INSTRUCTION MANUAL

MICRO SYSTEM

AM/FM/CD/MP3/USB/SD/AUX-IN/NFC

BT-207

For Customer Use

Enter below the Serial No. which is located

On the bottom of the cabinet. Retain this

Information for future reference.

Mode No.

Serial No.

This“bolt Of lighting” indicates uninsulated material within your unit which may cause an electrical shock.

For the safety of everyone in your household, please do not remove product covering

TO PREVENT

FIRE OR SHOCK HAZARD, DO

NOT EXPOSE THIS EQUIPMENTTO

RAIN OR MOISTURE.

The“exclamation point” calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems.

TO PREVENT

ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT,

AND FULLY INSERT.

Dripping warning:

The product shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,shall be placed on the product.

Ventilation warning:

The normal ventilation of the product shall not be impeded for intended use.

EN-1

PREPARATION FOR USE

Unpacking and Setup

* Carefully remove the unit from the display carton and remove all packing material from the unit itself.

* Remove any descriptive labels that may be found on either the front or top cabinet of the unit. Do not

remove any labels located on either the back or button cabinet of the unit.

* Press the CD door OPEN Button to open the CD compartment door. There is a white card in the CD

compartment which is intended to prevent the CD pickup from moving during shipment of the product,

Remove this card from the CD compartment before use.

Power Sources

Using AC Power

Connect the AC power into Standard household wall outlet. For dual voltage version.

Make sure that the AC VOLTAGE SELECTOR is switched to your local voltage.

BASIC FUNCTION POWER SUPPLY

Using AC Power

1.check if the power voltage, as shown on the type plate located on the bottom of the set,

corresponds to your local ac power supply. if it does not, consult your dealer or service centre .

2.connect the power cord to the ac socket inlet and the wall outlet. the power supply is

now connected and ready for use.

3.to switch off completely, unplug the power cord from the wall outlet.

unplug the power cord from the wall outlet to protect your set during heavy thunderstorms.

Batteries (not included)

Open the battery compartment and insert eight batteries, type R-20, UM-1 or C-cells,

(preferably Alkaline) with the correct polarity as indicated by the + and - symbols inside the compartment.

Batteries contains chemical substances, so they should be disposed of properly

Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Therefore:

Do not mix battery types: e.g. alkaline with carbon Zinc. Only use batteries of the same type for

the set. When inserting new batteries, do not try to mix old batteries with new ones.

Remove the batteries if the set is not be used for a long time.

EN-2

FIG

4

2

3

1

5 6

7

8

9

10

11

1213 14 15

IR

16

17

18

20 19

21

19

25

22 23

1.

EQ BUTTON

2.

MUTE BUTTON

3. PLAY/PAUSE BUTTON

4. STOP/USB/SD BUTTON

5. REMOTE SENSOR

6. STANDBY INDICATOR

7. POWER BUTTON

8. TIME/PROGRAM BUTTON

9. PRE- DN BUTTON

10.PRE- UP BUTTON

11.REPEAT/MO/ST BUTTON

12.FUNCTION BUTTON

13.LCD DISPLAY

24

14.RANDOM/BAND BUTTON

15.VOLUME BUTTON

16.BASS BUTTON

17.

BACK/NEXT KNOB

18.

AUX/PHONES/USB/SD DOOR

19.LEFT&RIGHT SPEAKER BOXES

20.FM ANTENNA

21.BATTERY DOOR

22.SPEAKER WIRE CONNECTOR(R)

23.SPEAKER WIRE CONNECTOR( L)

24. AC SOCKET

25.CD DOOR

EN-3

Top and front panels(See fig 1 )

1.EQ BUTTON

-Press the button to change EQ CD/MP3/USB/

SD/AUX/RADIO's music style.

-When playing the music, push down this button is in the popular-jazz-FLR-classica-rock.

2.MUTE BUTTON

13.LCD DISPLAY

- Show the song playing time.

- Show the FM dial frequency.

14.RANDOM/BAND BUTTON

- In a CD/MP3 / USB/SD mode, press this button can be played at random.

-Press the mute button allows CD / MP3 / USB

/SD/ AUX / the RADIO to enter the mute state.

3.PLAY/PAUSE BUTTON

- Start or pause MP3/CD/USB/SD/BT play.

-In radio mode, press the play/pause button

enter the automatic channel scan mode.

4.STOP/USB/SD BUTTON

- Stop CD/MP3/USB/SD playback;

erase a CD program.

- Press and hold more than 1.5 sec change USB1.1/SD media(only USB).

5.REMOTE SENSOR

6.STANDBY INDICATOR

7.POWER BUTTON

-Press POWER button on.

8.TIME/PROGRAM BUTTON

- The radio in the mode, press this button to select the FM STEREO, FM , AM.

15.VOLUME BUTTON

- Adjust volume level.

Rotate the volume button to hold the CD/MP3/

USB/SD/AUX/BT/RADIO the volume.

16.BASS BUTTON

-Press the BASS button can make the CD/MP3/

USB/SD/AUX / RADIO into the BASS state.

17.BACK/NEXT KNOB

BACK

-To setup the time standby state

BACK track selection.

- Rotate and hold more than 1.5 sec BACK

search intra track.

-In standby mode, to setup the time of the unit.

-program and review programmed track numbers.

-In the working status, push down this button

- In the radio mode, Rotate BACK will enter

the low end of the manual channel scan mode.

NEXT can on CD/MP3/USB/SD/RADIO for programming.

9.PRE-DN BUTTON

-To setup the time standby state

NEXT track selection.

- In the radio mode, - Rotate and hold more than 1.5 sec

press PRE-DN button to choose the back channel. forward search intra track.

- In the mp3 mode,

- In the radio mode, Rotate NEXT will enter

Press PRE-DN button to enter the back folder.

the high-end manual channel scan mode.

10.PRE-UP BUTTON

18.AUX/PHONES/USB/SD DOOR

-In the radio mode,

-The built-in AUX/PHONES/USB/SD jack.

press PRE-UP button to choose the next channel.

19.LEFT&RIGHT SPEAKER BOXES

-In the mp3 mode,

20.FM ANTENNA

press PRE-UP button enter into the next folder.

- To improve FM reception.

11.REPEAT/MO/ST BUTTON

21.BATTERY DOOR

- Repeat a track CD/MP3/USB/SD program.

-To open battery compartment.

- Repeat mode : normal->repeat 1->repeat all->

22.SPEAKER WIRE CONNECTOR (R)

repeat album ->normal.

23.SPEAKER WIRE CONNECTOR (L)

- Press MO/ST button once, to mono state.

24.AC SOCKET

- Press MO/ST button twice, to stereo state,

- Inlet for power cord.

stereo is displayed (In FM mode).

25.CD DOOR OPEN BUTTON

12.FUNCTION BUTTON

- Press here to open/close the CD door.

- Select source of sound CD/USB(SD)/BT/

AUX/RADIO.

EN-4

Remote Control

1

2

5

6

9

10

13

14

17

12

11

16

15

8

7

4

3

19

18

1. POWER BUTTON

2. OPEN/CLOSE BUTTON

3. INTRO BUTTON

4. MUTE BUTTON

5. RANDOM BUTTON

6. P- UP BUTTON

7. REPEAT/MO/ST BUTTON

8. PROGRAM BUTTON

9. BACK BUTTON

10. FUNCTION BUTTON

11. NEXT BUTTON

12. EQ BUTTON

13. PLAY/ PAUSE BUTTON

14. P- DOWN BUTTON

15. BBS BUTTON

16. STOP/BAND BUTTON

17. NUMBER KEY

18. VOL- BUTTON

19. VOL+ BUTTON

RANDOM BUTTON

-In the player CD/MP3/USB/AUX , press the RANDOM button can be played at random.

Press again to cancel.

BBS BUTTON

-In the player CD/MP3/USB/BT/AUX/RADIO, press the BASS button can make into the bass state. Press again to cancel.

EQ BUTTON

-In the player CD/MP3/USB/BT/AUX/RADIO, press the EQ button to change music style.

-When playing the music, press this button is in the classica-rock-popular-jazz-FLR.

MUTE BUTTON

-In the player CD/MP3/USB/BT/AUX/ RADIO, press the MUTE button to enter the mute state.

Press again to restore volume.

INTRO BUTTON

-In the player CD/MP3/USB,press the INTRO button into 10 seconds browsing repertoire state, press again cancel browse.

* Please pull out the plastic paper from the battery door before use the remote control.

* When the remote control operation becomes unstable or the distance from which the

remote control works is shorter. replace the batteries with new ones.

* Using the remote control unit

To use the remote unit, point at the REMOTE SENSOR and press the buttons gently and firmly. Remote control operation is possible within approximate 18ft (6m). However, since the remote control range is less when the unit is used at an angle, use directly in front of the REMOTE SENSOR, for maximum distance.

Do not expose the REMOTE SENSOR to strong light (direct sunlight or artificial lighting) and make sure that there are no obstacles between the REMOTE SENSOR and the

remote control unit.

USE CLOCK

to setup the time of the unit

1. connect the ac on( The following operation must be in standby mode) .

2. short according to the time button, the time will flashing on the lcd display.

3. Rotate BACK、NEXT to select the number of the time. you can setup the time format by

12h or 24h.

4. press time button to confirm.

5. then you can set the hour and the minute with the same method of steps 3- 4.

6.

after setup the unit time, long press the time button can setup the unit begin working time , with the same method of steps 3- 4.

Note: after setup the beginning time, the lcd will display the radio/cd/usb/sd/aux/blue mode,

Rotate the BACK or NEXT to choose the mode, then it press time button to affirm, otherwise it playusb or aux mode first.

Radio reception

1.

Press FUNCTION button select RADIO mode .

2 .Press BAND to select the desired wave band: FM STEREO, AM, FM, FM ST.

3.Tune to required station by Rotate BACK/ NEXT or press PRE- DN / PRE- UP.

Manual Tuning: Rotate BACK or NEXT and then release within 1 sec.

Auto Tuning: Press the play/pause button enter the automatic channel scan mode, and to be put automatically sets.

Preset Channel:(FM 30 Preset memories, AM 10 preset memories )

(1) Rotate BACK/ NEXT Select desired station.

(2) Press PROGRAM button once , The MEMORY number indicator begins steady

in the display.

(3) Press PRESET-UP OR PRESET- DN buttons to select the desired number.

(4) Press PROGRAM button to save that station.

(5) Repeat steps (1) to (4) procedures for other stations.

4.After end of program. press PRE-UP or PRE-DN to start play the frequency that you

selected or Press number key on the remote control.

5.

Rotate [VOL-]or [VOL +] to adjust the volume.

6.Extend TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting.

7.Turn off the radio by press FUNCTION button select other mode or press power button

to off the unit.

8.Switch on again after shut down, the memory frequency still exists.

MONO/STEREO

-Press MO/ST button once, to mono state.

-Press MO/ST button twice, to stereo state, stereo is displayed.

EN-6

PROGRAM METHOD

(1)Press the [PROGRAM] key at STOP mode, system will go to PROGRAM mode.

-The PRG icon and P01 will blink at 2Hz. This prompts the user to enter the first

songs in the program PLAY list.

(2)The user can select the desire tracks by using [NEXT], [BACK] keys.

Once these keys are pressed, the Display will show the selected track.

(3)After select the desired track, press [PROGRAM] key again and it will be stored in

the memory. Mp3 Maximum 99 and CD Maximum 20 tracks can be programmed

when Repeat steps (2) to (3) procedures.

(4)If press the [STOP] key during the program mode, then the selected TRACKs will be

stored in the memory and return to STOP mode (Continuous Play mode)

(5)If press the [PLAY] key during the program mode, it will start the program PLAY mode.

PLAY start from P01 Track

Erasing a program

You can erase the content of the memory by:

- While playing, press STOP button twice.

- Opening the CD door

- Select the other mode.

USE AUX

To listen music with a mp3

、 discman

、 walkman

.

1. Connect to the AUX .

2. press function selector to AUX, the sound source of the mp3 or discman or walkman will output from the unit.

-Rotate the volume control to adjust the volume.

-The unit can't control the player.

EN-7

CD/MP3 PLAYER

CD/MP3 Player

Playing a CD/MP3

USB/SD Audio functions

This CD-player can play Audio Discs,MP3 CD-R.

1)press function button or stop/usb/sd button to

Do not try to play CD-ROM,CDi,VCD,DVD or computer CD.

choose the usb or sd state.

1.

Press function button to CD state.

2) PLAY/PAUSE

2.to open the cd door, press cd open button.

3.insert a mp3/cd or cd-r 、with the printed side

3) NEXT, BACK Skip search

4) Program Track(MP3 99 Track, CD 20 Track )

facing up and press cd door gently to close.

5) REPEAT MODE : normal->repeat 1->repeat all->

4.press play/pause on the set to start playback.

repeat album ->normal

5.

Press the pause button to pause play, press the play button back playing.

6) Maximum Folder : 99 Folders

6.to stop cd playback , press stop.

7) Maximum File : 999 Files note: cd/mp3 play will also stop when: -Press and hold the [STOP] key more than 1.5sec

-you open the cd compartment;

-you select radio sound source;

at USB mode , system will change to SD mode.

Then “SD“ will be display. At this moment,

-the cd/mp3 has reached to the end.

selecting a different track.

system will read the SD .

during playback you can use back or next to select a particular track.

- If a device is successfully read, then the

correspond device is ready to play a file.

if you have selected a track number in the

- If a device fails to be read, then “NO” will

stop or pause position, press play to start

playback.

be appeared on the Display to indicate that there

is no device .

Rotate next once briefly for the next track,

or press repeatedly until the desired track

*Notice : If no device is attached or the player

number appears in the display.

Rotate back once briefly to return to the

fails to read the device when a user switch over

USB to SD with pressing [STOP] key,

beginning of a current track.

Rotate back more than once briefly for a

then “NO” is displayed and the system moves

into the STOP mode.

previous track.

finding a passage within a track

-When the unit has not the disc, inserting the

1.Rotate and hold down back or next.

the cd is played at high speed.

usb/sd card will automatically real usb/sd card,

it read the USB first while having the USB.

2.when you recognize the passage you want

-The unit don’t support the HDD all and the portion release back or next.

normal playback resumes.

usb with mp3 player.

Note: at the mode of CD/MP3 / USB/SD,the lcd will different play modes:repeat

repeat-play the current track continuously.

display the number of song or the song playing time.

repeat all-plays the entire cd continuously.

playing tracks in random order after press the random button, the tracks will be played in random order.

EN-8

EN-9

USE NFC

Press FUNCTION button select to bluetooth mode. Search bluetooth equipment ”BT-207" math connection, such as need to enter pass word for “0000".

1. Press PLAY/PAUSE button to play or pause playback.

2. Rotate [VOL-]or [VOL +] to adjust the volume size.

3. Rotate BACK or NEXT to select tracks.

NOTE: Bluetooth effective receiving distance of about 10M,different bluetooth devices may be slightly different operation, please read carefully before operation you use the bluetooth device

(IPHONE, IPAD,MOBILE PHONE, ETC.) Instructions.

NFC(Near Field Communication) function for Phone or Tablet

First, press FUNCTION button to select bluetooth mode.

If your phone(tablet) support NFC, first turn on bluetooth NFC working mode, and confirm setting

“Allow data exchange when it torches another device”.

Move your phone(tablet) to near this unit(USB-92) no more than 10CM, or lightly touch the NFC sensor area.

When hear a sound “Di Da” from the USB-92 that means connect success. Then you can play the music through the USB-92 from your phone(tablet).

NFC

OPEN/CLOSE

EN-10

No CD/MP3 inserted

Insert a CD,MP3, CD-R.

- CD-R、is blank or the disc is

not finalized

Use a finalized CD-R.

CD/MP3/ USB/ SD playback does not work

CD/MP3/ USB/ SD badly scratched/dirty

Replace/clean CD/MP3/ USB/ SD

(see maintenance)

The CD/MP3 skips tracks

CD/MP3 damaged or dirty

Replace or clean CD/MP3

TECHNICAL SPECIFICATIONS

GENERAL

Power Requirement ............................................................AC 120/220V~50/60Hz

Power consumption .............................................................AC 20 Watts

Dimensions......................................................Appro.434 mm(L)x214 mm(W) x228 mm(H)

Operation temperature.........................................................+5°C - +35°C

RECEIVER SECTION

Receiving Bands...................................................................AM/FM

Tuning Range..........................................................AM: 530-1710kHz

FM: 88-108MHz

AUDIO SECTION

Power output .........................................................................Maximum 3 Watt x2

Headphone Impedance ............................................................4 ~ 32 Ohms

ACCESSORIES

Instruction Booklet.....................................................................1

Remote control..........................................................................1

Ac line cord...............................................................................1

EN-11 EN-12