Zebora YSW 10 Wireless Camera

Quick Setup Guide

Email: [email protected]

1

Cellphone/Tablet Setup

*Must be the �irst step to connect the camera with Wi-Fi.

1. Make sure your cellphone/tablet is connected with Wi-Fi.

2. Search “Yoosee” App from Apple Store (for iOS user) or Play Store

(for Android user) and install in your cellphone/tablet. Register an account and log in. (Other android users, just go to www.zeboragroup.com

“Download Center ” to download the “software for android”)

3. On the top right corner, click “+” and choose “Smartlink”. Now plug in your camera and wait for 20 sec until you hear “Di-Di-” from the

camera (Must hear the voice before next step). Click “Next”.

4. Manually input the Wi-Fi password correctly (*in case, if you choose the default wireless password, make sure to delete an empty space at the end). Click “Next”.

5. You will hear “Ding” once the camera detects the Wi-Fi. About 25 sec,

“Setting Success” pops up. Click “Ok”, and camera ID pops up.

6. Please input camera password “123”. Click “Save”. Your camera now is connected to Wi-Fi. Click image icon to play video. Swipe the screen to control the camera remotely.

**If the Wi-Fi connection failed, reset the camera: press the reset button for 5 sec. After 30 sec, you will hear “Di-Di-”, then repeat step 3 to 6.

2

Add an Online Camera

Two conditions to add an online camera:

1. Add an online camera to a

second device

: you must register another

Yoosee account. Make sure one Yoosee account is for one device only.

2. Your camera is online, but you delete the APP or the camera from your Yoosee account.

How to add an online camera

Log in Yoosee account:

* If the device connects with the same Wi-Fi as the camera. “Discover 1

new device” pops up, click it and input the camera password (If you

don’t reset password, it is “123”). Click “Save” to add the camera to your

Yoosee device list.

* If your device does not connect with the same Wi-Fi as the camera. You

can click “+” on the top right corner, choose “Manual” to add the camera.

Input a camera name, the camera ID(located at the bottom) and camera

password. Click “Save” to add the camera to device list.

3

PC (Windows only) Setup

*You can only set up the PC after your camera is connected to Wi-Fi.

1. Go to www.zeboragroup.com, in “Download Center>>App Download”, download CMS for Windows PC (Not Mac) and intall it. Click “CMSClient” icon on your desktop.

2. You can choose one of the two Login types:

*Remote Login: use your cellphone/tablet Yoosee account (recom’d)

*Local Login: User: admin (case sensitive)

Password: 00000000 (Eight “0”)

3. After log in, click on the left to add device, then input your camera

ID next to the 3C ID. The camera ID is located at the bottom of the camera (7 digits). Input your camera password (If you don’t reset the password, it is “123”). Change the device name (Optional). Click “OK”.

4. Double click the device name under the device list on the left panel to start or stop connecting to your camera. Click the four arrow panel on the left to control the camera.

*If you cannot connect your camera in current login mode, just log out

and choose another login type.

5. There are multiple monitor screens. One screen is for one camera.

Double click to get full screen, and double click again to return.

4

Video Record Setup

For Cellphone/Tablet

*You need to have a micro SD card, it supports up to 64GB.

1. Insert the SD card into the slot behind the camera.

2. Open “Yoosee”, click the camera name, and “ Playback, Settings, Edit ” pops up:

3. Click “Settings” >>Date and Time. Set the camera “date and time” to your local date and time, click “Apply”; Set the “Timezone” to your local timezone (refer to Page 9), click “Apply”. Go to “Storage info” to “Format/Erase SD card”.

4. Remove the SD card and insert again (

Very important step

).

5. Click “Settings”>>Record Settings”, turn on “Record Switch”.

6. Click “Playback”, you can play the recorded videos after 30~60 min

(Video will be saved automatically in “Playback” every 30 min).

For PC

*No micro SD card needed for recording.

1. Log in CMSClient, click and change the “File Save Path” for video recorded. Find the �ile where you saved the videos and play.

2. On the top panel of the video screen, you can choose the icon for “talking, recording, snapshot” (from left to right).

5

Motion Detection Setup

Open “Yoosee”, click camera name, “Playback, Settings, Edit” pops up:

Click “Settings”. Turn on “Receive Alarm” and “Motion Detection”. If you need camera alarm, turn on “Buzzer”. Go back to device list, click and switch to . Now motion detection has already set up.

* alarm; disalarm.

Camera Password Change Setup

Go to Settings >> Security Settings>>Admin Password to set up a new password for your camera (Highly recommend)

Two-way audio

In your real-time video streaming, you will see the lower banner

*Press and hold for talking

6

1. Make sure your cellphone/tablet is connected with Wi-Fi.

2. Search “Yoosee” App from Apple Store (for iOS user) or Play Store

(for Android user) and install in your cellphone/tablet. Register an account and log in. (Other android users, just go to www.zeboragroup.com

“Download Center ” to download the “software for android”)

3. On the top right corner, click “+” and choose “Smartlink”. Now plug in your camera and wait for 20 sec until you hear “Di-Di-” from the

camera (Must hear the voice before next step). Click “Next”.

4. Manually input the Wi-Fi password correctly (*in case, if you choose the default wireless password, make sure to delete an empty space at the end). Click “Next”.

5. You will hear “Ding” once the camera detects the Wi-Fi. About 25 sec,

“Setting Success” pops up. Click “Ok”, and camera ID pops up.

6. Please input camera password “123”. Click “Save”. Your camera now is connected to Wi-Fi. Click image icon to play video. Swipe the screen to control the camera remotely.

**If the Wi-Fi connection failed, reset the camera: press the reset button for 5 sec. After 30 sec, you will hear “Di-Di-”, then repeat step 3 to 6.

Troubleshootings

Part 1: About Network Connection

Q: why it shows “of�line” when I open the App?

A: 1. Check if your camera is plugged in or Wi-Fi is connected .

2. Pull the “device list” page and hold for seconds to re�lesh the page.

3. Delete the camera, and manually add the camera again.

Q: Why I cannot connect the camera to Wi-Fi in camera setup?

A: 1. Make sure you input the correct wireless password;

2. Check if your router is 2.4 GHz but not 5.0 GHz, this device only

supports 2.4 GHz. If your router is 2.4 GHz and 5.0 GHz swichable,

contact your router carrier to turn off 5.0 GHz.

3. Make sure you start to connect Wi-Fi during the beep “Di-Di-”;

4. If the above steps still don’t work, please reset and reconnect your

camera. Please also refer to Page 2 of Wi-Fi connection.

Q: After connect with my second cellphone to the camera, why does one of the cellphones show “of�line”, or “ID busy”?

A: Both of the cellphones may share the same account to login, make

sure one cellphone/tablet should use one account. Please go to

Account Login page to register a new account. If you see “error 6”

during registration, it means that the account has been taken.

7

Q: There is a red exclamation mark , I cannot connect to camera.

A: Click the icon, if it becomes , then you can connect to the camera.

But if it shows Device password error, click camera name and choose

“Edit”, input the correct camera password (If you don’t reset password,

it is “123”); if it shows Network error, reset your router. (When you see

Network error, it is because too many wireless networks interfere while

lots of devices are using the Wi-Fi. The wireless may exist around your

area.)

Part 2: About SD Card Video Recording

Q: I format the SD card, why I cannot turn on “Record Switch”?

A: 1. Format the SD card on cellphone/tablet Yoosee (Settings>>Storage info

>>format/erase SD card). Make sure SD Remainder Capacity is not “zero”.

2. You should remove the SD card and insert again. The record light

should be on before you turn on the “Record Switch”. (if you still cannot

turn on “record switch”, just eject and insert the card again).

3. or you can keep the card in the slot, but unplug the camera and plug in

again. Then you can turn on “Record Switch”.

8

Q: Why I cannot �ind the recorded video in “Playback”?

A: You should Set the camera time to your local time/date and

zone (Setting >> Date and Time Settings). This will help you

capture the video

synchronously when you record videos. Here

is Timezone for your reference.

Time zone in US &CAN UTC Offset UTC Offset

(Standard Time) (Daylight Saving Time)

Newfoundland (NST) UTC-3 UTC-2

Atlantic (AST) UTC-4 UTC-3

Eastern (EST) UTC-5 UTC-4

Central (CST) UTC-6 UTC-5

Mountain (MST) UTC-7 UTC-6

(*N/A for AZ)

Paci�ic (PST) UTC-8 UTC-7

Alaskan (AKST) UTC-9 UTC-8

Hawaii-Aleutian (HST) UTC-10 UTC-9

Samoa (SST) UTC-11 UTC-11

Chamorrow (ChST) UTC+10 UTC+10

Time zone in EU UTC+1 UTC+2

9

Q: My SD card is in the slot, why I cannot open “Storage info”?

A: Eject the SD card and insert again.

Q: The camera stops recording, and I can’t format the SD card either on

Yoosee or computer, why?

A: It is probably that your SD card is defective.

Q: How can I delete the video if the SD card is full？

A: The SD card can be overwritten if it is full. You can also delete it

manually. Turn off the “Record Switch” in “Record Settings”, then go to

“Storage info” to “formart/erase SD card”.

Part 3: About PC Settings

Q: Can I play the video in SD card (in camera) through CMSClient on PC ?

A: Yes. Log in CMSClient using remote login mode. Click the “Playback” icon. In “Record �ile type”, choose “remote record �ile”. Select the camera where your SD card locates in. Input the begin and end recording time.

Then click “Search”, and you can view the SD card records.

Q: I can log in CMSClient on PC, but I cannot connect to the camera.

A: 1. Make sure that you input the correct camera password.

2. If you cannot connect the camera, just select another login mode to

add your camera.

10

Q: Why the camra is video recording when I start monitoring on CMS?

A: Just click , and select “Close” for Auto start record when monitoring.

Part 4: About Camera Settings

Q: Why can’t I change camera settings？

A: Because your “Yoosee” is not connected with the camera. Only when the

communication of camera and Yoosee is in good condition, you can

change the camera settings. Please pull the page of device list to refresh.

Q: How can I change the camera password？

A: You can change it in “Settings>>Security Settings>>Admin password”.

You can also set a guest password, so that people can use this password

to add your camera to view the video, but they can’t change the camera

settings.

Q: How can I side up the image if I install the camera on ceiling?

A: Just click “Settings>>Media Settings”, turn on “Images Reverse”.

11

About Zebora

Zebora Group Corp headquaters in Boston, MA. It is a growing company with a US registered trademark by the United States Patent and Trademark Of�ice

(USPTO). Zebora focuses on providing state-of-the-art household smart products that are company branded. Our aim is to make your life easier and more intelligent.

The focus of Zebora Group is to create and develop up-to-date intelligent products for every day uses. We have currently produced a series of high resolution surveillance cameras such as YSW15 (ZQF510), YSW8, and YSW10.

In the Zebora community, our customer service and technical support team will always be there for you. We promise, all the cameras you ordered from

Zebora are one year warranty! Your satisfaction and the high quality of our products is our No. 1 priority. Zebora Group provides people and products you can count on!

contact us:

Email: [email protected]

Phone: 1-978-905-9345 (US, EST 10AM-6PM)

Website: www.zeboragroup.com

12