SunStone SSMat 1.0, SSMat 1.5, SSMat 2.0, SSMat 3.0, SSMat 4.0, SSMat 5.0, SSMat 6.0, SSMat 7.0, SSMat 8.0, SSMat 9.0, SSMat 10.0 Electric Underfloor Heating Mats Installation & Operating Instructions
Below you will find brief information for SSMat 1.0, SSMat 1.5, SSMat 2.0, SSMat 3.0, SSMat 4.0, SSMat 5.0, SSMat 6.0, SSMat 7.0, SSMat 8.0, SSMat 9.0. The SSMat series of electric underfloor heating mats is designed to provide a comfortable and efficient way to heat your home. The mats are easy to install and can be used under a variety of flooring types, including tile, wood, and laminate. The mats are also energy efficient, meaning they will help you save money on your heating bills.
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
Installation & Operating Instructions
Electric Underfloor Heating Mats
For use with SS-PSTAT and SS-TOUCHSTAT
Thermostat Models
Model
SSMat 1.0
Dimensions
0.5 x 2.0m
Area Covered
1.0sqm
SSMat 1.5
SSMat 2.0
SSMat 3.0
SSMat 4.0
SSMat 5.0
SSMat 6.0
SSMat 7.0
SSMat 8.0
SSMat 9.0
SSMat 10.0
0.5 x 3.0m
0.5 x 4.0m
0.5 x 6.0m
0.5 x 8.0m
0.5 x 10.0m
0.5 x 12.0m
0.5 x 14.0m
0.5 x 16.0m
0.5 x 18.0m
0.5 x 20.0m
1.5sqm
2.0sqm
3.0sqm
4.0sqm
5.0sqm
6.0sqm
7.0sqm
8.0sqm
9.0sqm
10.0sqm
Affordable Underfloor Heating
SunStone Underfloor Heating
Tel: 0845 034 8272
Wattage @
230Vac
150 W
225 W
300 W
450 W
600 W
750 W
900 W
1050 W
1200 W
1350 W
1500 W
Amperage @
230Vac
0.65 A
0.98 A
1.30 A
1.96 A
2.61 A
3.26 A
3.91 A
4.57 A
5.22 A
5.87 A
6.52 A
IMPORTANT NOTES
(To avoid damaging your new heating system)
DO NOT CUT THE HEATING WIRE
DO NOT shorten the heating wire
DO NOT overlap the heater with another heater or wire in case of overheating.
DO NOT run the sensor wire or power lead over or under the heating wire.
DO NOT connect mats in series, only in parallel.
DO NOT put built-in units or solid-based furniture on the heated floor areas.
ALWAYS test the system before, during and after installation.
ALWAYS ensure everyone involved in the installation or construction knows how to keep the system safe from damage.
ALWAYS keep an even spacing between heating elements.
ENSURE CORRECT MEASUREMENTS
Cut mats cannot be returned, so check that you have the correct room dimensions and heater size and quantities before starting on the installation.
ENSURE YOU HAVE THE NECESSARY TOOLS
• Thermostat with floor sensor
• RCD: required as part of all installations
• Multi-meter: for testing the resistance of mats
• Electrical trunking/conduit for housing the unheated
power leads
• Electrical housing, back boxes & junction boxes; back
box for the thermostat must be at least 35mm deep
• Permanent marker & measuring tape
• Pair of small utility scissors for cutting the fibreglass
mesh
• Tape (to secure floor sensor and loose wire)
1
2
GENERAL DO’S & DON’TS
Choice of floor covering
The SunStone system has been designed primarily for use with stone or tile floors. If you are considering using any other type of floor covering, such as carpet or wood laminate, please contact our customer services helpline for more information before starting your installation.
Electrical Installation: a job for the professionals
As with all electrical projects governed by Part P regulations, all mains electrical connections must be undertaken by a certified electrician. All work must conform to BS 7671:2008, the current IEE Wiring Regulations.
Installing an RCD
The SunStone undertile heating system must be wired via an RCD. You must install a dedicated RCD if one is not already present . You may wish to use a fused spur/RCD. No more than 4.8kW of heating may be connected to a single 30 milliamp RCD.
NOTE: It is possible to run the heater(s) from an existing circuit. Consult with an electrician to determine whether or not the circuit can handle the load and if it is RCD protected.
Testing of the Heater
One of the most important steps to be taken when installing the heating system is the testing process.
The system should be tested before, during and after its installation:
Before: Using a multi-meter, check the resistance of each mat prior to installation to ensure that it has not been damaged whilst in transit to the installation site. Make a note of the mat resistances in the table located on page 4 of this manual.
During: Test the resistance of each mat again once they have been secured to the subfloor to maintain that no damage occurred during installation.
After: Test again after the floor covering has been laid to ensure that no damage has been done during the setting of the tiles.
Do’s and Don’ts:
Do - plan the the heater layout and installation so that any drilling after tiling (e.g. for fixing sanitary ware) will not damage the wiring.
Do - use ceramic tile adhesives and grouts suitable for use with undertile heating (they must contain a flexible additive)
Do - wait at least 10 days before switching the system on for the first time in order for the tile adhesive to dry.
Do - ensure that the heating element including joints are completely embedded within adhesive.
Don’t - ever cut or shorten the heating wire at any time
Don’t - allow traffic over an installed mat. This is when damage is most likely to occur.
Don’t - store tiles or other sharp or heavy objects on the mats while tiling.
Don’t - attempt to install the heating up walls or up a set of stairs.
Don’t - install heating mats under permanent fixtures.
IMPORTANT!
If at any point during the installation you are unsure of your next step, please call the helpline on 0845 034 8272.
TECHNICAL INFORMATION
The SunStone Heating Mat
A - Heating Element
B - Fibreglass mesh
C - Double-sided tape
D - Factory-made joint
E - Power lead (3-core)
F - Termination joint
G - Floor sensor
E
D
A
B
G
C
F
SYSTEM COMPONENTS
The Heating Element
The heating element is constructed of PVC insulation and a metallic earth braid surrounding two heating wires. The element is attached to the fibreglass mesh (B) using a double-sided tape (C) and is spaced so as to give an even heat throughout the covered area. The heating element is terminated at one end with a 3m power lead (E) which supplies power to the element via the thermostat. The factory made joint (D) which connects the two must be installed under the tiles. It may be necessary to cut a small groove in the subfloor to allow for the extra thickness of the power lead.
Separating the Heating Element from the Fibreglass Mesh
In almost all installations, it will be necessary to separate the heating element from the mesh in order to fit the mat into an irregularly shaped area.
This is most easily done using a small pair of scissors, not a utility knife. When cutting the mesh, it is crucial that the element is not nicked, cut or damaged in any way. If you believe you have cut the wire, call the helpline immediately.
Floor sensor
Proper installation of the floor sensor (G) is critical if the thermostat and floor warming system is to work properly.
The sensor, which is embedded in the adhesive, should be installed centrally between two runs of heating element and should extend a minimum of 150mm into the heated area. It is best to avoid placing the tip of the sensor in areas prone to heat fluctuations due to drafts, sunlight, radiators or hot water pipes. You may wish to cut a groove in the floor to accept the sensor cable and tip in order to keep them at the same height as the heating element.
3
4
TESTING YOUR HEATING SYSTEM
We recommend that you test your heating system at least three times during the installation process to ensure that you do not install a damaged heating mat:
- before installation
- during the mat fixing process
- immediately prior to tiling
Testing with a multi-meter:
The resistance (ohms) of each mat should be measured from the live (brown) wire to the neutral (blue) wire. We recommend the use of a digital multi-meter set to a range of 0-20k ohms for testing.
Please note that due to the high resistance of the wire, it may not be possible to get a continuity reading from a mat and as such, continuity testers are not recommended.
Take a moment to note the readings you get from the multi-meter in the table below.
The readings should be within +/- 5% of these measurements:
1 sqm mat = 353 ohms
1.5 sqm mat = 237 ohms
2 sqm mat = 177 ohms
3 sqm mat = 118 ohms
4 sqm mat = 88 ohms
5 sqm mat = 70 ohms
6 sqm mat = 59 ohms
7 sqm mat = 50 ohms
8 sqm mat = 44 ohms
9 sqm mat = 39 ohms
10 sqm mat = 35 ohms
If at any time you do not get the proper readings or suspect that there is a problem, call the helpline immediately on 0845 034 8272.
Roll no. Mat Size “Proper” reading Test 1 reading Test 2 reading Test 3 reading
ELECTRICAL CONSIDERATIONS
Install the RCD
You must install a dedicated RCD if one is not already present. You may wish to use a fused spur/RCD. No more than 4.8kW of heating may be connected to a single 30 milliamp RCD.
NOTE: It is possible to run the heater(s) from an existing circuit. Consult with an electrician to determine whether or not the circuit can handle the load and if it is RCD protected.
Install electrical boxes and trunking
You will require a deep (35-40mm) back box for the thermostat. If you are installing more than two heaters, a junction box will also be required. The wiring from the heater to the thermostat should be chased into the wall and protected by conduit or plastic trunking.
Connecting the thermostat
The thermostat should be connected to the main electrical supply via a fuse or circuit breaker in accordance with wiring regulations. The thermostat should be installed within the room or area to be heated. In the case of bathroom installations, electrical regulations prohibit the installation of the thermostat within the bathroom itself. In such cases, the thermostat should be fitted to the outside of an internal wall of the bathroom, as close as possible to the heating power supply wires.
Wiring of the
Thermostat
Lout Lin Nin Nout
1 2
Power via RCD live neutral connector block floor probe
5
6
GETTING THE SUBFLOOR READY
Wooden Subfloors
Make sure that there is enough underfloor ventilation.
Secure existing floorboards and if need be, make them even first with a latex/cement self-levelling compound to give a flush fit for the subsequently applied WBP plywood.
Refer to BS 5385: Part 3, clause 14.4 regarding sealing the backs and edges of the plywood.
Fixing ply directly to joists will not always provide a sufficiently stable floor finish for accepting tiles; fitting tongue & groove flooring and then over-boarding with ply or tile backer board is recommended. A rigid base is essential.
The above recommendations apply to small areas as advised in clause 14.4 of BS 5385: Part 3.
Concrete Subfloors
For best results and ease of installation, the use of an extruded polystyrene “building” or “tile backer board” with cement-based facing is recommended. Fixing of the board should be as per the manufacturer’s instructions.
After attaching the board to the subfloor, the undertile heating system may be laid directly on top of the board, and then tiled over. It is important to ensure that the tile adhesive and grout used are flexible and that the tile backer/building board has been fitted as per the manufacturer’s instructions. High quality, cement-based adhesives with their flexible additives are most suitable.
INSTALLING THE MAT
1. Make Indications on the Subfloor
Use a permanent marker to mark out the areas on the subfloor where units and fixtures will be located. Do not install the heating mat in any of these areas.
Next, mark the positions and planned route of the power lead cables as well as the position of the floor sensor. Indicate on the subfloor the locations where the mats will need to be flipped or turned or where loose wire (detached from mesh) will need to be laid.
Please refer to pg 8 to see how mats can be modified to for various areas.
2 Make References on the Mat
Mark the location of any cuts, flips or turns on the mat itself. Double-check once more that you have the proper number and size of mats for your area.
3. Test the heating Mats
Perform test #1 for each mat as explained in the manual.
4. Trial fit the mat(s)
Laying the mats out according to your plan. At this stage, it is still possible to make any last minute adjustments in the mat layout before securing them. Take care not to step on or kink the mat as this could fracture the wire and damage it.
5. Fit the Mats
Beginning with the mat furthest from the thermostat location, secure the mats to the subfloor using the double-sided tape on the mat.
Any loose wires (wire cut away from mesh) should be no closer than 50mm from each other or from any other wires still attached to the mesh.
Once the mats are in place, check that there are no loose sections, paying close attention to the ends of the mats and any section which has been modified by flipping or turning.
INSTALLING THE MAT (Contd)
6. Install Floor Sensor
The floor sensor that comes with the thermostat should now be placed below the fibreglass mesh, centred between 2 heating elements. It should be secured in place using the double-sided tape. It is also wise at this point to check the resistance of the floor sensor using your multi-meter. You should get a reading of approximately 10,000 - 12,000 ohms, depending on the room temperature. You may need to change the setting on your meter in order to accommodate the higher readings. If you do not get a reading, your sensor may be damaged. If so, call the helpline to obtain a replacement.
NOTE: Do not cover the tip of the sensor with tape. Air pockets may result in incorrect temperature reading.
7. Fit the Power Leads
Each mat is fitted with a single power lead for connecting the heating mat to the thermostat. In order to keep the power leads at the same height as the heating element, you may wish to cut or chisel a channel in the subfloor. Take care not to damage the heating element. Secure the leads in place using tape.
The power leads will go into the conduit or trunking that leads from the floor to the thermostat. The power leads may be shortened or extended as needed. However, you must not cut the factory made joint and you must make certain that the joint will be covered with both adhesive and tiles.
8. Test the Heating Mats
Perform test #2 for each mat as explained on page 4
LAYING TILES OVER THE HEATING MATS
When all your mats are installed and the power leads and floor sensor have been secured, it is time to begin laying your tiles.
NOTE: Ensure that all of the heating element including the joints are cover in adhesive and tiled over. Do not tape over the joints as this will create air pockets that can cause the heater to fail. There are two methods available to you, a single-step or dual-step method.
Single-step method:
Apply a thick layer (5-10mm) of tile adhesive directly onto the heating mats.
Lay the tiles directly onto the adhesive layer.
Dual-step method
1. Completely cover the heating mats with a smooth layer of flexible adhesive or latex self-levelling compound and allow to dry. Allow this level to dry; it will normally take 1 day per mm.
2. Apply a thin layer (3mm) of flexible adhesive and tile as normal.
Tips for choosing a method:
- It is easier to lay mosaic tiles using the dual-step method
- If this is your first installation, you may find it easier using the dual-step method
- If the floor will not be tiled straight away, it is better to use the dual-step method for protecting the wire
- The single-step method is more typically used by experienced installers of this heating system
Test the heating mats
Perform test #3 for each mat as explained in the manual.
Waiting Period
You must allow the tile adhesive and any self-levelling used to set before powering-up the system.
This can take 10 to 14 days depending on the amount of material used. Failure to wait the proper amount of time will result in damage to the system as well as cause the adhesive and grout to dry too quickly, thereby becoming brittle, leading to tiles lifting and/or cracking.
7
8
HOW TO MAKE TURNS & FLIPS WITH MATTING SYSTEM
The heating mats can be modified by cutting the fibreglass mesh (NOT THE WIRE) and either flipping or turning the mat as needed. Examples of turns and flips can be found below. It may not be neccessary to completely remove the heating wire from the mesh in order to fit the system into small or odd-shaped areas. It is essential that care is taken during this process not to nick the wires with your scissors.
WARRANTY
This SunStone underfloor heater is guaranteed against any fault caused by manufacturing defect for a period of 10 years from date of purchase. There is no other warranty, express or implied. No claim can be brought against the manufacturer or its agents for any consequential damages whatsoever.
This warranty covers the cost of the replacement or repair, at the discretion of the manufacturer, of the heater only.
Send the completed form back to: SunStone Warranty, BCR House, 3 Bredbury Business Park, Stockport,
SK62SN
Proof of purchase is needed in the event of a claim, so keep your invoice with this warranty
This warranty is subject to the following conditions:
YE
AR
WA
RRANTY
1. To qualify for your 10-year warranty, please register your product by completing
and returning the attached “Warranty Registration” form.
2. In the event of a claim, proof of purchase will be required, so keep your warranty
with the installation manual.
3. The heater has been installed and used in full compliance with the installation manual.
4. The heater has been earthed and protected by the RCD at all times.
5. The heater is used in conjunction with a thermostat or control system approved by SunStone.
6. The warranty is returned to SunStone within 1 month of purchase of the heater(s).
10
7. If SunStone or its agents carry out diagnostic or remedial work as a result of a claim being made, and
evidence of incorrect installation or usage of the heater becomes apparent, SunStone or its agents shall
have the right to levy reasonable charges for the work undertaken by them.
If the heater fails due to damage caused during installation or tiling, this warranty does not apply.
You must therefore ensure that the heater is working as laid out in the installation manual prior to tiling.
Owner’s Name
Address
Installer Electrician
Date of purchase
Please indicate the room the heating system is installed:
Kitchen / Bathroom / Conservatory / Hall / Other:
Subfloor:
Insulated Tile Backer Board / Wood / Concrete/Screed / Other:
Signed: Date:
9
10
MAT LAYOUT GRID
NOTES
11
PROJECT SUMMARY
This card must be placed in a visible spot close to the consumer unit.
Please Note:
1. A 30mA RCD must be used in conjunction with the heating system.
2. Never cut or shorten the heating element
3. During installation, make sure that the whole heating element (including joints)
are installed beneath the tiles.
4. For the guarantee to be valid, this form must be completed.
5. Check that the values match the ones in the instruction manual.
6. Draw a plan showing the layout of the heater
CAUTION!
Radiant Floor Heating Systems
Warning– Risk of electric shock
Electric wiring and heating panels contained below the floor.
Do not penetrate with nails, screws, or similar devices.
Do not restrict the thermal emission of the heated floor.
Location of heater
Resistance Value
Pre-Installation: __________________ohms
Post-Installation: _________________ohms
Heater description
Wattage: __________________
Model: ____________________
Signature
Date
12
Electrician’s Part P registration no.
Company stamp/name
Affordable Un derfloor Heating
SunStone Underfloor Heating
Tel: 0844 847 2959
advertisement
Key Features
- Easy to install
- Energy efficient
- Can be used with a variety of flooring types
- Provides comfortable and efficient heating
- 10 year warranty
- Comes with floor sensor