Single Pole (One location) or 3-Way (Multi-location)

Electronic Low Voltage Dimmer

Cat. No. VREØ6-1L, 600W (Lighted)

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

WARNINGS AND CAUTIONS

:

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these instructions, consult a qualified electrician.

• To avoid overheating and possible damage to this device and other equipment, do not install to control a receptacle, fluorescent lighting, a motor- or a transformer-operated appliance.

• Use with electronic low voltage transformers only. Do Not use to control a magnetic low voltage transformer. Use a Leviton magnetic low voltage dimmer to control magnetic low voltage transformers.

• This dimmer provides protection from overheating. An excessive load applied to the dimmer will cause the dimmer to overheat. The excess load must be removed to resume proper operation.

• Vizia RF +™ dimmers are not compatible with standard 3-way or 4-way switches. They must be used with compatible Vizia +™ remotes or Vizia RF +™ controllers for multi-location dimming.

• Use only one (1) Vizia RF +™ dimmer in a multi-location circuit with up to 9 coordinating remotes (without LEDs) or up to 4 matching remotes (with LEDs). The remote(s) will turn the light on at the brightness level selected at the dimmer.

• Lighting fixture and dimmer must be grounded.

WARNINGS AND CAUTIONS

:

• This dimmer must be installed in a wall box with a neutral connection.

• Consult fixture manufacturer to determine if their solid state transformers can be dimmed.

• Total minimum load must exceed 40W.

• Dimmer may feel warm to the touch during normal operation.

• Recommended minimum wall box depth is 2-1/2".

• Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft (90 m).

• Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.

• Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

INTRODUCTION

Leviton’s Vizia RF + TM components are designed to communicate with each other via Radio Frequency (RF) to provide remote control of your lighting. Using RF technology allows Leviton to provide the greatest signal integrity possible. Each module in Leviton’s Vizia

RF + TM component line is a Z-Wave ® enabled device. In a Z-Wave ® network, each device is designed to act as a router. These routers will re-transmit the RF signal from one device to another until the intended device is reached. This ensures that the signal is received by its intended device by routing the signal around obstacles and radio dead spots. The Electronic Low Voltage Dimmer is compatible with any Z-Wave ® enabled network, regardless of the manufacturer and can also be used with other devices displaying the Z-Wave ® logo.

CAUTION:

Remember to exercise good common sense when using the Timer features of your remote, especially when scheduling unattended devices. There can be some unexpected consequences if not used with care. For example, an empty coffee pot can be remotely turned on. If that should happen, your coffee pot could be damaged from overheating. If an electric heater is turned on by remote control while clothing is draped over it, a fire could result.

FEATURES

• This is a Z-Wave ® controller

• Controls dimming of load

• ON/OFF LED and Brightness LED

• Two way communication

• RF reliability

• Ease of installation - No new wiring

• Compatible with other Z-Wave ® enabled devices

Tools needed to install your Dimmer

Slotted/Phillips Screwdriver

Pliers

Cutters

Electrical Tape

Pencil

Ruler

Changing the color of your Dimmer:

Your device may include color options. To change color of the face, proceed as follows:

Push in side at tab to release

Line up tabs and press in sides one at a time to attach

1

3

4

Installing Dimmer by itself or with other devices

If installing Dimmer in a single device application, proceed with the

INSTALLING YOUR DIMMER section. If installing Dimmer in a multidevice application, proceed as follows:

MULTI-DEVICE APPLICATION:

In multi-dimmer installations, the reduction of the dimmer’s capacity is required. Refer to the chart for maximum load per dimmer.

MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE

Cat. No.

Single Two Devices More than 2 Devices

VREØ6 600W 500W 400W

INSTALLING YOUR DIMMER

Step 1

Remove all inner side sections

Do not remove outer side sections

WARNING:

TO AVOID FIRE, ShOCk, OR DEATh;

TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!

/&&

/&&

/&&

/&&

/&&

/&&

/.

/.

/.

/.

/.

/.

/&&

/&&

/&&

/&&

/&&

/&&

/.

/.

/.

/.

/.

/.

Step 2

2

Identifying your wiring application

(most common):

NOTE: If the wiring in the wall box does not resemble any of these configurations, consult a qualified electrician.

Single-Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

1

3

4

5

2

3-Way

1. Line or Load

(See important

instruction

below)

2. Neutral

3. Ground

4. First Traveler

– note color

5. Second Traveler

– note color

IMPORTANT: For 3-Way applications, note that one of the screw terminals from the old switch being removed will usually be a different color (Black) or labeled Common. Tag that wire with electrical tape and identify as the common (Line or Load) in both the dimmer wall box and remote wall box.

Step 3

Preparing and connecting wires:

cut

(if necessary)

5/8”

(1.6 cm)

Strip Gage

(measure bare wire here or use gage on back of the dimmer)

Step 4b

Bk

3-Way Wiring with Coordinating Remote

(no LEDs) Application:

Coordinating Remote

Wh

2

Dimmer

Yellow/Red

White

5

2

Black

1

• Make sure that the ends of the wires from the wall box are straight (cut if necessary).

• Remove insulation from each wire in the wall box as shown.

• For Single Pole Application, go to Step 4a.

• For 3-Way Coordinating Remote (no LEDs) Application, go to Step 4b.

• For 3-Way Matching Remote (with LEDs) Application, go to Step 4c.

For non-standard wiring applications, refer to Wire Nut and Conductor Size Chart

WIRE NUT / # OF CONDUCTOR COMBINATION ChART

1- #12 w/ 1 to 3 #14, #16 or #18

2- #12 w/ 1 or 2 #16 or #18

1- #14 w/ 1 to 4 #16 or #18

2- #14 w/ 1 to 3 #16 or #18

YL/RD

RD

Electronic

Low Voltage

Transformer

Bla c k

Prima r y

Side

White

5

3

Coo r dinating Remote (no LEDs )

WH

RD

(u n used )

1

4

BK

(u n used )

Green

G r oun d

YL/RD

White

Green

G r oun d

Red

Red

Green

Dimmer

4

3

Bla c k

Hot (Bla c k )

Y ell o w/Re d Line

120VAC

60Hz

Step 4a

Single-Pole Wiring Application:

Neutral (White)

Yellow/Red

White

Insulating Label:

This wire is used in

3-way installations only.

For single pole installations, do not remove this insulating label.

Black

Red

Green

1

3

4

2

Dimmer

White Black hot (Black)

Electronic

Low Voltage

Transformer

Primary

Side

Black

White

Green

Ground

Red

Yellow/Red

Insulating

Label

Line

120VAC, 60hz

Neutral (White)

WIRING DIMMER:

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green dimmer lead.

• Line Hot wall box wire to Black dimmer lead.

• Load wall box wire to Red dimmer lead.

• Line Neutral wall box wire to White dimmer lead.

• Yellow/Red dimmer lead should have Red insulation label affixed.

NOTE: If insulating label is not affixed to Yellow/Red dimmer lead, use electrical tape to cover.

• Proceed to Step 5.

WIRING DIMMER:

Connect wires per WIRING DIAGRAM as follows:

NOTE: The dimmer must be installed in a wall box that has a Line Hot connection.

NOTE: Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft (90 m).

• Green or bare copper wire in wall box to Green dimmer lead.

• Line Hot (common) wall box wire identified (tagged) when removing old switch to Black dimmer lead.

• First Traveler wall box wire to Red dimmer lead (note wire color).

• Remove Red insulating label from Yellow/Red dimmer lead.

• Second Traveler wall box wire to Yellow/Red dimmer lead (note wire

color). This traveler from the dimmer must go to the terminal screw on the remote marked "YL/RD".

• Line Neutral wall box wire to White dimmer lead.

WIRING COORDINATING REMOTE:

Connect wires per WIRING DIAGRAM as follows:

NOTE: "BK" and "RD" terminals on coordinating remote are unused.

Tighten both screws.

NOTE: Maximum wire length from dimmer to last remote is

300 ft (90 m).

• Green or bare copper wire in wall box to Green terminal screw.

• Load wall box wire identified (tagged) when removing old switch to First

Traveler (note color as above).

• Second Traveler wall box wire (note color as above) to terminal screw marked "YL/RD". This traveler from the remote must go to the Yellow/Red dimmer lead.

• Remove White insulating label from terminal screw marked "WH".

• Line Neutral wall box wire to terminal screw marked "WH".

• Proceed to Step 5.

Step 4c

3-Way Wiring with Matching Remote

(w/LEDs) Application:

Matching Remote

Bk

Wh

YL/RD

RD

2

1

4

3

5

Additional

Neutral Wire

Dimmer

Yellow/Red

White

5

Black

4

Red 1

Green

Mat c hing Remote (with LEDs )

Hot (Black)

Line

120VAC

60Hz

WH

BK

Green

G r oun d

YL/RD

White

Green

G r oun d

Red

Dimmer

Bla c k

Yellow/

Red

Neutral (White)

DI-000-VRE06-02A-X2

3

2

Bla c k

Electronic

Low Voltage

Transformer

Prima r y

Side

White

NOTE: The dimmer must be installed in a wall box that has a Load connection. The matching remote must be installed in a wall box with a Line Hot connection and a Neutral connection. A Neutral wire to the matching remote needs to be added as shown.

If you are unsure about any part of these instructions, consult a qualified electrician.

NOTE: Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft (90 m).

WIRING MATChING REMOTE (wall box with line hot connection):

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green terminal screw.

• Line Hot (common) wall box wire identified (tagged) when removing old switch and First Traveler to Remote terminal marked BK.

• Second Traveler wall box wire from dimmer to remote terminal screw marked "YL/RD" (note wire color). This traveler from the remote must go to Yellow/Red dimmer lead.

• Line Neutral wall box to remote terminal screw marked "WH".

WIRING DIMMER (wall box with load connection):

Connect wires per WIRING DIAGRAM as follows:

• Green or bare copper wire in wall box to Green dimmer lead.

• Load wall box wire identified (tagged) when removing old switch to

Red dimmer lead.

• First Traveler Line Hot to Black dimmer lead.

• Remove Red insulating label from Yellow/Red dimmer lead.

• Second Traveler wall box wire (note color as above) to

Yellow/Red dimmer lead. This traveler from the dimmer must go to the terminal screw on the remote marked "YL/RD".

• Line neutral wall box wire to White dimmer lead.

• Proceed to Step 5.

Step 5

Testing your Dimmer prior to mounting in

wall box:

• Position all wires to provide room in outlet wall box for device.

• Ensure that the word “TOP” is facing up on device strap.

• Partially screw in mounting screws in wall box mounting holes.

NOTE: Dress wires with a bend as shown in diagram in order to relieve stress when mounting device.

D) The Programmer/Controller will assign a node ID number (Name) for this module.

NOTE: This ID number (Name) will be stored in the controller library to be used for future reference.

NOTE: You may name or edit your device at this time.

E) The dimmer is now installed in the network.

VRCPG

Programmer/

Controller

NOTE: If a dimmer has been successfully Included in the network and the user tries to

Include it again without first excluding it from the network, the module will retain the first node

ID it had received and ignore the second.

NOTE: Remote must be in close proximity to dimmer when including in network.

• Restore power at circuit breaker or fuse.

• Press pad until locator light is OFF. Lights should turn ON. If lights do not turn ON, press the right half of DIM/BRIGHT bar until the lights brighten.

If lights still do not turn ON, refer to the

TROUBLEShOOTING section.

Step 6

Installation may now be completed by tightening mounting screws into wall box. Attach wallplate.

Step 7

Step 8

Dimmer Mounting:

TURN OFF POWER AT

CIRCUIT BREAkER

OR FUSE.

Step 9

Excluding Dimmer from Network:

NOTE: It is very important to accurately Exclude devices from the network when moving or removing a device from a Z-Wave ® network.

This ensures that all information has been removed from your

Programmer/Controller’s information table and is not counted on to be a part of the mesh network.

A) If using a Leviton Z-Wave ® Programmer/Controller, Cat. No. VRCPG, press the Menu button and scroll down to System Setup. Press the center button to select System Setup Menu. Choose Advanced

Settings. Press the center button to select Network.

B) While standing close to the dimmer, press the center button to

<Exclude> device from the network. While the Programmer/Controller is in the Exclusion mode and the locator LED is ON on the dimmer, press the push pad on the dimmer. The Programmer/Controller will verify Exclusion and the locator LED will turn OFF on the dimmer.

If the dimmer is flashing Amber while in the Exlusion mode, the

Programmer/Controller is still trying to communicate with the dimmer.

Wait until the device stops flashing, then press the push pad.

Restore Power:

Restore power at circuit breaker or fuse. Installation is complete.

Including Scene Capable Dimmer into

Z-Wave

®

Network:

Programmer/Controller

Cat. No. VRCPG

NOTES:

• If using a non-Leviton Programmer/Controller, refer to the Programmer/Controller instruction sheet for Including a device.

• If using the VRCPG's Install Checklist feature, go directly to Step B.

A) If using a Leviton Z-Wave ® Programmer/

Controller, Cat. No. VRCPG, press the Menu

Menu

Button button and scroll down to System Setup.

Press the center button to select System

Setup Menu. Choose Advanced Settings.

Press the center button to select Network.

1

ON

2

ON

3 ON

4

ON

OFF

OFF

OFF

OFF

Center

Button

B) While standing close to the module

(approx. 1 ft), press the center button to

<Include> device in the network.

NOTE: Only one device may be included at a time. DO NOT put multiple devices into the Inclusion mode at any time.

C) While the Programmer/Controller is in the Inclusion mode and the

Locator LED is ON on the dimmer, push the push pad to turn ON the dimmer. The Programmer/Controller will verify inclusion and the locator LED will turn OFF on the dimmer.

If the dimmer is flashing Amber while in the Inclusion mode, the

Programmer/Controller is still trying to communicate with the dimmer. Wait until the device stops flashing,then press push pad.

NOTE: If the locator LED on the dimmer turns solid Red while including, there has been a communication error. Refer to

Troubleshooting section.

Factory Default:

If your dimmer is not responding, or you are unable to control it after you have tried to Include/Exclude it multiple times, it may be necessary to reset the dimmer to its original factory settings. To accomplish this, proceed as follows:

• On the dimmer, engage he air-gap switch (refer to Operation

section) and wait 5 seconds. Press push pad back into frame and hold push pad until the locator LED turns Amber and then turns

Red. The dimmer is now reset. Once the dimmer is reset, it will be necessary to Re-Include it to a network before it can be used.

CAUTION: SETTING A DEVICE TO A FACTORY DEFAULT DOES

NOT EXCLUDE THAT DEVICE FROM A NETWORK. THE EXCLUSION

PROCEDURE MUST STILL BE FOLLOWED TO REMOVE THE DEVICE

FROM THE PRIMARY CONTROLLER’S INFORMATION TABLE.

FAILURE TO DO SO MAY RESULT IN A SYSTEM THAT IS SLOW TO

RESPOND, OR MAY FAIL TO RESPOND TO SOME DEVICES.

OPERATION

LED Brightness

Display

NOTE: The locator light will illuminate when the load is in the OFF position to facilitate access in the dark.

NOTE: If using the dimmer in a 3-way application, the lights will turn ON at brightness set on dimmer’s DIM/BRIGHT bar.

The lighting can be controlled from either the dimmer or the remote location.

Push Pad (Default settings)

Turn ON from OFF position:

Tap – Lights turn ON to preset level.

Press and Hold – Lights turn ON to full bright.

Turn OFF from ON position:

Tap – Lights turn OFF.

Push

Pad

DIM/BRIGhT

Bar

Locator

Light

DIM/BRIGhT Bar

BRIGhTEN:

Press right half of DIM/BRIGHT Bar – Lights brighten to desired level.

DIM:

Press left half of DIM/BRIGHT Bar – Lights dim to desired level.

If you continue to hold the left half of the DIM/BRIGHT Bar, the lights will

DIM to minimum level and then turn OFF.

Gently press top NOTE: When lights are OFF you can change the light level that the lights will turn ON to using the

DIM/BRIGHT Bar. of push pad

If there is a power outage, when the power is restored the lights will return to the last setting before the power interruption.

Air-Gap Switch: On the dimmer only, engage the air-gap switch by gently pressing the top of the push pad until the bottom lifts completely out of the frame and a click is heard (refer to Figure). LEDs will turn OFF.

This will cut power to the fixture to replace the bulb. After servicing is complete, push the push pad back for normal operation.

Cleaning: Clean with a damp cloth. DO NOT use chemical cleaners.

ADVANCED PROGRAMMING FEATURES

Definition of A Modes

A-1) Energy Save: Sets the maximum brightness level for energy savings.

A-2) Minimum Brightness Level: Sets the minimum dimming level.

A-3) Preset ON Level: Sets the turn on brightness level regardless of the previous set light level (formerly Dim Lock).

Definition of B Modes

B-1) ON Fade Rate: Sets the amount of time in seconds it takes the lights to turn ON to maximum brightness.

B-2) OFF Fade Rate: Sets the amount of time in seconds it takes the lights to turn OFF from maximum brightness.

B-3) LED Options: Sets the time period in seconds the Locator LED and Brightness display will stay on before extinguishing.

Definition of LEDs

Leftmost LED = LED 1

Rightmost LED = LED 7

NOTES:

• The device will exit programming mode after 3 minutes of inactivity.

• Pressing the push pad at any time during programming will advance the device to the next programming mode.

Program Mode A

1 2 3 4 5 6 7

LED Brightness

Display

To enter Program Mode A:

Press and hold the Push Pad and then the right half of the

DIM/BRIGHT Bar (^) for 5 seconds until the Locator LED and leftmost LED (LED 1) begin to blink.

A-1) Upon releasing the Push Pad and the right half of the

DIM/BRIGHT Bar (^), the Locator LED will continue to blink once per second and the rightmost LED will illuminate to display the device is in Program Mode A-1, Energy Save. The default energy save mode is 100% i.e. full bright. To change the Energy Save level, use the DIM/BRIGHT Bar to move the corresponding LED to the desired discrete preset level according to Chart A. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, A-2.

LED

LED 1

LED 2

LED 3

LED 4

LED 5

LED 6

LED 7 (Default)

Chart A

MAX. BRIGHTNESS

75%

80%

85%

90%

95%

97%

100% (Full Bright)

ENERGY SAVINGS

34% savings

29% savings

24% savings

16% savings

8% savings

5% savings

0% savings

A-2) The Locator LED will blink 2 times per second to indicate the device is in Program Mode A-2, Minimum Brightness Level.

To change the Minimum Brightness Level from 1-50%, use the DIM/BRIGHT Bar. The light output will reflect the minimum brightness level selected. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, A-3.

A-3) The Locator LED will blink 3 times per second to indicate Program

Mode A-3, Preset ON Level. To change the current Preset ON

Level from 1-100%, use the DIM/BRIGHT Bar. If this feature is not desired, press and hold the left half of the DIM/BRIGHT Bar

(v) until no LED is lit (default setting). By tapping the Push Pad this setting will automatically be saved and the device will exit

Programming Mode A.

Program Mode B

To enter Program Mode B:

Press and hold the Push Pad and then the left half of the

DIM/BRIGHT Bar (v) for 5 seconds until the Locator LED and rightmost

LED (LED 7) begin to blink.

B-1) Upon releasing the Push Pad and the left half of the

DIM/BRIGHT Bar (v), the Locator LED will continue to blink once per second indicating he dimmer is in Program Mode B-1, ON

Fade Rate. To change the ON Fade Rate, use the DIM/BRIGHT

Bar to move the LED to the desired preset level according to Chart

B. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, B-2.

B-2) The Locator LED will blink 2 times per second to indicate Program

Mode B-2, OFF Fade Rate. To change the OFF Fade Rate, use the DIM/BRIGHT Bar to move the LED to the desired preset level according to Chart B. By tapping the Push Pad this setting will automatically be saved and the device will advance to the next programming mode, B-3.

LED

LED 1

LED 2 (Default)

LED 3

LED 4

LED 5

LED 6

LED 7

Chart B

FADE ON

0 seconds (instant)

0.5 seconds

1.5 seconds

3.0 seconds

6.0 seconds

10 seconds

25 seconds

FADE OFF

0 seconds (instant)

0.5 seconds

1.5 seconds

3.0 seconds

6.0 seconds

10 seconds

25 seconds

B-3) The Locator LED will blink 3 times per second to indicate Program

Mode B-3, LED Options. To change the LED Options settings, use the DIM/BRIGHT Bar to move the LED to the desired preset setting according to the Chart B-3. By tapping the Push Pad this setting will automatically be saved and the device will exit

Programming Mode B.

LED

LED 1(default)

LED 2

LED 3

LED 4

LED 5

LED 6

LED 7

Chart B-3

LOCATOR LED TIMEOUT

Active

Active

Turns off 5 sec. after use

Turns off 5 sec. after use

Active

Active

Turns off 5 sec. after use

LED BRIGHTNESS DISPLAY OPTIONS

Active

Turns off 5 sec. after use

Active

Turns off 5 sec. after use

LED Bar active

LED Bar turns off 5 sec. after use

LED Bar turns off 5 sec. after use

TROUBLEShOOTING

• Lights Flickering

- Lamp has a bad connection.

- Wires not secured firmly with wire connectors of dimmer or

terminal screws of remote.

- Verify load type is electronic low voltage.

• Light does not turn ON and Locator LED does not turn ON

- Circuit breaker or fuse has tripped.

- Lamp is burned out.

- Neutral not wired to Dimmer (White wire).

• Intermittent dimmer operation

- Minimum load is under 40W.

• Remote does not operate lights

- Ensure that total wire length does not exceed 300 ft (90 m).

- Ensure wiring is correct.

• Lights cycle ON and OFF

- Remove excess load.

For additional information, contact Leviton’s Techline at 1-800-824-3005 or visit Leviton’s website at www.ViziaRFplus.com

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving Antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/tv technician for help.

Protected under U.S. Patent Number 6,388,399 and patents pending and licensed under U.S. Patents Numbers 5,905,442, and 5,982,103

2008 © Leviton Mfg. Co., Inc.

DI-000-VRE06-02A-X2

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.