MENU/OK. 2 Highlight an option and press MENU/OK. Select RAW to record only RAW images, or FINE+RAW or NORMAL+RAW to record both JPEG copy together with the RAW images. FINE+RAW uses lower JPEG compression ratios for higher-quality JPEG images, while NORMAL+RAW uses higher JPEG compression ratios to increase the number of images that can be stored. The Function Buttons To toggle RAW image quality on or off for a single shot, assign RAW to a function button (P 51). If a JPEG option is currently selected for image quality, pressing the button temporarily selects the equivalent JPEG+RAW option. If a JPEG+RAW option is currently selected, pressing the button temporarily selects the equivalent JPEG option, while if RAW is selected, pressing the button temporarily selects FINE. Taking a picture or pressing the button again restores the previous setting. 80 Recording Pictures in RAW Format 1 Press MENU/OK during playback to display the playback menu, then press the selector up or down to highlight C PLAY BACK MENU > RAW CONVERSION (P 101) and press MENU/OK to display the settings listed in the table at right. R These options can also be displayed by pressing Q button during playback. 2 Press the selector up or RAW CONVERSION REFLECT SHOOTING COND. PUSH/PULL PROCESSING DYNAMIC RANGE FILM SIMULATION GRAIN EFFECT WHITE BALANCE down to highlight a setting and press the selector right to select. Press the selector up or down to highlight the desired option and press MENU/OK to select and return to the settings list. Repeat this step to adjust additional settings. CREATE CANCEL 3 Press the Q button to preview the JPEG copy and press MENU/OK to save. Setting REFLECT SHOOTING COND. PUSH/PULL PROCESSING Description Create a JPEG copy using the settings in effect at the time the photo was taken. Adjust exposure by –1 EV to +3 EV in increments of 1/3 EV. Enhance details in highlights for natural DYNAMIC RANGE contrast (P 89). Simulate the effects of different types of film FILM SIMULATION (P 60). GRAIN EFFECT Add a film grain effect (P 89). WHITE BALANCE Adjust white balance (P 61). WB SHIFT Fine-tune white balance (P 61). HIGHLIGHT TONE Adjust highlights (P 89). SHADOW TONE Adjust shadows (P 89). COLOR Adjust color density (P 89). SHARPNESS Sharpen or soften outlines (P 89). NOISE REDUCTION Process the copy to reduce mottling (P 89). Improve definition by adjusting for diffracLENS MODULATION tion and the slight loss of focus at the peOPTIMIZER riphery of the lens (P 90). Choose the color space used for color reproCOLOR SPACE duction (P 90). More on Photography and Playback Creating JPEG Copies of RAW Pictures RAW pictures store information on camera settings separately from the data captured by the camera image sensor. Using C PLAY BACK MENU > RAW CONVERSION (P 102), you can create JPEG copies of RAW pictures using different options for the settings listed below. The original image data are unaffected, allowing a single RAW image to be processed in a multitude of different ways. 81 Saving Settings Save up to 7 sets of custom camera settings for commonly-encountered situations. Saved settings can be recalled using H IMAGE QUALITY SETTING > SELECT CUSTOM SETTING (P 90). 1 Press MENU/OK in shooting mode to display the shooting menu. Select the H IMAGE QUALITY SETTING tab (P 87), then highlight EDIT/SAVE CUSTOM SETTING (P 90) and press MENU/OK. 2 Highlight a custom settings bank and press MENU/OK to select. Adjust the following as desired and press DISP/BACK when adjustments are complete: DYNAMIC RANGE, FILM SIMULATION, GRAIN EFFECT, WHITE BALANCE, COLOR, SHARPNESS, HIGHLIGHT TONE, SHADOW TONE, and NOISE REDUCTION. IMAGE QUALITY SETTING 3/3 CUSTOM 1 SELECT CUSTOM SETTING EDIT/SAVE CUSTOMCUSTOM SETTING2 CUSTOM 3 CUSTOM 4 CUSTOM 5 CUSTOM 6 CUSTOM 7 CUSTOM 1 1/2 XXXXX SAVE CURRENT SETTINGS DYNAMIC RANGE FILM SIMULATION GRAIN EFFECT WHITE BALANCE HIGHLIGHT TONE SHADOW TONE COLOR AUTO OFF AUTO 0 0 0 BACK EXIT R To replace the settings in the selected bank with the settings currently selected with the camera, select K SAVE CURRENT SETTINGS and press MENU/OK. 3 A confirmation dialog will be displayed; highlight OK and press MENU/OK. SAVE CUSTOM SETTING CUSTOM 1 SET OK? OK CANCEL 82 Using a Mount Adapter Pressing the function button on the mount adapter displays l MOUNT ADAPTOR SETTING options. R Mount adapter settings can also be accessing using A SHOOTING SETTING > MOUNT ADAPTER SETTING (P 97). R Before checking focus, set the focus mode selector to M (P 63). Bright Frame Brightness Adjust the brightness of the bright frame in the OVF display. Use the BRIGHT FRAME BRIGHTNESS option to adjust the brightness of the bright frame in the OVF display. Lens Registration ■ Choosing a Focal Length If the lens has a focal length of 21, 24, 28, or 35 mm, choose a matching option in the l MOUNT ADAPTOR SETTING menu. For other lenses, select option 5 or 6 and use the selector to enter the focal length. ■ Distortion Correction Choose from STRONG, MEDIUM, or WEAK options to correct BARREL or PINCUSHION distortion. Barrel distortion LENS REGISTRATION LENS 1 LENS 2 LENS 3 LENS 4 LENS 5 LENS 6 SET LENS 5 INPUT FOCAL LENGTH SET CANCEL LENS5 DISTORTION CORRECTION BARREL STRONG BARREL MEDIUM BARREL WEAK OFF PINCUSHION WEAK PINCUSHION MEDIUM PINCUSHION STRONG More on Photography and Playback When M-mount lenses are attached using an optional FUJIFILM M MOUNT ADAPTER, the camera processes pictures as they are taken to maintain image quality and correct for a variety of effects. Pincushion distortion R To determine the amount required, adjust distortion correction while taking photos of graph paper or other objects featuring repeating vertical and horizontal lines, such as the windows in a high-rise. 83 Using a Mount Adapter ■ Color Shading Correction Color (shading) variations between the center and edges of the frame can be adjusted separately for each corner. NEXT SET To use color shading correction, follow the steps below. 1 Rotate the rear command dial to choose a corner. The selected corner is indicated by a triangle. 2 Use the selector to adjust shading until there is no visible difference in color between the selected corner and the center of the image. Press the selector left or right to adjust colors on the cyan–red axis, up or down to adjust colors on the blue–yellow axis. R To determine the amount required, adjust color shading correction while taking photos of blue sky or a sheet of gray paper. 84 ■ Peripheral Illumination Correction Choose from values between –5 and +5. Choosing positive values increases peripheral illumination, while choosing negative values reduces peripheral illumination. Positive values are recommended for vintage lenses, negative values to create the effect of images taken with an antique lens or a pinhole camera. SET CANCEL R To determine the amount required, adjust peripheral illumination correction while taking photos of blue sky or a sheet of gray paper. PhotoBook Assist Creating a PhotoBook 1 Select NEW BOOK for C PLAY BACK MENU > PHOTOBOOK ASSIST (P 101). 2 Scroll through the images and press the selector up to select or deselect. To display the current image on the cover, press the selector down. Press MENU/OK to exit when the book is complete. R Neither photographs a or smaller nor movies can be selected for photobooks. R The first picture selected becomes the cover image. Press the selector down to select a different image for the cover. 3 Highlight COMPLETE PHOTOBOOK and press MENU/OK (to select all photos or all photos matching the specified search conditions for the book, choose SELECT ALL). The new book will be added to the list in the photobook assist menu. Q Books can contain up to 300 pictures. Q Books that contain no photos are automatically deleted. More on Photography and Playback Create books from your favorite photos. 85 PhotoBook Assist Viewing Photobooks Highlight a book in the photobook assist menu and press MENU/OK to display the book, then press the selector left or right to scroll through the pictures. Editing and Deleting Photobooks Display the photobook and press MENU/OK. The following options will be displayed; select the desired option and follow the on-screen instructions. • EDIT: Edit the book as described in “Creating a PhotoBook” (P 85). • ERASE: Delete the book. Photobooks Photobooks can be copied to a computer using MyFinePix Studio software (P 123). 86 Menus Using the Menus: Shooting Mode The shooting menu is used to adjust settings for a wide range of shooting conditions. Frequently-used options can be saved to a personalized custom menu (“my menu”). Using the Shooting Menu 1 Press MENU/OK in shooting mode to display the menus. 4 Press the selector right to place the cursor in the menu. IMAGE QUALITY SETTING IMAGE SIZE IMAGE QUALITY RAW RECORDING FILM SIMULATION GRAIN EFFECT DYNAMIC RANGE WHITE BALANCE HIGHLIGHT TONE 5 Press the selector up or down to highlight the desired item. EXIT the tab for the current menu. IMAGE QUALITY SETTING IMAGE SIZE IMAGE QUALITY RAW RECORDING FILM SIMULATION GRAIN EFFECT DYNAMIC RANGE WHITE BALANCE HIGHLIGHT TONE tions for the highlighted item. Menus 6 Press the selector right to view op2 Press the selector left to highlight 7 Press the selector up or down to highlight the desired option. EXIT Tab 3 Press the selector down to highlight the tab (H, G, A, F, B, or E) containing the desired item. 8 Press MENU/OK to select the highlighted option. 9 Press DISP/BACK to return to the shooting display. R Use the front command dial to scroll through the menus a page at a time. 87 Using the Menus: Shooting Mode H IMAGE QUALITY SETTING To adjust shooting settings that affect image quality, press MENU/OK in the shooting display and select the H (IMAGE QUALITY SETTING) tab (P 87). IMAGE QUALITY SETTING IMAGE SIZE IMAGE QUALITY RAW RECORDING FILM SIMULATION GRAIN EFFECT DYNAMIC RANGE WHITE BALANCE HIGHLIGHT TONE EXIT IMAGE SIZE Choose the size and aspect ratio at which still pictures are recorded. Option O3:2 O 16 : 9 O1:1 P3:2 P 16 : 9 IMAGE SIZE is not reset when the camera is turned off or another P 1 : 1 shooting mode is selected. Aspect Ratio Pictures with an aspect ratio of 3 : 2 have the same proportions as a frame of 35 mm film, while an aspect ratio of 16 : 9 is suited to display on High Definition (HD) devices. Pictures with an aspect ratio of 1 : 1 are square. Image size 6000 × 4000 6000 × 3376 4000 × 4000 4240 × 2832 4240 × 2384 2832 × 2832 Option Q3:2 Q 16 : 9 Q1:1 Image size 3008 × 2000 3008 × 1688 2000 × 2000 IMAGE QUALITY Choose a file format and compression ratio. Select FINE or NORMAL to record JPEG images, RAW to record RAW images, or FINE+RAW or NORMAL+RAW to record both JPEG and RAW images. FINE and FINE+RAW use lower JPEG compression ratios for higher-quality JPEG images, while NORMAL and NORMAL+RAW use higher JPEG compression ratios to increase the number of images that can be stored. RAW RECORDING Choose whether to compress RAW images. Option UNCOMPRESSED Description RAW images are not compressed. RAW images are compressed using a reversible algorithm that reduces file size with no loss of image data. LOSSLESS COMPRESSED The images can be viewed in RAW FILE CONVERTER (P 123) or other compatible software. 88 Using the Menus: Shooting Mode FILM SIMULATION Simulate the effects of different types of film (P 60). GRAIN EFFECT Add a film grain effect. DYNAMIC RANGE Control contrast. Choose lower values to increase contrast when shooting indoors or under overcast skies, higher values to reduce loss of detail in highlights and shadows when photographing high-contrast scenes. Higher values are recommended for scenes that include both sunlight and deep shade, for such high-contrast subjects as sunlight on water, brightly-lit autumn leaves, and portraits taken against a blue sky, and for white objects or people wearing white; note, however, that mottling may appear in pictures taken at higher values. R If AUTO is selected, the camera will automatically choose either V 100% or W 200% according to the subject and shooting conditions. Shutter speed and aperture will be displayed when the shutter button is pressed halfway. R W 200% is available at sensitivities of ISO 400 and above, X 400% at sensitivities of ISO 800 and above. HIGHLIGHT TONE Adjust the appearance of highlights. Menus WHITE BALANCE Adjust colors to match the light source (P 61). SHADOW TONE Adjust the appearance of shadows. COLOR Adjust color density. SHARPNESS Sharpen or soften outlines. NOISE REDUCTION Reduce noise in pictures taken at high sensitivities. 89 Using the Menus: Shooting Mode LONG EXPOSURE NR Select ON to reduce mottling in long time-exposures (P 71). LENS MODULATION OPTIMIZER Select ON to improve definition by adjusting for diffraction and the slight loss of focus at the periphery of the lens. COLOR SPACE Choose the gamut of colors available for color reproduction. Option sRGB Adobe RGB Description Recommended in most situations. For commercial printing. PIXEL MAPPING Use this option if you notice bright spots in your pictures. 1 Press MENU/OK in the shooting display and select the H IMAGE QUALITY SETTING tab (P 87). 2 Highlight PIXEL MAPPING and press MENU/OK to perform pixel mapping. Q Q Q Q Results are not guaranteed. Be sure the battery is fully charged before beginning pixel mapping. Pixel mapping is not available when the camera temperature is elevated. Processing may take a few seconds. SELECT CUSTOM SETTING Recall settings saved with EDIT/SAVE CUSTOM SETTING. EDIT/SAVE CUSTOM SETTING Save settings (P 82). 90 Using the Menus: Shooting Mode G AF/MF SETTING To adjust focus settings, press MENU/OK in the shooting display and select the G (AF/MF SETTING) tab (P 87). AF/MF SETTING FOCUS AREA AF MODE NUMBER OF THE FOCUS POINTS PRE-AF AF ILLUMINATOR FACE/EYE DETECTION SETTING AF+MF MF ASSIST EXIT FOCUS AREA Choose the focus area (P 68). Focus-area selection can also be used to choose the focus point for manual focus and focus zoom. AF MODE Choose the AF mode for focus modes S and C (P 66). Option 77 POINTS (7 × 11) 273 POINTS (13 × 21) Description Choose from 77 focus points arranged in a 7- by 11-point grid. Choose from 273 focus points arranged in a 13- by 21-point grid. Menus NUMBER OF THE FOCUS POINTS Choose the number of focus points available for focus-point selection in manual focus mode or when SINGLE POINT is selected for AF MODE. PRE-AF If ON is selected, the camera will continue to adjust focus even when the shutter-release button is not pressed halfway. Note that this increases the drain on the battery. AF ILLUMINATOR If ON is selected, the AF-assist illuminator will light to assist autofocus. Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the camera is unable to focus in macro mode, try increasing the distance to the subject. Q Avoid shining the AF-assist illuminator directly into your subject’s eyes. 91 Using the Menus: Shooting Mode FACE/EYE DETECTION SETTING Intelligent Face Detection sets focus and exposure for human faces anywhere in the frame, preventing the camera from focusing on the background in group portraits. Choose for shots that emphasize portrait subjects. Faces can be detected with the camera in vertical or horizontal orientation; if a face is detected, it will be indicated by a green border. If there is more than one face in the frame, the camera will select the face closest to the center; other faces are indicated by white borders. You can also choose whether the camera detects and focuses on eyes when Intelligent Face Detection is on. Choose from the following options: Option FACE ON/EYE OFF FACE ON/EYE AUTO FACE ON/RIGHT EYE PRIORITY FACE ON/LEFT EYE PRIORITY FACE OFF/EYE OFF Description Intelligent Face Detection only. The camera automatically chooses which eye to focus on when a face is detected. The camera focuses on the right eye of subjects detected using Intelligent Face Detection. The camera focuses on the left eye of subjects detected using Intelligent Face Detection. Intelligent Face Detection and eye priority off. R If the camera is unable to detect the subject’s eyes because they are hidden by hair, glasses, or other objects, the camera will instead focus on faces. Q In some modes, the camera may set exposure for the frame as a whole rather than the portrait subject. Q If the subject moves as the shutter button is pressed, the face may not be in the area indicated by the green border when the picture is taken. 92 Using the Menus: Shooting Mode AF+MF If ON is selected in focus mode S, focus can be adjusted manually by rotating the focus ring while the shutter button is pressed halfway. Both standard and focus peaking MF assist options are supported. Lenses with a focus distance indicator must be set to manual focus mode (MF) before this option can be used. Selecting MF disables the focus distance indicator. Set the focus ring to the center of the focus distance indicator, as the camera may fail to focus if the ring is set to infinity or the minimum focus distance. AF + MF Focus Zoom When ON is selected for G AF/MF SETTING > SETTING > FOCUS CHECK and SINGLE POINT selected for AF MODE, MODE, focus zoom can be used to zoom in on the selected focus area. Focus zoom is not available when ZONE or WIDE/TRACKING is selected for AF MODE.. The zoom ratio (2.5× — 6×) can be selected using the rear command dial. MODE MF ASSIST Choose how focus is displayed in manual focus mode (P 65). Menus Option Description STANDARD Focus is displayed normally (focus peaking and digital split image are not available). DIGITAL SPLIT IMAGE A black-and-white (MONOCHROME) or color (COLOR) split-image display. FOCUS PEAK HIGHLIGHT The camera heightens high-contrast outlines. Choose a color and peaking level. FOCUS CHECK If ON is selected, the camera will automatically zoom in on the view through the lens when the focus ring is rotated in manual focus mode (P 64). INTERLOCK SPOT AE & FOCUS AREA Select ON to meter the current focus frame when SINGLE POINT is selected for AF MODE (P 66) and SPOT is selected for PHOTOMETRY (P 59). INSTANT AF SETTING Choose how the camera focuses when the AF-L button is pressed in manual focus mode (P 63). 93 Using the Menus: Shooting Mode DEPTH-OF-FIELD SCALE Choose FILM FORMAT BASIS to help you make practical assessments of depth of field for pictures that will be viewed as prints and the like, PIXEL BASIS to help you assess depth of field for pictures that will be viewed at high resolutions on computers or other electronic displays. RELEASE/FOCUS PRIORITY Choose how the camera focuses in focus mode AF-S or AF-C. Option RELEASE FOCUS Description Shutter response is prioritized over focus. Pictures can be taken when the camera is not in focus. Focus is prioritized over shutter response. Pictures can be only taken when the camera is in focus. CORRECTED AF FRAME If ON is selected, a second focus frame for focus distances of about 50 cm (1.6 ft) will be added to the display in the optical viewfinder. The focus frame for the current focus distance is displayed in green when the shutter button is pressed halfway. ON OFF Focus frame for focus distance of infinity Focus frame Focus frame for focus distance of about 50 cm (1.6 ft) 94 Using the Menus: Shooting Mode A SHOOTING SETTING To adjust shooting options, press MENU/OK in the shooting display and select the A (SHOOTING SETTING) tab (P 87). SHOOTING SETTING SELF-TIMER INTERVAL TIMER SHOOTING FILM SIMULATION BKT PHOTOMETRY SHUTTER TYPE IS MODE ISO AUTO SETTING MOUNT ADAPTOR SETTING EXIT SELF-TIMER Take pictures with the self-timer (P 73). INTERVAL TIMER SHOOTING Adjust settings for interval timer photography (P 74). FILM SIMULATION BKT Choose film types for film simulation bracketing (P 54, 60). Menus PHOTOMETRY Choose how the camera meters exposure (P 59). 95 Using the Menus: Shooting Mode SHUTTER TYPE Choose the shutter type. Choose the electronic shutter to mute the shutter sound. Option Description Take pictures with the mechanical shutter. t MECHANICAL SHUTTER Take pictures with the electronic shutter. s ELECTRONIC SHUTTER t MECHANICAL + s ELECTRONIC The camera chooses the shutter type according to shooting conditions. R If s ELECTRONIC SHUTTER or t MECHANICAL + s ELECTRONIC is selected, shutter speeds faster than 1/8,000 s can be chosen by rotating the shutter speed dial to 8000 and then rotating the front command dial. R When the electronic shutter is used, shutter speed and sensitivity are restricted to values of 1/32,000–1 s and ISO 12800–200 respectively, and long exposure noise reduction has no effect. In burst mode, focus and exposure are fixed at the values for the first shot in each burst. Q Distortion may be visible in shots of moving subjects with electronic shutter, while banding and fog may occur in shots taken under fluorescent lights or other flickering or erratic illumination. When taking pictures with the shutter muted, respect your subjects’ image rights and right to privacy. IS MODE Reduce blur. This option is available only with lenses that support image stabilization. Option l CONTINUOUS m SHOOTING ONLY OFF 96 Description Image stabilization on. Image stabilization enabled only when the shutter button is pressed halfway or the shutter is released. Image stabilization off ; x appears in the display (P 8, 10). Recommended when using a tripod. Using the Menus: Shooting Mode ISO AUTO SETTING Choose the base sensitivity, maximum sensitivity, and minimum shutter speed for auto ISO sensitivity control, which is selected by rotating the ISO dial to A. Settings for AUTO1, AUTO2, and AUTO3 can be adjusted separately. Option DEFAULT SENSITIVITY MAX. SENSITIVITY MIN. SHUTTER SPEED Default 200 800 (AUTO1)/1600 (AUTO2)/3200 (AUTO3) 1/60 The camera automatically chooses a sensitivity between the default and maximum values. Sensitivity is only raised above the default value if the shutter speed required for optimal exposure would be slower than the value selected for MIN. SHUTTER SPEED. MOUNT ADAPTOR SETTING Adjust settings for M-mount lenses connected using an optional FUJIFILM M MOUNT ADAPTER (P 83). Menus R If the value selected for DEFAULT SENSITIVITY is higher than that selected for MAX. SENSITIVITY, DEFAULT SENSITIVITY will be set to the value selected for MAX. SENSITIVITY. R The camera may select shutter speeds slower than MIN. SHUTTER SPEED if pictures would still be underexposed at the value selected for MAX. SENSITIVITY. WIRELESS COMMUNICATION Connect to a smartphone or tablet over a wireless network (P 122). R For more information, visit http://fujifilm-dsc.com/wifi/. 97 Using the Menus: Shooting Mode F FLASH SETTING To adjust flash-related settings, press MENU/OK in the shooting display and select the F (FLASH SETTING) tab (P 87). FLASH SETTING FLASH MODE FLASH COMPENSATION RED EYE REMOVAL EXIT FLASH MODE Choose a flash mode (P 78). FLASH COMPENSATION Adjust flash brightness. Note that the desired results may not be achieved depending on shooting conditions and the distance to the subject. RED EYE REMOVAL Choose ON to remove red-eye effects caused by the flash. R Red-eye reduction is performed only when a face is detected. R Red-eye removal is not available with RAW images. 98 Using the Menus: Shooting Mode B MOVIE SETTING To adjust options for movie recording, press MENU/OK in the shooting display and select the B (MOVIE SETTING) tab (P 87). MOVIE SETTING MOVIE MODE MIC LEVEL ADJUSTMENT MIC/REMOTE RELEASE EXIT MOVIE MODE Select a frame size and rate for movie recording. • i 1080/60 P: 1920 × 1080 (60 fps) • i 1080/50 P: 1920 × 1080 (50 fps) • i 1080/30 P: 1920 × 1080 (30 fps) • i 1080/25 P: 1920 × 1080 (25 fps) • i 1080/24 P: 1920 × 1080 (24 fps) • • • • • h 720/60 P: 1280 × 720 (60 fps) h 720/50 P: 1280 × 720 (50 fps) h 720/30 P: 1280 × 720 (30 fps) h 720/25 P: 1280 × 720 (25 fps) h 720/24 P: 1280 × 720 (24 fps) MIC/REMOTE RELEASE Specify whether the device connected to the microphone/remote release connector is a microphone or a remote release (P 45, 72). Menus MIC LEVEL ADJUSTMENT Adjust the microphone recording level. 99 Using the Menus: Shooting Mode E MY MENU To display a personalized menu of frequently-used options, press MENU/OK in the shooting display and select the E (MY MENU) tab (P 87). R To edit “my menu”, select D USER SETTING > MY MENU SETTING (P 118). R The E tab is only available if options have been assigned to MY MENU. MY MENU SELF-TIMER INTERVAL TIMER SHOOTING FILM SIMULATION BKT PHOTOMETRY SHUTTER TYPE IS MODE FACE/EYE DETECTION SETTING ISO AUTO SETTING EXIT 100 Using the Menus: Playback Mode The playback menu is used to adjust playback settings. Using the Playback Menu 1 Press MENU/OK in playback mode to display the menus. 4 Press the selector up or down to highlight the desired option. PLAY BACK MENU SWITCH SLOT RAW CONVERSION ERASE CROP RESIZE PROTECT IMAGE ROTATE RED EYE REMOVA 5 Press MENU/OK to select the highlighted option. EXIT 2 Press the selector up or down to highlight the desired item. back display. R Use the front command dial to scroll through the menus a page at a time. Menus 3 Press the selector right to view op- 6 Press DISP/BACK to return to the play- tions for the highlighted item. 101 Using the Menus: Playback Mode C PLAY BACK MENU To access playback options, press MENU/OK in the playback display and select the C (PLAY BACK MENU) tab (P 101). PLAY BACK MENU SWITCH SLOT RAW CONVERSION ERASE CROP RESIZE PROTECT IMAGE ROTATE RED EYE REMOVA EXIT SWITCH SLOT Choose the card from which images will be played back (P 39). RAW CONVERSION Create JPEG copies of RAW pictures (P 81). ERASE Delete pictures (P 43). CROP Create a cropped copy of the current picture. 1 Display the desired picture. 2 Select C CROP in the playback menu. 3 Use the rear command dial to zoom in and out and press the selector up, down, left, or right to scroll the picture until the desired portion is displayed. 4 Press MENU/OK to display a confirmation dialog. 5 Press MENU/OK again to save the cropped copy to a separate file. R Larger crops produce larger copies; all copies have an aspect ratio of 3 : 2. If the size of the final copy will be a, OK will be displayed in yellow. 102 Using the Menus: Playback Mode RESIZE Create a small copy of the current picture. 1 Display the desired picture. 2 Select C RESIZE in the playback menu. 3 Highlight a size and press MENU/OK to display a confirmation dialog. 4 Press MENU/OK again to save the resized copy to a separate file. R The sizes available vary with the size of the original image. Q Protected pictures will be deleted when the memory card is formatted (P 107). IMAGE ROTATE Rotate pictures. Menus PROTECT Protect pictures from accidental deletion. Highlight one of the following options and press MENU/OK. • FRAME: Protect selected pictures. Press the selector left or right to view pictures and press MENU/OK to select or deselect. Press DISP/BACK when the operation is complete. • SET ALL: Protect all pictures. • RESET ALL: Remove protection from all pictures. 1 Display the desired picture. 2 Select C IMAGE ROTATE in the playback menu. 3 Press the selector down to rotate the picture 90° clockwise, up to rotate it 90° counterclockwise. 4 Press MENU/OK. The picture will automatically be displayed in the selected orientation whenever it is played back on the camera. R Protected pictures can not be rotated. Remove protection before rotating pictures. R The camera may not be able to rotate pictures created with other devices. Pictures rotated on the camera will not be rotated when viewed on a computer or on other cameras. R Pictures taken with D SCREEN SETTING > AUTOROTATE PB are automatically displayed in the correct orientation during playback (P 111). 103 Using the Menus: Playback Mode RED EYE REMOVAL Remove red-eye from portraits. The camera will analyze the image; if red-eye is detected, the image will be processed to create a copy with reduced red-eye. 1 Display the desired picture. 2 Select C RED EYE REMOVAL in the playback menu. 3 Press MENU/OK. R Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ depending on the scene. Red eye can not be removed from pictures that have already been processed using red-eye removal or pictures created with other devices. R The amount of time needed to process the image varies with the number of faces detected. R Copies created with RED EYE REMOVAL are indicated by a e icon during playback. R Red eye removal can not be performed on RAW images. COPY Copy pictures between the cards in the first and second slots. 1 Select C COPY in the playback menu. 2 Highlight one of the following options and press the selector right: • SLOT1 y SLOT2: Copy pictures from the card in the first slot to the card in the second slot. • SLOT2 y SLOT1: Copy pictures from the card in the second slot to the card in the first slot. 3 Highlight one of the following options and press MENU/OK: • FRAME: Copy selected pictures. Press the selector left or right to view pictures and press MENU/OK to copy the current picture. • ALL FRAMES: Copy all pictures. R Copying ends when the destination is full. WIRELESS COMMUNICATION Connect to a smartphone or tablet over a wireless network (P 122). R For more information, visit http://fujifilm-dsc.com/wifi/. 104 Using the Menus: Playback Mode SLIDE SHOW View pictures in an automated slide show. Press MENU/OK to start. Press DISP/BACK at any time during the show to view on-screen help. The show can be ended at any time by pressing MENU/OK. R The camera will not turn off automatically while a slide show is in progress. PHOTOBOOK ASSIST Create books from your favorite photos (P 85). PC AUTO SAVE Upload pictures to a computer over a wireless network (P 122). R For more information, visit http://fujifilm-dsc.com/wifi/. PRINT ORDER (DPOF) Select pictures for printing (P 126). DISP ASPECT Choose how High Definition (HD) devices display pictures with an aspect ratio of 3 : 2 (this option is available only when an HDMI cable is connected). Select 16 : 9 to display the image so that it fills the screen with its top and bottom cropped out, 3 : 2 to display the entire image with black bands at either side. Menus instax PRINTER PRINT Print pictures on optional FUJIFILM instax SHARE printers (P 129). 16 : 9 3:2 16 : 9 3:2 105 The Setup Menu View and adjust basic camera settings. Using the Setup Menu 1 Press MENU/OK in shooting mode to display the menus. IMAGE QUALITY SETTING IMAGE SIZE IMAGE QUALITY RAW RECORDING FILM SIMULATION GRAIN EFFECT DYNAMIC RANGE WHITE BALANCE HIGHLIGHT TONE 5 Press the selector up or down to highlight the category containing the desired item. 6 Press the selector right to view the option in the highlighted category. EXIT 2 Press the selector left to highlight the tab for the current menu. 7 Press the selector up or down to highlight the desired item. SET UP USER SETTING SOUND SETTING SCREEN SETTING BUTTON/DIAL SETTING POWER MANAGEMENT SAVE DATA SETTING CONNECTION SETTING 8 Press the selector right to view options for the highlighted item. EXIT Tab 9 Press the selector up or down to highlight the desired option. 3 Press the selector down to highlight the D (SET UP) tab. 10 Press MENU/OK to select the highlighted option. 4 Press the selector right to display setup menu categories. 106 11 Press DISP/BACK to return to the shooting display. R Use the front command dial to scroll through the menus a page at a time. The Setup Menu D SET UP Menu Options To access basic camera settings, press MENU/OK in the playback display and select the D (SET UP) tab (P 106). SET UP USER SETTING SOUND SETTING SCREEN SETTING BUTTON/DIAL SETTING POWER MANAGEMENT SAVE DATA SETTING CONNECTION SETTING EXIT ■ D USER SETTING FORMAT To format a memory card: MENU/OK. To exit without formatting the memory card, select CANCEL or press DISP/BACK. Q All data—including protected pictures—will be deleted from the memory card. Be sure important files have been copied to a computer or other storage device. Q Do not open the battery-chamber cover during formatting. FORMAT FORMAT CARD IN SLOT 1, OK? ERASE ALL DATA Menus 1 Highlight D USER SETTING > FORMAT in the setup menu and press MENU/OK. 2 Highlight the slot containing the card you wish to format and press MENU/OK. 3 A confirmation dialog will be displayed. To format the memory card, highlight OK and press OK CANCEL R The format menu can also be displayed by pressing the center of the rear command dial while pressing and holding the b button. DATE/TIME Set the camera clock (P 26, 27). 107 The Setup Menu TIME DIFFERENCE Switch the camera clock instantly from your home time zone to the local time at your destination when traveling. To specify the difference between local time and your home time zone: 1 Highlight g LOCAL and press MENU/OK. 2 Use the selector to choose the time difference between local time and your home time zone. Press MENU/OK when settings are complete. To set the camera clock to local time, highlight g LOCAL and press MENU/OK. To set the clock to the time in your home time zone, select h HOME. If g LOCAL is selected, g will be displayed for three seconds when the camera is turned on. a Choose a language. MY MENU SETTING Edit “my menu” (P 118). SENSOR CLEANING Remove dust from the camera image sensor. • OK: Clean sensor immediately (P xi). • WHEN SWITCHED ON: If this option is selected, sensor cleaning will be performed when the camera turns on. • WHEN SWITCHED OFF: If this option is selected, sensor cleaning will be performed when the camera turns off (sensor cleaning is not however performed if the camera turns off in playback mode). R Dust that can not be removed using sensor cleaning can be removed manually (P 136). RESET Reset shooting or setup menu options to default values. Custom white balance, custom settings banks created using EDIT/ SAVE CUSTOM SETTING, WIRELESS SETTINGS, and the setup menu DATE/TIME, TIME DIFFERENCE options are not affected. 1 Highlight the desired option and press the selector right. 2 A confirmation dialog will be displayed; highlight OK and press MENU/OK. 108 The Setup Menu ■ D SOUND SETTING AF BEEP VOL. Choose the volume of the beep that sounds when the camera focuses (P 75). The beep can be muted by selecting OFF. SELF-TIMER BEEP VOL. Choose the volume of the beep that sounds while the self-timer is active (P 73). The beep can be muted by selecting OFF. OPERATION VOL. Adjust the volume of the sounds produced when camera controls are operated. Choose e OFF (mute) to disable control sounds. SHUTTER VOLUME Adjust the volume of the sounds produced when the shutter is released. Choose e OFF (mute) to disable the shutter sound. SHUTTER SOUND Choose the sound made by the shutter. Menus PLAYBACK VOLUME Adjust the volume for movie playback. 109 The Setup Menu ■ D SCREEN SETTING EVF BRIGHTNESS Adjust the brightness of the display in the electronic viewfinder, or choose AUTO for automatic brightness adjustment. EVF COLOR Adjust the hue of the display in the electronic viewfinder. LCD BRIGHTNESS Adjust monitor brightness. LCD COLOR Adjust monitor hue. IMAGE DISP. Choose how long images are displayed after shooting. Colors may differ slightly from those in the final image and “noise” mottling may be visible at high sensitivities. Option CONTINUOUS 1.5 SEC 0.5 SEC OFF Description Pictures are displayed until the MENU/OK button is pressed or the shutter button is pressed halfway. To zoom in on the active focus point, press the center of the rear command dial; press again to cancel zoom. Pictures are displayed for 1.5 seconds (1.5 SEC) or 0.5 seconds (0.5 SEC) or until the shutter button is pressed halfway. Pictures are not displayed after shooting. EVF AUTOROTATE DISPLAYS Choose whether the indicators in the viewfinder rotate to match camera orientation (P 31). Regardless of the option selected, the indicators in the monitor do not rotate. PREVIEW EXP./WB IN MANUAL MODE Select PREVIEW EXP./WB to enable exposure and white balance preview in manual exposure mode (P 38), or choose PREVIEW WB to preview only white balance. Select OFF when using a flash or on other occasions on which exposure may change when the picture is taken. 110 The Setup Menu PREVIEW PIC. EFFECT Choose ON to preview the effects of film simulation, white balance, and other settings in the monitor. Choose OFF to make shadows in low-contrast, back-lit scenes and other hard-to-see subjects more visible. R If OFF is selected, the effects of camera settings will not be visible in the monitor and colors and tone will differ from those in the final picture. The display will however be adjusted to show the effects of advanced filters and of monochrome and sepia settings. FRAMING GUIDELINE Choose the type of framing grid available in shooting mode. F GRID 9 H HD FRAMING A six-by-four grid. Frame HD pictures in the crop shown by the lines at the top and bottom of the display. P P Menus P For “rule of thirds” composition. G GRID 24 AUTOROTATE PB Choose ON to automatically rotate “tall” (portrait-orientation) pictures during playback. FOCUS SCALE UNITS Choose the units used for the focus distance indicator (P 64). DISP. CUSTOM SETTING Choose items for the standard display (P 33). 111 The Setup Menu ■ D BUTTON/DIAL SETTING FOCUS LEVER SETTING Choose the functions performed by the focus stick (focus lever). Option LOCK (OFF) PUSH n TO UNLOCK ON Description The focus stick can not be used during shooting. Press the stick to view the focus-point display and tilt the stick to select a focus point. Tilt the stick to view the focus-point display and select a focus point. EDIT/SAVE QUICK MENU Choose the options displayed in the quick menu (P 49). FUNCTION (Fn) SETTING Choose the roles played by the function buttons (P 51). COMMAND DIAL SETTING Choose the roles played by the command dials. ISO DIAL SETTING (H) Choose the ISO sensitivity assigned to the H position on the ISO dial. SHOOT WITHOUT LENS Choose whether shutter release is enabled when no lens is attached. FOCUS RING Choose the direction in which the focus ring is rotated to increase the focus distance. 112 The Setup Menu AE-L/AF-L BUTTON SETTING Switch the roles of the AF-L and AE-L buttons. AE/AF-LOCK MODE If AE & AF ON WHEN PRESSING is selected, exposure and/or focus will lock while the AE-L or AF-L button is pressed (P 76). If AE & AF ON/OFF SWITCH is selected, exposure and/or focus will lock when the AE-L or AF-L button is pressed and remain locked until the button is pressed again. AF-LOCK MODE Choose the role played by the AF-L button (P 76). Menus APERTURE SETTING Choose the method used to adjust aperture when using lenses with no aperture rings. • AUTO + o MANUAL: Rotate the rear command dial to choose the aperture. Rotate past minimum aperture to choose A (auto). • AUTO: Aperture is selected automatically; camera functions in exposure mode P (program AE) or S (shutter-priority AE). • MANUAL: Rotate the rear command dial to choose the aperture; camera functions in exposure mode A (aperture-priority AE) or M (manual). 113 The Setup Menu ■ D POWER MANAGEMENT AUTO POWER OFF Choose the length of time before the camera turns off automatically when no operations are performed. Shorter times increase battery life; if OFF is selected, the camera must be turned off manually. Note that in some situations the camera turns off automatically even when OFF is selected. POWER MANAGEMENT Adjust power management settings. Option HIGH PERFORMANCE STANDARD ECONOMY AF performance (speed) Fast Fast Normal LCD/EVF display quality Very high High Normal Battery endurance Low Normal High R When ECONOMY is selected, the frame rate will drop when no operations are being performed. Operating camera controls returns the frame rate to normal. 114 The Setup Menu ■ D SAVE DATA SETTING FRAME NO. New pictures are stored in image files named using a four-digit file number assigned by adding one to the Frame number last file number used. The file number is displayed during playback as shown at right. FRAME NO. controls 100-0001 whether file numbering is reset to 0001 when a new memory card is inserted or the current memory card is formatted. Directory File number number Option Description Numbering continues from the last file number used or the first available file number, whichever is higher. Choose CONTINUOUS this option to reduce the number of pictures with duplicate file names. RENEW Numbering is reset to 0001 after formatting or when a new memory card is inserted. SAVE ORG IMAGE Choose ON to save unprocessed copies of pictures taken using F FLASH SETTING > RED EYE REMOVAL (P 98). Menus R If the frame number reaches 999-9999, the shutter release will be disabled (P 143). R Selecting D USER SETTING > RESET (P 108) sets FRAME NO. to CONTINUOUS but does not reset the file number. R Frame numbers for pictures taken with other cameras may differ. EDIT FILE NAME Change the file name prefix. sRGB images use a four-letter prefix (default “DSCF”), Adobe RGB images a three-letter prefix (“DSF”) preceded by an underscore. 115 The Setup Menu CARD SLOT SETTING (STILL IMAGE) Choose the role played by the card in the second slot. Option Description SEQUENTIAL The card in the second slot is used only when the card in the first slot is full. BACKUP Each picture is recorded twice, once to each card. As for SEQUENTIAL, except that the RAW copy of pictures taken with FINE + RAW or NORMAL + RAW selected RAW / JPEG for H IMAGE QUALITY SETTING > IMAGE QUALITY will be saved to the card in the first slot and the JPEG copy to the card in the second slot. R Regardless of the option selected for CARD SLOT SETTING (STILL IMAGE), movies will be recorded to the card in the first slot; if SEQUENTIAL is selected, movies will be recorded to the card in the first slot even after recording has moved on to the card in the second slot. SWITCH SLOT (SEQUENTIAL) Choose the card that is recorded to first when SEQUENTIAL is selected for CARD SLOT SETTING (STILL IMAGE). 116 The Setup Menu ■ D CONNECTION SETTING For more information on wireless connections, visit http://fujifilm-dsc.com/wifi/ WIRELESS SETTINGS Adjust settings for connection to wireless networks. Option GENERAL SETTINGS RESIZE IMAGE FOR SMARTPHONE H PC AUTO SAVE SETTINGS PC AUTO SAVE SETTING Choose an upload destination. Choose SIMPLE SETUP to connect using WPS, MANUAL SETUP to configure network settings manually. Menus Description Choose a name (NAME) to identify the camera on the wireless network (the camera is assigned a unique name by default) or select RESET WIRELESS SETTINGS to restore default settings. Choose ON (the default setting, recommended in most circumstances) to resize larger images to H for upload to smartphones, OFF to upload images at their original size. Resizing applies only to the copy uploaded to the smartphone; the original is not affected. Choose DELETE REGISTERED DESTINATION PC to remove selected destinations, DETAILS OF PREVIOUS CONNECTION to view computers to which the camera has recently connected. GEOTAGGING SET-UP View location data downloaded from a smartphone and choose whether to save the data with your pictures. Option GEOTAGGING LOCATION INFO Description Choose whether location data downloaded from a smartphone are embedded in pictures as they are taken. Display the location data last downloaded from a smartphone. instax PRINTER CONNECTION SETTING Adjust settings for connection to optional FUJIFILM instax SHARE printers (P 128). 117 “My Menu” Selecting the E (MY MENU) tab displays a personalized custom menu of frequently-used options (P 100). Editing “My Menu” 1 In the setup menu D USER SETTING tab, highlight MY MENU SETTING and press MENU/OK to display the following options (P 106). 3 Highlight an item and press MENU/OK to add it to “my menu”. MY MENU SETTING 1 IMAGE SIZE MY MENU SETTING MY MENU SETTING RANK ITEMS REMOVE ITEMS MOVE SAVE 4 Press MENU/OK to return to the edit display. 2 Press the selector up or down to highlight MY MENU SETTING and press MENU/OK. Options that can be added to “my menu” are highlighted in blue. R Options currently in “my menu” are indicated by check marks. MY MENU SETTING IMAGE SIZE IMAGE QUALITY RAW RECORDING FILM SIMULATION GRAIN EFFECT DYNAMIC RANGE WHITE BALANCE HIGHLIGHT TONE SELECT 118 CANCEL 5 Repeat Steps 3 and 4 until all the desired items have been added. R “My menu” can contain up to 16 items. Editing “My Menu” To reorder or delete items, select RANK ITEMS or REMOVE ITEMS in Step 1. Factory Defaults The factory default settings for the options in the shooting and setup menus are listed below. These settings can be restored using D USER SETTING > RESET (P 108). ■ Shooting Menu Menu Default O3:2 FINE UNCOMPRESSED PROVIA/STANDARD OFF 100% AUTO 0 0 0 0 0 ON ON sRGB CUSTOM 1 Default Menu G AF/MF SETTING AF MODE NUMBER OF THE FOCUS POINTS PRE-AF AF ILLUMINATOR FACE/EYE DETECTION SETTING AF+MF MF ASSIST FOCUS CHECK INTERLOCK SPOT AE & FOCUS AREA INSTANT AF SETTING RELEASE/FOCUS PRIORITY • AF-S PRIORITY SELECTION • AF-C PRIORITY SELECTION CORRECTED AF FRAME SINGLE POINT 77 POINTS (7×11) OFF ON FACE OFF/EYE OFF OFF STANDARD OFF ON Menus H IMAGE QUALITY SETTING IMAGE SIZE IMAGE QUALITY RAW RECORDING FILM SIMULATION GRAIN EFFECT DYNAMIC RANGE WHITE BALANCE HIGHLIGHT TONE SHADOW TONE COLOR SHARPNESS NOISE REDUCTION LONG EXPOSURE NR LENS MODULATION OPTIMIZER COLOR SPACE SELECT CUSTOM SETTING AF-S RELEASE RELEASE OFF 119 Factory Defaults Default Menu G SHOOTING SETTING SELF-TIMER FILM SIMULATION BKT • FILM 1 • FILM 2 • FILM 3 PHOTOMETRY SHUTTER TYPE IS MODE ISO AUTO SETTING MOUNT ADAPTOR SETTING • BRIGHT FRAME BRIGHTNESS • LENS REGISTRATION 120 ■ Setup Menu Default Menu OFF PROVIA/STANDARD Velvia/VIVID ASTIA/SOFT MULTI MECHANICAL SHUTTER CONTINUOUS AUTO1 0 LENS 5 (50mm) F FLASH SETTING FLASH MODE FLASH COMPENSATION RED EYE REMOVAL AUTO ±0 OFF B MOVIE SETTING MOVIE MODE MIC LEVEL ADJUSTMENT MIC/REMOTE RELEASE i 1920/60P 3 MIC D USER SETTING TIME DIFFERENCE SENSOR CLEANING • WHEN SWITCHED ON • WHEN SWITCHED OFF OFF ON D SOUND SETTING AF BEEP VOL. SELF-TIMER BEEP VOL. OPERATION VOL. SHUTTER VOLUME SHUTTER SOUND PLAYBACK VOLUME c c OFF c SOUND 1 7 D SCREEN SETTING EVF BRIGHTNESS EVF COLOR LCD BRIGHTNESS LCD COLOR IMAGE DISP. EVF AUTOROTATE DISPLAYS PREVIEW EXP./WB IN MANUAL MODE PREVIEW PIC. EFFECT FRAMING GUIDELINE AUTOROTATE PB FOCUS SCALE UNITS DISP. CUSTOM SETTING HOME AUTO 0 0 0 OFF ON PREVIEW EXP./WB ON GRID 9 OFF METERS See page 33. Factory Defaults Menu D BUTTON/DIAL SETTING FOUCS LEVER SETTING EDIT/SAVE QUICK MENU FUNCTION (Fn) SETTING COMMAND DIAL SETTING ISO DIAL SETTING SHOOT WITHOUT LENS FOCUS RING AE-L/AF-L BUTTON SETTING AE/AF-LOCK MODE D POWER MANAGEMENT AUTO POWER OFF POWER MANAGEMENT ON See page 47. See page 50. Y S.S. X F 25600 OFF X CW AE-L/AF-L AE&AF ON WHEN PRESSING AF LOCK ONLY AUTO + MANUAL 2 MIN STANDARD Default Menu D SAVE DATA SETTING FRAME NO. SAVE ORG IMAGE CARD SLOT SETTING (STILL IMAGE) D CONNECTION SETTING WIRELESS SETTINGS • RESIZE IMAGE FOR SMARTPHONE H PC AUTO SAVE SETTING GEOTAGGING SET-UP • GEOTAGGING • LOCATION INFO CONTINUOUS OFF SEQUENTIAL ON SIMPLE SETUP ON ON Menus AF-LOCK MODE APERTURE SETTING Default 121 Connections Wireless Transfer Access wireless networks and connect to computers, smartphones, or tablets. For downloads and other information, visit http://fujifilm-dsc.com/wifi/. Wireless Connections: Smartphones Install the “FUJIFILM Camera Remote” app on your smartphone to browse the images on the camera, download selected images, control the camera remotely, or copy location data to the camera. To connect to the smartphone, set the camera to playback mode and press the function button (Fn1). R You can also connect using A SHOOTING SETTING/C PLAY BACK MENU > WIRELESS COMMUNICATION (P 97, 104). 122 Wireless Connections: Computers Once you have installed the “FUJIFILM PC AutoSave” application and configured your computer as a destination for the images copied from the camera, you can upload pictures from the camera using C PLAY BACK MENU > PC AUTO SAVE (P 105) or by pressing and holding the function button (Fn1) in playback mode. Viewing Pictures on a Computer Read this section for information on copying pictures to a computer. Windows Use MyFinePix Studio to copy pictures to your computer, where they can be stored, viewed, organized, and printed. MyFinePix Studio is available for download from the following website: http://fujifilm-dsc.com/mfs/ Once download is complete, double-click the downloaded file (“MFPS_Setup.EXE”) and follow the on-screen instructions to complete installation. Proceed to “Connecting the Camera” (P 124) when installation is complete. Macintosh Pictures can be copied to your computer using Image Capture (supplied with your computer) or other software. Proceed to “Connecting the Camera” (P 124). Connections Viewing RAW Files To view RAW files on your computer, use the RAW FILE CONVERTER, available for download from: http://fujifilm-dsc.com/rfc/ 123 Viewing Pictures on a Computer Connecting the Camera 1 Find a memory card containing pictures you want to copy to the computer and insert the card into the camera. R Windows users may require the Windows CD when starting the software for the first time. Q Loss of power during transfer could result in loss of data or damage to the memory card. Insert a fresh or fully-charged battery before connecting the camera. 2 Turn the camera off and connect a USB cable (available separately from third-party suppliers) as shown, making sure the connectors are fully inserted. Connect the camera directly to the computer; do not use a USB hub or keyboard. Q The USB cable must be no more than 1.5 m (4.9 ft.) long and be suitable for data transfer. 3 Turn the camera on. 4 Copy pictures to the computer using MyFinePix Studio or applications provided with your operating system. For more information on using the software, start the application and select the appropriate option from the Help menu. 124 Viewing Pictures on a Computer Q If a memory card containing a large number of images is inserted, there may be a delay before the software starts and you may be unable to import or save images. Use a memory card reader to transfer pictures. Q Make sure that the computer does not display a message stating that copying is in progress and that the indicator lamp is out before turning the camera off or disconnecting the USB cable (if the number of images copied is very large, the indicator lamp may remain lit after the message has cleared from the computer display). Failure to observe this precaution could result in loss of data or damage to the memory card. Q Disconnect the camera before inserting or removing memory cards. Q In some cases, it may not be possible to access pictures saved to a network server using the software in the same way as on a standalone computer. Q The user bears all applicable fees charged by the phone company or Internet service provider when using services that require an Internet connection. Disconnecting the Camera After confirming that the indicator lamp is out, turn the camera off and disconnect the USB cable. Connections 125 Creating a DPOF Print Order The C PLAY BACK MENU > PRINT ORDER (DPOF) (P 105) option can be used to create a digital “print order” for DPOF-compatible printers. DPOF DPOF (Digital Print Order Format) is standard that allows pictures to be printed from “print orders” stored on the memory card. The information in the order includes the pictures to be printed and the number of copies of each picture. ■ WITH DATE s/ WITHOUT DATE To modify the DPOF print order, select C PLAY BACK MENU > PRINT ORDER (DPOF) (P 101) and press the selector up or down to highlight WITH DATE s or WITHOUT DATE. PLAY BACK MENU COPY WIRELESS COMMUNICATION WITH DATE SLIDE SHOW WITHOUT DATE PHOTOBOOK ASSIST RESET ALL PC AUTO SAVE PRINT ORDER(DPOF) PRINTER PRINT DISP ASPECT WITH DATE s: Print date of recording on pictures. WITHOUT DATE: Print pictures without date. Press MENU/OK and follow the steps below. 1 Press the selector left or right to display a picture you wish to include in or remove from the print order. 2 Press the selector up or down to choose the number of copies (up to 99). To remove a picture from the order, press the selector down until the number of copies is 0. PRINT ORDER (DPOF) DPOF: 00001 Total number of prints Number of copies 01 SHEETS FRAME 126 SET Creating a DPOF Print Order 3 Repeat steps 1–2 to complete the print order. Press MENU/OK to save the print order when settings are complete, or DISP/BACK to exit without changing the print order. 4 The total number of prints is displayed in the monitor. Press MENU/OK to exit. The pictures in the current print order are indicated by a u icon during playback. ■ RESET ALL To cancel the current print order, select RESET ALL for C PLAY BACK MENU > PRINT ORDER (DPOF) (P 101). The confirmation shown at right will be displayed; press MENU/OK to remove all pictures from the order. RESET DPOF OK? YES CANCEL Connections R Print orders can contain a maximum of 999 pictures. RESET DPOF OK? R If a memory card is inserted containing a print order created by another camera, the message shown at right will YES NO be displayed. Pressing MENU/OK cancels the print order; a new print order must be created as described above. 127 instax SHARE Printers Print pictures from your digital camera to instax SHARE printers. Establishing a Connection Select D CONNECTION SETTING > instax PRINTER CONNECTION SETTING (P 117) and enter the instax SHARE printer name (SSID) and password. The Printer Name (SSID) and Password The printer name (SSID) can be found on the bottom of the printer; the default password is “1111”. If you have already chosen a different password to print from a smartphone, enter that password instead. 128 SSID :in Xxxx stax-12 3456 XxxxxXxxx XX 7 XxxxxXxxx XX::00000000 8 xXxx x XX:000000000 000 0 instax SHARE Printers Printing Pictures 1 Turn the printer on. 3 Use the selector to display the picture you want to print, then press MENU/OK. PRINTER PRINT TRANSMIT instax-12345678 2 Select C PLAY BACK MENU > instax PRINT- CANCEL R Pictures taken with other cameras can not be printed. R The area printed is smaller than the area visible in the LCD monitor. 4 The picture will be sent to the printer and printing will start. PRINTER PRINT instax-12345678 CONNECTING TO PRINTER FUJIFILM-CAMERA-1234 Connections ER PRINT (P 101). The camera will connect to the printer. 100-0020 CANCEL R To print a frame from a burst sequence, display the frame before selecting instax PRINTER PRINT. PRINTER PRINT instax-12345678 SENDING FUJIFILM-CAMERA-1234 CANCEL 129 Viewing Pictures on TV To show pictures to a group, connect the camera to a TV using an HDMI cable (available separately from third-party suppliers; note that the TV can only be used for playback, not shooting). 1 Turn the camera off. 2 Connect the cable as shown below. Insert into HDMI connector Insert into Micro HDMI connector Q Use an HDMI cable no more than 1.5 m (4.9 ft.) long. R Be sure the connectors are fully inserted. 3 Tune the television to the HDMI input channel. See the documentation supplied with the television for details. 4 Turn the camera on and press a button. The camera monitor turns off and pictures and movies are played back on the TV. Note that the camera volume controls have no effect on sounds played on the TV; use the television volume controls to adjust the volume. R The USB cable can not be used while an HDMI cable is connected. R Some televisions may briefly display a black screen when movie playback begins. 130 Technical Notes Optional Accessories The camera supports a wide range of accessories from FUJIFILM and other manufacturers. Accessories from FUJIFILM The following optional accessories are available from FUJIFILM. For the latest information on the accessories available in your region, check with your local FUJIFILM representative or visit http://www.fujifilm.com/ products/digital_cameras/index.html. Rechargeable Li-ion batteries NP-W126: Additional large-capacity NP-W126 rechargeable batteries can be purchased as required. AC power adapters AC-9V (requires CP-W126 DC coupler): Use for extended shooting and playback or when copying pictures to a computer. DC couplers CP-W126: Connect the AC-9V to the camera. Technical Notes Battery chargers BC-W126: Replacement battery chargers can be purchased as required. At +20 °C/+68 °F, the BC-W126 charges an NP-W126 in about 150 minutes. Remote releases RR-90: Use to reduce camera shake or keep the shutter open during a time exposure. 131 Optional Accessories Stereo microphones MIC-ST1: An external microphone for movie recording. FUJINON lenses XF-series lenses: Interchangeable lenses for use exclusively with the FUJIFILM X-mount. XC-series lenses: Interchangeable lenses for use exclusively with the FUJIFILM X-mount. Shoe-mounted flash units EF-20: This clip-on flash unit (powered by two AA batteries) has a Guide Number of 20/65 (ISO 100, m/ft.) and supports TTL flash control. The flash head can be rotated upwards 90° for bounce lighting. EF-42: This clip-on flash unit (powered by four AA batteries) has a Guide Number of 42/137 (ISO 100, m/ft.) and supports TTL flash control and auto power zoom in the range 24–105 mm (35 mm format equivalent). The flash head can be rotated 90° up, 180° left, or 120° right for bounce lighting. EF-X20: This clip-on flash unit has a Guide Number of 20/65 (ISO 100, m/ft.). Grips MHG-XPRO2: Features an improved grip. Batteries and memory cards can be removed with the grip in place, and the grip is equipped with a rail for quick-shoe camera mounts. The tripod mount can be aligned with the lens optical axis. Leather cases BLC-XPRO2: This case combines practicality with the luxury of leather and comes with a cloth that can be used to wrap the camera before putting it in the case and on other occasions. Pictures can be taken and batteries inserted or removed with the camera still in its case. 132 Optional Accessories Grip belt GB-001: GB-001 enhances the camera’s hold, allowing users to carry the camera firmly with just one hand. Macro extension tubes MCEX-11/16: Attach between the camera and the lens to shoot at high reproduction ratios. Protective filters PRF-39/PRF-43/PRF-52/PRF-58/PRF-62/PRF-67/PRF-72/PRF-77: Use to protect the lens. Teleconverters XF1.4X TC WR: Increases the focal length of the lens by about 1.4×. Mount adapters FUJIFILM M MOUNT ADAPTER: Allows the camera to be used with a wide selection of M-mount lenses. Front lens caps FLCP-39/FLCP-43/FLCP-52/FLCP-58/FLCP-62/FLCP-67/FLCP-72/FLCP-72 II/FLCP-77: Protect the front lens element when the lens is not in use. Body caps BCP-001: Cover the camera lens mount when no lens is attached. instax SHARE printers SP-1: Connect via wireless LAN to print pictures on instax film. Technical Notes Rear lens caps RLCP-001: Protect the rear lens element when the lens is not attached to the camera. 133 Optional Accessories Connecting the Camera to Other Devices ■ Remote Shutter Release ■ External Microphones MIC-ST1 stereo microphone * RR-90 remote release * ■ Printing X-Pro2 ■ Flash Photography EF-20 shoe mount EF-42 shoe mount flash * flash * EF-X20 shoe mount flash * ■ Lens Wireless LAN XF-series lenses * SP-1 instax SHARE printer * SD/SDHC/SDXC memory card † XC-series lenses * ■ Macro Extension Tube MCEX-11/16 * ■ M Mount Adapter ■ Computer Related FUJIFILM M MOUNT ADAPTER * USB cable † ■ Audio/Visual Computer † * Available separately from FUJIFILM. † Available separately from third-party suppliers. USB cables must be no more than 1.5 m (4.9 ft.) long, HDMI cables no more than 1.5 m (4.9 ft.) long. 134 HDMI cable † HDTV † Caring for the Camera To ensure continued enjoyment of the product, observe the following precautions. ■ Water and Sand Exposure to water and sand can also damage the camera and its internal circuitry and mechanisms. When using the camera at the beach or seaside, avoid exposing the camera to water or sand. Do not place the camera on a wet surface. ■ Condensation Sudden increases in temperature, such as occur when entering a heated building on a cold day, can cause condensation inside the camera. If this occurs, turn the camera off and wait an hour before turning it on again. If condensation forms on the memory card, remove the card and wait for the condensation to dissipate. Traveling Keep the camera in your carry-on baggage. Checked baggage may suffer violent shocks that could damage the camera. Technical Notes Use and Storage Precautions If the camera will not be used for an extended period, remove the battery and memory card. Do not store or use the camera in locations that are: • exposed to rain, steam, or smoke • very humid or extremely dusty • exposed to direct sunlight or very high temperatures, such as in a closed vehicle on a very hot day • extremely cold • subject to strong vibration • exposed to strong magnetic fields, such as near a broadcasting antenna, power line, radar emitter, motor, transformer, or magnet • in contact with volatile chemicals such as pesticides • in contact with rubber or vinyl products 135 Cleaning the Image Sensor Multiple photographs marred by spots or blotches in identical locations may indicate the presence of dust on the camera image sensor. Clean the sensor using D USER SETTING > SENSOR CLEANING (P 108); if the problem persists, you can clean the sensor manually as described below. Note that there will be a charge to repair or replace the image sensor if it is damaged during cleaning. 1 Use a blower (not a brush) to remove dust from the sensor. Q Do not use a brush or blower brush. Failure to observe this precaution could damage the sensor. 2 Check whether the dust has been successfully removed. R Repeat Steps 1 and 2 as necessary. 3 Replace the body cap or lens. 136 Troubleshooting Problems and Solutions ■ Power and Battery Problem The camera does not turn on. The monitor does not turn on. The battery runs down quickly. The battery is exhausted exhausted:: Charge the battery ((P P 19) or insert a fully-charged spare battery ((P P 20). Reinsert the battery in the correct orientation and make sure that the charger is plugged in ((P P 19). Charge the battery at room temperature ((P P v). • There is dirt on the battery terminals terminals:: Clean the terminals with a soft, dry cloth. • The battery has been charged many times times:: The battery has reached the end of its charging life. Purchase a new battery. If the battery still fails to charge, contact your FUJIFILM dealer. ■ Menus and Displays Problem Display is not in English. Solution Select ENGLISH for D USER SETTING > SETTING > a ((P P 27, 108). Troubleshooting The camera turns off suddenly. Charging does not start. Charging is slow. The charging lamp blinks, but the battery does not charge. Solution • The battery is exhausted exhausted:: Charge the battery ((P P 19) or insert a fully-charged spare battery ((P P 20). • The battery is inserted incorrectly: incorrectly: Reinsert in the correct orientation ((P P 20). • The battery-chamber cover is not latched latched:: Latch the battery-chamber cover ((P P 20). The monitor may not turn on if the camera is turned off and then on again very quickly. Press the shutter button halfway to activate the monitor. • The battery is cold cold:: Warm the battery by placing it in a pocket or other warm place and reinsert it in the camera immediately before taking a picture. • There is dirt on the battery terminals terminals:: Clean the terminals with a soft, dry cloth. • ON is selected for G AF/MF SETTING > PRE-AF PRE-AF:: Turn PRE-AF off (P (P 91). • The battery has been charged many times times:: The battery has reached the end of its charging life. Purchase a new battery. 137 Problems and Solutions ■ Shooting Problem No picture is taken when the shutter button is pressed. Mottling (“noise”) appears in the monitor or viewfinder when the shutter button is pressed halfway. The camera does not focus. Intelligent Face Detection is not available. • • • • • • Solution The memory card is full full:: Insert a new memory card or delete pictures (P (P 22, 43). The memory card is not formatted formatted:: Format the memory card (P (P 107). There is dirt on the memory card contacts contacts:: Clean the contacts with a soft, dry cloth. The memory card is damaged damaged:: Insert a new memory card ((P P 22). The battery is exhausted exhausted:: Charge the battery ((P P 19) or insert a fully-charged spare battery ((P P 20). The camera has turned off automatically: automatically: Turn the camera on (P (P 25). Gain is increased to aid composition when the subject is poorly lit and aperture is stopped down, which may result in noticeable mottling when images are previewed in the displays. Images taken with the camera are unaffected. The subject is not suited to autofocus autofocus:: Use focus lock ((P P 76) or manual focus (P (P 63). Intelligent Face Detection is not available in the current shooting mode mode:: Choose a different shooting mode ((P P 153). • The subject’s face is obscured by sunglasses, a hat, long hair, or other objects objects:: Remove the obstructions. • The subject’s face occupies only a small area of the frame frame:: Change the composition so that the subject’s face occupies a larger area of the frame ((P P 92). No face is detected. • The subject’s head is tilted or horizontal horizontal:: Ask the subject to hold their head straight. • The camera is tilted tilted:: Keep the camera level. • The subject’s face is poorly lit lit:: Shoot in bright light. The selected subject is closer to the center of the frame than the main subject. Recompose the picture or turn face Wrong subject is selected. detection off and frame the picture using focus lock (P (P 76). 138 Problems and Solutions Problem The flash does not fire. The flash does not fully light the subject. Pictures are blurred. Pictures are mottled. Solution The flash can not be used at current settings settings:: See the list of the settings that can be used with the flash (P (P 153). The battery is exhausted exhausted:: Charge the battery ((P P 19) or insert a fully-charged spare battery ((P P 20). The subject is not in range of the flash ash:: Position the subject in range of the flash. The flash window is obstructed obstructed:: Hold the camera correctly. Shutter speed is faster than 1/250 ss:: Choose a slower shutter speed ((P P 36, 38, 79). The lens is dirty dirty:: Clean the lens ((P P xi). The lens is blocked blocked:: Keep objects away from the lens. s is displayed during shooting and the focus frame is displayed in red: red: Check focus before shooting ((P P 75). Shutter speed is slow and the ambient temperature is high: high: This is normal and does not indicate a malfunction. Pixel mapping is required: required: Perform pixel mapping using H IMAGE QUALITY SETTING > SETTING > PIXEL MAPPING (P 90). • The camera has been used continuously at high temperatures or a temperature warning is displayed displayed:: Turn the camera off and wait for it to cool down. • • • • • • • • • • Troubleshooting 139 Problems and Solutions ■ Playback Problem Pictures are grainy. Playback zoom is unavailable. No sound in movie playback. Selected pictures are not deleted. File numbering is unexpectedly reset. Solution The pictures were taken with a different make or model of camera. The pictures were created using RESIZE or with a different make or model of camera. • Playback volume is too low: low: Adjust playback volume (P (P 46, 109). • The microphone was obstructed obstructed:: Hold the camera correctly during recording ((P P 2, 44). • The speaker is obstructed obstructed:: Hold the camera correctly during playback ((P P 2, 46). Some of the pictures selected for deletion are protected. Remove protection using the device with which it was originally applied (P (P 103). The battery-chamber cover was opened while the camera was on. Turn the camera off before opening the battery-chamber cover ((P P 20, 25). ■ Connections/Miscellaneous For additional information on troubleshooting wireless connections, visit: http://faq.fujifilm.com/digitalcamera/faq_product.html?pid=X Problem Problem connecting or uploading pictures to smartphone. Can not upload images. 140 Solution • The smartphone is too far away: away: Move the devices closer. • Nearby devices are causing radio interference interference:: Move the camera and smartphone away from microwave ovens or cordless phones. • The smartphone is connected to another device device:: The smartphone and camera can connect to only one device at a time. End the connection and try again. • There are several smartphones in the vicinity vicinity:: Try connecting again. The presence of multiple smartphones can make connection difficult. • The current image is a movie or was created on another device and can not be uploaded to a smartphone. Problems and Solutions Problem Solution Select ON for D CONNECTION SETTING > WIRELESS SETTING SETTING > > RESIZE IMAGE FOR SMARTPHONE Smartphone will not H. Selecting OFF increases upload times for larger images; in addition, some phones may not display images display pictures. over a certain size. • The camera is not properly connected: connected: Connect the camera properly (P (P 130).). Note that once the camera is connected, pictures will be displayed on the TV instead of in the camera monitor. No picture or sound on TV. • Input on the television is set to “TV”: “TV”: Set input to “HDMI”. • The volume on the TV is too low: low: Use the controls on the television to adjust the volume. The computer does not Be sure the camera and computer are correctly connected ((P P 124).). recognize the camera. Can not transfer RAW or Use MyFinePix Studio to transfer pictures (Windows only; P 123).). JPEG files to computer. • Temporary camera malfunction: malfunction: Remove and reinsert the battery ((P P 20). The camera is • The battery is exhausted exhausted:: Charge the battery ((P P 19) or insert a fully-charged spare battery ((P P 20). unresponsive. • The camera is connected to a wireless LAN LAN:: End the connection. The camera does not funcRemove and reinsert the battery ((P P 20). If the problem persists, contact your FUJIFILM dealer. tion as expected. No sound. Adjust the volume (P (P 109). Troubleshooting 141 Warning Messages and Displays The following warnings appear in the display. Warning i (red) j (blinks red) s (displayed in red with red focus frame) Aperture or shutter speed displayed in red FOCUS ERROR TURN OFF THE CAMERA AND TURN ON AGAIN LENS CONTROL ERROR LENS ERROR BUSY CARD NOT INITIALIZED PROTECTED CARD 142 Description Low battery. Charge the battery ((P P 19) or insert a fully-charged spare battery ((P P 20). Battery exhausted. Charge the battery ((P P 19) or insert a fully-charged spare battery ((P P 20). The camera can not focus. Use focus lock to focus on another subject at the same distance, then recompose the picture (P (P 76). The subject is too bright or too dark and the picture will be over- or under-exposed. Use the flash for additional lighting when taking photographs of poorly-lit subjects (P (P 78). Camera malfunction. Turn the camera off and then on again. If the message persists, contact a FUJIFILM dealer. Turn the camera off, remove the lens, and clean the mounting surfaces, then replace the lens and turn the camera on. If the problem persists, contact a FUJIFILM dealer. The memory card is incorrectly formatted. Use the camera to format the card ((P P 107). • The memory card is not formatted or the memory card has been formatted in a computer or other device device:: Format the memory card using D USER SETTING > SETTING > FORMAT ((P P 107). • The memory card contacts require cleaning cleaning:: Clean the contacts with a soft, dry cloth. If the message is repeated, format the card (P (P 107). If the message persists, replace the card. • Camera malfunction: malfunction: Contact a FUJIFILM dealer. The memory card is locked. Unlock the card. Warning Messages and Display Warning CARD ERROR b MEMORY FULL NO CARD WRITE ERROR READ ERROR Troubleshooting FRAME NO. FULL Description • The memory card is not formatted for use in the camera camera:: Format the card (P (P 107). • The memory card contacts require cleaning or the memory card is damaged damaged:: Clean the contacts with a soft, dry cloth. If the message is repeated, format the card (P (P 107). If the message persists, replace the card. • Incompatible memory card: card: Use a compatible card ((P P 24). • Camera malfunction: malfunction: Contact a FUJIFILM dealer. The memory card is full and pictures can not be recorded. Delete pictures (P (P 43) or insert a memory card with more free space ((P P 22). The shutter can only be released when a memory card is inserted. Insert a memory card. • Memory card error or connection error: error: Reinsert the card or turn the camera off and then on again. If the message persists, contact a FUJIFILM dealer. • Not enough memory remaining to record additional pictures pictures:: Delete pictures (P (P 43) or insert a memory card with more free space ((P P 22). • The memory card is not formatted formatted:: Format the memory card (P (P 107). • The file is corrupt or was not created with the camera camera:: The file can not be viewed. • The memory card contacts require cleaning cleaning:: Clean the contacts with a soft, dry cloth. If the message is repeated, format the card (P (P 107). If the message persists, replace the card. • Camera malfunction: malfunction: Contact a FUJIFILM dealer. The camera has run out of frame numbers (current frame number is 999-9999). Format the memory card and select RENEW for D SAVE DATA SETTING SETTING > >FRAME FRAME NO. NO... Take a picture to reset frame numbering to 100-0001, then select CONTINUOUS for FRAME NO. NO... 143 Warning Messages and Display Warning PROTECTED FRAME CAN NOT CROP m CANNOT EXECUTE F CANNOT EXECUTE CAN NOT ROTATE F CAN NOT ROTATE DPOF FILE ERROR CAN NOT SET DPOF F CAN NOT SET DPOF p (yellow) p (red) 144 Description An attempt was made to delete or rotate to a protected picture. Remove protection and try again ((P P 103). The picture is damaged or was not created with the camera. Red-eye removal can not be applied to pictures created with other devices. Red-eye removal can not be applied to movies. The selected picture can not be rotated. Movies can not be rotated. The DPOF print order on the current memory card contains more than 999 images. Copy the pictures to a computer and create a new print order. The picture can not be printed using DPOF. Movies can not be printed using DPOF. Turn the camera off and wait for it to cool. Mottling may increase in pictures taken when this warning is displayed. Turn the camera off and wait for it to cool. Display quality and burst rate will drop, and mottling may increase in pictures taken when this warning is displayed. Appendix Memory Card Capacity The following table shows the recording time or number of pictures available at different image sizes. All figures are approximate; file size varies with the scene recorded, producing wide variations in the number of files that can be stored. The number of exposures or length remaining may not diminish at an even rate. 8 GB Capacity O T FINE 540 T FINE 1110 T NORMAL 1660 150 300 320 630 26 min. 54 min. 51 min. 105 min. Appendix O3:2 Photographs RAW (UNCOMPRESSED) RAW (LOSSLESS COMPRESSED) i 1080/60 P 2 i 1080/50 P 2 i 1080/30 P 2 i 1080/25 P 2 i 1080/24 P 2 Movies 1 h 720/60 P 3 h 720/50 P 3 h 720/30 P 3 h 720/25 P 3 h 720/24 P 3 1 Use a UHS speed class 1 card or better. 2 Individual movies can not exceed 14 minutes in length. 3 Individual movies can not exceed 28 minutes in length. 16 GB T NORMAL 800 145 Links For more information on FUJIFILM digital camera, visit the websites listed below. FUJIFILM X-Pro2 Product Information Optional accessories and support information can be found on the following website. fujifilm X-Pro2 Free FUJIFILM Apps FUJIFILM apps give you more opportunities to enjoy your pictures on smartphones, tablets, and computers. http://fujifilm-dsc.com/ Firmware Updates Updates to product firmware may result in changes not described in the manual. For more information, visit: http://www.fujifilm.com/support/digital_cameras/ software/fw_table.html fujifilm firmware fujifilm Wi-Fi app For the latest version of MyFinePix Studio, visit: http://fujifilm-dsc.com/mfs/ fujifilm mfs For the latest version of RAW FILE CONVERTER, visit: http://fujifilm-dsc.com/rfc/ fujifilm rfc 146 Specifications System Model Effective pixels Image sensor Storage media Memory card slots File system File format Image size Lens mount Sensitivity Metering Exposure control Exposure compensation Shutter speed Appendix FUJIFILM X-Pro2 digital camera Approx. 24.3 million 23.5 mm × 15.6 mm (APS-C), X-Trans CMOS III sensor with primary color filter FUJIFILM-recommended SD/SDHC/SDXC memory cards Two SD memory card slot Compliant with Design Rule for Camera File System (DCF) (DCF),, Exif 2.3, and Digital Print Order Format (DPOF) • Still pictures: pictures: Exif 2.3 JPEG (compressed) (compressed);; RAW (original RAF format, uncompressed or compressed using a lossless algorithm; special purpose software required); RAW+JPEG available • Movies Movies:: H.264 standard with stereo sound (MOV) • O 3 : 2: 2: 6,000 × 4,000 • O 16 : 9: 9: 6,000 × 3,376 • O 1 : 1: 1: 4,000 × 4,000 • P 3 : 2: 2: 4,240 × 2,832 • P 16 : 9: 9: 4,240× 2,384 • P 1 : 1: 1: 2,832 × 2,832 • Q 3 : 2: 2: 3,008 × 2,000 • Q 16 : 9: 9: 3,008 × 1,688 • Q 1 : 1: 1: 2,000 × 2,000 FUJIFILM X mount Standard output sensitivity equivalent to ISO 200 – 12800; AUTO; extended output sensitivity equivalent to ISO 100, 25600, or 51200 256-segment throughhrough-tthehe-llens (TTL) metering; MULTI, SPOT, AVERAGE, CENTER WEIGHTED Programmed AE (with program shift) shift);; shutter-priority AE; aperture-priority AE; manual exposure –5 EV – +5 EV in increments of / EV • MECHANICAL SHUTTER - P mode mode:: 4 sec. to / sec. - Time Time:: 30 sec. to / sec. - Bulb Bulb:: Max. 60 min. - All other modes: modes: 30 sec. to / sec. • ELECTRONIC SHUTTER - P, S, A, and M modes modes:: 1 sec. to / sec. - Time Time:: 1 sec. to / sec. - Bulb Bulb:: Fixed at 1 sec. • MECHANICAL + ELECTRONIC - P mode mode:: 4 sec. to / sec. - Time Time:: 30 sec. to / sec. - Bulb Bulb:: Max. 60 min. - All other modes: modes: 30 sec. to / sec. 147 Specifications System Continuous Focus White balance Self-timer Flash Mode Hot shoe Sync terminal Hybrid viewfinder LCD monitor 148 Mode 8.0 fps I 3.0 fps Frame rate (fps) 8.0 3.0 Frames per burst Up to approximately 53 Up to approximately 62 R The frame rate and number of frames per burst may vary depending on the type of memory card used. The figures above are for UHS speed class 1 cards. R The frame rate varies with shooting conditions and the number of images recorded. • Mode Mode:: Single or continuous AF; manual focus with focus ring • Focus-area selection selection:: SINGLE POINT, ZONE, WIDE/TRACKING • Autofocus system: system: Intelligent hybrid AF (TTL contrast-detect/phase-detection AF) with AF-assist illuminator Custom 1, Custom 2, Custom 3, color temperature selection, auto, direct sunlight, shade, daylight fluorescent, warm white fluorescent, cool white fluorescent, incandescent, underwater Off, 2 sec., 10 sec. Accessory shoe with TTL contacts and sync contact (X contact) that supports sync speeds as fast as / / s Auto, fill flash, off, slow sync, rear-curtain sync, commander (red-eye removal off );); auto with red-eye removal, fill flash with red-eye removal, off, slow sync with red-eye removal, rear-curtain sync with red-eye removal, commander (red-eye removal on) Accessory shoe with TTL contacts Provided • Optical viewfinder (OVF): (OVF): Reverse Galilean viewfinder with electronic bright frame display and approx. 0.36×/0.6× magnification; frame coverage approx. 92% • Electronic viewfinder (EVF) (EVF):: 0.48-in., 2,360k-dot color LCD viewfinder with diopter adjustment (–4 to +2 m–1); magnification 0.59× with 50 mm lens (35 mm format equivalent) at infinity and diopter set to –1.0 m–1; diagonal angle of view approximately 29.1° (horizontal angle of view approximately 24.4°); eye point approx. 16 mm Fixed 3.0-in/7.6 cm, 1620k-dot color LCD monitor Specifications System Movies • • • • • • • • • • i 1080/60P 1080/60P:: Frame size 1,920 × 1,080 (1080p); 60 fps; stereo sound i 1080/50P 1080/50P:: Frame size 1,920 × 1,080 (1080p); 50 fps; stereo sound i 1080/30P 1080/30P:: Frame size 1,920 × 1,080 (1080p); 30 fps; stereo sound i 1080/25P 1080/25P:: Frame size 1,920 × 1,080 (1080p); 25 fps; stereo sound i 1080/24P 1080/24P:: Frame size 1,920 × 1,080 (1080p); 24 fps; stereo sound h 720/60P 720/60P:: Frame size 1,280 × 720 (720p); 60 fps; stereo sound h 720/50P 720/50P:: Frame size 1,280 × 720 (720p); 50 fps; stereo sound h 720/30P 720/30P:: Frame size 1,280 × 720 (720p); 30 fps; stereo sound h 720/25P 720/25P:: Frame size 1,280 × 720 (720p); 25 fps; stereo sound h 720/24P 720/24P:: Frame size 1,280 × 720 (720p); 24 fps; stereo sound Input/output terminals HDMI output Micro HDMI connector (Type D) Digital input/output Micro USB connector (USB 2.0 High-Speed) Microphone/ φ2.5 mm mini-stereo jack remote release connector EVF 210 250 330 OVF 350 350 380 CIPA standard, measured using battery supplied with camera and SD memory card. Appendix Power supply/other Power supply NP-W126 rechargeable battery Battery life (approximate • Battery type type:: NP-W126 (type supplied with camera) number of frames that can • Approximate number of frames frames:: be taken with a fully-charged LCD battery in mode P, XF 35 mm HIGH PERFORMANCE 250 f/1.4 R lens) STANDARD 280 ECONOMY 330 Note: Number of shots that can be taken with battery varies with battery charge level and will decline at low Note: temperatures. 149 Specifications Power supply/other Camera size (W × H × D) Camera weight Shooting weight Operating conditions Wireless transmitter Standards Operating frequency Access protocols 150 140.5 mm × 82.8 mm × 45.9 mm (34.8 (34.8 mm excluding projections, measured at thinnest part)/5.5 part)/5.5 in. × 3.3 in. × 1.8 in. (1.4 in.) Approx. 445 g/15.7 oz., excluding battery, accessories, and memory card Approx. 495 g/17.5 oz., including battery and memory card • Temperature Temperature:: –10 °C to +40 °C/+32 °F to +104 °F • Humidity Humidity:: 10% – 80% (no condensation) IEEE 802.11b/g/n (standard wireless protocol) • U. S. A., Canada, Taiwan: Taiwan: 2,412 MHz–2,462 MHz (11 channels) • Other countries: countries: 2,412 MHz–2,472 MHz (13 channels) Infrastructure Specifications NP-W126 rechargeable battery Nominal voltage 7.2 V DC Nominal capacity 1,260 mAh Operating temperature 0 °C to +40 °C/+32 °F to +104 °F Dimensions (W × H × D) 36.4 mm × 47.1 mm × 15.7 mm/1.4 in. × 1.9 in. × 0.6 in. Weight Approx. 47 g/1.7 oz. BC-W126 battery charger Rated input Input capacity Rated output Supported batteries Charging time Operating temperature Dimensions (W × H × D) Weight 100 V – 240 V AC, 50/60 Hz 13 –21 VA 8.4 V DC, 0.6 A NP-W126 rechargeable batteries Approx. 150 minutes (+20 °C/+68 °F) 5 °C to +40 °C/+41 °F to +104 °F 65 mm × 91.5 mm × 28 mm/2.6 in. × 3.6 in. × 1.1 in., excluding projections Approx. 77 g/2.7 oz., excluding battery Weight and dimensions vary with the country or region of sale. Labels, menus, and other displays may differ from those on the actual camera. Appendix 151 Specifications ■ Notices • Specifications subject to change without notice; for the latest information, visit http://www.fujifilm.com/products/ digital_cameras/index.html. FUJIFILM shall not be held liable for damages resulting from errors in this manual. • Although the viewfinder and LCD monitor are manufactured using advanced high-precision technology, small bright points and anomalous colors may appear, particularly in the vicinity of text. This is normal for this type of LCD display and does not indicate a malfunction; images recorded with the camera are unaffected. • Digital cameras may malfunction when exposed to strong radio interference (e.g., electric fields, static electricity, or line noise). • Due to the type of lens used, some distortion may occur at the periphery of images. This is normal. 152 Restrictions on Camera Settings The options available in each shooting mode are listed below. Some options may not be available for the items that are supported in any given mode, and function may be restricted depending on shooting conditions. P S A M R BKT j Y F r8 F S.S. Program shift Exposure compensation ✔1 ✔1 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔4 ✔ ✔1 ✔ ✔4 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔5 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔3 ✔ ✔ ✔3 ✔3 ✔ ✔ ✔ ✔ ✔3 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔3 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔ ✔7 ✔ ✔7 ✔1 ✔7 ✔ ✔ ✔ ✔ ✔ ✔ ✔7 ✔7 ✔7 ✔7 ✔7 ✔ ✔ ✔ ✔ ✔ ✔ ✔7 S C M AUTO H (51200) /H (25600) 12800 – 1000 800 640 – 200 L (100) O P Q FINE/NORMAL RAW c d/e/i g/h a/d/c/b b/e/d/f f Focus mode Sensitivity IMAGE SIZE IMAGE QUALITY FILM SIMULATION GRAIN EFFECT ✔ ✔2 ✔ ✔ ✔ ✔ ✔ ✔ ✔9 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ Appendix Shooting mode/scene position 153 Restrictions on Camera Settings Shooting mode/scene position AUTO V/W/X DYNAMIC RANGE WHITE BALANCE HIGHLIGHT TONE SHADOW TONE COLOR SHARPNESS NOISE REDUCTION LONG EXPOSURE NR LENS MODULATION OPTIMIZER COLOR SPACE SELECT CUSTOM SETTING EDIT/SAVE CUSTOM SETTING r y z AF MODE AF ILLUMINATOR FACE DETECTION EYE DETECTION AF AF+MF STANDARD DIGITAL SPLIT IMAGE FOCUS PEAK HIGHLIGHT MF ASSIST FOCUS CHECK SELF-TIMER PHOTOMETRY 154 o p v w P S A M R BKT ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ j ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔ ✔ ✔ ✔ ✔ Y F r8 ✔ ✔ ✔1 ✔1 ✔7 ✔7 ✔ ✔7 ✔7 ✔7 ✔7 ✔7 ✔7 ✔7 ✔7 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔6 ✔1 ✔1 ✔7 ✔ ✔1 ✔ ✔7 ✔ ✔7 ✔7 Restrictions on Camera Settings Shooting mode/scene position t t+s s l m OFF SHUTTER TYPE IS MODE RED EYE REMOVAL: OFF FLASH MODE RED EYE REMOVAL: ON FLASH COMPENSATION RED EYE REMOVAL PREVIEW EXP./WB IN MANUAL MODE A N F l D P K L M d D P P S A M R BKT j Y ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔3 ✔3 ✔3 ✔3 ✔3 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔3 ✔3 ✔3 ✔3 ✔3 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔7 ✔7 ✔7 ✔7 ✔7 ✔7 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔7 ✔ ✔ ✔ ✔ ✔7 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ F ✔1 ✔ ✔ ✔ r8 Appendix 155 Restrictions on Camera Settings Shooting mode/scene position DISP. CUSTOM SETTING AF-LOCK MODE 156 1 2 3 4 5 FRAMING GUIDELINE ELECTRONIC LEVEL FOCUS FRAME AF DISTANCE INDICATOR MF DISTANCE INDICATOR HISTOGRAM SHOOTING MODE APERTURE/S-SPEED/ISO INFORMATION BACKGROUND Expo. Comp. (Digit) Expo. Comp. (Scale) FOCUS MODE PHOTOMETRY SHUTTER TYPE FLASH CONTINUOUS MODE DUAL IS MODE WHITE BALANCE FILM SIMULATION DYNAMIC RANGE FRAMES REMAINING IMAGE SIZE/QUALITY MOVIE MODE & REC. TIME BATTERY LEVEL AF-L AE+AF Fixed automatically. Restricted to range of ±2.0 EV during movie recording. Options available vary with shooting mode. A is not available. Available only with auto ISO sensitivity. P S A M R BKT j Y ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ 6 7 8 9 F r8 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ sRGB selected automatically. Still photography settings are used. Wireless remote photography. Maximum sensitivity for movies is ISO 6400. ✔ ✔ ✔ ✔ ✔ ✔7 ✔7 Memo 157 7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN http://www.fujifilm.com/products/digital_cameras/index.html
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement