Quick Start

Quick Start
VIEWSIZE THE WORLD
VSP 3600 – Quick Start
For full installation, configuration, and operation details, refer to the
VSP 3600 user manual, which is available at www.rgblink.com.
This guide provides quick start instructions for an experienced installer to set
up and operate the VSP 3600.
NOTE
Installation and cabling features
Rear Panel
Connections
1 Dial switch
2 10/100M Internet Control Port
3 USB Control Port
4 RS232 Control Port
5 ~ 8 DVI Loop Out
9 ~ 12 VGA Output Port DB-15
13 ~ 16 DVI Input Port DVI-I
17 ~ 20 DVI Output Port DVI-I
21 22 Power Switch Button
and Power Port IEC-3
Step 1-Mounting
Turn off or disconnect all equipment power sources.
Step 2- DVI Input DVI-I
DVIinput ports support signal sources
of HDM I from high-definition player
or DVI from PC
NOTE Comments to use the programs video when
connect with HDMI from high definition
player.
Step 3- DVI Loop Out
Can connect the next level VSP 3600
or the device with DVI loop out.
Step 6- Lan Control Port
Use twist CAT5 cable to connect to LAN port, operator
can control VSP 3600 based on default IP address:
192.168.0.100. Operator can also change the IP address
by RS 232 or USB.
Twist CAT5 should be one end in T568A, and another
end in T568B standard.
Step 4-VGA Output DB15
Used to connect VGA monitor,
projector or other display system.
Step 5- DVI Output DVI-I
Used to connect display system with
DVI input port or LED display control
system; DVI 1 output acts as the default
program output.
NOTE Comments to use the sending cards box,
Driver, DV4 from RGBlink for that VSP3600
can not support sending card installed inside.
Crossover Cable
Pins
Insert Twisted
Pair Wires
RJ-45
Connector
Pin
End 1
Wire color
1
2
3
4
5
6
7
8
White-green
Green
White-orange
Blue
White-blue
White-orange
White-brown
Brown
End 2
Wire color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
T568A
T568B
CAT5 is wired as T568A at one end and T568B at the
other(Tx and Rx pairs reversed) is crossover.
Step 7-USB Port
Use USB cable to connect the VSP 3600 and
computer.
Address: S603~S604, Weiye Building, Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian, China
Tel: 00865925771197
Fax:00865925771202
Email: [email protected]
http://www.rgblink.cn
VSP 3600 Quick Start
Version 1.1
Page 1 of 4
Step 8- Serial Port
Use RS232 to RJ11 cable to connect a control system
or computer to the back panel RJ11 port and the other
end on RS232 port. RS232 to RJ11 cable as following
definition.
Pin RS-232
Insert Twisted
Pair Wires
RS232/RS422
Connector
Function
RS-422
Function
TXRXGND
RX+
TX+
Transmit(-)
Receive(-)
Signal Ground
Receive(+)
Transmit(+)
2
3
5
7
8
TX
RX
GND
-----
Transmit
Receive
Signal Ground
Not Used
Not Used
Pin
RJ-11
Function
1
2
3
4
--RX
TX
GND
Not Used
Receive
Transmit
Signal Ground
Insert Twisted
Pair Wires
RJ11 Connector
Step 9- Power Port
1024×768×60Hz, 1280×720×60Hz,1280×768×60Hz,
1280×1024×60Hz,1360x768x60Hz,1366x768x60Hz,
1400x1050x60Hz,1440x900x60Hz,1600×1200×60Hz,
1680x1050x60Hz,1920×1080×60Hz,1920x1200x60Hz,
2048x1152x60Hz;
Step 2-Programming input signal
VSP 3600 supports 4 DVI( compatible with HDM1.3),
and supports max input resolution 2048x1152x60Hz.
NOTE Operating as following:
1. In LAYER part, it can be programmed only when
A, B, C, D button lights and blinks;
2. In FUNCTIONS part, push Program button to light;
3. In SOURCES part, push button to select 1, 2, 3, 4, it
will light to show that its corresponding channel is
programmed into the current layer;
4. In FUNCTIONS part, push Program and its light
will be out to show the program operation of channels
is completed.
Plug in power cord which has IEC connector, VSP
3600 has two power ports with one for backup power Step 3-Set Output
and support AC power from 90 to 264 VAC,50-60Hz,
1. In OUTPUTS part, push DVI1, DVI2, DVI3, DVI4
which means world wide compatible.
and it will light to show it is being programmed;
OUTPUTS part button DVI1 is correspond with DVI1
and VGA1;
OUTPUTS part button DVI2 is correspond with DVI2
and VGA2;
OUTPUTS part button DVI3 is correspond with DVI3
Power On
and VGA3;
OUTPUTS part button DVI4 is correspond with DVI4
Push power button switcher to ON position. LCD
and VGA4;
module on the front panel will show Video Processor
2. In FUNCTIONS part, push Add Layer to add layer
and VSP 3600 model information, and go into self
verification before it load the last setting configuration to output channel which means adding the quantity of
data and send the processed image to the target display layer;
3. In FUNCTIONS part, push Clear Layer to reduce
or device. For the first time running, CV1 input is the
layer of output channel which means reducing the
default input source.User can operate with VSP 3600
quantity of layer;
with local front panel and remote control with the
software run on the PC, remote control by RS232, USB 4. In LAYER FUNCTIONS part, push Program to
program input channel which means program the input
or TCP/IP.
signal of output screen;
Local Control-Front Panel Operation
5. In CUSTOM ADJUSTMENTS part, push Scale to
adjust the size of image which means to scale or zoom
of the image;
6. In CUSTOM ADJUSTMENTS part, push Crop to
crop the image which means to crop the input signal of
Step 1-Set Output Resolution
Press MENU button, and spin Up/Down knob to select the output screen;
7. In CUSTOM ADJUSTMENTS part, push Position
OUTPUT CONFIG. Press NEXT and spin Up/Down
knob to select OUTPUT FORMAT. Press NEXT and to adjust the position of the corresponding input image
of the layer which means to adjust the position of
spin Left/Right knob to select OUTPUT
output screen.
RESOLUTION. Then press NEXT to setup.
NOTE VSP 3600 supports output resolution as
following:
Address: S603~S604, Weiye Building, Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian, China
Tel: 00865925771197
Fax:00865925771202
Email: [email protected]
http://www.rgblink.cn
VSP 3600 Quick Start
Version 1.1
Page 2 of 4
Step 4-Save
LOAD FROM 7 corresponding button DVI2 in
OUTPUTS area;
When VSP 3600 function setting is finished, VSP
LOAD FROM 8 corresponding button DVI3 in
3600 supports 10 saving modes to avoid resetting of
OUTPUTS area;
the same steps.
1. In CUSTOM ADJUSTMENTS part, push Save and LOAD FROM 9 corresponding button DVI4 in
OUTPUTS area;
it will light to enter save option;
LOAD FROM 10 corresponding button Freeze in Layer
2. Rotate Up/Down knob to select the save path from
Functions area;
SAVE1 to SAVE10 which is shown on the LCD
Save 1 is the default mode for loading to
screen; Meanwhile 1,2,3,4 button in SOURCES,
NOTE
use when VSP 3600 is power on.
DVI1, DVI2, DVI3, DVI4 button in OUTPUTS, ALL
and Freeze button will light. Select the corresponding Factory Reset: When there is wrong operation during
parameter adjustment, users can recall the device and
path to save and press the corresponding button to
readjust the parameter. Following the steps: Press
complete, then all these buttons' lights are out.
SAVE TO 1 corresponding button 1 in SOURCES area; MENU button ,choose the submenu Reset and press
SAVE TO 2 corresponding button 2 in SOURCES area; NEXT to initiate factory reset.
SAVE TO 3 corresponding button 3 in SOURCES area;
FAQ solutions
SAVE TO 4 corresponding button 4 in SOURCES area;
Display has no output image
SAVE TO 5 corresponding button ALL;
SAVE TO 6 corresponding button DVI1 in OUTPUTS Assure there are input signals: Press【MENU】
area;
and go into【Device Info】, press the knob to cofirm,
SAVE TO 7 corresponding button DVI2 in OUTPUTS check the input signal sources, if appear <NO
area;
INPUT>, please check the connection; If use PC DVI
SAVE TO 8 corresponding button DVI3 in OUTPUTS or VGA as signal source, please set the display card
area;
to dual display or expanding mode;
SAVE TO 9 corresponding button DVI4 in OUTPUTS Assure there are output signals: Get a monitor with
area;
VGA or DVI port, connect it to device output port,
SAVE TO 10 corresponding button Freeze in Layer
see if the monitor can display normally. If unnormal,
Functions area;
check if the input signals are connected or if the
output cable contacts good.
Step 5
Load the saved modes
When VSP 3600 function setting is finished, VSP 3600
supports 10 saved modes to avoid resetting of the same
steps. All those 10 save modes can be loaded to use.
1. In CUSTOM ADJUSTMENTS part, push Load and
it will light to enter load option;
2. Rotate Up/Down knob to select the load from
SAVE1 to SAVE10 which is shown on the LCD
screen; Meanwhile 1,2,3,4 button in SOURCES, DVI1,
DVI2, DVI3, DVI4 button in OUTPUTS, ALL and
Freeze button will light. Select the corresponding path
to load and press the corresponding button to complete,
then all these buttons' lights are out.
LOAD FROM 1 corresponding button 1 in SOURCES
area;
LOAD FROM 2 corresponding button 2 in SOURCES
area;
LOAD FROM 3 corresponding button 3 in SOURCES
area;
LOAD FROM 4 corresponding button 4 in SOURCES
area;
LOAD FROM 5 corresponding button ALL;
LOAD FROM 6 corresponding button DVI1 in
OUTPUTS area;
Display blinks
Check if preview output is normal: Get a monitor
with VGA or DVI port and connect to the device
output port, check if the monitor displays normally;
If no blinks, check if DVI output plugs tight or
change the DVI cable that connects sending card, if
the monitor blinks, please check if input signal,
input connecting cable and input port are normal.
Display only shows part of the image
Scale the image: Press 【Scale】, rotate the knob to
adjust the size of screen, including width, height and
starting position, press 【Next】to confirm.
Display shows no bottom half part
Incorrect output resolution: Confirm the width and
height point on the screen, and select more adequater
resolution than screen width, press 【Next】 to
confirm.
Black edge appears on left or top
Adjust device DVI output DE excursion, press
MENU, select XY_POS, press the knob to confirm, if
LED screen top part appears black edge, adjust V_S
Address: S603~S604, Weiye Building, Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian, China
Tel: 00865925771197
Fax:00865925771202
Email: [email protected]
http://www.rgblink.cn
VSP 3600 Quick Start
Version 1.1
Page 3 of 4
via rotate the knob; if LED screen left part appears
black edge, adjust H_S via rotate the knob. After
setting, please save the parameter to SAVE1.
All buttons light on together
Check if the dial switch is normal;
Power off the device, check if two red dial switches
on back left part of the device are all upwards, if not,
place them upwards, then power on the device again.
The red dial switches are mainly for upgrade.
Address: S603~S604, Weiye Building, Torch Hi-Tech Industrial Development Zone, Xiamen, Fujian, China
Tel: 00865925771197
Fax:00865925771202
Email: [email protected]
http://www.rgblink.cn
VSP 3600 Quick Start
Version 1.1
Page 4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement