User Manual - B&H Photo Video

User Manual - B&H Photo Video
BG-C11
BATTERY GRIP
Designed for the Canon
EOS Rebel SL1 DSLR Camera
Introduction
Thank you for choosing the Vello BG-C11 Battery Grip
for the Canon EOS Rebel SL1 DSLR Camera. This camera
accessory offers users the ability to extend camera
shooting time by housing an additional battery for your
device. The grip’s ergonomic design enhances the comfort
of vertical (portrait) image capturing with the verticalshooting shutter release button. The BG-C11 also includes
an IR remote, which can be used to trigger the grip and
camera from up to 15' (4.6 m) away. This grip is compatible
with LP-E12 batteries.
2
Please read
through this entire
manual before using the
BG-C11 battery grip.
The BG-C11 should only be used with compatible
batteries and devices specified in this manual.
2. Cover the power terminals with the contact cap
when the BG-C11 is not in use. This prevents
electrical shorts caused by metal objects touching
the power terminals.
3.
If you notice smoke, an unusual smell, or noise from
the battery pack, discontinue use immediately.
Remove the batteries and take the device to a Vello
authorized reseller.
5.
Remove batteries from the grip when not in use.
6.
Do not attempt to disassemble.
7.
Avoid water or extreme humidity and keep in a dry
and cool place.
8. Keep out of reach of children.
9.
All images are for illustration purposes only.
OVERVIEW
1.
INTRODUCTION
Precautions
4. The battery level may not display properly if the
3
ASSEMBLY
batteries are inserted before mounting the grip.
Battery Grip Overview
7
6
1
2
4
3
5
9
8
11
12
10
13
4
14
7 Contact Cap
Protects metal power contacts.
Keep this cap on when the grip is not
connected to the camera.
3 Integrated IR Receiver
Wirelessly triggers the camera using
the included IR remote and the
battery grip’s integrated IR sensor.
8 Mounting Screw
Connects to the camera’s tripod
socket.
Attachment Wheel
Secures the grip to the camera’s
tripod socket.
9
4 Camera Battery Door Slot
Stores the camera’s battery chamber
door when the grip is mounted.
Anti-Slip Rubber Grip
Provides secure and comfortable grip
when shooting vertically.
5
10 Shutter Release Cable Port
Accepts 2.5 mm to 2.5 mm sub mini
connector of the shutter release
cable.
5
INTRODUCTION
2 Two-Step Shutter Release Button
Serves as an alternate shutter release
button for shooting in vertical
(portrait) mode.
11 On/Off Switch
Turns the grip’s IR receiver and
shutter release button on or off using
the integrated power switch.
12 Battery Chamber Door
Secures up to two Canon LP-E12
batteries in the compartment.
13 Door Latch
Releases battery chamber door.
14 Shutter Release Cable
Carries shutter release signal from
battery grip to the camera.
OVERVIEW
6 Power Contacts
Slides into the camera’s battery
chamber and transmits power.
ASSEMBLY
1 1/4" Tripod Socket
Allows the camera to be mounted on
a tripod when the grip is mounted.
IR Remote Overview
1
2
3
6
1
IR emitter
2
Shutter release button
3
Battery compartment
Vello BG-C11 battery grip
•
User manual
•
IR remote with CR2032 battery
•
One-Year Limited Warranty
•
Shutter release cable
Specifications
Power Source
One or two Canon LP-E12 Rechargeable Batteries
Operating Temperature
32-104°F (0−40°C)
Remote Battery Compatibility
CR2032
Remote Operating Distance
Max. 15' (4.6 m)
Dimensions
4.6" x 2.9" x 3.7" (11.7 × 7.4 × 9.4 cm)
Weight (without batteries)
5.29 oz. (150 g)
7
ASSEMBLY
OVERVIEW
•
INTRODUCTION
Box Contents
Attaching The Grip
1.
With the camera turned
off, op e n the ba t te r y
compar tment door and
remove the battery.
2. Gently
pull the bat ter y
chamber door at a 35° angle
and remove the door from
the camera.
8
3.
Slide the battery
compartment door into the
battery compartment door
slot on the grip so that the
side showing is flat with no
protrusions sticking out.
INTRODUCTION
5.
Rotate the at tachment
wheel counter clockwise
to secure the grip to the
camera.
9
6.
Connect the shutter release
c a ble to the c a mer a’s
shutter release port ( ), and
plug the other end into the
grip’s shutter release port.
OVERVIEW
the grip’s power
contacts into the camera
as shown above. Ensure the
camera’s tripod socket and
the battery grip’s mounting
screw are aligned.
ASSEMBLY
4. Inser t
7.
Insert one or two batteries
into the grip and turn on the
camera. You will be able to
see the battery power level
on the LCD screen.
8. Turn
the battery grip on
using the On/Off switch
to activate the IR receiver
and shutter release button.
Putting the switch in the off
position will disable the IR
receiver and shutter release
button.
10
Note: The Vello BG-C11 can power
the Canon SL1 with one or two
batteries installed in the grip.
Note: When removing the grip,
turn the camera power off, remove
batteries by pressing each side
release, and replace protective
contact cap.
The Vello BG-C11 comes with an IR remote, which can be used to wirelessly trigger your grip and camera from up
to 15’ (4.6 m) away. The use of this accessory requires line-of-sight to communicate. To use the remote, follow these
instructions:
1.
INTRODUCTION
IR Remote
Remove the protective plastic flap from the battery compartment.
3.
Point the remote’s IR emitter at the camera and grip.
4. Press the button on the remote to trigger your camera.
OVERVIEW
2. Make sure the Shutter Release Cable is connected to the camera and grip.
Tip: If your camera’s lens is set to auto-focus, one press of the remote’s trigger button will focus and fire the camera.
11
ASSEMBLY
Note: The included IR remote can also trigger your Canon SL1 without the grip installed. Simply set your camera to
( ) Self-time:10sec/remote Mode. Pressing the button on the remote will trigger your camera.
ONE-YEAR LIMITED WARRANTY
This VELLO product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use
for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s
responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s discretion, of any product
that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall
be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a
model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance.
EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to
state.
To obtain warranty coverage, contact the Vello Customer Service Department to obtain a return merchandise authorization (“RMA”) number,
and return the defective product to Vello along with the RMA number and proof of purchase. Shipment of the defective product is at the
purchaser’s own risk and expense.
For more information or to arrange service, visit www.vellogear.com or call Customer Service at 212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
VELLO is a registered trademark of the Gradus Group. © 2014 Gradus Group LLC. All Rights Reserved.
www.vellogear.com
© Copyright 2014 Gradus Group LLC
All other trademarks are the property of their respective owners.
GG1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising