Fisher & Paykel RS36A72U1 N, RS36A72J1 User guide

Fisher & Paykel RS36A72U1 N, RS36A72J1 User guide
INSTALLATION INSTRUCTIONS
ActiveSmart™ Built-in refrigerator
RS36A72J and RS36A72U models
US CA
www.fisherpaykel.com
843157 A
06.15
FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR CABINETRY
RS36A72J and RS36A72U
models
1 SAFETY AND WARNINGS
2 BEFORE INSTALLATION
3 COMPONENTS LIST
4 PRODUCT AND CAVITY DIMENSIONS
5 CAVITY PREPARATION
6 MAXIMUM DISTANCE OF POWER CORD
7 CUSTOM DOOR PANEL DIMENSIONS
8 ATTACH SIDE TRIM BRACKETS
9 ATTACH ANTI-TIP BRACKET
WOODEN/PLASTER BOARD
WALL INSTALLATION
SOLID WALL
INSTALLATION
SPACER
INSTALLATION
!0 CONNECT TO WATER AND ELECTRICAL SUPPLY
!1 PRODUCT PREPARATION
!2 LEVEL YOUR PRODUCT
!3 ATTACH SIDE TRIMS
!4 ASSEMBLE DOOR PANEL SET
!5 HANGING ICE & WATER DOOR PANEL
!6 HANGING NON-WATER DISPENSING DOOR PANELS
!7 TOP TRIM AND HINGE END CAPS
!8 INSTALL WATER FILTER CARTRIDGE
!9 ATTACH COVERS AND KICKSTRIPS
@0 FINAL CHECKLIST
1
1
2
SAFETY AND WARNINGS
!
Please follow the installation steps below to ensure your appliance is installed and
operates correctly.
WARNING!
Electric Shock Hazard
Read and follow the safety and warnings outlined in this installation
guide before operating this appliance.
Failure to do so can result in death, electric shock, fire or injury
to persons.
Power
●●
●●
●●
!
WARNING!
Cut Hazard
Take care – panel edges are sharp. Failure to use caution could result in
injury or cuts.
BEFORE INSTALLATION
●●
●●
●●
To ensure that the appliance is not accidentally switched off, connect your refrigerator
to its own isolating switch. Do not plug in any other appliance at this isolating switch.
For power requirements, please refer to the information on the serial plate. This is located
at the front right-hand side of the drawer when open.
It is essential that the appliance is properly grounded (earthed).
Connect the appliance to the electrical supply (115VAC, 60 Hz) with the fitted plug and lead.
Follow the National Electrical Code and all local codes and ordinances when installing
this product.
Warning: Ground Fault Circuit Interrupters (GFCI) may trip during normal operation of
your refrigerator and interrupt the power supply. The use of a GFCI is not recommended
with this product.
Location
!
WARNING!
This appliance is top-heavy and must be secured to prevent the
possibility of tipping forward.
●●
●●
●●
To ensure that the appliance is stable under all loading conditions, the
anti-tip bracket and fittings supplied must be installed according to the
following installation instructions by a professional installer.
Your refrigerator should not be located in direct sunlight or next to any heat generating
appliance such as a cooktop, oven or dishwasher.
Your product is fitted with front and rear rollers designed for moving the product
in forwards and backwards direction.
Avoid moving the product in a sides ways direction as this may damage the rollers
or the floor covering/surface.
Plumbing
●●
●●
Your product must be installed by a qualified plumber or Fisher & Paykel Authorized
Service Agents as incorrect plumbing can lead to water leaks.
Fisher & Paykel Appliances does not accept responsibility for damage (including water
damage) caused by faulty installation or plumbing.
Door panel set
●●
●●
●●
●●
The standard appliance does not include a door panel set.
When designing custom door panels, these are only available for non-Water dispensing models.
To complete the integrated appliance for non-Water dispensing models the customer should
supply their own custom door panel set. All the hardware required to mount the door panel
sets to the refrigerator doors is supplied.
Fisher & Paykel door panel sets are available (EZKleen stainless steel door panels, model
numbers: RD3672 and RD3672U), and can be purchased through your Fisher & Paykel
dealer or online at www.fisherpaykel.com (this service is available to selected markets only).
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to
our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
3
3
COMPONENTS LIST
Door panel fittings – Included with standard appliance.
French door
hanging bracket
(2)
Drawer hanging bracket
(1)
Side bracket
(10)
Side strap
(10)
M5 x 10 pan head
Phillips screw (10)
M8 stud
(6)
M8 washer
(6)
M8 nut
(6)
Top cover
(4)
Side cover
(10)
#8 x 16 mush
washer screw (34)
Optional accessories – The standard appliance does not include a door panel set.
Fisher & Paykel door panel sets are available (EZKleen stainless steel door panels). To complete the integrated appliance for non-Water dispensing models the customer should supply their own
custom door panel set.
4
Non-Water dispensing French panels (2)
Drawer panel (1)
Model number: RD3672
Non-Water dispensing French panel (1)
Ice & Water French panel (1)
Drawer panel (1)
Model number: RD3672U
Door handle
(3)
M5 x 25 pan head
socket screw
(12)
M5 x 14 Mush Phillips SS
(34)
3
COMPONENTS LIST
Anti-tip bracket fittings – Included with standard appliance.
Anti-tip bracket (1)
#10 x 40 pan head
Phillips screw (4)
Masonry plug (4)
Product hardware – Included with standard appliance.
Kickstrip filter
(1)
Kickstrip grille
(1)
Power cord clip
(1)
Side trim bracket
(6)
Side trim
(2)
Filter cartridge tool
(1)
External display module (1)
(included with RS36A72U standard appliance)
Ice & Water fittings – Included with standard appliance.
Collet locking key
(1)
Water filter cartridge (1)
Part number: 839041
Water fittings – The standard appliance does not include water fittings. Fisher & Paykel water fittings are available (part number: 841301). These parts need to be purchased separately by the
customer and comply with local regulations.
1/4” (6 mm)
Compression nut
(1)
1/4” (6 mm)
Compression sleeve
(1)
1/4” (6 mm)
Tube insert
(1)
¼” (6 mm) PEX tube
(1)
5
F F
4
F F
F F
PRODUCT AND CAVITY DIMENSIONS
J J
B
G G
C
B
F
A A
D D
A A
3 1/2”
(89 mm)
C
5/32”
(4 mm)
F
Framed: Finish return
Note: shows adjoining cabinetry
not sharing 5/32” (4 mm) door gap
E E
I I
PLAN VIEW
H H
F
F
PRODUCT DIMENSIONS
PROFILE VIEW
A
D
D Overall height of product*
E Overall width of product
CAVITY DIMENSIONS
inches (mm)
A Overall height of cavity
72” (1829)
B Overall width of cavity
36” (914)
(when adjoining cabinetry cannot share 5/32” (4 mm) door gap)
C Overall depth of cavity*
25” (635)
J
inches (mm)
71 27/32” (1825)
35 1/32” (890)
F Minimum cabinetry gap clearance from edge of custom panels**
5/32” (4)
G Overall depth of product (excluding front door panels)
23 3/4” (603)
H Depth of toe kick (measured from front of door panels***)
I Height of grille/toe kick*
2” (51)
4” (102)
D
A
J Depth of product front panels (excludes handles)***
5/8” – 3/4” (16 – 19)
Total front panel width with required gaps at sides = 36” (914 mm). (Refer to custom door panel dimensions section –
panel width + 2 x F cabinetry gaps).
* Includes mounted feet.
* Assumes a door panel thickness of 3/4” (19 mm).
***Door panels to be manufactured and fitted by cabinetmaker, min. 5/8” (16 mm) - max. 3/4” (19 mm) thickness.
RS36A72J model shown only.
When designing custom door panels, with non-Water dispensing models.
J
F
C C
B B
FRONT VIEW
F
Flush with front
of cabinetry
** Refer to custom door panel dimensions section.
E
H
I
B
6
E
I
H
4
PRODUCT AND CAVITY DIMENSIONS
C
B
D
A
115° DOOR OPENING
(FULL ROTATION)
115° DOOR OPENING
[FULL ROTATION]
Wall
B
A
90° DOOR OPENING
Wall
90° DOOR OPENING
DOOR CLEARANCE DIMENSIONS
inches (mm)
A Depth of door (widest opening) measured from front of cabinetry
17 5/16” (440)
B Depth of drawer (open) measured from front of cabinetry*
15 3/4” (400)
C Minimum door clearance** to adjacent wall* (115° – full internal access)*
11 13/16” (300)
D Minimum door clearance** to adjacent wall* (90° – reduced internal access)*
3 13/16” (100)
* Does not include the custom door panels or handles to be manufactured and fitted by cabinetmaker.
** Measured from front cabinetry edge.
7
F F
4
F F
PRODUCT AND CAVITY DIMENSIONS – WITH RD3672 DOOR PANEL SET
B
L L
F F
G G
C
B
K K
F
A A
D D
3 1/2”
(89 mm)
A A
C
5/32”
(4 mm)
Framed: Finish return
Note: shows adjoining cabinetry
not sharing 5/32” (4 mm) door gap
J J
E E
I I
F
F
F
C C
PRODUCT DIMENSIONS
D
inches (mm)
Overall height of product*
71 27/32” (1825)
35 21/32” (906)
A
D
F Minimum cabinetry gap clearance from edge of product
5/32” (4)
G Overall depth of product (excluding front door panels)
CAVITY DIMENSIONS
inches (mm)
A Overall height of cavity
72” (1829)
B Overall width of cavity
36” (914)
(when adjoining cabinetry cannot share 5/32” (4 mm) door gap)
C Overall depth of cavity
25” (635)
Total front panel width with required gaps at sides = 36” (914 mm) ( E product width + 2 x
Height of front panels with required gap above =
D product height + F cabinetry gap.
F cabinetry gaps).
23 3/4” (603)
H Depth of toe kick (measured from front of door panels)
2” (51)
K
I Height of grille/toe kick*
J
J Height of bottom drawer panel
K Height of top door panels
4” (102)
23 15/32” (596)
44 7/32” (1123)
A
D
L Depth of product front panels (excludes handles)**
* Includes mounted feet.
L
K F
E Overall width of product
PROFILE VIEW
L
PLAN VIEW
H H
B B
FRONT VIEW
F
Flush with front
of cabinetry
3/4” (19)
E
I
**Optional EZKleen stainless steel front panels - Model no. RD3672 (non-Water dispensing model) and model no.
RD3672U (Ice & Water model).
B
H
J
RS36A72J model shown with RD3672 door panel set.
8
E
I
H
4
PRODUCT AND CAVITY DIMENSIONS – WITH RD3672/RD3672U DOOR PANEL SET
D
E
B C
A
115° DOOR OPENING
(FULL ROTATION)
115° DOOR OPENING
[FULL ROTATION]
Wall
B C
A
90° DOOR OPENING
Wall
90° DOOR OPENING
DOOR CLEARANCE DIMENSIONS
inches (mm)
A Depth of door (widest opening) measured from front of door
17 5/16” (440)
B Depth of drawer (open) measured from front of drawer, including handle
15 3/4” (400)
C Depth of drawer (open) measured from front of drawer, excluding handle
14 3/16” (360)
D Minimum door clearance to adjacent wall* (115° – full internal access)
11 13/16” (300)
E Minimum door clearance to adjacent wall* (90° – reduced internal access)
3 13/16” (100)
* Measured from front cabinetry edge.
9
5
A
CAVITY PREPARATION
!
Recommended area above
cavity for connections
C
31 1/2” (800 mm)
2 15/16”
(75 mm)
5 29/32”
(150 mm)
4 11/32”
(110 mm)
4 11/32”
(110 mm)
Floor
B
5 3/32”
(129 mm)
5 29/32”
(150 mm)
Alternative electrical connection location
REAR VIEW OF CAVITY
CAVITY DIMENSIONS
A
Electrical
Plumbing
inches (mm)
A Overall height of cavity
72” (1829)
B Overall width of cavity
36” (914)
(when adjoining cabinetry cannot share 5/32” (4 mm) door gap)
B
C Overall depth of cavity
Electrical
Plumbing
!
25” (635)
RS36A72J
RS36A72U
Supply
115VAC, 60 Hz
115VAC, 60 Hz
Service
10 amp circuit
10 amp circuit
Supply
–
1/4” (6 mm) PEX hose or Copper tubing*
Pressure
–
Minimum 22 psi (150 kPa)
Maximum 120 psi (827 kPa) @ 20°C
ELECTRICAL SPECIFICATIONS
C
B
PLUMBING SPECIFICATIONS
F
3 1/2”
(89 mm)
5/32”
(4 mm)
10
Frameless: Finish return,
sides and top
ote: recommended that the electrical and water connection be located above the fridge cavity. Optional to locate
N
in an adjacent cabinet to either side of the fridge.
Do not locate water or electricity in this area, keep clear of connections.
F
F
L !!
G
CAUTION: central area can only fit electrical plug if it is placed within a recessed cavity.
* Water fittings kit – The standard appliance does not include water fittings. Standard Fisher & Paykel water fittings
kit are available (part number: 841301). These parts need to be purchased separately by the customer and comply
with local regulations.
6
MAXIMUM DISTANCE OF POWER CORD
Power cord (excl.plug) – 31 1/2” (800 mm)
LEFT HAND SIDE
Power cord (excl.plug) – 80 23/32” (2050 mm)
RIGHT HAND SIDE
Power cord (excl.plug) – 80 23/32” (2050 mm)
11
7
CUSTOM DOOR PANEL DIMENSIONS
B
C
A
A
B
g
C
A
A
E
g
H
D
g
D
F
E
g
H
PROFILE VIEW
ISO VIEW
D
DIMENSIONS
A Height of top door panel PROFILE
RS36A72J
VIEW
B Width of top door panel
F
D
C Gap between top door panels
D Height of bottom drawer panel
ISO VIEW
ISO VIEW
12
17 3/4” (451)
5/32” (4)
23 15/32” (596)
E Height from bottom of product to top of bottom drawer panel
27 15/32” (698)
F Width of bottom drawer panel
35 21/32” (906)
PROFILE
VIEW
door panels
and bottom drawer panel
G Gap between top
H Depth of custom panels
RS36A72J model shown only.
When designing custom door panels, with non-Water dispensing models.
inches (mm)
44 7/32” (1123)
5/32” (4)
min. 5/8 - max. 3/4” (16-19)
Maximum weight of an individual top door panel
22 pounds (10 kg)
Maximum weight of bottom drawer panel
21 pounds (9.5 kg)
Custom door panels and handles to be manufactured and fitted by cabinetmaker.
7
CUSTOM DOOR PANEL DIMENSIONS
The drawings below apply to non-Water dispensing models only. Dimensions are shown in Imperial (inches) and apply for the preparation and installation of custom door panels.
For Dwg and Dxf files of the below panel preparation download the folder on http://thekitchentools.fisherpaykel.com
15 7/16
2 5/32
Ø 3/32 REF
12x Pilot holes recommended for bracket attachment.
(Do not penetrate front surface).
Ensure handle is mounted
2 9/16” from inner edge of panel
to the center – this will avoid
interference with brackets.
38 5/8
24 15/16
15 5/32
40
26 29/32
Ø 3/32 REF
5 1/32
4 31/32
All measurements to be made
from inner bottom corner.
For the second panel mirror
and repeat dimensions using
inner bottom corner as the
reference point.
6 15/16
3 7/16
10x Pilot holes recommended for
bracket attachment.
(Do not penetrate front surface).
1 5/32
All measurements to be made
from top and centerline.
1 3/8
21 11/32
19 3/8
16 5/16
16 3/8
TOP PANEL – REAR VIEW
Ensure handle screw heads
are counter sunk into back of
panel to avoid interfering with
hanging bracket.
BOTTOM PANEL – REAR VIEW
13
8
ATTACH SIDE TRIM BRACKETS
A
IMPORTANT!
Before installing your appliance, ensure the dimensions
of the finished enclosure are correct for your appliance
following the ‘Product and cavity dimensions’ section.
3/4” (19 mm)
~ 4” (100 mm)
~ 35” (900 mm)
~ 4” (100 mm)
3/4” (19 mm)
Discard
1
Break off the datum lip to each side trim bracket
and discard.
Repeat for all side trim brackets x6.
2
On one side of the finished enclosure, starting from the
top, measure ¾’’ (19 mm) from the front cabinetry edge
towards the back with the side trim bracket (refer to A).
Mark side trim bracket screw locations for the top,
center and bottom of the finished enclosure.
Repeat on the right side of the finished enclosure.
14
3
Fix side trim brackets to the side of one enclosure
with screws x2 (#8 x 16 pan head Phillips screw).
Ensure screws hold tight.
Repeat for remaining side trim brackets.
9
ATTACH ANTI-TIP BRACKET
IMPORTANT!
Safety requires refrigerators be stable when doors and/or drawer, are open. An anti-tip bracket and fittings supplied must be fitted to the wall of the finished enclosure to withstand
a 220.5 pound (100 kg) load. This will prevent the possibility of the appliance tipping forward, when doors and/or drawer, are open.
●●
●●
●●
●●
When fastening with masonry plugs and/or screws:
Ensure the screws avoid electrical, gas and water conduits.
Ensure the surface the bracket is fastened to withstand a 220.5 pound (100 kg) load.
Ensure light-weight masonry material such as cinder block and new concrete (no curing time) are not used in installation.
Do not use metallic materials that may corrode, stain and/or damage the enclosure.
WOODEN/PLASTER BOARD
WALL INSTALLATION
1
Project the end of the above finished enclosure to the
center of the back wall and subtract 1 ¼” (31 mm). This
will locate the contact surface between the bracket and
the appliance (refer to A).
Ensure a structural beam/wall stud closest to the center
of the wall enclosure is located.
SOLID WALL INSTALLATION
1
Project the end of the above finished enclosure to the
center of the back wall and subtract 1 ¼” (31 mm). This
will locate the contact surface between the bracket and
the appliance (refer to A).
SPACER INSTALLATION
If a minimum 2 3/8” (60 mm) overlap cannot be achieved
we recommend fastening a solid spacer (wooden beam etc)
behind the bracket.
1
Ensure the length of the spacer corresponds to the
enclosure’s width. Always secure the spacer to existing
studs on the enclosure wall (refer to C).
1 1/4” (31 mm)
1 1/4” (31 mm)
2 3/8” min.
(60 mm)
overlap
2 3/8” min.
(60 mm)
overlap
A
1 1/4” (31 mm)
A
2 3/8” min.
(60 mm)
overlap
Bracket
PROFILE VIEW
Bracket
PROFILE VIEW
2Fix bracket to the wall with screws x4 (#10 x 40 pan head
Phillips screw). Ensure screws hold tight and the bracket
overlaps the appliance when it is positioned (2 3/8” min.
(60 mm)) for a secure hold.
Spacer
C
Bracket
PROFILE VIEW
2
Mark screw locations to drill Ø ¼” x 1 ⅜” (Ø6.0 mm x 35 mm)
deep holes. Hammer masonry plugs into the wall until flush
x4. Fix bracket to the wall with screws x4 (#10 x 40 pan
head Phillips screws). Ensure screws hold tight.
2
Fix bracket to the spacer with screws x4 (#10 x 40 pan
head Phillips screws). Ensure screws hold tight and the
bracket overlaps the appliance when it is positioned
(2 3/8” min. (60 mm)) for a secure hold.
15
!0
CONNECT TO WATER AND ELECTRICAL SUPPLY
IMPORTANT!
●●
●●
●●
●●
●●
●●
●●
●●
●●
The water connection to your Ice & Water refrigerator must be installed by a qualified
plumber or a Fisher & Paykel Authorized Service Agent.
The water connection instructions below are intended only for the professional installer.
DO NOT use water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
WARNING – connect to potable water supply only.
DO NOT install on line pressure above 120 psi (827 kPa) or below 22 psi (150 kPa).
DO NOT use on hot water supply (100°F [38°C max.]).
AVOID contamination of pipes during installation.
New water fittings (hose-sets) are to be used on the appliance. Old water fittings
(hose-sets) should not be reused.
The standard appliance does not include water fittings. Fisher & Paykel water fittings
are available (part number: 841301). These parts need to be purchased separately by
the customer and comply with local regulations.
3
At the front of the product, dislodge the PLV. Grasp the PLV from the clips by pulling
it towards you (refer to A).
A
Front view
The assembly of Fisher & Paykel water fittings are outlined below, other water fittings
purchased separately also follow the installation steps below:
1
Ensure the refrigerator is NOT plugged into a power supply. Locate isolating faucet
2
for water connection – cold water supply only. Tee and faucet fitting not supplied.
Ensure there is enough tubing for the water connection and to pull the appliance
out for service, if required.
Uncoil the ¼” (6 mm) water tubing and thread one end through the opening in the rear
cover until it exits the front.
4 Firmly insert water tubing into the PLV. The tube should push in at least 5/8” (16 mm)
before reaching the stop. Once inserted, pull gently on tubing to ensure it is locked
in (refer to B).
Secure the connection by attaching the locking key in between the PLV and water
tubing (refer to C). Mount the PLV back into the clip.
B
Rear view
C
16
!0
CONNECT TO WATER AND ELECTRICAL SUPPLY
5
Position the appliance 1.5 – 2 ft. (450 – 600 mm) in front of the finished enclosure
(refer to D). This will allow access behind the appliance for water and power
connections.
At the back of the appliance, cut the water tube to a suitable length for connecting
to the water outlet. Ensure there is enough tubing to pull the appliance out for
service, if required.
6
Assemble the following water fittings onto the other end of the water tube.
Insert tube
Compression
sleeve
Compression
nut
Water tube
Final water tube connection
7
Fasten the faucet connection to the cold water supply. Take care
not to over-tighten the faucet connection. Turn isolating faucet
on and check that all connections are dry and free of drips.
8
Connecting power
At the back of your appliance adhere the power cord clip.
Connect the appliance to the electrical supply (115 VAC, 60 Hz
with the fitted plug and lead, and turn on. Ensure the appliance
is connected to its own isolating switch.
1
50 .5 –
– 6 2 ft
00 .
mm
(4
Ensure excess power cord length is secured onto the clip (refer to E).
When pushing the appliance into position, take care not to roll over
or damage the power cord and/or water tubing.
D
)
E
IMPORTANT!
●●
●●
Ensure water tubing is routed away from any sharp objects, sharp corners (beware of kinking the tube as this will stop water flow), and not in a location where it can be kinked or squashed.
Ensure a firm contact is observed as the appliance engages the anti-tip bracket, 2 ⅜” min. (60 mm) overlap.
17
C
P
!1
1
Carefully open the
refrigerator French doors
and remove the left hinge
end cap.
Hold onto the corner of
the end cap, firmly push
to the right to disengage
securing hook and pull
down (Refer to A).
2
A
PRODUCT PREPARATION
4
Pull cap gently towards
the left hinge to remove
(Refer to B).
Secure M8 studs into
the refrigerator doors,
ensure the open end
faces the top.
Repeat on all
refrigerator doors.
B
Reserve end hinge cap
for later installation.
3
Remove the right hinge
end cap. Press on the
center of the cap and
push towards the right
hinge to remove.
Reserve end hinge cap
for later installation.
18
5
Secure mid-way,
M5 x 10 pan head
Phillips screw into
the refrigerator doors.
Repeat on all
refrigerator doors.
!2
●●
●●
●●
1
!3
LEVEL YOUR PRODUCT
It is important that all four corners of the product is supported firmly onto the floor to
eliminate any movement.
Installing the appliance on a soft, uneven, or not level floor may result in twisting of the
product and poor door sealing.
Raise the product using an 7/16” (11 mm) hex socket or 3/16” (4 mm) hex Allen key. One
turn of height adjusting nuts is equivalent to 1/16” (1 mm) height travel.
Note: maximum travel 13/16” (20 mm).
1
ATTACH SIDE TRIMS
Left side trim
Ensure the shorter side trim lip is facing
the top of the product (refer to A).
Insert the trim into the gap between
the left side of the appliance and
enclosure with the lip facing out.
Level the front of the product until it is flush with adjacent walls. Turn clockwise to raise
roller or counter-clockwise to lower roller.
A
Repeat on opposite side.
B
2
Raise the rear of the product until the refrigerator doors are flush with the front face
of adjacent walls. Turn clockwise to raise roller or counter-clockwise to lower roller.
Repeat on opposite side.
Gently push the front of the product to check the stability, and ensure side gaps are
even with enclosure.
2
Right side trim
Ensure the shorter side trim lip is facing
the top of the product (refer to B).
Insert the trim into the gap between
the right side of the appliance and
enclosure with the lip facing out.
19
!4
ASSEMBLE DOOR PANEL SET
The assembly of Fisher & Paykel door panel sets (EZKleen stainless steel door panels) and custom door panel sets are outlined below.
For Fisher & Paykel door panel sets, only remove the protective film for handle installation. This will protect the finish of the door panels until installation is complete.
French door panels
1
Drawer door panel
Mounting handle (Refer to A)
For Fisher & Paykel door panel sets, remove
the plastic plugs from the handle holes x4.
Align the handle to the holes and secure
with screw handle x4 (M5 x 25 pan head
socket screws).
4
B
For custom panels, ensure handle is secured
2 9/16” (65 mm) from the inner edge of the panel
to the center – this will avoid interference with
bracket installation.
Mounting handle (Refer to D)
For Fisher & Paykel door panel sets,
remove the plastic plugs from the handle
holes x4. Align the handle to the holes and
secure with screw handle x4 (M5 x 25 pan
head socket screws).
D
For custom panels, ensure handle screw
heads are counter sunk into the back
of the panel to avoid interference with
hanging bracket.
A
2
Hanging bracket (Refer to B)
For Fisher & Paykel door panel sets, align the
bracket to the holes and secure with screws x4
(M5 x 14 Mush Phillips SS).
5
For custom panels, secure bracket with screws x4
(#8 x 16 Mush washer screws).
3
20
Side brackets and straps (Refer to F)
For Fisher & Paykel door panel sets,
align bracket and strap to the holes on
the side of the panel and secure with
screws x2 (M5 x 14 Mush Phillips SS).
For custom panels, secure bracket with
screws x2 (#8 x 16 Mush washer screws).
For custom panels,
secure bracket with
screws x2 (#8 x 16
Mush washer screws).
Repeat this process
for all brackets and
straps, and remaining
French door panel.
E
For custom panels, secure bracket with
screws x6 (#8 x 16 Mush washer screws).
6
Side brackets and straps (Refer to C)
For Fisher & Paykel door panel sets,
align bracket and strap to the holes
on the side of the panel and secure
with screws x2 (M5 x 14 Mush
Phillips SS).
Hanging bracket (Refer to E)
For Fisher & Paykel door panel sets, align
the bracket to the holes and secure with
screws x6 (M5 x 14 Mush Phillips SS).
Repeat this process for all brackets
and straps.
C
F
!5
1
HANGING ICE & WATER DOOR PANEL
5
Remove the external display
module from inside the product.
Thread the display harness
through the door panel cavity.
Ensure the grommet is engaged.
2
Connect the display
harness onto the
refrigerator door by
firmly inserting until
you feel it clip securely
(refer to B).
B
On the external display,
enable the dispenser lock,
this will help prevent any
water from dispensing during
water connection. To lock, press
the
button for 4 seconds.
The LED above the button will
illuminate.
Angle top display tabs into the
door panel. Ensure the harness
is free of pinching. Firmly push
against bottom display tabs
and insert into the door panel
until you feel it clip securely.
Ensure the display is flush with
the door panel.
A
6
3
Remove water tube from holder
on the refrigerator door.
4
Hang door panel onto M8 studs.
Ensure the panel is free to pivot
for water connections (refer to A).
Firmly push the water tube
into the spigot behind the
door panel until the marked
line is not visible. Ensure the
water tube is routed away
from any sharp objects, sharp
corners, and not in a location
where it can be kinked or
squashed when the door
panel is secured, (as this will
stop water flow).
To secure door panel, follow
the instructions in the next
section: ‘Hanging non-Water
dispensing door panels’.
21
!6
1
Hang all door panels onto M8 studs
and align the side bracket forks
onto the refrigerator door.
HANGING NON-WATER DISPENSING DOOR PANELS
3
Once satisfied with all door panels,
secure M8 studs with M8 washer
and M8 nut. The top of the stud
must remain below the top face of
the door panel.
4
Secure side bracket forks by
tightening side screws.
Ensure the forks are positioned
around the body of the side screw
(M5 x 10 pan head Phillips screw).
2
22
All door panels have full axis
adjustment to ensure they are
flush with adjacent walls, or until
satisfactory. To adjust the height of
each panel turn clockwise to raise stud
or counter-clockwise to lower stud.
Repeat this process for all door
panels. Ensure all door panels are
flush with adjacent walls, adjust
accordingly or until satisfactory.
150
C
P
TOP
TRIM AND HINGE END
CAPS
!7
!8
INSTALL WATER FILTER CARTRIDGE
IMPORTANT!
150
The water filter head must be firmly pushed into the product and secured, incorrect
installation can lead to water leaks.
0
C
Secure the top trim to the
L
ceiling of the enclosure
with screw x1 (#8 x 16 mush
washer screw).
Repeat this process on the
opposite side.
2
18
1
O
Replace the left hinge end
cap. Align hinge cap to the
product, press and firmly
slide the cap to the right
(refer to A).
1
Remove the red protective cap on the
spigot head and align the filter cartridge
tool over the filter handle.
2
Pull the freezer drawer out slightly and
insert the filter cartridge and tool into
the bottom left of the product. Firmly
push the cartridge in until the filter head
cannot be pushed any further (refer to A).
3
Turn 90° clockwise to tighten. Remove filter
cartridge tool and close freezer drawer.
P
A
A
Hold onto the corner of
the end cap, firmly push up
and to the left to engage
securing hook. Ensure cap
is flush with the product.
B
3
Replace right hinge end
cap. Align hinge cap to
product, press and firmly
slide the cap to the left
(refer to B). Ensure cap is
flush with the product.
Filter cartridge in the locked position
23
!9
1
To stabilize the product, lower the
front feet. Turn clockwise to lower feet.
ATTACH COVERS AND KICKSTRIPS
4
For Fisher & Paykel door panel sets,
remove any remaining protective film
from all door panels.
5
Open the refrigerator French doors to
conceal the outer top studs using top covers.
Firmly push top cover over top door studs.
Repeat on the opposite side.
2
3
24
Kickstrip filter
Remove filter from inside the product.
Fit the filter onto the rails and push to
the rear until it clips securely.
Kickstrip grille
Align clips on the back of the grille with
openings on front face of plinths. Push grille
firmly onto product until it clips securely.
Repeat this process for the freezer drawer.
6
Open the refrigerator French doors to
conceal the side screws using side covers.
Firmly push side cover over side screws.
Repeat this process for the freezer drawer.
@0
FINAL CHECKLIST
Ice & Water models only
TO BE COMPLETED BY THE INSTALLER
All models
Check all parts are installed.
Ensure the water filtration system has been flushed.
●●
Ensure the product is level.
Ensure the product is securely fastened to the cabinetry with the supplied
anti-tip bracket and fittings.
Ensure the doors/drawer can open and close freely with no resistance from
surrounding cabinetry.
●●
●●
To flush the water filtration system
When using your water dispenser for the first time, run the dispenser pad until water
dispenses, this will displace trapped air in the water tank and filter system. This will take
at least 2 minutes. Once water has dispensed, rest the dispenser pad for 2 minutes.
Dispense and discard 4 qt (4 L) of water, then rest the dispenser pad for a further
2 minutes, repeat process.
Failure to do this will result in excessive dripping from your water dispenser.
IMPORTANT!
DO NOT continuously dispense water for longer than 2 minutes at a time.
Ensure all internal and external packaging is removed from the appliance
before use.
Ensure change filter icon is enabled. This will remind you when the filter next
needs replacing. Press and hold
,
and
for 4 seconds on the internal
control panel.
Ensure a manual ice maker cycle has been forced. Press and hold
,
and
for 4 seconds on the internal control panel, then close the refrigerator
compartment door. The ice tray will flip twice. Empty the water from the bin,
then dry and replace.
Ensure ice maker is turned on. Press
button once on the internal control
panel. This light above the button will illuminate indicating ice maker is on.
Please discard the first 24 hours of ice harvest.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address Installer’s Name
Installer’s Signature
Installation Company
Installation Date
25
www.fisherpaykel.com
Copyright © Fisher & Paykel 2015. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
US CA
843157 A
06.15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement