Land Pride SBL25 66, 74, 84 Snow Blower Operator’s Manual

Table of Contents
Snow Blowers
SBL2566, SBL2574, & SBL2584 with S/N 891531+
35598
370-478M
Operator’s Manual
!
Read the Operator’s Manual entirely. When you
see this symbol, the subsequent instructions and
warnings are serious - follow without exception.
Your life and the lives of others depend on it!
Cover photo may show optional equipment
not supplied with standard unit.
© Copyright 2015
Printed
3/18/15
Table of Contents
Table of Contents
Important Safety Information . . . . . . . . . . . . . 1
Section 4: Adjustments . . . . . . . . . . . . . . . . . 20
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
...............6
...............6
...............6
...............6
Discharge Chute & Spout Deflector . . . . . . . . . . . . 20
Spout Deflector Adjustment . . . . . . . . . . . . . . . . 20
Chute Rotation Gear Alignment . . . . . . . . . . . . . 20
Chute Rotation Adjustment . . . . . . . . . . . . . . . . . 20
Outer Skid Shoe Adjustment . . . . . . . . . . . . . . . . . 21
Inner Skid Shoe Adjustment . . . . . . . . . . . . . . . . . 21
Auger Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Level Run Indicator Adjustment . . . . . . . . . . . . . . . 22
Section 1: Assembly & Set-up . . . . . . . . . . . . 7
Section 5: Operating Instructions . . . . . . . . . 23
Skid Steer/Tractor Requirements . . . . . . . . . . . . . . 7
Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . 7
Loading & Unloading . . . . . . . . . . . . . . . . . . . . . . 7
Optional Outer Skid Shoes . . . . . . . . . . . . . . . . . . . 7
Optional Inner Skid Shoes . . . . . . . . . . . . . . . . . . . . 7
SBL2566 Chute Assembly . . . . . . . . . . . . . . . . . . . . 8
SBL2574 & SBL2584 Chute Assembly . . . . . . . . . . 8
Spout Deflector, Hydraulic Cylinder . . . . . . . . . . . . . 9
Quick Coupler Set-up . . . . . . . . . . . . . . . . . . . . . . 10
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Pre-Operational Safety Check . . . . . . . . . . . . . . . . 23
Operational Safety Check . . . . . . . . . . . . . . . . . . . 23
General Safety Information . . . . . . . . . . . . . . . . . . 24
Mounting & Dismounting Skid Steer . . . . . . . . . . . 26
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Leveling The Snow Blower . . . . . . . . . . . . . . . . . . 27
General Operator Instructions . . . . . . . . . . . . . . . . 27
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Application . . . . . . . . . . . . . . . .
Using This Manual . . . . . . . . . . .
Owner Assistance . . . . . . . . . . .
Serial Number . . . . . . . . . . . .
Section 2: Equipment Hook-up & Unhook . . 11
Snow Blower Hook-up . . . . . . . .
Hydraulic Hose Hook-up . . . . . .
Solenoid Hook-up . . . . . . . . . . .
Check Equipment Clearances . .
Unhooking The Snow Blower . .
..............
..............
..............
..............
..............
11
12
12
13
14
Section 3: Options . . . . . . . . . . . . . . . . . . . . . 15
Motor Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Flat Face Couplers . . . . . . . . . . . . . . . . . . . . . . . . 15
Case Drain Coupler & Cable Ties . . . . . . . . . . . . . 15
Electrical Control Harness (Optional) . . . . . . . . . . 16
Control Harness With Deutsch 14 Pin Plug . . . . 16
Control Harness With Deutsch 2 Pin Plug . . . . . 17
Tractor Control Harness With 2 Eyelets . . . . . . . 18
Skid Steer Control Harness With 2 Eyelets . . . . 19
Outer Skid Shoes . . . . . . . . . . . . . . . . . . . . . . . . . 19
Inner Skid Shoes . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Section 6: Maintenance & Lubrication . . . . . 29
General Maintenance Information . . . . . . . . . . . . . 29
Tractor/Skid Steer Maintenance . . . . . . . . . . . . . . 29
Auger & Impeller Inspection . . . . . . . . . . . . . . . . . . 29
Outer Skid Shoe Option . . . . . . . . . . . . . . . . . . . . . 30
Inner Skid Shoe Option . . . . . . . . . . . . . . . . . . . . . 30
Grader Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . 31
Ordering Replacement Parts . . . . . . . . . . . . . . . . . 31
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Auger Flange Bearing . . . . . . . . . . . . . . . . . . . . . 32
Section 7: Specifications & Capacities . . . . . 33
Section 8: Features & Benefits . . . . . . . . . . . 34
Section 9: Troubleshooting . . . . . . . . . . . . . . 35
Section 10: Torque Values Chart . . . . . . . . . 36
Section 11: Warranty . . . . . . . . . . . . . . . . . . . 37
© Copyright 2015 All rights Reserved
Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.
Land Pride is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
▲
Table of Contents
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Safety at All Times
Look For The Safety Alert Symbol
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read all
instructions noted on them.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert, and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control, and accident prevention are
dependent upon the awareness, concern, prudence, and
proper training of personnel involved in the operation,
transport, maintenance, and storage of equipment.
▲ The operator must not use drugs
or alcohol as they can change the
alertness or coordination of that
person while operating equipment.
The operator should, if taking overthe-counter drugs, seek medical
advice on whether he/she can
safely operate the equipment.
▲ Operator should be familiar with all
functions of the unit.
▲ Make sure all guards and shields
are in place and secured before
operating implement.
▲ Start skid steer with steering levers
and hydraulic controls in neutral.
▲ Keep all persons away from
equipment and work area.
▲ Operate implement and loader
arms from the driver’s seat only.
▲ Dismounting from a moving unit
can cause serious injury or death.
▲ Do not allow anyone to stand
between skid steer/tractor and
implement while hooking-up to
implement.
▲ Keep hands, feet, and clothing
away from power-driven parts.
▲ Watch out for objects overhead
and along side such as fences,
buildings, wires, trees, limbs, etc.,
while transporting and operating
attached implement.
▲ Detach and store implement in an
area where children normally do
not play. Secure implement by
using blocks and supports.
3/18/15
!
Be Aware of 
Signal Words
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
! DANGER
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
For Your Protection
▲ Thoroughly read and understand
the “Safety Label” section, read all
instructions noted on them.
! WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
! CAUTION
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
Use Safety 
Lights and Devices
▲ Slow moving tractors, skid steer,
self-propelled equipment, and
towed implements can create a
hazard when driven on public
roads. They are difficult to see,
especially at night.
▲ Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
Parts Manual QR Locator
Dealer QR Locator
The QR (Quick Reference) code on the
front cover and to the left will take you to
the Parts Manual for this equipment.
Download the appropriate App on your
smart phone, open the App, point your
phone on the QR code and take a picture.
The QR code on the left will
link you to available dealers
for Land Pride products.
Refer to Parts Manual QR
Locator on this page for
detailed instructions.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
1
Table of Contents
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Skid Steer Shutdown 
& Storage
Before leaving operator’s
seat:
▲ Lower lift arms and put
attachment flat on the ground.
▲ Turn off engine.
▲ Engage park brake.
▲ If included, raise seat bar and
move controls until both lock.
▲ Remove key to prevent
unauthorized starting.
▲ Use steps, grab-handles and 
skid-resistant surfaces when
getting on and off the loader.
▲ Detach and store implements in
an area where children normally
do not play. Secure implement by
using blocks and supports.
Transport Safely
▲ Comply with state and local laws.
▲ Use towing vehicle and trailer of
adequate size and capacity. Secure
equipment towed on a trailer with
tie downs and chains.
▲ Sudden braking can cause a towed
trailer to swerve and upset. Reduce
speed if towed trailer is not
equipped with brakes.
▲ Avoid contact with any over head
utility lines or electrically charged
conductors.
▲ Always drive with load on end of
loader arms low to the ground.
▲ Always drive straight up and down
ramps with load on “uphill” side of
skid steer or tractor.
▲ Engage park brake when stopped
on an incline.
▲ Maximum transport speed for an
attached implement is 20 mph. DO
NOT EXCEED. Never travel at a
speed which does not allow
adequate control of steering and
stopping. Some rough terrains
require a slower speed.
▲ As a guideline, use the following
maximum speed weight ratios for
an attached implement:
20 mph when weight of attached
implement is less than or equal to
the weight of machine towing the
implement.
10 mph when weight of attached
implement exceeds weight of
machine towing implement but
not more than double the weight.
▲ IMPORTANT: Do not tow a load
that is more than double the weight
of the vehicle towing the load.
OFF
REMO
VE
Tractor Shutdown & Storage
Practice Safe Maintenance
Before leaving operator’s
seat:
▲ Understand procedure before doing
work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
▲ Work in a clean dry area.
▲ Lower attached implement to the
ground and follow all shutdown
procedures before leaving the
operator’s seat to perform
maintenance.
▲ Allow implement to cool completely
before working on it.
▲ If engaged, disengage PTO.
▲ Lower attached implement to
ground or onto support blocks.
▲ Put tractor in park or set park
brake, turn off engine, and remove
switch key to prevent unauthorized
starting.
▲ Wait for all components to come to
a complete stop before leaving the
operator’s seat.
▲ Detach and store implement in an
area where children normally do
not play. Secure implement using
blocks and supports.
▲ Disconnect battery ground cable (-)
before servicing or adjusting
electrical systems or before welding
on implement.
▲ Do not grease or oil implement
while it is in operation.
▲ Inspect all parts. Make sure parts
are in good condition & installed
properly.
▲ Remove buildup of grease, oil, or
debris.
▲ Remove all tools and unused parts
from implement before operation.
OFF
REMO
VE
2
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Prepare for Emergencies
▲ Be prepared if a fire starts.
▲ Keep a first aid kit and fire
extinguisher handy.
▲ Keep emergency numbers for
doctor, ambulance, hospital, and
fire department near phone.
Wear 
Protective Equipment
Avoid High 
Pressure Fluids Hazard
▲ Wear protective clothing and
equipment appropriate for the job.
Clothing should be snug fitting
without fringes and pull strings to
avoid entanglement with moving
parts.
▲ Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
▲ Operating equipment safely
requires the operator’s full
attention. Avoid wearing radio
headphones while operating
machinery.
▲ Escaping fluid under pressure can
penetrate the skin causing serious
injury.
▲ Avoid the hazard by relieving
pressure before disconnecting
hydraulic lines or performing work
on the system.
▲ Make sure all hydraulic fluid
connections are tight and all
hydraulic hoses and lines are in
good condition before applying
pressure to the system.
▲ Use a piece of paper or
cardboard, NOT BODY PARTS, to
check for suspected leaks.
▲ Wear protective gloves and safety
glasses or goggles when working
with hydraulic systems.
▲ DO NOT DELAY. If an accident
occurs, see a doctor familiar with
this type of injury immediately.
Any fluid injected into the skin or
eyes must be treated
within a few hours or
gangrene may
result.
Keep Riders 
Off Machinery
Use Seat Belt and ROPS
911
Tire Safety
▲ Tire changing can be dangerous
and should be preformed by
trained personnel using the
correct tools and equipment.
▲ When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
▲ When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
3/18/15
▲ Never carry riders or use
machinery as a personlift.
▲ Riders obstruct operator’s view.
▲ Riders could be struck by foreign
objects or thrown from the
machine.
▲ Never allow children to operate
equipment.
▲ Operate only tractors & skid steer
loaders equipped with Roll-Over
Protective Structure (ROPS) and
seat belt.
▲ Fasten seat belt snugly and
securely to help protect operator
from being thrown, crushed, or
severely injured if a rollover
occurs; and from falling off the
tractor or skid steer loader and
being ran over. Not using the seat
belt can result in serious injury or
death.
▲ Wearing protective equipment
such as safety shoes, safety
glasses, hard hat, and ear plugs is
highly recommended.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3
Table of Contents
Important Safety Information
Safety Labels
Your Snow Blower comes equipped with all safety labels in
place. They were designed to help you safely operate your
implement. Read and follow their directions.
1. Keep all safety labels clean and legible.
2. Refer to this section for proper label placement. Replace
all damaged or missing labels. Order new labels from your
nearest Land Pride dealer. To find your nearest dealer,
visit our dealer locator at www.landpride.com.
3. Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as
4.
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
Refer to this section for proper label placement.
To install new labels:
a. Clean surface area where label is to be placed.
b. Spray soapy water onto the cleaned area.
c. Peel backing from label and press label firmly onto the
surface.
d. Squeeze out air bubbles with edge of a credit card or
with a similar type of straight edge.
848-840C
Danger: Hands in Chute
2-Places: On both sides
of chute
35599
818-132C
Danger: Thrown Object Hazard
2-Places
35599
818-831C
35599
4
Warning: High Pressure Fluid Hazard
Used only with hydraulic motor and hydraulic cylinders.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Important Safety Information
818-858C
35599
Warning: To Prevent Serious Injury or Death
35598
818-634C
35599
Danger: Rotating Auger 
2-Places
858-148C
35599
3/18/15
Warning: Pinch Point Hazard
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
5
Table of Contents
Introduction
Introduction
Land Pride welcomes you to the growing family of new
product owners.
This Snow Blower has been designed with care and built
by skilled workers using quality materials. Proper
assembly, maintenance, and safe operating practices will
help you get years of satisfactory use from this machine.
Application
Land Pride offers the SBL2566, SBL2574, and SBL2584
Series of residential Snow Blowers ranging from 66" up to
84" in width. They are designed with a skid steer
mounting plate for attaching to skid steers. The SBL2566
can also be attached to a tractor front loader with Land
Pride’s 3-point hydraulic reservoir system (HRS) or
equivalent system mounted on the back. These Snow
Blowers are designed to remove snow from parking lots,
farm yards, feed lots, driveways, walking paths, and
sidewalks in residential and commercial areas.
Land Pride’s unique patent-pending level run indicator
provides the operator with a clear, visible indication that
the Snow Blower is operating level. The auger, impeller,
and chute rotation are powered with individual hydraulic
motors. Adjustable skid shoes mounted on both sides
can be adjusted to carry the Snow Blower above hard
surfaces, loose gravel, and rocks to help increase the life
of the unit.
Owner Assistance
The Online Warranty Registration should be completed
by the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
The parts on your Snow Blower have been specially
designed by Land Pride and should only be replaced with
genuine Land Pride parts. Contact a Land Pride dealer if
customer service or repair parts are required. Your Land
Pride dealer has trained personnel, repair parts, and
equipment needed to service the implement.
Serial Number
Model No. _____________Serial No. ______________
For quick reference and prompt service, record model
number and serial number in the spaces provided above
and again on Warranty page 37. Always provide model
and serial number when ordering parts and in all
correspondences with your Land Pride dealer. Refer to
Figure 1 for location of your serial number plate.
35599
Left Side
See “Specifications & Capacities” on page 33 and
“Features & Benefits” on page 34 for additional
information and performance enhancing options.
Using This Manual
• This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments, 
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
• The information contained within this manual was 
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
• To order a new Operator’s or Parts Manual, contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge, from our website at
www.landpride.com.
Terminology
See Figure 1: “Right” or “Left” as used in this manual is
determined by facing in the direction the machine will
operate while in use unless otherwise stated.
Definitions
Right Side
Serial Number Plate Location
Figure 1
Further Assistance
Your dealer wants you to be satisfied with your new Snow
Blower. If for any reason you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:
1.
Discuss the matter with your dealership service
manager making sure that person is aware of any
problems you may have and has had the opportunity
to assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem, and request assistance.
3. For further assistance write to:
IMPORTANT: A special point of information related
to the following topic. Land Pride’s intention is this
information must be read & noted before continuing.
NOTE: A special point of information that the
operator should be aware of before continuing.
6
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
[email protected]
3/18/15
Table of Contents
Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
Skid Steer/Tractor Requirements
The SBL2566, SBL2574, & SBL2584 Snow Blowers are
designed to attach to skid steers. The SBL2566 can also
be attach to a tractor loader with Land Pride’s 3-point
mounted hydraulic reservoir system (HRS) or equivalent
system mounted on the back. The skid steer and/or
tractor/HRS must meet the following minimum
requirements:
SAE Lift Capacity . . . . . . . . . . . . . . . . . . . . . 1200 lbs
Hitch Type . . . . . . . . . . . . . . . Skid steer/loader plate
Hydraulic Pressure Rating . . . . . . . . . 2500 - 3500 psi
Low Volume Motors & Hoses . . . . . . . . . .12 - 19 gpm
Medium Volume Motor & Hoses . . . . . . . 20 - 26 gpm
High Volume Motor & Hoses . . . . . . . . . 27 - 33 gpm
Hydraulic Hoses . . . . . . . . . . . . . 2 - Hydraulic outlets
Case Drain Hose . . . . . . . . . . . . . 1 - Hydraulic outlet
Skid Steer Weight . . . . . . . . . . . . . See warning below
!
WARNING
Ballast weights may be required to maintain steering control.
Refer to your skid steer or tractor Operator’s Manual to
determine proper ballast requirements.
37225
Outer Skid Shoe Assembly (Right-Hand Shown)
Figure 1-2
Optional Outer Skid Shoes
Refer to Figure 1-2:
1. Attach outer right-hand skid shoe (#1) to the righthand side panel with 1/2"-13 x 1 1/4" GR5 carriage
bolts (#2) and hex flange lock nuts (#3) using the
bottom square holes as shown.
2. Tighten hex flange lock nuts (#3) to the correct
torque.
3. Repeat steps 1 & 2 for the left-hand side.
IMPORTANT: The skid steer or tractor mounted
hydraulic reservoir system must be equipped with a
case drain system.
Torque Requirements
Refer to “Torque Values Chart” on page 36 to
determine correct torque values for common bolts.
Loading & Unloading
Refer to Figure 1-1:
There are two lifting holes (one on each end panel). Use
these holes to attach lift chains during loading/unloading
and while installing skid shoes in assembly & set-up.
37226
Inner Skid Shoe Assembly (Left-Hand Shown)
Figure 1-3
Optional Inner Skid Shoes
Refer to Figure 1-3:
1. Attach skid shoe mount (#2) to the back, left side of
the Snow Blower with 1/2"-13 x 1 1/2" GR5 bolts (#3)
and hex flange lock nuts (#4). Tighten hex flange lock
nuts to the correct torque.
2. Attach inner skid shoe (#1) to skid shoe mount (#2)
with bent pin (#6) as shown. Secure bent pin with
hairpin cotter (#5).
35599
Lift Points
Figure 1-1
3/18/15
3. Repeat steps 1 & 2 for the back, right side of the
Snow Blower.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
7
Table of Contents
Section 1: Assembly & Set-up
SBL2566 Chute Assembly
37432
Refer to Figure 1-5:
1. Remove hex nuts (#8), spring lock washers (#9), hex
head bolts (#7), bearing strap (#2A), and chute
bearings (#4). Keep hardware for reuse.
IMPORTANT: Position chute (#1) facing straight
forward to the front as shown in Figure 1-4 before
sliding base of chute over bearing ring (#10).
2. With discharge chute (#1) facing straight forward.
Slide base of chute over UHMW chute bearing 
ring (#10) until base of chute is fully under chute
rotational stop (#5), bearing strap (#2B), and
engaged with sprocket (#3).
3. Reattach bearing strap (#2A) to snow blower housing
with existing 3/8"-16 x 1 1/2" GR5 bolts (#7), chute
bearings (#4), lock washers (#9), and 
nuts (#8). Tighten nuts (#8) to the correct torque.
4. Verify stop bolts (#6) are at the back as shown.
SBL2566 Chute Assembly
Figure 1-4
SBL2574 & SBL2584 Chute Assembly
35600
Refer to Figure 1-5:
1. Remove hex nuts (#10), spring lock washers (#12),
hex head bolts (#7), and rotational stop (#6). Keep
hardware for reuse.
2. Remove hex nuts (#11), spring lock washers (#13),
hex head bolts (#9), bearing strap (#2A), and chute
bearings (#5). Keep hardware for reuse.
IMPORTANT: Position chute (#1) facing straight
forward to the front as shown in Figure 1-5 before
sliding base of chute over bearing ring (#14).
3. With discharge chute (#1) facing straight forward as
shown. Slide base of chute over UHMW chute
bearing ring (#14) until base of chute is fully under
remaining bearing straps (#2B & #2C) and engaged
with sprocket (#4).
4. Reattach bearing strap (#2A) to snow blower housing
with existing 3/8"-16 x 1 1/2" GR5 bolts (#9), chute
bearings (#5), lock washers (#13), and nuts (#11).
Tighten nuts (#11) to the correct torque.
SBL2574 & SBL2584 Chute Assembly
Figure 1-5
35601
5. Reattach rotational stop (#6) to Snow Blower housing
with existing 1/4"-20 x 3/4" GR5 bolts (#7), rotational
stop (#6), lock washers (#12) and hex nuts (#10).
Tighten nuts (#10) to the correct torque.
Refer to Figure 1-6:
6. Verify stop bolts (#8A & #8B) are left of rotational stop
(#6) as shown.
7.
Tighten hex bolts (#7) to the correct torque.
SBL2574 & SBL2584 Rotational Stop Bar Set-up
Figure 1-6
8
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 1: Assembly & Set-up
37229
35603
Priority Valve Ports
Figure 1-7
Spout Deflector, Hydraulic Cylinder
Refer to Figure 1-7 & Figure 1-8:
1. Route hydraulic hoses (#3 & #4) through hose 
guides (#6 & #7).
2. Tie hoses (#3 & #4) together below hose guide (#7)
with cable tie (#8) in the locations shown.
Refer to Figure 1-9:
3. Screw o-ring end of 9/16" elbows (#2A & #2B) into
cylinder ports on hydraulic cylinder (#1). Do not
tighten elbows at this time.
Hydraulic Hose Hook-up (Spout Deflector to Solenoid)
Figure 1-8
35602
4. Screw 1/4" x 45" short hydraulic hose (#3) to 
elbow (#2B) until tight.
5. Screw 1/4" x 55" long hydraulic hose (#4) to 
elbow (#2A) until tight.
6. Tighten elbows (#2A & #2B) to hydraulic 
cylinder (#1) until tight.
Hydraulic Cylinder Assembly For Spout Deflector
Figure 1-9
3/18/15
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
9
Table of Contents
Section 1: Assembly & Set-up
Quick Coupler Set-up
Refer to Figure 1-10
Two high pressure hydraulic outlets are required for
attaching hydraulic hoses (#7 & #8) and a third outlet is
required for attaching case drain line (#9).
NOTE: How to identify hydraulic lines (#7, #8, & #9):
• Hydraulic pressure line (#7) attaches to port (#1)
located on right-hand side of impeller motor.
• Hydraulic return line (#8) attaches to tee (#3)
located beneath impeller motor.
• Case drain line (#9) attaches to port (#2) located
on top of impeller motor.
1.
Thread hydraulic hoses (#7, #8, & #9) through holes
on the left-hand side of Snow Blower frame. Holes
not shown in illustration.
2. Continue threading hoses through hose loop (#10).
Refer to Figure 1-11
NOTE: Flat face couplers (#11 & #12) and adapters
(#13) are optional. They can be purchased from your
local Land Pride dealer. See “Flat Face Couplers”
on page 15 for detailed information and Land Pride’s
part number.
3. Consult your skid steer Operator’s Manual or
Auxiliary Hydraulic Reservoir Manual to determine
which line on your machine is under pressure when
locked for continuous operation.
IMPELLER MOTOR
35605
Hydraulic Hose Layout (View Without Hitch Plate)
Figure 1-10
4. If installing optional large flat face couplers, skip to
step 5 below. If installing optional small flat face
couplers, screw adapters (#13) to small flat face
couplers (#11 & #12) until tight.
5. Remove plastic cap from hydraulic line (#7).
6. Select couplers (#11 or #12) that will mate with your
machine’s coupling that is under pressure and attach
that coupling to hydraulic line (#7) and tighten.
7.
Remove plastic cap from hydraulic line (#8) and
screw remaining coupler to line (#8) until tight.
NOTE: Coupler (#6) is optional. It can be purchased
from your local Land Pride dealer. See “Case Drain
Coupler & Cable Ties” on page 15 for detailed
information and Land Pride’s part number.
8. If customer chooses to screw case drain line (#9)
directly to the tank/sump, then skip step 9 and go to
“Snow Blower Hook-up” on page 11.
9. If attaching optional coupler (#6) to case drain 
line (#9):
a. Remove plastic cap from case drain line (#9).
b. Wrap teflon tape around the pipe threads on the
end of the case drain line.
35604
c. Screw optional coupler (#6) on tight.
10
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
Quick Disconnect Coupling Set-up
Figure 1-11
3/18/15
Table of Contents
Section 2: Equipment Hook-up & Unhook
Section 2: Equipment Hook-up & Unhook
Snow Blower Hook-up
Refer to Figure 2-1:
1. Check for and remove debris in the hitch point areas
before hooking-up to Snow Blower.
Refer to Figure 2-1:
!
2. Raise lock pins on loader hitch for hook-up.
DANGER
A Crushing Hazard exists when hooking-up equipment. Do
not allow anyone to stand between skid steer/tractor and
implement while hooking-up to implement. Do not operate
hydraulics while someone is near the skid steer/tractor or
implement.
!
CAUTION
Make sure your skid steer/tractor hitch is properly attached to
the Snow Blower hitch. It must be secured under the Snow
Blower top angle bars and loader hitch plate lock handles
must be locked down with locking pins extending fully through
bottom slots in the Snow Blower hitch. An improperly attached
Snow Blower can come loose and fall.
NOTE: The Snow Blowers are designed for skid
steers and tractors with front mounted loaders.
3. Drive skid steer or tractor slowly to the Snow Blower
hitch making sure hitch plate on the skid steer/tractor
is parallel with the Snow Blower’s top angle bars.
4. Rotate top of skid steer/tractor tilt arms slightly
forward.
5. Position top of skid steer/tractor hitch plate under the
top angled bars and slowly raise loader hitch plate up
until hitch plate is seated under the top angle bars.
6. Rotate top of skid steer/tractor tilt arms back until
Snow Blower makes full contact with face of hitch
plate.
7.
Push lock pins on the loader hitch down. Make sure
lock pins go through bottom slots in the Snow Blower
hitch and handles are fully locked down.
IMPORTANT: Set loader arms to float before
blowing snow. The skid shoes can have increased
wear if loader arms are rigid.
8. Set loader arms to float.
4
3
2
1
5
Top Angle Bars
Bottom slots
35599
Hook-up to Snow Blower
Figure 2-1
3/18/15
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
11
Table of Contents
Section 2: Equipment Hook-up & Unhook
Hydraulic Hose Hook-up
!
DANGER
Hydraulic fluid under high pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin or eyes, it must be
treated by a doctor familiar with this type of injury within a few
hours or gangrene may result. DO NOT DELAY.
IMPORTANT: Collect and dispose all oil spills and
leaks in an environmentally safe manner.
IMPORTANT: Hose routing is the responsibility of
the owner/operator of the Snow Blower. Pinched
and/or stretched hoses are not covered under the
warranty.
IMPORTANT: Make sure all coupler fittings are
clean before connecting them to skid steer couplers.
Refer to Figure 2-4 on page 13:
Two high pressure hydraulic outlets are required for the
hydraulic motor and one outlet for the case drain.
1.
Route hydraulic hoses along the most convenient path
to access your skid steer or tractor mounted hydraulic
reservoir couplings.
NOTE: If attaching to a Kubota SVL skid steer, route
hydraulic hoses through Kubota’s SVL Hose Stay
Kit #S6689 as shown in Figure 2-2 below. 
Purchase SVL Hose Stay Kit #S6689 through your
nearest Kubota dealer. Refer to the SVL skid steer
Operator’s Manual for additional instructions.
o
37394
2. Clean quick connect couplers of dirt and then
connect couplers (#1 & #2) to the skid steer couplers
or couplers at the tractor mounted hydraulic
reservoir. Make sure quick connect couplers have
fully engaged. If they have not, check the following:
a. Make sure couplers are same size and type.
b. Make sure hydraulic pressure has been released.
3. If case drain line is fitted with the optional coupler,
then connect that coupler (#3) to the tank/sump
coupler and skip to step 5 below.
4. If screwing case drain line directly to the tank/sump:
a. Remove plastic cap and wrap teflon tape around
pipe threads on end of case drain line (#3).
b. Screw case drain line (#3) to your equipment’s
tank/sump port until tight. All required adapter
fittings are supplied by customer.
5. Turn auxiliary hydraulics on to check impeller
rotation. The impeller should rotate counterclockwise
viewed from the operator’s seat and clockwise
viewed facing impeller and auger from the front. If
impeller rotates incorrectly, switch male and female
couplers on the hydraulic hoses and reconnect
hoses.
6. Cable ties to be added at end of solenoid hook-up.
Solenoid Hook-up
Refer to Figure 2-3 on page 13:
There are six optional wiring harnesses and all connect
the same way to the Snow Blower solenoids (#1 & #2) but
connect differently to the skid steer or tractor. See pages
16 thru 18 for a detailed descriptions of all six.
1.
Skip to step 3 if optional wire harness (#4) has a 6 pin
connector. Otherwise, continue with step 2 below.
2. If solenoid harness has a 14 pin connector, attach
harness to the 14 pin connector located on the end of
the loader arm. Skip to step 4 on this page.
3. There are three toggle switch control harnesses
available. Two are for skid steer mounted Snow
Blowers and one is for tractor mounted Snow
Blowers.
• Install “Control Harness With Deutsch 2 Pin
•
•
SVL Hose Stay Kit #S6689
Plug” using instructions in manual 370-452M
included with this kit. See page 17 for harness
description.
Install “Skid Steer Control Harness With 2
Eyelets” using instructions in manual 370-349M
included with this kit. See page 19 for harness
description.
Install “Tractor Control Harness With 2 Eyelets”
using “Installation Instructions for Tractor
Harness” on page 18.
Kubota SVL Hose Stay
Figure 2-2
12
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 2: Equipment Hook-up & Unhook
4
3
2
1
5
35599
Hydraulic Hoses & Cable Ties
Figure 2-4
35606
Quick Disconnect Coupling Set-up
Figure 2-3
4. Route wire harness (#4) in Figure 2-3 & Figure 2-4
along side hydraulic hoses to solenoids (#1 & #2). 
Do not secure wire harness (#4) with cable ties at this
time.
5. At solenoid (#1), attach brown banded 
connector (#1B) to brown wire connector (#3B) and
white banded connector (#1W) to white wire
connector (#3W).
6. At solenoid (#2), attach red banded connector (#2R)
to red wire connector (#3R) and green banded
connector (#2G) to green wire connector (#3G).
7.
Sit in the skid steer or tractor seat, fasten seat belt,
start unit, turn auxiliary hydraulics “on”, and position
loader arms fully down.
8. At the control box, push on the “Tilt Up/Down”
toggle switch to tilt deflector spout up and pull toggle
switch to tilt deflector spout down. Watch spout to
make sure it moves in the proper direction.
9. At the control box, push on the “Rotate Left/Right”
toggle switch to rotate chute to the left and pull toggle
switch to rotate chute to the right. Watch chute to
make sure it rotates in the proper direction.
10. Shut skid steer/tractor down and make any needed
adjustments to the solenoid connections as follows:
• If spout tilts opposite of what it should, change
•
green wire connector (#3G) with red wire
connector (#3R) at solenoid (#2).
If chute rotates in the opposite of what it should,
change brown wire connector (#3B) with white wire
connector (#3W) at solenoid (#1).
Refer to Figure 2-4:
11. Adjust path of hydraulic hoses (#1, #2, #3) and wire
harness (#4) to suit and secure with cable ties (#5) as
needed.
Check Equipment Clearances
It is important to check clearance before putting the Snow
Blower into operation. Make sure hydraulic hoses and
wiring harness are long enough and won’t become
pinched or entangled in the equipment. Also, make sure
Snow Blower does not come in contact with tractor frame
and tires by carefully going through its full range of
motions.
1.
Visually inspect hydraulic hoses for possible pinch
points and shortness. If needed, make hose
adjustments before putting equipment into service.
2. Visually inspect wiring harness for possible pinch
points and shortness. If needed, make adjustments
to the wiring harness before putting equipment into
service.
IMPORTANT: Make sure hydraulic hoses and wiring
harness are long enough and properly secured so
that they do not become stretched or pinched
through their full range of motions.
3. If necessary, have someone stand nearby that can
motion for the operator to stop if a problem develops
while completing steps 4 thru 6 below.
4. Start skid steer/tractor and raise loader arms high
enough to tilt hitch plate fully down without Snow
Blower making contact with the ground.
5. Fully extend and retract hydraulic cylinders on the
end of the skid steer/tractor loader arms while
watching for interferences between skid steer/tractor
and Snow Blower frame.
6. Raise skid steer/tractor loader arms fully up and
repeat steps 4 thru 5 above.
3/18/15
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
13
Table of Contents
Section 2: Equipment Hook-up & Unhook
Unhooking The Snow Blower
Refer to Figure 2-5:
1. See “Long Term Storage” on page 31 before
parking Snow Blower for long periods.
1.
Park skid steer/tractor on a flat, level, solid surface,
and lower Snow Blower onto the surface.
2. Place transmission in park, set park brake, shut
power equipment off, and remove switch key.
3. With Snow Blower resting on the ground, release all
hydraulic system pressure before dismounting skid
steer or tractor. See Skid Steer Operator’s Manual for
instructions on how to release skid steer hydraulic
system pressure.
4. Disconnect solenoid wire harness (#4) from the front
of the loader arm. Do not disconnect harness from
the solenoids.
5. Disconnect hydraulic hoses (#1, #2, & #3) from skid
steer or tractor mounted hydraulic reservoir.
6. Store hydraulic hoses and wire harness on the Snow
Blower frame to keep dirt away from the couplings
and electrical connector.
7.
Raise lock pins on loader hitch. If lock pins are
activated from the operator’s seat, return to the skid
steer/tractor to raise lock pins.
8. From the operator’s seat, tilt top of loader hitch
slightly forward towards the Snow Blower.
9. Slowly lower skid steer/tractor hitch plate until top
angle bars and hitch plate have separated.
10. Back skid steer/tractor slowly away from the Snow
Blower while making sure it does not interfere with
the equipment.
4
3
2
1
5
Top Angle Bars
Bottom slots
35599
Hook-up to Snow Blower
Figure 2-5
3/18/15
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
14
Table of Contents
Section 3: Options
Section 3: Options
37223
37231
Motor assembly for units with S/N- & below
Motor assembly for units with S/N + & above
Motor Assembly
Figure 3-1
Motor Assembly
Refer to Figure 3-1:
MOTOR BUNDLE HYD 12-19 GPM . . . . . . . . 370-253A
MOTOR BUNDLE HYD 20-26 GPM . . . . . . . . 370-254A
MOTOR BUNDLE HYD 27-33 GPM . . . . . . . . 370-255A
Three impeller motor assembly options are available to
meet your hydraulic flow requirements. They are
interchangeable and do not require adapter kits.
Compare your motor’s GPM rating located on an
attached decal with the GPM ratings above.
If your Snow Blower’s impeller motor is not compatible
with your skid steer or tractor, you should replace it with
one of the above assemblies that is compatible.
37219
Flat Face Couplers
Refer to Figure 3-2:
The following flat face hydraulic couplers are available.
LARGE FLAT FACE COUPLERS . . . . . . . . . 316-289A
Large flat face couplers consist of one large flat face male
coupler and one large flat face female coupler
SMALL FLAT FACE COUPLERS. . . . . . . . . . 316-290A
Small flat face couplers consist of one small flat face
male coupler, one small flat face female coupler, and two
adapters.
Quick Release Couplers
Figure 3-2
Case Drain Coupler & Cable Ties
Refer to Figure 3-3:
CTL/SS COUPLER PACKAGE . . . . . . . . . . . 326-474A
When needed, order this optional 3/8” female quick
disconnect coupler for attaching to the Snow Blower’s
case drain line. Included with this package are three
cable ties for supporting the case drain line along its path
to the tank/sump.
3/18/15
35808
Case Drain Coupler
Figure 3-3
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
15
Table of Contents
Section 3: Options
Electrical Control Harness (Optional)
Land Pride offers six electrical control harness. If not purchased with the Snow Blower, one may be purchased from
your nearest Land Pride dealer. Additional instructions are provided on the page noted in the list below.
• Land pride Part No. 370-336A - - - - - - - - Control harness with Deutsch 14 pin 2 function power plug. 
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Refer to “Control Harness With Deutsch 14 Pin Plug” below.
• Land Pride Part No. 370-337A - - - - - - - - Control harness with Deutsch 14 pin 2 function power plug. 
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Refer to “Control Harness With Deutsch 14 Pin Plug” below.
• Land Pride Part No. 370-338A - - - - - - - - Control harness with Deutsch 14 pin 2 function power plug. 
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Refer to “Control Harness With Deutsch 14 Pin Plug” below.
• Land Pride Part No. 370-434A - - - - - - - - Control harness with Deutsch 2 pin plug and control box for Skid Steers. 
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Refer to “Control Harness With Deutsch 2 Pin Plug” on page 17.
• Land Pride Part No. 370-133A - - - - - - - - Tractor Control harness, connects direct to a 12V power source. 
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Refer to “Tractor Control Harness With 2 Eyelets” on page 18.
• Land Pride Part No. 370-134A - - - - - - - - Skid Steer Control harness, connect direct to a 12V power source. 
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - Refer to “Skid Steer Control Harness With 2 Eyelets” on page 19.
Kubota offers two controllers for operating the Powered Rake attached to a Kubota compact track loader or skid steer
loader. See your nearest Kubota dealer to purchase one of their controllers.
• Kubota Part No. V0511-97010 - - - - - - - - SVL Electrical connector (2 functions)
• Kubota Part No. W/G S6699 - - - - - - - - - SVL Multifunction handle (7 functions.)
Control Harness With Deutsch 14 Pin Plug
Refer to Figure 4-3:
Three 14 pin wiring harnesses are available. They attach
to the Snow Blower solenoids and skid steer 
14 pin coupler. Included with the wiring harnesses are
three cable ties. Pick the one that is designed for your
particular skid steer.
370-336A
Deutsch HD30 14 Pin 2 Function
This harness will work with the following skid steers:
370-337A
Deutsch HGD30 14 Pin 2 Function
This harness will work with the following skid steer:
• John Deere with 14 pin coupler
370-338A
Deutsch HGD30 14 Pin 2 Function
This harness will work with the following skid steer:
• John Deere “EH” with 14 pin coupler
35358
• Bobcat with 14 pin coupler
• GEHL with 14 pin coupler
• Kubota with 14 pin coupler
• Komatsu with 14 pin coupler
• Mustang with 14 pin coupler
• Takeuchi with 14 pin coupler
• Volvo with 14 pin coupler
It will also work with the following skid steers by reversing
the red and green wires at the solenoid:
• Case-Post 9/1/01 with 14 pin coupler
• Case-400 Series with 14 pin coupler
• New Holland with 14 pin coupler
16
Deutsch HGD30 14 Pin 2 Function Wiring Harness
Figure 4-3
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 3: Options
See Figure 4-1
on page 20.
37145
Toggle Switch Control Harness For Kubota CTL Skid Steers
Figure 3-5
Control Harness With Deutsch 2 Pin Plug
Refer to Figure 3-5:
370-434A
Kubota CTL Skid Steer Control Harness
This harness is used with skid steers equipped with a
Deutsch 2 pin coupler but not the Deutsch HD30 14 pin
coupler. It consist of the following:
7
1
Refer to Figure 3-5:
• Power cord (#1): Attach Deutsch 2 pin plug (#1) to
Kubota’s CTL male plug (#7) located behind the
driver’s seat.
Refer to Figure 3-6:
• 10 amp Fuse (#8): Fuse (#8) is supplied by customer.
Install 10 amp fuse (#8) in Kubota’s fuse box slot #17
labeled “Electrical Outlet-2”.
Refer to Figure 3-5:
• Power cord (#1): Attaches opposite end of the power
cord (#1) to control box (#2).
37389
Kubota Power Connection (Located Behind Drive Seat)
Figure 3-5
• Control box (#2): Mounts in a convenient location for
the operator to access from the operator’s seat.
• Wire harness (#3): Attaches to control box (#2) and
runs from the control box to the loader arm.
• Wiring harness (#4): Attaches to wire harness (#3) at
8
the loader arm and at the solenoids on the Snow
Blower.
• Cable ties (#5): For securing wire harnesses 
(#1, #3, & #4) to the skid steer and Snow Blower.
• Installation Manual 370-452M: Installation Manual, not
shown, is included with the Kit.
37390
Installation of 10 amp Fuse
Figure 3-6
3/18/15
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
17
Table of Contents
Section 3: Options
20 AMP FUSE
See Figure 4-1
on page 20.
TWO EYELETS
CONNECTS TO 12V
POWER SOURCE
FOUR CONNECTORS THIS END
CONNECTS TO EQUIPMENT SOLENOIDS
35809
Tractor Mounted Toggle Switch Control Harness
Figure 3-4
Tractor Control Harness With 2 Eyelets
Refer to Figure 3-4:
370-133A
CONTROL HARNESS TRACTOR
This harness is used only with tractor mounted Snow
Blowers and consist of the following:
• Power cord (#1): Attaches to tractor battery and control
box (#2).
• Control box (#2): Mounts in a convenient location for
the operator to access from the seat. See also Figure
4-1 on page 20.
• Wire harness (#3): Attaches to control box (#2) and
terminates at the front of one of the loader arms.
• Wiring harness (#4): Attaches to wire harness (#3) and
solenoids at the Snow Blower.
• Cable ties (#5): For securing wire harnesses (#1, #3, 
& #4) to the tractor loader and Snow Blower.
Installation Instructions for Tractor Harness
1.
Before doing anything else, determine the path
power cord (#1) will travel from tractor battery to
control box (#2), location of control box (#2), and
path wire harness (#3) will travel from control box to
the front end of the loader arm. Make sure control
box is mounted in an area where the operator can
operate the toggle switches easily from the tractor
seat. Method of mounting the control box is to be
determined by the customer.
2. Disconnect negative ( - ) black power cord from its
battery post.
3. Attach positive ( + ) red wire eyelet on end of power
harness (#1) to the battery’s positive ( + ) post and
tighten fastener hardware.
4. Attach negative ( - ) black wire eyelet on end of power
harness (#1) and negative ( - ) black power cord to
the battery’s negative ( - ) post and tighten.
5. Route power cord (#1) from the battery to the
predetermined location of control box (#2).
6. Mount toggle switch control box (#2) to the tractor
using hardware furnished by customer.
7.
Plug power cord (#1) and wire harness (#3) to control
box (#2).
8. Route wire harness (#3) to the front end of one of the
loader arms.
9. Make any final adjustments to wire harness (#3) and
power cord (#1) and make sure wire harness (#4)
can reach from solenoids at the Snow Blower to
connector at the end of wire harness (#3).
10. Secure power cord (#1) and wire harness (#3) with
cable ties (#5).
11. Connect 6 pin connector on end of wire harness (#4)
to wire harness (#3).
12. Continue with step 4 under “Solenoid Hook-up” on
page 12.
18
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 3: Options
See Figure 4-1
on page 20.
2 EYLETS
CONNECTS TO 12V
POWER SOURCE
20 AMP FUSE
4 CONNECTORS THIS END
CONNECTS TO EQUIPMENT SOLENOIDS
35246
Toggle Switch Control Harness
Figure 3-7
Skid Steer Control Harness With 2 Eyelets
Refer to Figure 3-7:
370-134A
Skid Steer Control Harness
This harness is used with skid steers not equipped with a
Deutsch HD30 14 pin or 2 pin coupler. It consist of the
following:
• Power cord (#3): Attaches to skid steer battery and
control box (#6).
• Control box (#6): Mounts in a convenient location for
operator to access from the seat. See also Figure 4-1
on page 20.
• Wire harness (#2): Attaches to control box (#6) and
runs from control box to rear of the loader arm.
• Wire harness (#1): Attaches to wire harness (#2) at the
rear of the loader arm and travels along the loader arm
to the front of the loader arm.
• Wiring harness (#4): Attaches to wire harness (#1) at
the loader arm and solenoids at the Snow Blower.
• Cable ties (#5): For securing wire harnesses 
37221
(#1, #2, #3, & #4) to the skid steer and Snow Blower.
Outer Skid Shoes
Figure 3-9
• Installation Manual 370-349M: (not shown)
Outer Skid Shoes
Refer to Figure 3-9:
Outer skid shoes are mounted on the outside of the side
panels and are adjustable by unbolting them and
reattaching them at a different height.
370-451K
370-438K
BUNDLE
SBL2566 SKID SHOE BUNDLE
SBL2574 & SBL2584 SKID SHOE
Inner Skid Shoes
Refer to Figure 3-10:
Inner skid shoes are mounted behind the Snow Blower
and are adjustable vertically by pulling a bent pin and
moving the skid shoes up or down.
370-440K
3/18/15
SKID SHOE BUNDLE
37222
Inner Skid Shoes
Figure 3-10
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
19
Table of Contents
Section 4: Adjustments
Section 4: Adjustments
Discharge Chute & Spout Deflector
!
WARNING
Never rotate chute or spout to throw snow at the tractor,
animals, or people. The Snow Blower is capable of picking up
large solid objects and discharging them out the spout causing
serious bodily injury or death.
IMPORTANT: Never operate a Snow Blower with
chute throwing snow towards property such as
vehicles, buildings, trailers etc. that can be
scratched, dented or broken by thrown projectiles.
IMPORTANT: Never operate a Snow Blower that can
throw snow towards the skid steer/tractor and/or
operator. If this can happen, make sure the chute
rotation stop is properly repaired before putting the
Snow Blower back into service.
IMPORTANT: Adjustment screws on hydraulic motor
are preset at the factory. Do not change factory
settings. Changing factory settings can cause
structural damage to the Snow Blower.
37220
Chute Rotation Gear Adjustment
Figure 4-2
Chute Rotation Gear Alignment
Refer to Figure 4-2:
IMPORTANT: Gear guard (#4) is shown removed for
clarity only. This adjustment can be made without
removing the gear guard. Should the guard be
removed, make certain gear guard (#4) is replaced
before putting Snow Blower back into service.
35810
1.
Stop skid steer/tractor, place in park, shut engine off
and remove switch key.
2. Loosen all three hex head bolts (#6). Do not remove.
3. Move hydraulic motor mount (#3) as needed until
drive gear (#2) has full tooth engagement with driven
gear (#1).
4. Hold hydraulic motor mount (#3) in this position and
tighten all three 3/8"-16 GR5 hex head bolts (#6) to
the correct torque.
Connects to 12V
Power Source
Not Used
Connects to Wire
Harness
Control Switches for Chute Rotation & Spout Deflector
Figure 4-1
Spout Deflector Adjustment
Refer to Figure 4-1:
The end of the spout can be angled up or down to direct
blown snow close or far away.
1.
Stop skid steer/tractor and place in park before
adjusting spout deflector.
If removed, be sure to replace gear guard (#4) with
existing 10-24 pan screws (#5), star washer (#7), and flat
washer (#8). Tighten pan screws (#5).
Chute Rotation Adjustment
Refer to Figure 4-1:
1. Stop skid steer/tractor and place in park before
adjusting chute rotation angle.
2. Push on “Rotate Left/Right” toggle switch to rotate
chute to the left and pull toggle switch to rotate chute
to the right.
3. Resume snow blowing once new chute angle is set.
2. Push on “Tilt Up/Down” toggle switch to tilt deflector
spout up and pull toggle switch to tilt deflector spout
down.
3. Resume snow blowing once new angle is set.
20
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 4: Adjustments
35607
37224
Outer Skid Shoe Assembly
Figure 4-3
Inner Skid Shoe Assembly
Figure 4-4
Outer Skid Shoe Adjustment
Inner Skid Shoe Adjustment
Refer to Figure 4-3:
Refer to Figure 4-4:
IMPORTANT: Surfaces with gravel or crushed rock
will require setting the skid shoes to carry the Snow
Blower higher than when on hard flat surfaces such
as asphalt and concrete. Never set Snow Blower so
low as to pick-up gravel and/or rock.
1.
Park on a level solid surface, place skid steer/tractor
in park, and lower both ends of grader blade (#1)
onto support blocks (#5) that are capable of holding
skid shoes (#2) off the ground several inches.
2. Shut skid steer/tractor engine off and remove switch
key.
3. On the right-hand side, remove hex flange lock 
nuts (#4) and carriage bolts (#3).
4. Adjust skid shoe (#2) up to set grader blade closer to
the ground and down to set grader blade farther away
from the ground.
5. Reinsert existing 1/2"-13 GR5 carriage bolts (#3) into
the square holes “A” that line up with Snow Blower
frame. Secure carriage bolts (#3) with hex flange lock
nuts (#4).
IMPORTANT: Surfaces with gravel or crushed rock
will require setting the skid shoes to carry the Snow
Blower higher than when on hard flat surfaces such
as asphalt and concrete. Never set Snow Blower so
low as to pick-up gravel and/or rock.
1.
Park on a level solid surface, place skid steer/tractor
in park, and lower both ends of grader blade onto
support blocks or jack stands that are capable of
holding inner skid shoes (#1) off the ground 3 or 4
inches.
2. Shut skid steer/tractor engine off and remove switch
key.
3. On the left-hand side, remove hairpin cotter (#2) and
bent pin (#3).
4. Adjust skid shoe (#1) up to set grader blade closer to
the ground and down to set grader blade farther away
from the ground.
5. Reinsert existing bent pin (#3) and secure with
hairpin cotter (#2).
6. Repeat steps 3 thru 5 for the right-hand side.
6. Tighten hex flange lock nuts (#4) to the correct
torque.
7.
Repeat steps 3 thru 6 for the left-hand side.
3/18/15
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
21
Table of Contents
Section 4: Adjustments
o
37228
35811
Impeller & Auger Speed
Figure 4-5
Auger Speed
Refer to Figure 4-5:
The auger speed can be changed to customer
preference.
1.
1.
Park on a level solid surface, place skid steer/tractor
in park or set park brake, disengage hydraulics if skid
steer mounted or PTO if tractor mounted, lower
loader arms and Snow Blower fully down, shut
engine off, remove switch key, and wait for impeller
and auger to come to a complete stop before
dismounting from skid steer/tractor.
Loosen knob (#3) on flow control valve (#1).
2. Rotate knob (#3) to a higher number on the gradient
scale (#2) to decrease auger speed and to a lower
number to increase auger speed.
3. Retighten knob (#3) to keep it from moving.
Reading Level Run Indicator
Figure 4-6
Level Run Indicator Adjustment
Refer to Figure 4-6:
IMPORTANT: In order for the level run indicator to be
adjusted accurately, the skid steer or tractor with
attached Snow Blower must be parked on ground
that is flat and level.
1.
Park skid steer/tractor on flat level ground.
2. Lower lift arms to put attachment flat on the ground.
3. Make any tilt adjustments as necessary to position
top of Snow Blower side plate parallel and level with
the ground. If necessary, a level (#4) can be used as
shown.
4. Turn off engine, engage park brake, and remove key
to prevent unauthorized starting before dismounting
from skid steer or tractor.
5. If included, raise seat bar and move controls until
both lock.
6. Loosen hex flange lock nuts (#2) and adjust level run
indicator (#3) until indicator arrow (#1) points to
“LEVEL RUN”.
7.
Hold level run indicator (#3) in this position and
tighten hex flange lock nuts (#2) to the correct torque.
NOTE: The level run indicator should not need
readjusting unless indicator has been forcibly
moved, mounting hardware has come loose, or a
different skid steer is hitched to the Snow Blower.
8. Repeat steps 1 thru 7 if attaching Snow Blower to a
different skid steer.
22
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 5: Operating Instructions
Section 5: Operating Instructions
Introduction
Hazard control and accident prevention are dependent
upon the awareness, concern, prudence, and proper
training involved in the operation, transport, storage, and
maintenance of the Snow Blower. Therefore, it is
absolutely essential that no one operates the Snow
Blower without first having read, fully understood, and
become totally familiar with the Operator’s Manual. Make
sure the operator has paid particular attention to:
• Important Safety Information, pages 1 to 4
• Section 1: Assembly & Set-up, page 7
• Section 2: Equipment Hook-up & Unhook, page 11
• Section 4: Adjustments, page 20
• Section 5: Operating Instructions, page 23
• Section 6: Maintenance & Lubrication, page 29
The following inspection should be performed before
using the Snow Blower.
Operating Checklist
✔
Check
Make sure all guards and shields are in place. 
Refer to “Important Safety Information”.
Ref.
Page 1
Read and follow hook-up & preparation instructions.
Refer to “Snow Blower Hook-up”.
Page 11
Make all required adjustments. 
Refer to “Section 4: Adjustments”.
Page 20
Read and follow all operating procedures. 
Refer to “Section 5: Operating Instructions”.
Page 23
Read and follow all maintenance instructions.
Refer to “Section 6: Maintenance & Lubrication”.
Page 29
Make sure there are no hydraulic leaks. 
Refer to “Avoid High Pressure Fluids Hazard”.
Page 3
Lubricate Snow Blower as needed.
Refer to “Lubrication”.
Page 32
Check Snow Blower initially and periodically for loose
bolts and pins. Refer to “Torque Values Chart”.
Page 36
Pre-Operational Safety Check
Make the following inspections with Snow Blower resting
on the ground while attached to a skid steer or tractor.
Place skid steer/tractor in park or set park brake,
disengage hydraulics, disengage PTO if tractor mounted,
lower loader arms fully down, remove switch key and
make sure impeller and auger have come to a complete
stop before dismounting skid steer or tractor:
1.
Complete Operating Checklist table provided above.
2. Inspect skid steer/tractor safety equipment to make
sure it is in good working condition and that all safety
alert decals are visible and readable. Replace all
missing and unreadable safety alert decals.
3. Inspect hitch hook-up to Snow Blower. Make sure
skid steer or tractor hitch is secured under the Snow
Blower’s top angle bars, lock pins extend fully
through bottom slots in Snow Blower hitch, and
handles are locked down.
3/18/15
4. Inspect wiring harness and connection points before
starting the machine. Make sure wire harness and
connections are not pinched, frayed, or broken and
that they will not come in contact with moving parts.
5. Inspect hydraulic hoses, fittings, and valves before
starting the machine. Make sure hoses are not
pinched, kinked, twisted, or frayed and that they will
not come in contact with moving parts.
6. Check for and remove foreign objects wrapped
around auger and impeller.
7.
Check for bent, broken, and extreme wear on auger
flighting and impeller. Repair or replace auger and
impeller as required.
8. Check skid shoes for wear. Replace skid shoes as
needed. See “Outer Skid Shoe Option” on page 30
for replacement instructions.
9. Verify skid shoes are set at the correct height. Refer
to “Outer Skid Shoe Adjustment” or “Inner Skid
Shoe Adjustment” on page 21.
Operational Safety Check
The remaining inspections are made with the skid steer
or tractor engine running.
1.
Start skid steer or tractor and set throttle to idle or
slightly above idle.
2. Operate hydraulic controls to verify control lever
movements function properly and equipment
movements are correct.
3. Shut skid steer or tractor down properly and make
any necessary changes to the controls before
continuing.
4. Operate Snow Blower loader arms through their full
range of movements to check for clearances. Refer
to “Check Equipment Clearances” on page 13.
!
WARNING
Stop hydraulics immediately if auger or impeller makes
contact with Snow Blower housing. Wait for impeller and
auger to come to a complete stop before dismounting from skid
steer or tractor to check for probable causes. Make necessary
repairs before continuing on.
5. With skid steer throttle set to idle or slightly above
idle, slowly engage hydraulics to the Snow Blower.
6. Once Snow Blower is running smoothly, increase
impeller and auger speed. Disengage hydraulics
immediately if any unusual sound or vibration is
noticed.
a. Shut skid steer or tractor down properly and
investigate cause of noise.
b. Make repairs before putting Snow Blower back
into service.
7.
Shut Snow Blower down after it has been operating
smoothly at full speed for several minutes.
8. This completes the operational safety checks.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
23
Table of Contents
Section 5: Operating Instructions
General Safety Information
!
DANGER
Always secure underside of Snow Blower with solid supports
before working under the unit. Never work under equipment
supported by hydraulics. Hydraulics can drop equipment if
controls are actuated or if hydraulic lines burst. Either
situation can drop the Snow Blower instantly even when
power to hydraulics is shut off.
A crushing hazard always exists around equipment attached to
a skid steer or tractor with loader arms. Loader arms and
hydraulic cylinders can pinch and/or crush causing serious
injury or death.
• The operator must know how to control the skid steer or
tractor and how to stop it and attached equipment quickly
in an emergency.
• Do not drive up to anyone standing in front of a fixed object
such as a wall or bench. Never assume that the brakes will
stop the machine in time.
• Never allow anyone to go near the attached equipment or
under the unit when arms are raised.
• When equipped, sound horn before traveling in reverse.
Drive at a slower speed to compensate for blind spots.
!
DANGER
All guards and shields must be installed and in good working
condition at all times during Snow Blower operation.
!
DANGER
Always place skid steer/tractor in park or set park brake,
disengage hydraulics, disengage PTO if tractor mounted,
lower loader arms fully down, shut engine off, remove switch
key, and wait for impeller and auger to come to a complete
stop before dismounting from the skid steer or tractor.
!
DANGER
Always operate attached implement while seated in the skid
steer/tractor cab with Roll-Over Protective Structure (ROPS)
and seat belt fastened around the operator. Operator can
become pinched, crushed, or entangled if not seat belted in or
if operating equipment from outside the cab.
!
DANGER
Keep people and animals away from machinery while in
operation. They can become entangled in the Snow Blower
auger or be ran over by the skid steer/tractor and/or Snow
Blower causing serious injury or death.
!
DANGER
Make certain the Snow Blower is resting on the ground and all
hydraulic pressure is relieved before disconnecting hydraulic
fittings from the Snow Blower.
24
DANGER
DANGER
The operator should be a person who is responsible,
physically capable, and properly trained to operate this Snow
Blower. They should read and understand all instructions in
this Operator’s Manual. Anyone not properly trained and all
children under the age of 16 should not operate this machine.
!
!
Always operate Snow Blower with skid steer/tractor flashing
lights turned on. Be extremely careful blowing snow at night
with rear bright lights on. Approaching traffic from either
direction can mistake which traffic lane you are traveling in
and your direction of travel.
!
!
DANGER
DANGER
Do not operate and/or travel across steep inclines where a
skid steer or tractor can slip or roll-over causing serious
injury or death. Consult your skid steer or tractor Operator’s
Manual for acceptable inclines the machine is capable of
traveling across.
!
DANGER
Hydraulic fluid under high pressure can penetrate skin. Wear
protective gloves and safety glasses or goggles when working
with hydraulic systems. Use a piece of cardboard or wood
rather than hands when searching for hydraulic leaks. If
hydraulic fluid is injected into the skin or eyes, it must be
treated by a doctor familiar with this type of injury within a
few hours or gangrene may result. DO NOT DELAY.
!
DANGER
Always shut down hydraulics and wait for all rotating
components to come to a complete stop before cleaning out a
plugged discharge chute. The impeller blades are located just
below the chute and will nip off body extremities and cause
serious injuries or death even when using a stick or other
object to unplug the chute.
!
DANGER
Always shut down hydraulics and wait for all rotating
components to come to a complete stop before attempting to
unclog built-up snow from the auger or impeller, make
adjustments, perform maintenance, or clean the Snow Blower.
Rotating impeller, auger, and chain drive can cause serious
bodily injury or death.
!
DANGER
Never run gravel, crushed rock, or other solid objects through
the Snow Blower. Doing so will result in an expensive breakdown. The Snow Blower is also capable of throwing solid
objects at high speeds causing property damage and injury or
death to animals and people.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 5: Operating Instructions
!
DANGER
Never allow riders including children on the skid steer/tractor
or Snow Blower. They can become entangled in the machinery
or fall and be ran over causing serious injury or death.
!
DANGER
Never work around or make contact with utilities such as gas
lines, electrical lines, or other hazards that can cause serious
injury or death from electrocution, explosion, or fire.
!
WARNING
Always be aware of pedestrians and vehicle traffic. Move
snow during low-traffic hours. Adjust chute to correct
trajectory due to wind that will not create a driving hazard for
all other vehicles. Always exercise safety, courtesy, and
common sense.
!
WARNING
!
WARNING
Always dress to stay warm in cold weather. Use a skid steer or
tractor equipped with a cab to help stay warm and to protect
against cold blowing snow. Never allow your body or
extremities to become too cold. Go inside to warm-up if you
are getting too cold.
Always travel removing snow at a speed that allows the
operator to be in control at all times and always be ready to
make emergency stops. Snow removal speed will vary
depending on depth of snow, snow moisture, and how tight the
snow is compacted.
!
WARNING
Beware of obstacles along side the skid steer/tractor while
making turns when backing up. Never swing front of tractor or
tractor mounted Snow Blower into fire hydrants, mailboxes,
buildings, vehicles, fences, trees, or other standing obstacles.
! WARNING
Clear area to be worked of debris and other unforeseen
removable objects before blowing snow. Mark any potential
hazards that cannot be removed such as tree stumps, posts,
rocks, holes, and drop-offs with a visible flag. The Snow
Blower is capable of throwing solid objects at high speeds
causing property damage and serious bodily injuries, or death
to animals and people.
! WARNING
Do not remove snow from an icy surface unless skid steer or
tractor is properly equipped for working on such a surface.
Always proceed with caution when traveling on ice. An icy
surface covered with snow will result in loss of traction and
steering control.
3/18/15
!
WARNING
!
WARNING
Dress properly for the job. Do not wear loose fitting clothing
or clothing with pull strings such as hooded sweat shirts. Also,
keep long hair tucked in. Loose clothing, pull strings, and long
hair can become entangled in rotating parts causing serious
injury or death. Wear footwear that will improve footing on
slippery surfaces. Always be sure of your footing and keep a
firm hold on handles. Walk, never run.
Do not abuse equipment. Incorrect use of skid steer or tractor
and Snow Blower can damage equipment structurally and
cause serious injury or death.
• Check hook-up points frequently to make sure tractor hitch
is properly positioned under the top angle bar, locking pins
are seated in their notches, handles are locked down, and
equipment is in good operating condition.
• Do not carry, lift loads, or use Snow Blower as a working
platform. Doing so can cause serious injury or death.
• Do not use Snow Blower for pulling objects out of the
ground, for digging into the ground, for prying other
objects, or for pushing and towing other equipment.
• Do not use skid steer/tractor loader arms for lifting front
end of the skid steer or tractor off the ground. Doing so can
damage equipment and cause injury if exceeding lift
capacity of unit.
• The parts on your Snow Blower have been specially designed
and should only be replaced with genuine Land Pride parts.
Altering the Snow Blower can adversely affect its
performance and/or reliability.
!
WARNING
!
WARNING
!
WARNING
!
WARNING
Do not operate Snow Blower with auger flighting or impeller
blades that are broken or bent making contact with the
housing. Broken or bent flighting and blades can break loose
at high speeds causing serious injury or death.
Do not operate Snow Blower with loose pins, bolts, and nuts.
Loose hardware can result in a serious breakdown causing
bodily injury or death.
If required, use back-up alarm to warn others you are backing
up. Always comply with all federal, state, and local laws.
Keep people and animals away while removing snow. Never
operate Snow Blower with chute throwing snow toward
people, animals, or operator. The Snow Blower is capable of
picking up large solid objects and discharging them at high
speeds causing serious bodily injury or death.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
25
Table of Contents
Section 5: Operating Instructions
!
WARNING
!
WARNING
!
WARNING
Keep body extremities, loose clothing, and pull strings away
from hydraulically driven chute rotation. Especially keep
away from sprocket teeth that can pinch and crush fingers and
hands.
Never operate Snow Blower without good visibility and light.
Use a skid steer or tractor equipped with a cab to keep snow
from being blown by the wind into the operator’s face.
Never pile snow where it obstructs visibility of traffic. Never
pile snow near fire hydrants, mailboxes, water drains, shut-off
valves, electrical boxes, and handicap parking areas.
! WARNING
Never remove snow that has been plowed. Plowed snow
contains foreign particles such as dirt and rocks that can
damage the unit and cause serious bodily injury or death.
!
WARNING
Blow only fresh snow with the Snow Blower. Blowing other
materials can damage the unit and cause serious bodily injury
or death.
!
CAUTION
Do not exceed Snow Blower specifications for maximum
hydraulic pressure rating and gallons per minute rating.
Personal injury and/or machine damage can occur.
IMPORTANT: Never operate Snow Blower with
chute throwing snow toward property such as
vehicles and buildings that can be scratched,
dented, or broken by solid objects hitting them.
IMPORTANT: Do not use Snow Blower as a Box
Scraper or to blow other materials. Doing so can
break the auger, impeller, and cause structural
damage to the unit.
NOTE: Always check with local codes to know
where snow can be legally piled. Never pile snow on
someone else’s property, streets, or sidewalks.
26
35559
Safety Steps
Figure 5-1
Mounting & Dismounting Skid Steer
Refer to Figure 5-1:
!
WARNING
Use stepping pads, grab-handles, and anti-slip surfaces when
getting on or off the skid steer. Using unapproved surfaces and
handles to mount and dismount can result in a falling hazard
and cause serious injury or death.
Transporting
!
WARNING
Follow all safety precautions when transporting. Not using
safe transporting methods can damage the equipment and
cause death or serious injury.
• Always transport with attached equipment low to the
ground to maintain stability of the skid steer or tractor.
• Always travel straight up and straight down inclines. Make
turns only on level ground.
• Keep equipment away from electrical power lines. Place an
orange warning sign under overhead electrical power lines
indicating type of danger above.
• Transporting loads across inclines, over ramps, grades,
bumpy, soft, or slippery surfaces reduces machine stability.
Transporting in these conditions is extremely dangerous.
• When traveling on public roads at night or during the day,
use accessory lights and devices for adequate warning to
operators of other vehicles. Comply with all federal, state,
and local laws.
• When traveling on roadways, transport in such a way that
faster moving vehicles may pass you safely.
• Limit maximum transport speed to 20 mph. Reduce ground
speed when turning and leave enough clearance so Snow
Blower does not contact obstacles such as buildings, trees,
or fences.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 5: Operating Instructions
37227
General Operator Instructions
It is important that you familiarize yourself with the
Operator’s Manual, properly attach the Snow Blower to
your skid steer or tractor front loader, completed the
operating checklist and pre-operating safety check
before running the operational safety check.
You will want to park on a flat level surface and level your
Snow Blower to operate parallel to the ground before
making any operational safety checks or removing snow.
If you have not leveled the Snow Blower, please
complete this procedure before continuing.
If you detect a malfunction in either your Snow Blower or
skid steer/tractor during the operational safety check,
immediately shut skid steer or tractor off, remove switch
key, and make all necessary repairs and adjustments
before continuing.
Reading Level Run Indicator
Figure 5-2
Leveling The Snow Blower
Refer to Figure 5-2:
The level run indicator (#2) helps the operator to verify
the Snow Blower is operating parallel to the ground.
NOTE: Most tractor loaders have a leveling rod that
can be used in lieu of the level run indicator. Refer
to your tractor loader manual to properly adjust the
leveling rod. Leveling rod must be adjusted to
operate the Snow Blower parallel to the ground.
IMPORTANT: The level run indicator must be
adjusted correctly before using it. Refer to “Level
Run Indicator Adjustment” on page 22.
1.
Stop skid steer/tractor on a flat level surface and
lower loader arms until Snow Blower is close to
ground.
2. Extend or retract hydraulic cylinders on the end of the
skid steer/tractor loader arms until the indicator
arrow (#1) points to “LEVEL RUN”.
3. Lower Snow Blower until it is resting on its skid shoes
and make any final adjustments necessary to make
sure the indicator arrow (#1) still points to “LEVEL
RUN”.
IMPORTANT: The indicator arrow (#1) should point
to “LEVEL RUN” when parked on flat level ground
and Snow Blower is sitting on the ground. It is normal
for the indicator arrow to move from “LEVEL RUN”
during operation. DO NOT readjust hitch angle.
Doing so can cause the auger to contact the ground
and damage it.
4. Once set, DO NOT change position of the hydraulic
cylinders on the end of the skid steer/tractor loader
arms. See important note above.
5. Repeat steps 1 thru 4 if skid shoes are readjusted or
if hydraulic cylinders on end of skid steer/tractor
loader arms have been moved.
3/18/15
Before starting the skid steer or tractor, make sure your
machine is in park or in neutral and the park brake is set.
Turn hydraulic function off. If Snow Blower is tractor
mounted and powered by a rear mounted Hydraulic
Reservoir System (HRS), disengage tractor PTO to the
HRS.
IMPORTANT: Set loader arms to float before
blowing snow. The skid shoes can have increased
wear if loader arms are rigid.
With your Snow Blower resting on the ground and loader
arms set to float, start your skid steer or tractor and set
engine throttle speed at a low idle. Engage PTO if tractor
mounted with a rear mounted HRS. Turn hydraulics to the
Snow Blower on. If everything is running smoothly at a
low idle, slowly increase skid steer/tractor engine RPM
until the Snow Blower reaches full operating speed. If
everything is still running smoothly, return engine to low
idle, turn hydraulic function to off, and when applicable,
disengage PTO.
You should now be ready to transport to your snow
blowing site at a safe ground speed. On roadways
transport in such a manner that faster moving vehicles
can easily see you and pass you safely. Reduce your
speed when travelling over rough and hilly terrain. Avoid
quick or sharp steering corrections. Take extra care to
ensure that the Snow Blower doesn’t come into contact
with obstacles such as trees, buildings, or fences. Use
accessory lights and appropriate reflective devices to
provide adequate warning to pedestrians and other
vehicle operators when traveling on public roads and in
the dark of night. Comply with all local, state, and federal
laws.
It is important that you know the area where snow is to be
removed and what lies beneath the snow. If possible,
survey the area ahead of the snow. Remove all possible
obstructions and mark any obstructions that cannot be
removed with flags that project above the snow. If you are
unfamiliar with the area, ask someone who can identify
hidden obstructions so that you can mark them with a
flag. Flag manholes, water meters, gas meters, culvert
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
27
Table of Contents
Section 5: Operating Instructions
edges, fire hydrants, stumps, and other obstructions that
are not easily seen. It really pays to inspect a new area
and to develop a safe plan before moving snow.
Determine how close to the ground the Snow Blower can
be operated. Set skid shoes to hold the Snow Blower off
the ground at a predetermined height. Surfaces with
gravel or crushed rock will require a higher setting than
hard flat surfaces such as asphalt and concrete. Never
set Snow Blower so low as to pick-up gravel and/or rock.
Determine wind direction and devise a removal plan that
will allow wind to carry blown snow away from the
operator. Snow discharged out the Snow Blower and
blown back at you will obstruct your view and can totally
block your vision of work.
Determine direction to blow snow that will not create a
driving hazard for other vehicles and rotate chute to blow
snow in that direction. To minimize work, do not blow
snow over an area that has already been cleared of snow
and never rotate chute to blow snow toward the skid
steer/tractor and/or operator as hard objects can be
thrown from the discharge chute.
Set spout deflector angle. The angle will vary depending
on how far snow is to be blown, how light and fluffy the
snow is, and how wet and heavy it is.
Some adjustments to the chute rotation, spout deflector
angle, and skid shoe height may be necessary after
traveling a few feet. If you need to get off the skid steer or
tractor to make adjustments, you must stop your
machine, turn hydraulic functions off, disengage PTO
when applicable, place skid steer/tractor in park or in
neutral with park brake set, shut engine off, remove
switch key, and wait for all components to come to a
complete stop before dismounting your skid steer/tractor.
It is now time to position your Snow Blower at your
starting point. Once there, stop travelling and lower Snow
Blower down onto its skid shoes.
Set throttle at an idle speed, engage PTO if tractor
mounted, and turn hydraulic function on. Listen for
unusual clicking or knocking sounds as the auger and
impeller start rotating. If everything sounds fine increase
engine speed to a recommended operating speed. If an
unusual sound is heard, shut your machine down
immediately, investigate the cause, and make necessary
repairs before continuing.
snow while traveling at a speed that will allow you to be in
control at all times. Change speed if travel speed is too
fast. Only change to a higher speed if you are certain it
will be safe. The heavier and deeper the snow the slower
you will need to travel. If your unit is tractor mounted and
powered with a rear mount HRS, maintain recommended
PTO speed and use a lower gear selection to maintain
proper travel speed. If your unit is skid steer mounted,
you should set your high/low gear selection in the low
range and vary your engine speed to maintain proper
travel speed.
Do not use rear view mirrors to view direction of travel
while backing up. Instead, turn your head to look where
you are traveling. It is very important that you get a full
field of view to prevent an accident.
Beware of obstacles along side your machine while
making turns traveling forward and backing-up. Never
swing the Snow Blower into fire hydrants, mailboxes,
buildings, vehicles, fences, trees, or other standing
obstacles. Shift to a lower gear when possible and travel
very slow when in a tight situation to allow time to react.
Stop your skid steer or tractor before hitting an obstacle.
Once you have reached end of travel, stop your skid steer
or tractor, raise the Snow Blower up, and return to the
front of your work to make another run at blowing snow. It
is not necessary to disengage hydraulics while returning
to the front of your work.
Once at the front, line up your Snow Blower with your
next starting point, lower unit down onto its skid shoes
until all pressure is off the loader arms, and begin
traveling forward blowing snow.
With a little practice you will be pleased with what you and
your Land Pride Snow Blower can do. Whether you are
done blowing snow, need to take a break, or just need to
make a few adjustments to the Snow Blower, remember
to always do the following:
• Reduce engine rpm
• Shut hydraulic functions off
• Disengage PTO if tractor mounted
• Stop on level ground and set park brake
• Turn off the engine and remove the key
• Stay on the tractor until the Snow Blower auger and
rotor have come to a complete stop.
Start traveling forward while blowing snow. Always blow
28
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 6: Maintenance & Lubrication
Section 6: Maintenance & Lubrication
General Maintenance Information
Proper servicing and adjustment is key to the long life of
any implement. With careful inspection and routine
maintenance, you can avoid costly downtime and repair.
Check all bolts after using unit for several hours to be
sure they are tight. Replace any worn, damaged, or
illegible safety labels by obtaining new labels from your
Land Pride dealer.
The parts on your Snow Blower have been specially
designed and should only be replaced with genuine Land
Pride parts. Do not alter the Snow Blower in a way which
will adversely affect its performance.
Tractor/Skid Steer Maintenance
One of the most important things you can do to prevent
hydraulic system problems is ensure that your hydraulic
oil remains free of dirt and contamination.
35614
Impeller Inspection
Figure 6-1
Use a clean cloth to wipe hose couplings before attaching
them to your machine and replace hydraulic filter
elements at the prescribed intervals. These simple steps
will go a long way to prevent control valve and hydraulic
cylinder problems.
Auger & Impeller Inspection
Refer to Figure 6-1:
1. Check 2"-12 impeller nut (#3) for tightness. If loose,
tighten jam nut with wrench (#1). When finished,
secure wrench to housing with flange lock nuts (#2).
Refer to Figure 6-2:
2. Check impellers (#1) for wear, structural cracks, and
breakage. Repair or replace impeller before it causes
structural damage to Snow Blower housing.
3. Check for bent impeller blades (#1) that are making
contact or are about to make contact with Snow
Blower housing. Repair or replace impeller before it
causes structural damage to Snow Blower housing.
35608
Auger & Impeller Inspection
Figure 6-2
4. Check auger flighting (#3) and auger paddles (#2) for
wear, structural cracks, bending, and breakage.
Repair or replace auger before components breakoff and are sent into the impeller or through the air.
5. Check end bearing (#5) for wear. Replace bearings
that are worn excessively.
6. Lubricate bearings as required. See lubrication
schedule for “Auger Flange Bearing” on page 32.
7.
Check bearing mounting bolts (#4) for tightness.
Make certain they are tightened to the correct torque.
8. Refer to Figure 6-3: Check motor mounting 
bolts (#2 & #5) for tightness. If needed, tighten bolts
as follows:
a. Remove nuts (#4), bolts (#3), & motor cover (#1).
b. Tighten 1/2"-13 GR5 bolts (#2 & #5) to the correct
torque as needed.
35812
Motor Mount Inspection
Figure 6-3
c. Reattach motor cover (#1) with existing 1/4"-20
GR5 bolts (#3) and hex lock nuts (#4). Tighten
lock nuts to the correct torque.
3/18/15
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
29
Table of Contents
Section 6: Maintenance & Lubrication
35607
Outer Skid Shoe Replacement
Figure 6-4
37224
Outer Skid Shoe Assembly
Figure 6-5
Outer Skid Shoe Option
Refer to Figure 6-4:
Outer Skid Shoe Part Numbers
Part No.
Part Description
370-436H
370-437H
370-449H
370-450H
OUTER RIGHT-HAND SKID SHOE SBL66
OUTER LEFT-HAND SKID SHOE SBL66
OUTER RIGHT-HAND SKID SHOE SBL74/84
OUTER LEFT-HAND SKID SHOE SBL74/84
Inspect outer skid shoes for wear and replace as needed.
1.
Park on a level solid surface, place skid steer/tractor
in park or neutral with park brake set, lower Snow
Blower until it is approximately 6" above ground,
disengage hydraulics, and wait for all components to
stop rotating before dismounting skid steer/tractor.
Inner Skid Shoe Option
Refer to Figure 6-5:
Inner Skid Shoe Part Numbers
Part No.
Part Description
370-439H
INNER SKID SHOE
Inspect inner skid shoes for wear and replace as needed.
1.
Park on a level solid surface, place skid steer/tractor
in park, and lower both ends of grader blade onto
support blocks or jack stands that are, at a minimum,
8 1/2" high.
2. Shut skid steer/tractor engine off and remove switch
key.
2. Place 1 1/2" to 3" thick support block(s) (#5) under
the grader blade (#1) near the right-hand and lefthand skid shoes (#2).
3. On the left-hand side, remove hairpin cotter (#2),
bent pin (#3), and inner skid shoe (#1).
3. Return to the skid steer/tractor and lower the Snow
Blower onto the support blocks (#5), shut engine off
and remove switch key. Wait for all components to
stop rotating before dismounting skid steer/tractor.
5. Insert bent pin (#3) thru the same holes in the skid
shoe mount and new skid shoe that it was removed
from.
4. Reinsert new inner skid shoe (#1).
4. Count & record number of square holes “A” from top
down to the holes carriage bolts (#3) are located.
6. Secure bent pin with hairpin cotter (#2).
5. Remove hex nuts (#4), carriage bolts (#3), and righthand skid shoe (#2). Discard skid shoe and save
hardware for reattachment of new skid shoe.
8. If skid shoes need readjusting, refer to “Inner Skid
Shoe Adjustment” on page 21.
7.
Repeat steps 3 & 4 for the right-hand side.
6. Using the recorded number in step 4 above, insert 
1/2"-13 x 1 1/4" GR5 carriage bolts (#3) through
square holes “A” in skid shoe (#2) and the Snow
Blower side panel. Secure carriage bolts with hex
flange lock nuts (#4).
7.
Tighten lock nuts (#4) to the correct torque.
8. Repeat steps 4 to 7 above for left-hand skid shoe.
9. If skid shoes need readjusting, refer to “Outer Skid
Shoe Adjustment” on page 21.
30
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 6: Maintenance & Lubrication
!
DANGER
Always secure Snow Blower in the up position with solid
supports before servicing underside of Snow Blower. Never
work under equipment supported by hydraulics. Hydraulics
can drop equipment if controls are actuated or if hydraulic
lines burst. Either situation can drop the Snow Blower
instantly even when power to hydraulics is shut off.
1.
35609
Grader Blade Replacement
Figure 6-6
4. Repaint parts where paint is worn or scratched to
prevent rust. Ask your Land Pride dealer for aerosol
touch-up paint. Paint is also available in touch-up
bottles with brush, quarts, and gallon sizes by adding
TU, QT, or GL to the end of the aerosol part number.
Refer to Figure 6-6:
Grader Blade Part Numbers
Part No.
Part Description
1.
2.
3.
3.
3.
PLOW 5/8"-11 x 1 3/4" GR5
NUT HEX FLANGE LOCK 5/8"-11 PLT
SBL2566: GRADER BLADE 1/2" x 6" x 65 1/2"
SBL2574: GRADER BLADE 1/2" x 6" x 73 1/2"
SBL2584: GRADER BLADE 1/2" x 6" x 83 1/2"
NOTE: When front edge of grader blade (#3) is worn
excessively, it can be rotated 180o and reused to
extend its wear life.
Inspect cutting edge of grader blade and plow bolts for
wear and rotate 180o or replace as needed. Make sure
grader blade is replaced before auger housing becomes
exposed to wear.
1.
Remove hex flange lock nuts (#2), plow bolts (#1),
and grader blade (#3).
2. Attach new or rotated grader blade (#3) to bottom of
Snow Blower frame with existing/new plow bolts (#1)
and hex flange lock nuts (#2).
3. Tighten lock nuts to the correct torque.
Long Term Storage
Clean, inspect, service, and make necessary repairs to
the Snow Blower when parking it for long periods and
when parking it at the end of a working season. This will
help ensure the Snow Blower is ready for field use the
next time you hook-up to it.
!
DANGER
Land Pride Aerosol Touch-up Paint
Part No.
Part Description
821-011C
821-002C
821-066C
PAINT LP BEIGE AEROSOL SPRAY CAN
PAINT LP BLACK AEROSOL SPRAY CAN
PAINT ORANGE AEROSOL SPRAY CAN
5. Replace all damaged or missing decals.
6. Lubricate as noted under “Lubrication” on page 32.
7.
Apply a coating of oil to the areas without paint due to
high wear to minimize oxidation.
8. Store Snow Blower on a level surface in a clean, dry
place. Inside storage will reduce maintenance and
make for a longer Snow Blower life.
9. Follow all “Unhooking The Snow Blower”
instructions on page 14 when disconnecting Snow
Blower from skid steer/tractor.
Ordering Replacement Parts
Land Pride offers equipment in factory standard beige
with black highlights. Equipment may also be purchased
in orange. Special attention must be given to the part
number to prevent ordering the wrong color. A suffix
number corresponding to one of the colors below must be
added at the end of the part number. Parts ordered
without the suffix number will be supplied in factory
standard colors.
82 . . . . . . Orange
Always disconnect driveline from tractor PTO before
servicing drive train components or underside of unit. Snow
Blower can be engaged if tractor is started causing bodily
injury or death.
3/18/15
2. Check impeller, auger, wear bars, and skid shoes for
wear and breaks. Repair or replace if necessary. See
“Auger & Impeller Inspection” on page 29.
3. Inspect for loose, damaged, or worn parts. Make
adjustments, repairs, and/or replace as needed.
Grader Blade
802-206C
803-263C
820-042C
820-477C
820-046C
Clean off any dirt and grease that may have
accumulated on the Snow Blower and moving parts,
and then wash surface thoroughly with a garden hose.
85 . . . . . . . Black
For example, if you are ordering a replacement part with
part number 555-555C and the existing part is orange,
then add the suffix 82 to the end of the number to make
the part number read 555-555C82.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
31
Table of Contents
Section 6: Maintenance & Lubrication
Lubrication
Lubrication
Legend
Multi-purpose 
spray lube
Multi-purpose 
grease lube
Multi-purpose 
oil lube
50
Hrs
Intervals in hours at which
lubrication is required
10
Hours
Auger Flange Bearing
2 - Zerks: Left Side Shown
Type of Lubrication: Multi-purpose Grease
35610
32
Quantity = As needed
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 7: Specifications & Capacities
Section 7: Specifications & Capacities
SBL25 Series Snow Blowers With S/N 891531+
List
Model No.
Specifications & Capacities
Model SBL2566
Model SBL2574
Model SBL2584
66"
74"
84"
Overall Width
71 1/2"
79 1/2"
89 1/2"
Weight with outside skid shoes, case drain
line, couplings, & hydraulic motor
816 lbs
938 lbs
988 lbs
Working Width
Drive and Control System
Hydraulic motors with electric over hydraulic
Hydraulic Requirements:
Low Volume Motor Option
Medium Volume Motor Option
High Volume Motor Option
12 - 19 GPM
20 - 26 GPM
27 - 33 GPM
Hydraulic Pressure Rating
Hitch
2500 - 3500 psi
Skid steer/loader mounting plate
Main Housing Material
10 Gauge
Side Plate Material
3/16"
Chute Opening at the Base
10"
12"
Impeller Housing Depth
8"
10"
Impeller Diameter
Number of Impeller Blades
Auger Diameter
Number of Auger Paddles
Cutting edge
Skid Shoes
24"
4
16"
4
Bolt-on, reversible, and replaceable full-length cutting edge
Bolt-on, adjustable & replaceable
Chute Rotation
220 Degrees (Hydraulically driven sprocket)
Spout Deflector
Hydraulic operation
Spout Deflector Cylinder
Double acting 2" x 4" x1 1/2" rod
35612
3/18/15
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
33
Table of Contents
Section 8: Features & Benefits
Section 8: Features & Benefits
SBL25 Series Snow Blowers With S/N 891531+
Features
Benefits
Large main housing
Ability to handle large drifts.
Large impeller diameter
The ability to move and throw material farther.
Level run indicator 
(Patent-Pending)
Operator can visually verify the Snow Blower is properly leveled before each use. Protects
against tilting the auger into concrete/paved surfaces.
Hydraulically operated
deflector spout
Allows operator to change end of spout up or down from the seat to direct blown snow up
close or far away.
Hydraulically operated chute
rotation with sprocket drive
Allows operator to change direction of snow discharge from the seat. Sprocket drive is built
to last.
Bolt-on reversible and
replaceable cutting edge
Improves service life of Snow Blower by protecting the unit from bottom wear and
absorbing some of the shock when hitting solid objects. The blade can be rotated 180o to
double its life and can be replaced when both edges are worn out.
Greaseable auger end bearing
Less drag on the power train and extends life of unit.
Sprocket driven chute rotator
Allows operator to change chute rotation angle within a 220o discharge pattern.
3/8" Auger Flighting
Stands up to sever use.
Options
Quality hydraulic motor
available in low, medium, or
high volume flow
Provides long life, durable construction. Three flow options allows this Snow Blower to fit
many skid steer/tractors.
Bolted-on outer skid shoes
Supports cutting edge above paved, gravel, and rocky surfaces. 
They are adjustable and replaceable.
Inner skid shoes secured with
a bent pin.
Supports cutting edge above paved, gravel, and rocky surfaces. 
Bent pin makes it easy to change skid shoe height and replace.
34
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 9: Troubleshooting
Section 9: Troubleshooting
Troubleshooting Chart
Problem
Auger and/or impeller
stalls (will not turn)
Cause
Solution
Obstacles are entangled in auger and/or blower
housing.
Impeller jam nut is loose.
Quick couplings did not engage.
Hydraulic system is not engaged.
Hydraulic flow from skid steer or tractor rear
mounted hydraulic reservoir is inadequate.
Skid steer or tractor rear mounted hydraulic
reservoir is low on hydraulic fluid.
Hydraulic hose has a break.
Hydraulic hose has an obstruction.
Hydraulic line is pinched.
Shut Snow Blower down and manually clear
auger and impeller housing.
Tighten impeller jam nut.
Reconnect quick couplings to skid steer.
Engage hydraulic system.
Hydraulic lines have air in them.
Bottom of auger housing
is wearing.
Discharge chute won’t
rotate
Reverse or replace grader blade.
Ice build-up around base of discharge chute.
Wire harness connections are loose.
Solenoid is not operating properly.
Remove ice.
Reconnect wire harness connections.
Have solenoid inspected and repaired.
Refer to hydraulic problems for:
“Auger and/or impeller stalls”
Decrease ground speed.
Decrease motor speed at the flow control
valve.
Remove rotational stop. Rotate chute to
throw snow straight forward. Reattach
rotational stop.
Ground speed is too fast.
Auger motor speed is too fast.
Discharge chute throws
snow at the operator
Rotational stop bolts are on the wrong side of
the rotational stop.
Discharge spout does not
throw snow the preferred
distance
Discharge spout is set at the wrong angle.
Not enough snow to fill the impeller.
Impeller is throwing small
amounts of snow
Auger motor speed is too slow.
Ground speed is too slow.
Hydraulic motor is leaking
Hydraulic motor seals are blown.
oil
Skid shoes are wearing too Loader arms are not set to float.
fast
Snow Blower is not parallel to ground.
Snow Blower makes
intermittent clicking noise
Impeller jam nut is loose.
Auger flighting is bent or broken.
Impeller blades are bent or broken.
Auger is contacting the ground.
Blowing dirty snow or refrozen melted snow.
Snow Blower makes
excessive noises or
vibrates excessively
Snow is left on the ground
3/18/15
Add hydraulic oil to skid steer or tractor rear
mounted hydraulic reservoir.
Replace hydraulic hose.
Remove obstruction or replace hose.
Fix pinched line.
Engage hydraulics to Snow Blower until air is
purged from hydraulic lines.
Grader blade is worn.
Hydraulics problems
Discharge chute is
plugging
Check hydraulic flow at the Snow Blower.
Picking up road gravel and/or crushed rock.
Obstacles are entangled in auger and/or
impeller housing.
End bearing is worn or damaged.
Auger is bent or broken.
Impeller blades are bent or broken.
Skid shoes are set too low.
Extend hydraulic cylinder to shorten throwing
distance. Retract hydraulic cylinder to
lengthen throwing distance.
This is normal when clearing snow fall that is
not very deep.
Increase motor speed at the flow control
valve.
Increase ground speed.
Have the hydraulic motor with leaky seals
repaired.
Set loader arms in float position.
Level Snow Blower.
Tighten impeller jam nut.
Repair or replace damaged auger.
Repair or replace damaged impeller blades.
Adjust Snow Blower to operate level.
(Parallel with the ground.)
Blow only clean fresh snow.
Lower skid shoes to carry grader blade
above road gravel and crushed rock.
Shut Snow Blower down and manually clear
auger and/or impeller housing.
Replace end bearing.
Repair or replace damaged auger.
Repair or replace damaged blades.
Raise skid shoes up.
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
35
Table of Contents
Section 10: Torque Values Chart
Section 10: Torque Values Chart
Torque Values Chart for Common Bolt Sizes
Bolt Head Identification
Bolt Size
(inches)
1
Grade 2
in-tpi
1/4" - 20
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
N·m
7.4
8.5
15
17
27
31
43
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
49
66
75
95
105
2
ft-lb
5.6
6
11
13
20
22
32
36
49
55
70
79
Grade 5
3
N·m
11
13
24
26
42
47
67
75
105
115
150
165
ft-lb
Bolt Head Identification
Grade 8
Bolt Size
(Metric)
8
10
17
19
31
35
49
N·m
16
18
33
37
59
67
95
ft-lb
12
14
25
27
44
49
70
mm x pitch
M 5 X 0.8
M6X1
M 8 X 1.25
M8X1
M10 X 1.5
M10 X 0.75
M12 X 1.75
55
76
85
110
120
105
145
165
210
235
78
105
120
155
170
M12 X 1.5
M12 X 1
M14 X 2
M14 X 1.5
M16 X 2
4
5.8
8.8
10.9
Class 5.8
Class 8.8
Class 10.9
N · m ft-lb
4
3
7
5
17
12
18
13
33
24
39
29
58
42
N · m ft-lb
6
5
11
8
26
19
28
21
52
39
61
45
91
67
N · m ft-lb
9
7
15
11
36
27
39
29
72
53
85
62
125
93
60
90
92
99
145
95
105
145
155
225
130
145
200
l215
315
44
66
68
73
105
70
77
105
115
165
97
105
150
160
230
5/8" - 11
130
97
205
150
285
210
M16 X 1.5
155
115
240
180
335
245
5/8" - 18
150
110
230
170
325
240
M18 X 2.5
195
145
310
230
405
300
3/4" - 10
235
170
360
265
510
375
M18 X 1.5
220
165
350
260
485
355
3/4" - 16
260
190
405
295
570
420
M20 X 2.5
280
205
440
325
610
450
7/8" - 9
225
165
585
430
820
605
M20 X 1.5
310
230
650
480
900
665
7/8" - 14
250
185
640
475
905
670
M24 X 3
480
355
760
560
1050 780
1" - 8
340
250
875
645
1230 910
M24 X 2
525
390
830
610
1150
845
1" - 12
370
275
955
705
1350 995
M30 X 3.5
960
705
1510 1120
2100 1550
1-1/8" - 7
480
355
1080 795
1750 1290
M30 X 2
1060 785
1680 1240 2320 1710
1-1/8" - 12
540
395
1210 890
1960 1440
M36 X 3.5
1730 1270 2650 1950 3660 2700
1-1/4" - 7
680
500
1520 1120
2460 1820
M36 X 2
1880 1380 2960 2190 4100 3220
1 in-tpi = nominal thread diameter in inches-threads per inch
1-1/4" - 12
750
555
1680 1240 2730 2010
2 N· m = newton-meters
1-3/8" - 6
890
655
1990 1470 3230 2380
3 ft-lb= foot pounds
1-3/8" - 12
1010
745
2270 1670 3680 2710
4 mm x pitch = nominal thread diameter in millimeters x thread
1-1/2" - 6
1180
870
2640 1950 4290 3160
pitch
1-1/2" - 12
1330 980
2970 2190 4820 3560
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
36
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
3/18/15
Table of Contents
Section 11: Warranty
Section 11: Warranty
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship beginning on the date of
purchase by the end user according to the following schedule when used as
intended and under normal service and conditions for personal use.
Overall Unit: One year Parts and Labor
Auger, Impeller, Wear Bars & Skid Shoes: Considered wear items
This Warranty is limited to the repair or replacement of any defective part by
Land Pride and the installation by the dealer of any such replacement part, and
does not cover common wear items such as blades, belts, tines, etc. Land Pride
reserves the right to inspect any equipment or parts which are claimed to have
been defective in material or workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.Claims
under this Warranty must be made to the dealer which originally sold the product
and all warranty adjustments must be made through such dealer. Land Pride
reserves the right to make changes in materials or design of the product at any
time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in this
written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days from
the date of purchase by the end user.
IMPORTANT: The Online Warranty Registration should be completed by the dealer at the time of
purchase. This information is necessary to provide you with quality customer service.
Model Number ____________________
3/18/15
Serial Number ____________________
SBL2566, SBL2574, & SBL2584 with S/N 891531+ Snow Blowers 370-478M
37
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com