Energen P5 USB Charger Power Jumper User Manual

 Compact starter for your trip
User Manual
IMPORTANT SAFETY INSTRUCTIONS
Charge the Power Jumper fully prior to use.
A WARNING: Keep the unit clear of fire and water.
A WARNING: Shock Hazard. Keep away from children. Do not insert foreign objects
into the jumper cables port/jack, the USB output port, or the DC input jack. Do not
expose this product to water, rain, snow, condensation, or spray. Do not open the
Power Jumper to replace the internal battery. No user replaceable parts are inside
the Power Jumper.
A WARNING: Explosion Hazard. Do not use this product where there are flammable
fumes or gases, such as in the bilge of a gasoline-powered boat, or near propane
tanks. Do not use this product in an enclosure containing automotive-type lead-acid
batteries.
The jump start cable clamps must be connected positive to positive (red clip to battery
(+)) and negative to negative (black clip to battery (-)). A reverse polarity connection
(positive to negative) may cause damage to the Power Jumper and/or create a
sparking/explosion hazard.
A WARNING: Fire Hazard
Do not crush or puncture the Power Jumper. Never allow the jump start cables’ red
and black clamps’ metal contacts to touch each other or another common metal
conductor. This could cause damage to the unit and/or create a fire hazard. Always
disconnect the jump start cables from the Power Jumper after each use and store
separately. The jump start feature is designed for short term operation only. Turn the
ignition key for no more than 3 seconds at a time. Operating the jump start feature
for more than 3 seconds may cause damage to the unit. Allow the Power Jumper to
cool down for at least 1 minute after each jump start attempt.
Caution: Operating temperature
Do not expose the Power Jumper to temperatures over +113° F(+45° C)or under -14°F
(-10° C). Using the Power Jumper at high or low temperatures may reduce the internal
battery capacity and shorten the battery life.
Note: In extreme cold weather conditions, please bring the Power Jumper indoors for
best results.
Proper Vehicle Battery Handling Instructions
A WARNING: Explosion and fire hazard
1.
> WON
Follow all instructions published by the battery manufacturer and the manufacturer
of the equipment in which the battery is installed.
. Make sure the area around the battery is well-ventilated.
. Never smoke or allow a spark or flame in the vicinity of the engine or batteries.
. Be careful not to drop a metal object on the battery or allow a metal tool to
simultaneously touch the positive and negative cable ends or battery terminals.
. Remove personal metal items such as rings, bracelets, necklaces, and watches
when working with batteries. Batteries produce a short-circuit current high enough
to weld a ring or other similar objects to metal, causing a severe burn.
. If you need to remove a battery, always remove the negative terminal from the
battery first. Make sure all accessories are off so you don't cause an arc.
. Someone should be within range of your voice, or close enough to come to your
aid when you work near batteries.
. Have plenty of fresh water, soap and a supply of baking soda on hand in the area
of the batteries in case of contact with battery acid. Baking soda neutralizes lead acid
battery electrolyte.
. The Power Jumper is supplied with a rechargeable Li-Cobalt battery.
This battery is self-contained and not consumer replaceable. Battery must be
disposed of properly when it no longer holds a charge. Proper charging practices will
maximize the life of the batteries.
The Energen Power Jumper is a versatile and compact power solution that keeps you charged
and running all day long. In addition to jump starting motor vehicles, Power Jumper can also
recharge your smartphones, mobile gaming devices, portable music players, and other
consumer electronic device. lt is also a high powered flashlight.
How to jump start your car:
Step 1:
A
GC
Make sure the battery is charged more
than 50%.
Step 3:
Connect the jumper cable plug to the
proper socket on Power Jumper.
Remove the jumper cable from Power
Jumper then disconnect the clamps on
the battery terminals.
Step 2:
Connect the jumper cable to the battery
on the vehicle. Connect the red clamp
to the positive (+) terminal, and the black
clamp to the negative (-) terminal.
Step 4:
e
START
Start the vehicle engine.
Note: If the clamps are connected to the wrong polarity terminals on
the battery and you attempt to start the vehicle, the safety fuse will be
blown and the power will be cut off to prevent any injuries and avoid
damaging the vehicle.
Charge a Mobile Device
Step 1: Step 2: Step 3:
у N
USB 5V/2.1A ;
Power
>—
Insert the USB charging cable Insert the other end into your Press the power button on the
into the 5V USB output port. mobile device's charging port. Power Jumper to begin charging.
Emergency Flashlight
Step 1: Step 2:
— N — N
Power Power
SN —
Press the power button. Press and hold the power button Cl) to
switch on the flashlight. Press the power
button (!) again to toggle the flashlight
between normal, flashing, and S.0.S. mode.
Recharge Power Jumper
Step 1: Step 2:
Insert the Power Jumper charging Insert the other end into the wall
cable into the 5V input port. socket charger or the car charger to
begin charging. The battery capacity
indicator lights will begin to flash,
indicating that the battery is charging.
Basic Accessories Products
12V battery clips
Jump starter o USB charge cable
S
mart synthetic leather bag can
A pack all the accessories easily
Ÿ
A/C adapter
Safety warnings
1. Charge the battery for at least 6 hours before the first usage.
2. Never connect red and black clamps together. This may result in physical injury
and damage to the vehicle.
. Never attempt to disassemble the product.
. Do not let the children operate this product without the adult's supervision.
. Store this device in a dry place, away from wet or corrosive environments.
. Do not use this product if the shape of the product appears abnormal or warped.
. Only operate this device under normal operating temperatures.
. Wait at least 15 seconds between jump start intervals.
© O NN V 0/4 D
. Do not attempt to jump start a vehicle when the remaining battery capacity is less
than 10%.
Limited 1-Year Warranty:
For Products Purchased in the U.S.A. :
Energen Electronics \ warrants that its Energen P5 Power Jumper USB Charger, and
the component parts thereof, will be free of defects in workmanship and materials for a
period of one year from the date of first consumer purchase. This warranty may be
enforced by the first consumer purchaser, provided that the product is utilized within
the U.S.A.
Energen will, without charge, repair or replace, at its option, defective USB charger,
products or component parts upon delivery to the Energen Factory Service Department,
accompanied by proof of the date of first consumer purchase, such as a duplicated
copy of a sales receipt.
Exclusions: This limited warranty does not apply:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product, or as a result of unauthorized
alterations or repairs.
3. If the serial number has been altered, defaced or removed.
4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and fitness for a particular
purpose are limited in duration to the length of this warranty.
Energen shall not be liable for any incidental, consequential or other damages;
including, without limitation, damages resulting from loss of use or cost of installation.
Product Service:
For any questions about operating or installing this new Energen product, or if parts are
missing...please contact Energen first.. .do not return this product to the store.
If this product should require factory service, please use www.myenergen.com to
request a RMA number before sending the product. This will ensure the fastest
turn-around time on any repair. If Energen asks that the product be sent to its factory,
the following must be furnished to have the product serviced and returned:
1.
N
For Warranty Repair include some form of proof-of-purchase, such as a photocopy or
carbon of a sales receipt. Make sure the date of purchase and product model number
are clearly readable. If the originals are sent, they cannot be returned.
. Send the entire product.
. Enclose a description of what is happening with the product. Include a typed or clearly
printed name and address of where the product is to be returned, with phone number
(required for shipment).
. Pack product securely to prevent damage in transit. If possible, use the original
packing material.
. Ship prepaid and insured by way of a traceable carrier such as United Parcel Service
(UPS) or Priority Mail with delivery confirmation to avoid loss in transit to: Energen
Service, Energen Electronics Corporation,
17008 Evergreen Place #B, City of Industry, CA 91745 U.S.A.
. If the product is in warranty, upon receipt of the product it will either be repaired or
exchanged depending on the model. Please allow approximately 2 weeks before
contacting Energen for status. If the product is out of warranty, a letter will
automatically be sent with information as to the repair charge or replacement charge.
For any questions please visit us online at www.myenergen.com.