5 GHz 300Mbps Outdoor AP Router

5 GHz 300Mbps Outdoor AP Router
5 GHz 300Mbps Outdoor AP Router
Model No. iB-OR5A5300N
Ver.: 1.0.0
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
pro-vide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not in-stalled and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.

Consult the dealer or an experienced radio / TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1)
This device may not cause harmful interference.
2)
This device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
CONTENTS
1.
2.
3.
4.
5.
6.
7.
8.
9.
Package contents............................................................................................................ 4
Introduction.......................................................................................................................5
Connecting the Router....................................................................................................9
Wireless........................................................................................................................... 11
Wireless Configuration guideline................................................................................ 14
AP – Wireless Basic Setting....................................................................................15
WAN Settings..................................................................................................................16
Firewall.............................................................................................................................17
Maintenance....................................................................................................................22
Product Features :.......................................................................................................... 26
Package contents
The following items should be found in your package:

5 GHz 300Mbps Outdoor AP Router(iB-OR5A5300N)

DC 12V Power Adapter

POE Injector

Cable Tie

User Manual
NOTE:

Kindly use the POE Injector as provided in box packaging.

Make sure that the package contains the above items. If any of the listed items are
damaged or missing, please contact with your nearest dealer.
1. Introduction
iBall Baton iB-OR5A5300N is High Power Outdoor AP Router with reliable solution.
Enhanced Wireless data transmission rate up to 300Mbps.
Operation Mode: Access Point, Station
Wireless Mode: AP, WDS, Bridge
Antenna Type:
Internal 14dBi Directional Antenna
1.1 Main Features
 Complies with 5GHz IEEE802.11a & 802.11n standards.
 With IEEE802.3 & 802.3u standards
 1 -10/100M (RJ45) LAN port & 1- WAN port
 Broadband Internet - PPPoE, Dynamic IP & Static IP
 Station / WISP - Shares wireless Internet to wired & wireless users
 Wireless security - WEP, WPA-PSK & WPA2-PSK
 DHCP Server & Client mode
 Firewall features as IP/Port & MAC filtering
 With Virtual Server, DMZ & UPnP
 Power over Ethernet (Passive PoE)
 Mounting provision: Pole or Wall
Outdoor Unit Protection: IPX5 Standard
IPX5 Standard:
IPX5 is the grade at which product continues to function when directly subjected to 12.5 L of
water per minute from all directions using a 6.3 mm inside diameter nozzle at a distance of
approximately 3m for at least 3 minutes.
1.2 LED description
Fig.1
LED Indicator
1. PWR LED
2. Secondary LAN
State
ON
Off
The WLAN Broadband Router is powered Off.
LAN Connected
Off
LAN Disconnected
ing
Data is transmitting or receiving on the wireless.
ON
PoE Connected
Off
PoE Not Connected
Flash
ing
ON
4,5,6. WLAN LED ACT
The WLAN Broadband Router is powered ON.
ON
Flash
3. WAN / PoE
Description
Off
Flash
ing
Data is transmitting or receiving on the WAN interface.
Remote AP Connected / Wireless Working
Remote AP Disconnected / Wireless Not Working
Data is transmitting or receiving on the WLAN interface.
1.3 Port description
Interfaces
Description
Power
24V DC Power
Reset
Reset button : press for 5-10 sec & release
The RJ-45 port allows LAN connection through Cat. 5 cables.
LAN
Support Auto-Negotiation RJ45 ports, half/ full duplex; comply
with IEEE 802.3/ 802.3u respectively.
The RJ-45 port allows WAN connection through a Cat. 5 cables.
WAN/PoE
Support Auto-Negotiation RJ45 ports, half/ full duplex; comply
with IEEE 802.3/ 802.3u respectively.
1.4 Hardware installation steps
Step1: Push the button in the side to remove upper housing.
Step2: Pass through Ethernet cable from the hole; insert the cable to Secondary port.
Note: RJ-45 8P8C Ethernet cable is required.
Step3: Install the upper housing and make sure the housing is well installed.
Step4:
Install POE Injector

DC: Insert adapter

POE: This hole is linked to Secondary port of the Outdoor Router with RJ-45.

LAN: This hole is linked to LAN side PC/Hub or Router/ADSL modem device with RJ-45
Note: The above image is just for your reference, Colour of POE may vary as per product packaging..
2. Connecting the Router
2.1
System Requirements

Broadband Internet Access Service (DSL/Cable/Ethernet)

1 DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet.)

Computer with a working Ethernet Adapter and an Ethernet cable with RJ45 connector

TCP/IP protocol on each pc

Web browser, such as Microsoft Internet Explorer, Mozilla Firefox
2.2 TCP/IP Configuration
The default IP address of the iB-OR5A5300N 5 GHz 300Mbps Outdoor AP Router is 192.168.1.200
and the default Subnet Mask is 255.255.255.0. These values can be changed as per the requirement.
In this guide, we use all the default values for description.
Connect the local PC to the LAN ports of the Router. The IP address for your PC can be configured in
the following two ways.

Configure the IP address manually
1) Set up the TCP/IP protocol for your PC.
2) Configure the network parameters. The IP address is 192.168.1.xxx (“xxx” is any number
from 1 to 254), Subnet Mask is 255.255.255.0 and Gateway is 192.168.1.200 (The
Router’s default IP address).

Obtain an IP address automatically
1) Set up the TCP/IP Protocol in “Obtain an IP address automatically” mode on your PC.
2) Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection
between your PC and Router.
2.3 Connect to 5 GHz 300Mbps Outdoor AP Router
Open a WEB browser, i.e. Microsoft Internet Explorer 6.1 SP1 or above, then enter IP address as
192.168.1.200 on the URL to connect the iBall Baton iB-OR5A5300N Broadband Router.
Username: admin
|
Password: admin
3. Wireless
Wireless  Status
Click “Wireless” to go Wireless setting menu, as shown in below image.

Operation Mode: This mode the Operational mode status (Station/AP)

Channel-Band: This menu shows the Wireless Channel and Band of the device.

Rate : This menu shows the Connection Speed of the device.

SSID: Identification of Remote device’s wireless network.

BSSID: Identification of Remote device’s MAC Address.

Encryption: Security type of main SSID, in drop-down list to choose right mode you need or
disable it. Different types of security mode is : WEP, WAP-PSK & WPA2-PSK

MAC Address: Identification of device’s MAC Address.

After you login web page, Click Wireless → Basic Settings  Operation Mode 
click“Scan”→Select ”SSID”→
Enter encryption password→Select specified WAN type” PPPOE / DHCP /
Static”→click
Next Step
Note:



DHCP: If the device connects to DHCP Server of uplink or WISP, please select this mode.
The device will obtain IP address from uplink DHCP server or WISP automatically.
PPPoE: If WISP offer PPPOE access type, please select this mode. You should fill in both the
User Name and Password that your ISP supplies
Static:If WISP offer Static IP access, please select this mode and enter IP address/Subnet
Mask/Gateway and DNS server IP address
4. Network Settings:
 LAN Setting
You could change Gateway IP address here or keep defaults,then click Next
5. DHCP Server Settings:
You can enable or disable DHCP server here,then click Next
6. Wireless Settings:
To configure wireless settings of the device, you could enable or disable wireless, select security
mode / set encrypt key etc,after that click Apply to save previous settings.
Note: The device will restart after changing these settings, if you just keep defaults value please click
next for further process
7. Wireless Configuration guideline
 Station:
Click “Wireless ”→“Basic Settings” →“Station” go to basic configuration page, as below image:
Note:
Station mode is use to create Bridge, WDS Bridge, WISP & Client AP router function, Router connect to access
internet

DHCP: When the Device connects to a DHCP server, or ISP support DHCP service, please
choose this type. The Device will get the IP address automatically from the DHCP server or the
WISP. Once the connection started successfully, you can access internet.

PPPoE: If your wireless ISPs supports PPPoE, you should choose this type. In this condition,
you should fill both the User Name and Password that your ISP provides.

Static IP : In this type, you should manually fill in the IP address, Subnet Mask, Default
Gateway, and DNS IP address, which are specified by your ISP. The Sixth Step:

Connection status
After you finished related configuration, and you wish to check if settings is succeed or not, please go
to “Status” page for more details.
8.
AP – Wireless Basic Setting
Access Point
Check “Basic
Setting”→“AP (Access Point)”, you’ll see in below image.
In this page you may set wireless access point as per your requirement, after that click “Apply
Changes” to save settings and restart device.
.

SSID “iBall-Baton” will broadcast its name. Select SSID you can change its
name here.

Broadcast SSID: Enable the option, SSID will be visible you can see the SSID
name by PC or laptop’s wireless scan tools, once you disable it user couldn’t
find the SSID by scanning tools, the SSID has been hided, but if you still wish
to connect with the SSID, just enter the SSID manually.

Authentication: In this option you can configure encryption mode, key
etc…security mode currently support Open WEP, WPA-PSK, WPA2-PSK.

9.
Security Type: Suggest security type to be TKIP mode which is better encryption type.
WAN Settings
Check
below image.
“Basic
Setting”→“AP (Access Point)” / Station / WAN Settings, you’ll see in
 Bridge -This menu will Create Bridge between both Ethernet Ports.
 WDS Bridge: This menu can create WDS Wireless Bridge between Remote
access

Point at far end distance.
DHCP: In this option configure Dynamic IP address type of connection
WAN Port or to create WISP Wireless ISP connection.

Static IP: In this option you can configure Static IP address type of
connection
WAN Port or to create WISP Wireless ISP
connection.

PPPoE: In this option you can configure PPPoE (Username & Password)
type of connection WAN Port or to create WISP Wireless ISP connection.

PPPTP: In this option you can configure PPPTP (Username & Password)
type of connection WAN Port or to create WISP Wireless ISP connection.

L2TP: In this option you can configure L2TP (Username & Password) type of
connection WAN Port or to create WISP Wireless ISP connection.
10. Firewall
Click “Firewall” to go to advanced security option as Forwarding, URL Filtering, IP Filtering.
 IP / Port Filtering
IP / Port Filtering Filter includes both outbound filter and inbound filter. And they have same way to
setting. It enables you to control what packets are allowed to pass the router. Outbound filter
applies on all outbound packets. However, inbound filter applies on packets that destined to Virtual
Servers or DMZ host only. You can select one of the two filtering policies: White list / Blacklist.
1.
White list - Allow all to pass except those match the specified rules.
2.
Black List - Deny all to pass except those match the specified rules.
3.
Disable – Disable the filtering Rule.
 MAC Filtering
MAC Filtering allows you to assign different access right for different users and to assign a
specific IP address to a certain MAC address
4.
. White list - Allow all to pass except those match the specified rules.
5.
Black List - Deny all to pass except those match the specified rules.
6.
Disable – Disable the filtering Rule.
 URL Filtering
URL Filtering will block LAN computers to connect with pre-define Websites. The major difference
between “Domain filter” and “URL Blocking” is Domain filter requires user to input suffix (like .com
or .org, etc), while URL Blocking requires user to input a keyword only. In other words, Domain
filter can block specific website, while URL Blocking can block hundreds of websites by simply a
keyword.
 Port Forwarding
This product’s NAT firewall filters out unrecognized packets to protect your Intranet, so all hosts
behind this product are invisible to the outside world. If you wish, you can make some of them
accessible by enabling the Virtual Server Mapping.
For example, if you have an FTP server (port 21) at 192.168.1.192, a Web server (port 80) at then
you need to specify the following table:
 DMZ
DMZ (Demilitarized Zone) Host is a host without the protection of firewall. It allows a computer
to be exposed to unrestricted 2-way communication for Internet games, Video conferencing,
Internet telephony and other special applications.
 Dynamic DNS
To host your server on a changing IP address, you have to use dynamic domain name service
(DDNS). Therefore, anyone wishing to reach your host only needs to know the name of it. Dynamic
DNS will map the name of your host to your current IP address, which changes each time you
connect your Internet service provider.
Before you enable Dynamic DNS, you need to register an account on one of these Dynamic DNS
servers that we list in Provider field.
1.
DDNS: Select enable if you would like to trigger this function.
2.
Service Provider: The DDNS provider supports service for you to bind your IP(even private
IP) with a certain Domain name. You could choose your favorite provider.
3.
Domain Name: Register a domain name to the DDNS provider. The fully domain name is
concatenated with hostname (you specify) and a suffix (DDNS provider specifies).
4.
Username/E-mail: Input username or E-mail based on the DDNS provider you select.
5.
Password/Key: Input password or key based on the DDNS provider you select.
Afterwards, click on “Apply Changes ” to store your settings or click “Cancel” to give up the changes.
 Others
There are six submenus under the Security menu as shown in
 Enable UPnP, Enable Ping Access to WAN,
 Enable Web Server access on WAN,
 Enable IPsec VPN Pasthrough,
 PPTP VPN Pasthrough,
 L2TP VPN Pasthrough
Click any of them, and you will be able to configure the corresponding function.
11. Maintenance
Click “System Tools” to go to system management menu, as shown in below image.
Choose menu “Maintenance”, you can see the submenus under the main menu: Time Settings,
System Log, Firmware Upgrade, Factory Defaults, Backup & Restore, Restart, Password,
Diagnostic Tool and Logout. Click any of them, and you will be able to configure the corresponding
function. The detailed explanations for each submenu are provided below.

Time Zone Settings
Choose menu “Maintenance → Time Zone Settings”, you can configure the time on the following
screen.

Time Zone Select - Select your local time zone from this pull down list.

NTP Server Prior - Enter the address for the NTP Server, then the Router will get the time from
the NTP Server preferentially. In addition, for some built-in common NTP Servers, the Router can
get time automatically once it connects the Internet.
 System log
Choose menu “Maintenance → System Log”, you can view the logs of the Router.
System Log : This can enable or disable system log.
Remote IP address : This option can configure system log on Remote syslog server
 Upgrade Firmware
Choose menu “Maintenance → Upgrade Firmware”, you can update the latest version of firmware for
the Router on the following screen.
Click on “Choose File” select the appropriate file and click on upgrade.
Backup / Restore
Choose menu “Maintenance → Backup & Restore”, you can save the current configuration of the
Router as a backup file and restore the configuration via a backup file as shown in bellow figure.
 Backup: This menu is use to save router setting to Backup file. Backup your router setting and
store it to a safe place which can use to recover router setting in future.
 Restore: This menu is use to Restore the backed up settings of your router from the Backup file.
 Factory Default: This menu is use to restore the router settings to factory defaults.


Restart: This menu is use to restart the router from Web GUI menu.
Password
Choose menu “Maintenance → Password”, you can change the factory default user name and
password of the Router in the next screen as shown in figure.
 Diagnostic Tools
You could check all the system logs on “Log Settings”
 Logout
This option can use to logout the router settings.
Product Specifications :
LAN Interface
1 10/100Mbps RJ45 port
WAN Interface
1 10/100Mbps RJ45 port
Power supply
12V-24V,1A (DC/POE)
Antenna
Inner 14dBi antenna
Protection
IP65
Power consumption
9W(Max)
Dimension
95mm x 51mm x 256mm(W x H x D)
Protocol
IEEE 802.11b/g/n
Frequency band
5.180-5.240GHz ;5.745-5.825GHz.
Wireless safety
64/128 bit WEP encryption
RF power
11n:25±1dBm;11a:27±1dBm.
WPA/WPA2、WPA-PSK/WPA2-PSK(TKIP/AES)安
RF mode
2T 2R
Modulation
Wireless speed
Bandwidth
Operation Mode
DBPSK/DQPSK/CCK/OFDM(BPSK/QPSK/16-QAM/6
4-QAM)
802.11n: up to 300 Mbps;
802.11a:54 Mbps(auto-adjust).
40MHz;20MHz
Wireless AP;
Station (CPE):
WDS bridge、 WDS repeater、DHCP
WLAN Interface
Auto choose the best wireless channel/CPE
violation/hide SSID/ ACL access control;
Support point to point, point to multi-point wireless
Availability and Resilience
route.
Auto fail-over/fail-back;
Support
802.3af(Option)/quick setting guide;
SPI fire wall: IP / Port filter/ MAC address filter/ URL
Security Features
filter/protect from Dos attack;
Remote Web access control/WPA/WPA2.
Qos
Support 802.11e, WMM function.
LAN Interface
Frequency Range-MHz
1 10/100Mbps RJ45 port
5.180-5.240GHz;
5.745-5.825GHz.
Gain-dBi
14 dBi
VSWR
≤1.5
Horizontal Beamwidth-°
60°
Vertical Beamwidth-°
15°
Polarization
H& V
Impedance -Ω
50Ω
Maximum Input Power -W
100 W
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. iBall Baton is a registered
trademark of Best IT World India Pvt. Ltd. Other brands and product names are
trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used
to make any derivative such as translation, transformation, or adaptation without
permission from Best IT World India Pvt. Ltd. All rights reserved.
http://www.iBallBaton.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement