PARADOX NV35MX Installation manual

NV35MX

Installation Manual V1.0

Outdoor/Indoor Window and

Sliding Door Dual Detector with

Anti-Masking and Pet Immunity

4. Attach the Main Unit to the back cover - ensure the locks snap closed.

NV35MX-EI01

General Description

Thank you for choosing the NV35MX for your professional protection needs. The NV35MX EVO version will provide you the most advanced window and sliding door protection either in Pet Immune or Sharp mode, while programming can be done remotely via EVO bus connection. If you have any comments please write to us at Paradox.com/products/ feedback.This guide describes how to install and program the NV35MX.

Pet Recommended Installation (please read)

The NV35MX has been designed to be installed within the frame of windows and doors when installed outdoors. This will ensure the best performance against false alarms when random pets such as birds, cats and small dogs access the window sill. Other installation methods can be used with the NV35MX such as wall beam protection but if installed outside of the frame its pet immunity may be compromised.

Installing the NV35MX

1. Remove the NV35MX front cover - open the Captive screw.

Front cover

Captive screw

Figure 1 – Removing the Front Cover Figure 2 – Main Unit

2. Remove the Main Unit: open the two snap-lock mechanisms on each side of the back cover attaching the Main Unit to the back cover as displayed below. Then remove the Main Unit.

Figure 3 – Removing the Main Unit

3. Pull the wires from the control panel through the knockout holes and mount the back cover onto the window frame or wall using screws.

Knockout holes

Mounting screw 1

Tamper knockout hole

Mounting

Tamper screw 2

Figure 4 – Mounting the Back Cover

1 2 3

Figure 5 – Attaching the Main Unit

5. Connect the wires to the terminal blocks according to the following wiring assignment.

Terminal Connector

1

2

3

4

Table 1: Wiring Assignment

Recommended Wiring Assignment

Bus Label Wire Color

12V+

Minus (-)

Data

Clock

Red

Black

Green

Yellow

6. Replace the front cover and close the Captive screw.

Warning: Do not obscure the detector's field of view.

Programming the NV35MX

Program the detector with a keypad or BabyWare software.

Programming with a Keypad

1. Enter EVO Installer Programming Mode.

2. Enter Module Programming: a Enter section [4003] in the Enter Section field.

b Enter the detector’s 8-digit [SERIAL NUMBER].

c Enter the 3-digit [SECTION] number you want to program.

3. Program required functions in section [001] (table 2), section [002]

(table 3) and section [003] (table 4) below.

Bit

[1]

[3]

[4]

[5]

Table 2: Section [001]

Function

LED Display Alarm

Status/Description

O N : Enabled (default) O FF : Disabled

LED Display Trouble O N : Enabled (default) O FF : Disabled

LED Display Anti- Mask O N : Enabled (default) O FF : Disabled

Anti- Mask O N : Enabled (default) O FF : Disabled

Bit

[1]

[2]

[3]

Table 3: Section [002]

Function Status/Description

Unit Tamper

Wall Tamper

PET Immunity

O

O

O

N

N

N

: Enabled (default), O

: Enabled (default), O

FF

FF

: Disabled

: Disabled

: Enabled (default) (PET Mode)

O FF : Disabled (SHARP Mode)

Table 4: Section [003]

PIR Sensitivity Level

Low: 00 Normal: 01 (default) High: 02

PARADOX.COM

Programming with BabyWare

1. Open BabyWare.

2. Select the detector and set zone type.

3. Right-click on the detector to open detector Programming.

Beam Pattern

PET Mode

4. Configure the required settings.

Testing the NV35MX

Perform a Walk-Test to test successful installation: Walk slowly across the far end of the detection range. Ensure detection.

Walk test mode lasts 5 minutes after the tamper screw is closed.

LED Display

Feature

Tamper open

LED Status Indicator

Green: ON for 0.3 seconds every 30 seconds

PIR sensitivity level setting

Green: Flashes 1-3 times according to the selected level

Alarm detection Red: ON for 2 seconds

Booting/Tamper close Green/Red alternating flashes for 30 seconds

Anti-mask detection Orange: Flashes ON/OFF 3 times every 60 seconds

Technical Specifications

Model Number NV35MX

Infrared Sensor type 2 Dual elements

Detection range PET Immunity mode: 7.5m x 2m (25 x 7 ft).

Sharp mode: 10 x 2m (33 x 7 ft)

Super Pet Immunity

Anti- mask

Input voltage

Current consumption Typical: 15mA

Maximum: 19.2mA

Compatibility EVO systems

Outdoor protection IP54

-35°C to +50°C Operation temperature

Relative humidity

Dimensions

Certifications

Weight

Pet size approximately 50cm

Active IR detection for blocking 30cm and sprayed liquid

10 to 15 VDC

95% non-condensing

12.3 x 6.1 x 4.3 cm (4.8 x 2.4 x 1.7 in.)

CE, EN50131-2-2 Grade 3, Class IV

100g / 0.2 lb

SHARP Mode

Top View

PET Immunity Mode Installation

Notifications

Changes or modifications to this equipment not expressly approved by the party responsible for compliance (Paradox Security Systems Ltd.) could void the user’s authority to operate the equipment.

Warranty

The Limited Warranty Statement found on the website www.paradox.com/terms.

Patents

Your use of the Paradox product signifies your acceptance of these terms and conditions. The following US patents may apply 5,886,632 and 6,215,399. Other Canadian and international patents may apply.

Printed in Canada 08/2015

PARADOX.COM