BEC 8920NE

Ultimum

®

The Ultimate Residential Gateway

VDSL2/ADSL2+/Bonded/FTTH

Quick Start Guide

Version 1.0

BEC 8920NE The Ultimate Residential Gateway

PLEASE READ THE QUICK START GUIDE AND FOLLOW THE

STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU

INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.

IF YOU NEED MORE INFORMATION ON THIS SOFTWARE

CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON

CD-ROM.

Package Contents

 BEC 8920NE The Ultimate Residential Gateway

 RJ-45 Ethernet Cable

 Y-Cable for xDSL bonded operation

 Two wireless detachable antennas

 Power adaptor

Warning

Attention

1



 Do not use the router in high humidity or high temperatures.

 Do not use the same power source for the router as other equipment.

 Do not open or repair the case yourself. If the router is too hot, turn off the power immediately and have it repaired at a qualified service

center.

 Avoid using this product and all accessories outdoors.

 Place the router on a stable surface.

 Only use the power adapter that comes with the package. Using a

different voltage rating power adaptor may damage the router.

Quick Start Guide

Front Panel LEDs

LED STATUS DESCRIPTION

Power (PWR)

Green

Off

System is up and ready

Device has no power.

Green LAN port is connected to an Ethernet device

Ethernet (ETH)

Port 1 - 3

Blinking Data being transmitted/received

Off No device is connected to the Ethernet port

This is a Gigabit LAN Ethernet port.

Gigabit

Ethernet

Port 4

Green

Blinking

BEC 8920NE is successfully connected with a broadband connection device.

Data being transmitted/received

Off No device is connected to the Ethernet port

Gigabit

Ethernet WAN

(EWAN)

WAN port for broadband connectivity

Green BEC 8920NE is successfully connected with a broadband connection device.

Green Wireless connection established

Wireless

(WLAN)

Blinking Data being transmitted / received

Off

Green

Wireless being turned off

Wireless device(s) being connected successfully via WPS mode

WPS Blinking

Off

Green

WPS is enabled and trying to establish a WPS connection.

WPS being turned off

Successfully registered and ready to be used.

DSL1 / DSL2

Orange

Green

Phone is off-hook, in-use

IP received and traffic is passing thru the device.

Internet (INET) Blinking

Off

Data being transmitted / received

BEC 8920NE is either in bridged mode or WAN/DSL connection is not ready.

2

BEC 8920NE The Ultimate Residential Gateway

Rear Panel Connectors

2 3 4 5 6 8 9

0

1 1

0

7

1

PORT

Antenna

2 DSL

MEANING

Screw the supplied Wi-Fi antennas onto the antenna connectors on both sides.

Connect the device to an ADSL/VDSL telephone jack or splitter using a RJ-11 telephone cable

Connect to Fiber/ Cable/ xDSL Modem with a RJ-45 cable 3 Gigabit EWAN

4

Gigabit LAN

Ethernet (ETH4)

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when connecting to a PC or an office/home network of 10Mbps /100Mbps /1000Mbps

5

LAN Ethernet

(ETH 1~3)

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when connecting to a PC or an office/home network of 10Mbps /100Mbps.

6 USB

USB function is not available

7 Reset

Press the reset button to restore to factory default settings (this is used when you cannot login to the router, e.g. forgot your password)

8 Power ON/OFF Power ON/OFF switch

9 Power (PWR) Connect the supplied Power Adapter to this port.

* Note: 1. For WPS configuration, please refer to the WPS section in the User Manual.

3

Hardware Connection xDSL Connection – Single Pair

Quick Start Guide

xDSL Connection – Bonding

4

BEC 8920NE The Ultimate Residential Gateway

FTTH / Broadband Connection

Hardware Installation

1. Power Connection

Plug in the supplied power adapter to the wall jack, the other side to the 8920NE then power

ON the 8920NE by pressing the Power On/Off button.

2. LAN Connection

Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to the PC ’s Ethernet interface.

5

Quick Start Guide

3. WAN Connection

3.1 xDSL Interface

For single line xDSL, please connect a RJ-11 to the DSL port , and the other side to the phone jack on the wall.

For bonded xDSL, please connect the supplied Y-cable to the DSL port, and the other two ends to the phone jacks on the wall.

3.2 EWAN Interface

Connect RJ-45 Ethernet cable to the EWAN port, and connect the other side to another alternative broadband device, such as Cable Modem, VDSL, Fiber Modem or PON optic lines. <Please refer to User Manual for detailed instruction.>

6

BEC 8920NE The Ultimate Residential Gateway

4. USB Connection

FTP or Samba Server attached to the USB port. Simply plug in an external USB HD and do a setup in the GUI. <Please refer to User Manual for detailed instruction.>

7

Quick Start Guide

Connecting to the Router

The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached

PC to this router is in the same subnet and has an IP address in the range between 192.168.1.1

~ 192.168.1.253.

Open a web browser and type http://192.168.1.254 in the URL address bar.

URL Address bar: type http://192.168.1.254

The login prompt will appear. Input the default username (admin) and password (admin) for

Account type, Administrator.

*This username / password may vary by different Internet Service Providers.

Quick Setup Your Router

phone jacks or with your Internet box or fiber line.

Step 1: WAN Connection Setup

Select the primary network interface for your Internet connection, xDSL/FTTH mode.

Step 2: Internet Connection Setup

Next to Type, select your Internet connection and fill out all of the appropriate fields.

Step 3: Connection attempts to the Internet

Wait for 10 - 20 seconds for the Gateway to establish an Internet connection.

Step 4: Internet connection established

“Congregations!” message will be shown if the Internet connection is ready to go.

8

BEC 8920NE The Ultimate Residential Gateway

Step 5: Setup Wireless Connection

Setup the SSIDs and change the Security Passphrase to secure your wireless network.

Wireless Service: select Enable

SSID: Assign an unique name

Network Authentication: select a mode

- WPA-PSK

1.

2.

- Mixed WPA2 / WPA-PSK

3.

5.

- Share + WEP Enable (Less secure)

6.

7.

Passphrase: key for wireless authentication

8.

- WPA-PSK, WAPA2-PSK: Assign a key

9. codes

10. default WEP Key 1 then assign 26 Hex

11.

12.

13. Apply

14.

Please see the relevant sections of User Manual for more detail information.

Troubleshooting

1. None of the LEDs are on when you turn on the router.

Check the connection between the adapter and the router. If the error persists, you may have a hardware problem. In this case you should contact technical support.

2. You have forgotten your router login and/or password.

Try the default login and password, please refer to User Manual. If this fails, you can restore your router to its factory settings by holding the Reset button on the back of your router for 6 seconds or more.

3. Can’t ping any PCs on the LAN.

Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC connected. If it is off, check the cables between your router and the PC. Make sure you have uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet mask are consistent between the router and the workstations.

Product Support and Contact Information

Most problems can be solved by referring to the Troubleshooting section in the User Manual. If you have other inquiries or need further technical support, please contact with your Internet

Service Provider or visit us at www.bectechnologies.net

.

9