BT400 G3

Bluetooth Headset

Quick Start-Up

www.bluetake.com

- Overview of BT400 G3 -

1

Volume Down Button

2 Volume Up Button

3 Power/Talking/Pairing Button

4

Ear Hook

5 DC Power In

6

Speaker

7 Microphone

Foldable Microphone

The microphone can be folded up easily when you don't use the headset.

3

- Changing the earhook -

1.

2.

The BT400 G3 Bluetooth headset can be worn on either ear. Please follow the below steps to shift the ear hook for wearing it on the other ear.

1. Carefully remove the ear hook from the headset.

2. Change the direction of the ear hook as shown in diagram 2.

3. Carefully relocate the ear hook to the headset.

3.

4

- Turning the headset ON/OFF -

To turn your headset ON:

Press and hold the button for 5 seconds, and then the speaker will emit two high tones. When the power is ON, the

LED in the button starts to flash blue.

(Note: the headset will enter pairing mode if you press and hold the button for 7 seconds from OFF status.)

To turn your headset OFF:

Press and hold the button for 2 seconds, and then the speaker will emit two high tones. When the power is OFF, the LED in the button will stop flashing.

5

- Charging the battery -

Please charge the battery for approximate 2.5 hours to ensure a fully power while first time using BT400 G3. The LED will turn to be green

when the power is fully charged.

1. Plug the AC power adapter into the DC Jack situated at the back of the headset.

2. Plug the AC power adapter

3. When charging, the LED in the color.

button is on and remains red

4. The LED in the button turns to be green after the battery is fully charged.

5. Remove the AC power adapter from the headset’s AC Power Jack.

Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions

Notice: The headset doesn’t work while it’s charging.

6

- Pairing to a Bluetooth phone -

Please follow the instruction below to pair the headset with a

Bluetooth cell phone:

1. Ensure the headset is OFF.

2. Press and hold the button for approximately 7 seconds until the headset LED starts to flash with blue and red.

3. Release the button when the LED is flashing, the status indicates that the headset is in pairing mode and waiting to pair with another Bluetooth device.

4. Follow the operating instruction for your Bluetooth phone to start a pairing process.

5. The phone’s display will indicate that it found one or more

Bluetooth devices, the “BT400 G3” should be included in the list, please select it for pairing.

6. The phone’s display then prompt you for a pairing passkey or PIN, please enter four zeros “

0000

”.

7. When the pairing process is finished successfully, the headset LED will return to normal status of flashing blue only.

8.

The phone’s display may ask you whether you want to change the headset’s name; you can replace the “BT400 G3” with any name you prefer.

7

- Use the headset -

Answering a call:

After being paired with your cell phone, the headset is now ready to receive incoming calls without handling the phone. When there’s an incoming call, both the cell phone and the headset will ring simultaneously. Upon hearing the ring tones through the headset’s speaker you can answer the incoming call by pressing and then speaking normally.

Ending a call:

You can use either of the ways to end a call:

button

1. Press the headset’s button to end a call.

2. Press the phone’s keypad to end a call.

Making a call:

There are two ways to make calls:

1. Using the phone’s keypad:

As general usage, dial the phone number you want to call by pressing the phone’s keypad. You may also hear the dialing tones through the headset.

2. Using the Voice Dialing through the headset:

What is voice dialing?

Voice dialing is a feature on some Bluetooth phones which

8

allows you make calls by saying the name of the person you want to call. The phone compares your voice with your previous recording (called a voice tag). If they match then the phone will automatically dial the corresponding phone number. Not all

Bluetooth phones support voice dialing, please refer to your phone’s specification to make sure whether your phone supports this feature.

Voice dialing:

The headset does not have a keyboard so it’s necessary to use voice dialing to make calls. To do this you have to record voice tags for the contacts in your phone address book. If your phone supports voice function, you can use this feature with the headset easily. Note that the voice dialing on your phone must be enabled and the voice tags must have been recorded previously. (Please refer to your phone’s instruction on voice recording and storing voice tags.) a. Briefly press the button once. b. After the tone, say the name of the person you want to call. c. The phone number will be dialed automatically by phone after recognizing the correct voice tag.

9

Multi-Pairing:

BT400 G3 supports a particular function “Multi-Pairing”. It allows the headset to be paired with several Bluetooth devices but connected to only one device at a time. The only one basis for multi-pairing is that the last paired device has the highest priority than others.

If the headset is switched on within10 meters of several paired devices, the headset will try to connect to the “1 st

device” within a few seconds.

If the headset can not connect to the “1 st

device”, the headset tries to connect to the second device within a few seconds.

If the headset can not connect to either of the phones, it remains discoverable for other devices for the next xxxxxx minutes, which is displayed by the blinking green indicator light. If you do not make the connection during this time, the headset is switched off automatically.

If you want to use the headset with a paired device that is not a “1 st device” or “last device”, make the connection in your device’s Bluetooth menu.

10

- Troubleshooting -

If you are experiencing difficulties connecting or using your headset, check whether your problem is listed below.

Q: Why can’t I use the voice dialing function after paired the BT400

G3 with my Bluetooth-enabled mobile phone?

A: Please make sure the voice dialing function in your mobile phone is active. Please refer to your mobile phone user’s manual to enable the function.

Q: Why there is an annoying echo when I’m talking by using the

BT400 G3?

A: Please reduce your mobile phone’s volume to eliminate the echo.

Q: Why can not my Bluetooth-enabled mobile phone pair with the

BT400 G3?

A:

1. Please make sure the Bluetooth function in your mobile phone is active.

2. Please make BT400 G3 go into pairing mode again if the mode is timeout.

11

- Specification -

Product Name BT400 G3 Bluetooth Headset

General Radio 2.4 ~ 2.480 GHz ISM

Bluetooth Specification Compliant to Bluetooth specification v1.1

Spread Spectrum

Operating Range

Bluetooth Profile

Antenna Type

FHSS (Frequency Hopping Spread Spectrum)

Class II device; Max. 10 meters in open space

Headset profile, Handsfree profile

Chip antenna

Talking Time

Standby Time

Input Power

Battery Type

Dimension

Up to 10 hours

Up to 350 hours

DC 5V / 500mA

Rechargeable Li-Polymer battery; 3.7V / 160mA

92mm(L) x 50mm(W) x 26mm(H)

Weight 26g

12

http://www.bluetake.com email: [email protected]

13 v040521-1