Showtec LP 416 lighting controller Manual
Below you will find brief information for lighting controller LP 416. The LP 416 is a compact light controller equipped with very useful features: 4 channel chaser with 16A max. load, background function, 9 built-in programs, 5 modes: Hold dim, Hold sound, Program sound, Program speed, Sound Mode via Audio Input (19), Master and channel dim faders, sound activated, power supply: AC 220V-240V, 50/60 Hz, power consumption: max. 16 A total max.8 A per channel, power connector: Cable without connector, output power: 5A each channel, 16A max., output connector: 4 pcs schuko, analog output: 0-10 Volt, 8 pole din connector, audio output: XLR, Cinch, fuse: F8A 250V 6x32mm, dimensions: 483 x 130 x 135 mm (LxWxH), weight: 5,5 kg.
advertisement
MANUAL
ENGLISH
LP-416 V2
Ordercode: 50750
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
LP-416
Table of contents
Ordercode: 50750
1
LP-416
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Showtec LP-416
Power cable (1,5 m)
User manual
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual
Before your initial start-up, please make sure that there is no damage caused by transportation. Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
Ordercode: 50750
2
LP-416
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not open the device and do not modify the device.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoor, avoid contact with water or other liquids.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
Only operate the device after having familiarized with its functions.
Avoid flames and do not put close to flammable liquids or gases.
Always keep case closed while operating.
Always disconnect power from the mains, when device is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power cord from time to time.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. Device must be installed out of the reach of children. Never leave the unit running unattended.
The user is responsible for correct positioning and operating of the LP-416. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
Repairs, servicing and electric connection must be carried out by a qualified technician.
For replacement use fuses of same type and rating only.
WARRANTY: Till one year after date of purchase.
Operating Determinations
This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
The minimum distance between light-output and the illuminated surface must be more than 1 meter.
The maximum ambient temperature ta = 35°C must never be exceeded.
The relative humidity must not exceed 50 % with an ambient temperature of 35° C.
If this device is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, crash etc.
You endanger your own safety and the safety of others!
Ordercode: 50750
3
LP-416
Connection with the mains
Connect the device to the mains with the power-plug.
Always pay attention, that the right color cable is connected to the right place.
International
L
EU Cable
BROWN
UK Cable
RED
US Cable
YELLOW/COPPER
N
BLUE
YELLOW/GREEN
BLACK
GREEN
SILVER
GREEN
Pin
PHASE
NEUTRAL
PROTECTIVE GROUND
Make sure that the device is always connected properly to the earth!
Improper installation can cause serious damage to people and property!
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [email protected] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper inside the box:
01) Your name.
02) Your address.
03) Your phone number.
04) A brief description of the symptoms.
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is damaged due to shipping. Transportation damage has to be reported to us within one day after receipt of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement, regardless of the agreement of which the obligation is resulting.
Ordercode: 50750
4
LP-416
Description of the device
Features
The LP-416 is a compact light controller equipped with very useful features:
• 4 channel chaser with 16A max. load
• Background function
• 9 built-in programs
• 5 modes: Hold dim, Hold sound, Program sound, Program speed, Sound Mode via Audio Input (19)
• Master and channel dim faders
• Sound activated
• Power supply: AC 220V-240V, 50/60 Hz
• Power consumption: max. 16 A total max.8 A per channel
• Power connector: Cable without connector
• Output power: 5A each channel, 16A max.
• Output connector: 4 pcs schuko
• Analog output: 0-10 Volt, 8 pole din connector
• Audio output: XLR, Cinch
• Fuse: F8A 250V 6x32mm
• Dimensions: 483 x 130 x 135 mm (LxWxH)
• Weight: 5,5 kg
NOTE:
Knowledge of DMX is required to fully utilize this unit.
Front
Ordercode: 50750
5
Fig. 01
LP-416
Front
Fig. 02
01) Power LED
Indicates if the unit is ON.
02) Channel LED
These LEDs allow you to monitor the output of each channel.
03) Mode select indicators
Indicates which of the 4 modes is currently active.
04) Master dimmer
Controls the overall dim level of the 4 channels.
05) Background level
With this fader you can set the background level (minimum output level) of the 4 dimmer channels.
This can "soften" the chaser effects so they become less aggressive. Attention: don't set this fader to maximum, you won't be able to see the chaser patterns or set proper dimming levels for the 4 channels.
06) Program speed control
When "program speed" mode is selected, you can change the speed of the selected chaser program.
07) Power switch
Used to switch the unit ON/OFF.
08) Audio sensitivity
Used to adjust the input sensitivity of the external audio inputs. Adjust the level until the sound activated functions work nicely to the rhythm of the music.
09) Dimmer channels
These are 4 faders used to set the individual dimming levels of the 4 channels. Below each fader there’s a flash button to set the output of the corresponding channel to 100% (full) for as long as the button is pressed.
10) Program display
Shows which of the 4 modes is currently active.
11) Mode select
Used to select 1 of the 4 user modes:
Hold Dim: This mode can be used to control the dimming levels of the outputs. The 4 faders can be used to set the dimming level of each channel output individually.
Hold Sound: The Music is divided into 4 different frequency ranges (bass, middle, high, antibass).
Each of the 4 output channels will respond to a different frequency range.
Program Sound: The chaser program selected with the "program select" button will be displayed. The chaser speed is synchronised to the rhythm of the music.
Program Speed: The chaser program selected with the "program select" button will be displayed. The chaser speed can be adapted with the speed fader.
Ordercode: 50750
6
LP-416
12) Program select
When you have selected 1 of the 2 program modes then you can use the program select button to choose the program you like. Nine different chaser programs can be selected. Program 0 is a random program.
13) Full switch
Use this button to set the output of the 4 channels to 100% (full) for as long as the button is pressed.
14) Standby switch
Used to cutoff (blackout) the output of the 4 dimmer channels. The 4 switch channels are not affected.
15) Speed X10
Used to multiply/divide the speed set by the speed fader by 10.
Backside
Fig. 03
16) Analog output
Use this output to connect an additional analog dimmer pack (ie. Showtec Dim-master 6, D-pack 6)
17) Channel fuses
Each channel has its own fuse. Always replace a blown fuse with a fuse that has the same ratings
(F8A 250V 6x32mm).
18) DMX output
Use to connect the LP-416 to DMX power packs. All 4 channels are available on this output. The dimmer channels are assigned to DMX addresses 001 to 005. Please set the starting address of the connected dimmer pack to 001.
19) Audio Input
This jack accepts a line level audio input signal ranged from 100 mV to 1Vpp.
20) Channel outputs
Each channel has its own Schuko output socket.
21) Power cable
Ordercode: 50750
7
LP-416
Installation
Remove all packing materials from the LP-416. Check if all foam and plastic padding is removed. Screw the equipment into a 19" rack. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply. The device can be sound-controlled as it is equipped with a built-in microphone.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the
EIA-485 standard no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
DAP Audio DMX Data Cables
• DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin.
Ordercode FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
• DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
• DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
Ordercode: 50750
8
LP-416
Maintenance
The operator has to make sure that safety-related and machine-technical installations are to be inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The Showtec LP-416 requires almost no maintenance. However, you should keep the unit clean.
Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in liquid. Do not use alcohol or solvents.
Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections with a damp cloth. Make sure that the connections are thoroughly dry before linking equipment or supplying electric power.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out. If the fuse burns out, the product will not function whatsoever. If this happens, follow the directions below to do so.
01) Unplug the unit from electric power source .
02) Insert a screwdriver into the slot in the fuse cover. Turn the fuse holder counterclockwise. The fuse will come out .
03) Remove the used fuse. If brown or unclear, it is burned out .
04) Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse holder. Be sure to use a fuse of the same type and specification. See the product specification label for details.
Ordercode: 50750
9
LP-416
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit operates properly, do not carry out following steps.
No function
If the LP-416 does not operate properly, refer servicing to a technician.
Suspect four potential problem areas: the power supply, the LEDs, the fuse or the settings (return to default)
01) Power supply. Check if the unit is plugged into an appropriate power supply.
02) The LEDs. Return the LP-416 to your Showtec dealer.
03) A light effect does not respond to the LP-416: Check the DMX-address of the fixture and the controller. Make sure that they match. Make sure that the connections are correct.
04) Check if the device is switched on.
05) If all of the above appears to be O.K., plug the unit in again.
06) If nothing happens after 30 seconds, unplug the device.
07) If you are unable to determine the cause of the problem, do not open the LP-416, as this may damage the unit and the warranty will become void.
08) Return the device to your Showtec dealer.
No Response to DMX
Response: Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with other DMX fixtures? If not, take the controller in for repair. If so, take the DMX cable and the light effect to a qualified technician.
Ordercode: 50750
10
LP-416
Product Specifications
Model:
Power Supply:
Power Consumption:
Fuse:
Dimensions:
Weight:
LP-416
AC 220V-240V, 50/60Hz
16A max.
F8A 250V 6x32mm
482 x 125 x 132 mm (LxWxH)
5,5 kg
Operation and Programming
Signal pin OUT:
Signal output:
Power Connector:
Output Power:
Output Connector: pin 1 earth, pin 2 (-), pin 3 (+)
3-pin DMX signal connector OUT
Cable without connector
Each channel 5A
4x Schuko
Analog Output:
DMX-Output
Audio Input:
Internal Fuse:
Output Fuses:
Max. ambient temperature t a
:
Minimum distance:
0-10V, 8-pole DIN
3-pin female XLR
Cinch
F1A 250V 5x20 mm
F8A 250V 6x32mm
35°C
Minimum distance to lighted object: 0,5 m
Design and product specifications are subject to change without prior notice.
Website: www.Showtec.info
Email: [email protected]
Ordercode: 50750
11
LP-416
Dimensions
Ordercode: 50750
12
LP-416
Notes
Ordercode: 50750
13
LP-416
Ordercode: 50750
14
©2015 Showtec
advertisement
Key Features
- 4 channel chaser with 16A max. load
- Background function
- 9 built-in programs
- 5 modes (hold dim, hold sound, program sound, program speed, sound mode via audio input)
- Master and channel dim faders
- Sound activated
- Analog output
- Audio output