Quickstart Guide

Quickstart Guide
ALI-IPU5030RMH IP 3MP IR Bullet
Camera Quick Installation Guide
This document guides you through the basic steps to install and initially configure the ALI-IPU5030RMH
camera. The ALI-IPU5030RMH camera features:
•
•
•
•
•
•
•
•
•
•
1/3” progressive scan CMOS
Up to 2048 × 1536 resolution
120 dB WDR, 3D DNR
Smart Codec, Smart IR, Smart VOD
Smart Focus: Motorized VF lens with zoom control
Smart Face Detection
Smart Audio Detection
Intrusion Detection
Defog, EIS, BLC
Built-in heater
What’s in the box
Your camera includes these items:
•
•
•
•
•
•
•
•
Security L-wrench
Video test cable (BNC adapter)
Mounting hardware including screws, wall inserts
LAN drop cable seal kit
Drill template for surface mounting
Adapter plate for gang-box mounting
CD with documentation and the Alibi Discover software utility
This document
Before installing the camera
•
•
•
For more information about the software features of this camera, please refer to the ALI-IP Camera
Software User Manual.
•
•
•
Camera mounting base
Junction box assembly
(see detail below)
Make sure the device in the package is in good condition and all the assembly parts are included.
Make sure all the related equipment is power-off during the installation.
Check the specification of the products for the installation environment.
Make sure the power supply is matched with your required voltage to avoid damage.
Make sure that the wall is strong enough to withstand three times (12 lb) the weight of the camera.
Dust or grease on the lens cover will cause IR reflection. Please do not remove the dome cover film
until the installation is finished. If there is dust or grease on the lens cover, clean the it with a clean
soft cloth and isopropyl alcohol.
Step 1.
Sun Shield
Install a microSD card in the camera
A microSD card installed in the camera provides local storage for log information, capture files, and
recorded video. This information can be downloaded to a network PC by accessing the camera web
interface with Microsoft Internet Explorer (see “Step 5. Remote login” on page 3). microSD cards can be
as large as 64GB. To install a microSD card in the camera:
Articulated
mounting
bracket
1.
Loosen the sun shield set screw, then lift off the sun shield.
2.
Remove the lens cover from the camera body by unscrewing it counterclockwise (observing it from
the lens end).
Camera body
Video test
monitor
cable
connector
Analog video output
Reset button*
Lens
Lens cover
microSD card slot
Cable channel
MicroSD
card slot
with card
partially
installed
Conduit
access
Camera with sun shield removed
* Press the RESET button for 10 seconds when the camera is powering on or rebooting to restore the
default settings, including the user name, password, IP address, the port number, etc.
Safety cable hook
Camera base
locator pins
3.
Insert a microSD card into the slot shown in the photo above.
4.
Push the microSD card into the slot until it clicks into place. See the photo below.
5.
Reattach the lens cover and the sun shield.
Mounting screw
hole (4)
Hole for camera
mounting screw (3)
Top (up)
Cable access
through mounting
surface
Bottom (down)
Conduit port (2)
Junction box detail
1
www.observint.com
ALI-IPU5030RMH_CQ
4/3/15
Step 2.
Install the camera
To mount the camera onto a surface without the junction box
The camera includes hardware to install it directly to the Junction box provided (preferred), to a mounting
surface (without the junction box), or to a 2-gang electrical box using the adapter plate provided. When
using the junction box, camera drop cables can attach to extension cables (for LAN, power, etc.) inside the
box. The camera with or without the junction box can be installed on a ceiling (horizontal surface) or wall
(vertical surface). To install the camera, do the following:
To mount the camera using the Junction box
For this mounting option, the drop cables must be stored behind the mounting surface.
1.
Determine the best fasteners for securing the camera mounting base to mounting surface. The
mounting hardware provided may be suitable for some surfaces.
2.
Remove the junction box from the camera assembly by loosing the four mounting base captive
screws.
3.
Remove the four mounting base captive screws.
1.
Determine the best fasteners for securing the Junction box to mounting surface. The mounting
hardware provided is suitable for most surfaces.
4.
Using the camera mounting base as a template, mark the locations of the holes for the mounting
screws. Also mark the location of a hole for the camera drop cables.
2.
Remove the junction box from the camera assembly by loosing the four captive screws.
5.
3.
Using the Junction box as a template, mark the location of the Junction box mounting screw holes. If
routing extension cables for the LAN, power, alarm devices, etc. through the mounting surface, mark
the location for that hole too. If installing the box onto a vertical surface, observe the orientation for
TOP and BOTTOM orientation markings inside the box.
Route extension cables from the power source and LAN switch (or LAN with PoE), and peripheral
devices for the left (or microphone) and right audio channels, and alarm input and output devices to
the mounting location.
Junction box
To mount the camera onto an electrical box
1.
Install a double-gang electrical box at the location where the camera will be installed.
2.
Attach the adapter plate provided to the electrical box using four (4) screws.
3.
Remove the junction box from the camera assembly by loosing the four mounting base captive
screws.
4.
Attach the junction box to the adapter plate using four (4) screws.
5.
Route extension cables from the power source and LAN switch (or LAN with PoE), and peripheral
devices for the left (or microphone) and right audio channels, and alarm input and output devices
into the electrical box, and then up through the cable opening in the adapter plate and junction box.
6.
Attach the camera safety cable to the safety cable hook inside the junction box.
Mounting surface
Orientation
markings
Mounting screws (4)
4.
Drill holes in the mounting surface for the mounting screws and extension cables (if necessary).
5.
Secure the Junction box to the mounting surface using appropriate fasteners.
6.
Route the network LAN, power, ALARM, RS485, and AUDIO extension cables between the junction
box and the devices they connect to. Do not apply power to the extension cables at this time.
7.
Attach the camera safety cable to the safety hook inside the junction box.
Step 3.
power
Connect camera drop cables to peripherals, LAN and
Cable access
Camera
mounting
base
Terminals
labels
Ethernet connector
(PoE capable)
Safety cable hook
12 Vdc
Power
connector
Safety cable
Safety cable
RS485 (D-, D+)
Audio IN/OUT
Alarm IN/OUT
Camera drop cables to Ethernet, power and peripheral devices
Camera to junction box
mounting screws (4)
Camera
1.
Connect the network ALARM, RS485 and AUDIO extension cables to the camera drop cables as
needed. The camera can connect to an alarm input sensor and an alarm output (reporting) device,
and to one microphone and one audio line out device. The camera can also connect to an RS485
network for control of the lens. Labels on the alarm and RS485 drop cables show where to connect
the extension cable wires.
2.
Connect the Ethernet LAN cable to the camera LAN drop cable. Protect the connection from
moisture and other contamination, if necessary. A weatherproof fitting is provided. Instructions for
using the weatherproof fitting are provided on the web page for the product.
3.
If the camera is not powered using PoE (Power over Ethernet injector), connect the 12 Vdc power
extension cable to the 12 Vdc power drop cable. The power drop cable terminals are labeled + ,
, and -.

CAUTION
2
www.observint.com
Do not apply power to the camera at this time. Before applying power to the camera, ensure that
the polarity is correct. An incorrect connection may cause a malfunction and can damage the
camera.
© 2014, 2015 Observint Technologies. All rights reserved.
4.
Secure the camera to the Junction box (or mounting surface) using the screws provided.
5.
Apply power to the camera through the 12 Vdc power cable or PoE injector, as configured.
Step 4.
Install the Alibi Discover Tool
The Alibi Discover Tool is a software utility used to “discover” Alibi cameras and NVRs/DVRs installed on the
LAN and change their network settings. The tool is provided on the CD with your camera. To use the tool:
1.
Insert the software CD provided with your camera into an optical drive on the Microsoft Windows
computer you will use to access your camera on the LAN.
2.
On the CD, find the folder that contains the Alibi Discover Tool.
3.
Copy the files in the folder to a new directory on your computer. The files should appear as shown in
the directory shown below.
4.
6.
To change the network settings of the camera to be compatible with the subnet where it is installed,
do the following:
a.
3
Modify the network settings to values compatible with the subnet where it is installed.
c.
Enter the admin password for the device in the password field. By default, the admin user
password for Alibi cameras is 1111.
d.
Click the Save button. The new IP address, port, and other settings will appear in the list with
the device you modified.
To open the Alibi Discover Tool, double click the file Alibi Discover Tool.exe. The tool will
automatically discover Alibi cameras and recorders installed on the network.
In the screen shown above, an ALI-IPU5030RMH camera was discovered. This camera, although
installed on a subnet other than the one implied by its IP address is shown, is still found by the tool.
5.
b.
Click the device to highlight it. Notice that the network parameters are populated in the frame
on the right.
www.observint.com
Close the Alibi Discover Tool by clicking the Close icon ( T ) in the upper-right corner of the screen.
Step 5.
Remote login
To access the camera from a computer on the LAN:
1.
Open your Microsoft Internet Explorer browser on your compute and enter the IP address of the
camera in the URL field. In the example below, the IP address of the camera is 192.168.75.76.
© 2014, 2015 Observint Technologies. All rights reserved.
a.
2.
In the login window, enter your User Name and Password in the appropriate fields, then click
Login. The default User Name and Password for Alibi cameras is admin and 1111.
3.
If this is the first time you are logging into a camera at this IP address AND you are using Internet
Explorer 10 or newer, you must configure it for Compatibility mode:
a.
After a successful login to the NVR, a message will appear in the middle of the Live View
window requiring you to load a plug-in. Click on the message to continue, then click Run in
the pop-up block at the bottom of the screen.
Some computer security software may attempt to block you from running WebComponents.exe. If
necessary, open the Internet Explorer downloads list, right click on the WebComponents.exe file name,
then click Run Anyway.
In Internet Explorer, click the Tools icon (located to the right of the tabs), then select
Compatibility View settings from the drop-down menu.
Tools icon
NOTE
b.
b.
In the Setup - WebComponents window opens, click Next to continue.
In the Compatibility View Settings window, ensure that the IP address of your camera is in the
Add this website field, then click Add.
Installing the WebComponents plugin may require that you close the browser. Follow the
on-screen instructions, then restart your browser after the installation is finished.
c.
c.
4.
4
Allow the plug-in installation to complete. When the following window appears, click
Finish.
After clicking Add, the IP address will appear in the Websites list. Click Close.
If this login is the first login to an Alibi camera from your computer and browser, continue with the
following sub-steps to install WebComponents:
www.observint.com
© 2014, 2015 Observint Technologies. All rights reserved.
5.
Open Internet Explorer and log into the camera again. The Live View - Main stream window will
appear.
Live View options
Screen select tabs
Live View image
Logout button
Configurable parameters include:
Microphone, Capture, Record, icons
Step 6.
•
Switch Day and Night: Select either Auto-Switch or Scheduled-Switch.
——
If using Auto-Switch, open the Day/Night Switch submenu to select the Sensitivity,
Filtering Time, and Smart IR feature ON or OFF.
——
If using Scheduled Switch, set the Start Time and End Time of the switch, then open
the Day/Night Switch submenu to select the Smart IR feature ON or OFF.
Also, click the Common, Day and Night tabs to set the Saturation, Hue, Brightness,
Contrast and Sharpness for Day and for Night modes.
•
Image Adjustment submenu: Open the Image adjustment submenu to set the Saturation, Hue,
Brightness, Contrast and Sharpness of the video image. Each parameter can be set to a level of 0
~ 100 either by moving the slider or entering the value in the box on the right. The effect of the
adjustment will appear in the Live View image in the menu.
Exposure Settings submenu: In this submenu, set the following for the best performance:
——
Iris Mode: Select Auto or Manual. Some cameras may not offer both options.
——
Exposure Time: Value ranges from 1/3 to 1/100,000 s. The nominal value is 1/150. Adjust it
according to the lightening condition.
——
Gain: Set the gain to show the optimal brightness level.
Day/Night Switch submenu: You can set the Day/Night switch to Day, Night, Auto, or Schedule.
The option you select determines the submenu options.
——
Day or Night: These options both have one parameter: Smart IR.
——
Auto: If you select Auto switch, you can set the sensitivity (0 .. 7), filtering time and Smart IR.
——
Schedule: Use Schedule to set that Start Time and End Time for the switch. Smart IR is
also selectable.
Backlight Settings: Backlight settings include BLC Area (Off, Up, Down Left Right Center), the
area to control, and WDR (Wide Dynamic Range) ON or OFF.
White Balance: White Balance selection is used to correct colors in the image depending on the
lighting source. You can also set the white balance manually (MWB), using Automatic White Balance
(AWB1), and lock the white balance setting (Locked WB).
Image Enhancement: Options in this submenu include Digital Noise Reduction (DNR) ON or OFF.
If ON, yo can also adjust the level of noise reduction.
Video Adjustment: Video Adjustment includes:
——
Mirror: Mirror adjustment enables you to flip the image (Up/Down), flip Left/Right (reflect
or Center).
Focus, Zoom
controls
Adjust the camera for your surveillance target
To adjust the camera for your surveillance target, you must observe live video from the camera. To do this,
you can either watch the Live View screen from your web browser, or attach a setup monitor with the video
test cable to the video test cable connector on the IR array board.
1.
While observing live video from your camera, unscrew the Pan, Tilt and Rotation lock screws at least
two turns using the security L-wrench provided, then move the camera to point at the center of your
surveillance target. Tighten the lock screws to hold the camera in position.
Tilt
Pan
Rotation lock screw
Rotation
Pan lock screw
Tilt lock screw
2.
Use the zoom and focus controls on the PTZ section of the Live View screen to make Zoom and Focus
adjustments, if necessary. NOTE: The camera features auto focus.
Step 7.
•
•
Setup the video image
The video Display Settings menu includes the image-related configurable parameters for the camera. It
contains several sub-menus such as Image Adjustment, Exposure Settings, Day/Night Switch, etc. that can
be opened or closed for compactness. Additionally, several adjustments can be seen in the Live View image
on the menu. To open the Display Settings menu, go to Setup tab | Image | Display Settings
•
•
•
•
5
www.observint.com
© 2014, 2015 Observint Technologies. All rights reserved..
Rotate: Rotate rotates the image +90 degrees. Rotate and Mirror can be used to adjust the
image in any orientation.
Video Standard: Select 60 Hz for NTSC format.
Capture Mode: To make a complete use of the 16:9 aspect ratio, you can enable the capture
mode when you use the camera in a narrow view scene.
——
——
——
Camera
Image Sensor
1/3” CMOS
Scanning Mode
Progressive Scan
Resolution
Up to 2048 x 1536
Effective Pixels
3.0 megapixel (approx.)
Minimum Illumination
Color: 0.14 Lux (F1.4, AGC On)
B/W: 0 Lux (IR ON)
True Day/Night ICR)
Electronic Shutter (sec)
1 ~ 1/100,000 (Auto/Manual)
Wide Dynamic Range
120 dB WDR
Backlight Compensation
Gain Control
Support
Auto
White Balance Mode
Auto/Selectable
Noise Reduction
3D DNR
IR Illuminators
Smart IR Array, 850 nm
IR Array Range
100 ft (30 m)
IR Sensitivity
700 - 1100 nm
Panning Range
Tilting Range
1 x In
Alarm Ouput
1 x Out
SD Card Slot
1 x micro SD/SDHC/SDXC (up to 64 GB)
Analog Output
1 x Out
Reset Button
Yes
Network
Specifications
Day/Night
Sensor Input
0° ~ 355°
0° ~ 75°
Lens
Lens Type
Motorized Varifocal
Focal Length
2.8 ~ 12 mm
Iris
Auto
Focus
Auto/Manual
Horizontal Viewing Angle
91.2° (Wide) ~ 28.3° (Tele)
F-number
F1.4
Protocols
TCP/IP,ICMP,HTTP,HTTPS,FTP,DHCP,DNS,DDNS,RTP,RTSP,RTCP, PPPoE, NTP,UPnP,SMTP,SNMP,IG
MP,802.1X,QoS,IPv6,Bonjour, ONVIF, PSIA
Security
Password Protection, IP address filtering
Number of Connections
Up to 10
General
Power Requirements
PoE (IEEE802.3af) / 12 Vdc
Power Consumption
12.5 W Max (heater on)
Weight
3.75 lbs
Dimensions
Φ 4.13” H x 12.94” L
operating Temperature
-40 °F ~ 140 °F
Operating Humidity
0% ~ 95% RH, Non-condensing
Ingress Protection
IP66
Color
White
Material
Aluminum (Body) / Polycarbonate (Bubble)
Approvals
CE, FCC, RoHS
System Requirements
Operating System
Windows XP Professional, Windows VISTA, Windows 7, Window 8
Processor
Intel Pentium 4 3.0 GHz or later
Memory
1 GB or above RAM
Display
1024 x 768 resolution or higher
Web Browser
Internet Explorer 6.0 or above, Apple Safari 5.02 or above, Mozilla Firefox 3.5 or above, Google
Chrome 8 or above
Supplied Accessories
CD ROM (User’s Guide, Installation Tools)
Quickstart Guide
Mounting Hardware and Template
Video
Video Compression Format
H.264 (Baseline/Main/High Profile), MPEG4, MJPEG
Codec Streaming Capability
Tri-streaming
Maximum Frame Rate
20 fps @ 2048 x 1536, 30 fps @ 1080p
Bit Rate
32 kbps ~ 16 Mbps
Bit Rate Mode
CBR, VBR
Audio
Audio Streaming
Two-way
Audio Compression Format
64 Kbps (G.711) / 16 Kbps (G.726) / 64 Kbps (MP2L2)
Features
Motion Detection
Support
Event Notification
Alarm Output, Email, FTP
Privacy Mask
Support
Electronic Image Stabilization
Support
Smart Defog
Support
ROI
Support, Up to 4 configurable zones
Video Analytics
Tamper Detection, Intrusion Detection, Face Detection, Dynamic Analysis, De-focus Detection
Interface
6
Ethernet
RJ-45 10/100 BASE-T
Audio Input
1 x In
Audio Output
1 x Out
www.observint.com
© 2014, 2015 Observint Technologies. All rights reserved..
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement