Toshiba TMPM037 FWUG Evaluation Board User manual

TOSHIBA-TMPM037

Document Revision History

Manual Version - 1.0

NGX Technologies Pvt. Ltd TOSHIBA-TMPM037 2 | P a g e

Contents

1. Introduction - TMPM037 ............................................................................................................ 4

2. CMSIS-DAP Debugger and Programming ................................................................................ 4

3. About Us ......................................................................................................................................... 8

4. Company’s Terms & Conditions ................................................................................................. 8

NGX Technologies Pvt. Ltd TOSHIBA-TMPM037 3 | P a g e

1. Introduction - TMPM037

The TMPM037 is an evaluation stamp board which is exploring the complete features of the new ARM Cortex-M0 TMPM037FWUG microcontroller by Toshiba. Based on the ARM Cortex-

M0 core running at 20MHz, the new device operates from a 5.0V supply and a comprehensive set of peripherals and interfaces integrated into a single 64-pin IC.

The 10-bit ADC provides high-speed, PWM-synchronised analogue-to-digital conversion, while an on-board comparator can be used for detecting emergency stop conditions. Other on-board features include a regulator, a single-channel encoder, power-on-reset/low-voltage detection, a watchdog timer and 10-channel 16-bit timer.

Specifications-

 PCB: 2 Layer PCB with FR-4 material

 Power Source: USB Mini with power indicator and on-board linear regulators generate

+3.3V/1A

 Connectors: 1- USB Mini, 1- RS232 Port and 1- 10 Pin JTAG Connector

 Switches: 1- Reset switch and 1- User switch

 LED: 1- Power indicator LED and 2- Test LEDs

 Extensions: Available for all Micro-controller pins

 Dimensions: 63.75 mm x 49.53 mm

2. CMSIS-DAP Debugger and Programming

Steps to configure CMSIS-DAP Debugger.

Step 1: Hardware Setup - Accessories Required:

 Toshiba-TMPM037 stamp board

 CMSIS-DAP debugger

 USB mini cable -2

 20 to 10 pin converter

 10 pin FR cable

Figure 1- Accessories

NGX Technologies Pvt. Ltd TOSHIBA-TMPM037 4 | P a g e

Step 2: Hardware Connectivity

 Using 10-Pin Ribbon Cable connect Toshiba TMPM037 and “20 Pin to 10 Pin

Adaptor”

 Connect CMSIS-DAP debugger to “20 Pin to 10 Pin Adaptor”

 Using USB mini cable connect CMSIS-DAP debugger and computer

 Connect a USB mini cable to power up the TMPM037 board

Figure 2- Hardware Connectivity

Step 3: Open the Keil GPIO_LED project which is downloaded from NGX website.

Step 4: Once Keil GPIO_LED project is opened, in Keil IDE click on Flash toolbar and select

Configure Flash Tools. A Configuration window will be opened as shown below, in which select the tab Device. Now select TMPM037FWUG MCU from the list as shown below

Figure 3- Configuration Window

NGX Technologies Pvt. Ltd TOSHIBA-TMPM037 5 | P a g e

Step 5 : In same Configuration window click the tab Debug Option, under which select

CMSIS-DAP Debugger for the option Use as shown in image.

Figure 4- Configuration Window

Step 6 : To open Target Drive Setup window click Settings button which is highlighted in above image. Here if CMSIS-DAP debugger is recognised it will be shown as below

Figure 5- Target Driver Setup Window

NGX Technologies Pvt. Ltd TOSHIBA-TMPM037 6 | P a g e

Step 7 : Build the project. 0 Errors and 0 Warnings should be there

Step 8 : In Keil IDE, click on Download Code to Flash to flash the code into the board. Once flash is successfully completed, reset the board to verify the GPIO_LED code

Figure 6- Flash Project in Keil IDE

GPIO LED code is verified as shown in the image below.

Figure 7- GPIO LED code verification

NGX Technologies Pvt. Ltd TOSHIBA-TMPM037 7 | P a g e

3. About Us

NGX Technologies Pvt. Ltd is a premier supplier of development tools for the ARM7, ARM

Cortex M0, M3 and M4 series of microcontrollers. NGX provides innovative and cost effective design solutions for embedded systems. We specialize in ARM MCU portfolio, which includes

ARM7, Cortex-M0, M3 & M4 microcontrollers. Our experience with developing evaluation platforms for NXP controller enables us to provide solutions with shortened development time thereby ensuring reduced time to market and lower development costs for our customers.

Our cost effective and feature rich development tool offering, serves as a testimony for our expertise, cost effectiveness and quality.

Contact Details -

NGX Technologies Pvt. Ltd.

#39/39, 'Parusha', 1 st 'E' cross,

5th Main Road, Remco Layout,

Vijayanagar 2nd Stage,

Bangalore – 560 040.

Phone : +91-80-40925507 email:[email protected]

4. Company’s Terms & Conditions

Legal

NGX Technologies Pvt. Ltd. provides the enclosed product(s) under the following conditions:

This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT,

DEMONSTRATION, and EDUCATION OR EVALUATION PURPOSES ONLY and is not considered by NGX Technologies Pvt. Ltd to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL and therefore may not meet the technical requirements of these directives or other related directives.

The user assumes all responsibility and liability for proper and safe handling of the goods.

Further, the user indemnifies NGX Technologies from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all appropriate precautions with regard to electrostatic discharge.

EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL

BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES.

NGX Technologies currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive. NGX Technologies assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein.

NGX Technologies Pvt. Ltd TOSHIBA-TMPM037 8 | P a g e

Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s

Guide prior to handling the product. This notice contains important safety information about temperatures and voltages.

No license is granted under any patent right or other intellectual property right of NGX

Technologies covering or relating to any machine, process, or combination in which such NGX

Technologies products or services might be or are used.

Disclaimers

Information in this document is believed to be reliable and accurate. However, NGX

Technologies does not give any representations or warranties, expressed or implied, as to the completeness or accuracy of such information and shall have no liability for the consequences of use of such information. NGX Technologies reserves the right to make changes to information published in this document, at any time and without notice, including without limitation specifications and product descriptions. This document replaces and supersedes all information supplied prior to the publication hereof.

Trademarks

All referenced trademarks, product names, brands and service names are the property of their respective owners.

NGX Technologies Pvt. Ltd TOSHIBA-TMPM037 9 | P a g e