Rosewill ARC 750W 80 PLUS Bronze PSU User Manual

EA
AN ELSA ie) 4
USER Manual
ARC450 / M450
ARC550 / M550
ARC650 / M650
ARC750
NUNES
Contents
1> Introduction ---------------------—---———— Р. 2
2> Product Features -----------------------------—————— P.2
3> Package contents ----------------------------------———- P.2
4> Specifications -------- P. 3
5> Connectors---------==---=<""<<-<<<<<<-----s Р. 4
6> Installation-------------------------=== eee P.5
7> Safety and EMI Certification ---------------------- P.6
8> Safety and Warning------ P.6
9> Troubleshooting------------------------------ P.6
1 POWER SUPPLY
All rights reserved by Rosewill
NUNES
Introduction
Rosewill is the platform of choice for avid PC gamers and the Rosewill Arc
Power Supply series is built to the highest quality standard and delivers the
ultimate performance for enthusiasts.
Product Features
* 80 Plus Bronze certified to deliver over 85% efficiency
* ATX 12V V2.3 ready, supports to EPS 12V 2.92 and backwards compatible
with ATX 12V 2.01
* Cable management modular ( ARC-M Series)
* Active Power Factor Correction (PFC) with PF value of 0.99
* Maximum Protection: Over-voltage and over-current protection,
short circuit protection, under-voltage protection, over power protection
* Long lasting, Ultra-quiet 120mm hydraulic fan
e Extra-long cables support full size gaming chassis
e Crossfire and SLI support
e MTBF >100,000 hours at 80% load, ambient temperature at 25°C
Package Contents
ARC Series
ARC-M Series
e ARC Power Supply Unit x1
* User manual x1
* AC power cord x1
* Cable tie x1
* Mounting screws x4
* ARC-M Power Supply Unit x1
* Modular cable set x1
e User manual x1
e AC power cord x1
e Cable tie x1
e Mounting screws x4
2 POWER SUPPLY
All rights reserved by Rosewill
PATA [ PATA -M
Electronic Specifications
Model No. : ARC450/M450
AC Input
Model No. DC Output +3.3V | +5V +12V | -12V | +5VSB
Voltage Current
Max Output
Current 20A 15A 37A 0.5A | 2.5A
ARC 450 ;
100V-240V | 10A-5A | Max Combined 80W 444W | ew | 12.5W
ARC M450 Wattage
Total Output 450W
Model No. : ARC550/M550
AC Input
Model No. DC Output +3.3V | +5V +12V | -12V |+5VSB
Voltage Current
Max Output
Current 20A | 20A | 45.5A | O.5A | 2.5A
АНС 550 100V-240V | 10A-5A | Max Combined
ARC M550 Wattage 100W 546W | 6W | 12.5W
Total Output 550W
Model No. : ARC650/M650
AC Input
Model No. DC Output +3.3V | +5V +12V | -12V |+5VSB
Voltage Current
Max Output
Current 20A | 20A 54A 0.5А | 2.5A
АВС 650
100v-240V | 10A-5 | Max Combined 100W 648W | BW | 12.5W
ARC M650 Wattage
Total Output 650W
Model No. : ARC750
AC Input
Model No. DC Output +3.3V | +5V +12V | -12V |+5VSB
Voltage Current
Max Output
Current 20A | 20A | 62.5A | O.5A | 2.5A
- _ Max Combined
ARC 750 |100V-240V | 10A-5A Wattage 100W 750W | ew |12.5W
Total Output 750W
3 POWER SUPPLY
All rights reserved by Rosewill
NUNES
Connectors
ARC Series
Cable S
20+4 +12V EPS 6+2 PIN SATA 4 PIN Molex 4 PIN
MainBoard 4+4 PIN PCI-E Connector | Peripheral Floppy
PIN Connector Connector Connector Connector
ARC450 1 1 1 4 3 1
АВС550 1 1 2 5 4 1
ARC650 1 1 2 6 4 1
ARC750 1 1 4 6 4 1
АНС-М Series
Cable 4 S
20+4 +12V EPS 6+2 PIN SATA 4 PIN Molex 4 PIN
MainBoard 4+4 PIN PCI-E Connector | Peripheral Floppy
PIN Connector Connector Connector Connector
Modular
ARC-M450 1 1 1 4 3 1
АВС-М550 1 1 2 5 4 1
ARC-M650 1 1 2 6 4 1
4 POWER SUPPLY
All rights reserved by Rosewill
NUNES
Installation
If replacing an existing PSU in a system, you will first need to remove the old PSU.
Please proceed as follows:
1. Disconnect the AC power cord from your existing power supply unit
2. Disconnect the power supply from all the components in the PC, make sure that
all the connectors are unplugged.
3. Remove the four screws from the rear of the case that hold the old power supply to
the chassis, and then remove the old power supply unit form case.
Installing the new Arc series power supply:
1. Make sure the 1/0 switch of the PSU is at off “O” position.
2. Install the Power supply unit in the appropriated space in the PC case and secure it
by screwing the four screws into the rear of the power supply.
3. Connect the 20+4 pin main power cable to the motherboard 20/24pin socket.
The detachable 4 pin section of the connector can be separated to support a 20 pin
connection or section together to support a 24 pin socket.
4. Connect the 4+4 PIN (8 PIN) power cable to the mainboard. If your mainboard supports
only 4 PIN jack, connect only the right side of the connector to the mainboard.
+12V CPU power connector Right Pini Pins
(EPS 8Pin/4+4Pin) ini Pina com [GT GB +12v 0
COM cam +12V DC E com |@ al +12V DC
==) сом || ОЕ +12v pc mi com [a] a +12V DC
Pin2 Pind com |G] (GIE! +12v DC
Pind Pin5
5.If your are using a graphics board with a 6 PIN/8 PIN connector please connect the
respective connector to the socket on the board.
If your graphics supports more than one socket, please connect the respective
connector to the socket on board.
6. Connect the SATA or Peripheral 4 PIN Molex connectors to the hard disk or SSDs or
optical drive.
7. Connect any others internal components that require power to the appropriate connector.
8. Make sure all the cables are securely seated
9. Connect the AC power cord into the back of the power supply and Switch on
I/O switch at input “1” position.
10. Your PSU is now connected and ready.
5 POWER SUPPLY
All rights reserved by Rosewill
NUNES
Safety and EMI Certification
® ® C
Tested To Comply BAUART
TAN A F With FCC Standards A GEPRUFT Ro H S
Cc TOV TYPE
E 307777 E 307777 cdictSdiery | APPROVED
E
FOR HOME OR OFFICE USE (Product Safe Compliant
Safety & Warning
* Due to the high voltage inside the power supply, do not attempt to remove the cover
of power supply. The warranty will be void if the cover is removed.
* Do not insert any objects into the open ventilation or fan grill area of the power supply.
® Оо not store the power supply in high humidity and high temperature environment,
¢ Do not plug or unplug the power cord with wet hand.
Troubleshooting
If you installed the new power supply and the system is not working properly,
please check the following:
* Make sure the AC power cord is plugged correctly into PSU inlet socket and
power switch is at input “I” position.
* Make sure the wall socket, extension power cord, power strip or surge protector in use,
fully functional and wall power switch turned on
* Make sure that all the connectors from power supply are correctly plugged
into the mainboard.
* Make sure there are no short circuits within the systems that could result from
defective hardware or misplaced connectors
* |f your are not sure take all parts out of the housing and only leave the mainboard
inside together with the power supply. Disconnect all plugs, check them and then
connect them again to the respective sockets.
Information
Thank you for purchasing a High-Quality Rosewill Product.
Please register your product at : www.rosewill.com for complete warranty information and
future support for your product.lf you have any question while using our products,
please feel free to contact us at [email protected]
Support Phone Number: 800-575-9885
Support Email: [email protected]
6 POWER SUPPLY
All rights reserved by Rosewill
Hosewitl
www.rosewill.com