AER-DEC™-81000/82000/83000/84000

Integrated Sink System

Single/Double/Triple/Quadruple Station Corian® or Quartz Lavatory Systems

Installation

Instruction

Code No. 0816672

Rev.2 (04-15)

AD-81000

Deck Sink Lavatory System

Corian/Quartz (Pages 2-3)

AD-82000

Deck Sink Lavatory System

Corian/Quartz (Pages 4-5)

IMPORTANT

Read this entire installation manual to ensure proper installation.

When finished with the installation, file this manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances is the responsibility of the installers.

Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts.

Make sure that all water supply lines have been flushed and then completely turned off before beginning installation. Debris in supply lines can cause valves to malfunction.

AD-83000

Deck Sink Lavatory System

Corian/Quartz (Pages 6-7)

AD-84000

Deck Sink Lavatory System

Corian/Quartz (Pages 8-9)

Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation. Electrical power MUST remain off until installation is complete.

Installer’s hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out rating of 1,000 lbs.

For standard height mounting, do not exceed the recommended

34” distance from the top of the lav deck to the finished floor. To meet ADA requirements, the lav deck cannot exceed the

34” maximum height dimension.

Wear all proper safety equipment prior to installation.

PRIOR TO INSTALLATION

Important:

• Adequate structural support in or behind the wall is required. Refer to the appropriate rough-in diagram for dry weight of sink.

Refer to pages 10 and 11 for sink and stud support requirements.

•

All plumbing should be installed in accordance with applicable codes and regulations.

• Before connecting flex hoses to supply stops, flush all water lines until water is clear.

• Hot and cold water supply lines/tempered supply line & drain lines.

SUPPLIES REQUIRED FOR INSTALLATION OF SINKS

• 3/8” x 2 1/2” lag screws, wall anchors, bolts (minimum pull-out rating of

1000 Ibs./450 kg). See Frame Mounting Support drawing for required lag screws for your specific lavatory system.

• 1/2” NPT hot/cold or tempered supply piping

• 1 1/2” NPT drain piping

• Adhesive: Loctite ® PL Premium ® FAST GRAB Polyurethane Construction

Adhesive

• 110 volt GFCI protected electrical outlet for 100-120 VAC plug-in transformer

• Screen filter(s) included with faucet(s)

• Backing supplied by others to meet local codes

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants its Products to be made of first class materials, free from defects of material or workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (1 year for SF Faucets, special finishes and PWT electronics and 30 days on PWT software) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR

ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

1

2

LAVATORY SYSTEM ROUGH-IN DIMENSIONS FRONT VIEW SINGLE STATION

LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW SINGLE STATION

LAVATORY SYSTEM ROUGH-IN DIMENSIONS SIDE VIEW SINGLE STATION

LAVATORY SYSTEM ROUGH-IN DIMENSIONS TOP VIEW SINGLE STATION

Hidden drain w/clean-out

out as required

1/2” Backing

DRAIN ASSEMBLY AND FRAME ENCLOSURE MOUNTING SUPPORT SINGLE STATION

2”x10” wood reinforcement between studs

Wood Stud per schedule

GFI 4 gang outlet

Drywall

Backing supplied by others to meet local codes

Hand Dryer Blower Motor w/ Muffler Attachment

Lag Bolts

1.

Measure outside of frame.

Cut-out drywall window

2.

Remove drywall window.

3. Replace with backing supplied by others (per local code).

Frame Enclosure

4. Using mounting template, mount blower motor, soap dispenser pump

(optional) and electrical outlets to backing.

5.

Mount top of frame at 33” above finished floor.

6.

Securely fasten with 1,000 Lb

pull out lag bolts.

12” 12”

33"

6”

6”

Soap Dispenser

*Hole Location for

Mounting Frame

*Due to manufacturing tolerances, all dimensions are for reference only.

12”

MOUNTING FAUCETS, SOAP DISPENSERS & HAND DRYERS / ATTACHING DECK TO FRAME ENCLOSURE SINGLE STATION

12”

MOUNTING FAUCETS

For ease of installation, leave the deck laying on its back.

Install faucets, optional soap dispensers and hand dryers according to manufacturers instructions.

Adhesive

1. For ease of installation, leave the deck laying on its back. Install faucets, optional soap dispensers and hand dryers according to manufacturers instructions.

2. Hook-up air hose to blowers. Do not connect power until air spout is completely installed.

3.

Install all water connections, drain lines and components.

BASYS DRYER SPOUT

SUBASSEMBLY

EHD-510

BASYS SOAP SPOUT

SUBASSEMBLY

ESD-400

FRAME SUPPORT

1. Back edge of Deck may require scribing to finished wall.

2. Shim all gaps between frame and deck,

especialy under trough area.

HOLDING NUT

ASSEMBLY

BAYONET TURN

TO SPOUT

CABLE. LEAVE

UNATTACHED

HOSE & MUFFLER

ASSEMBLY

HOLDING NUT

ASSEMBLY

SOAP DISPENSER

LINES

POWER ADAPTOR

TO LOCK HOSE TO

BLOWER

WALL UNIT BLOWER

MOTOR ASSEMBLY

HAND DRYER

Refer to installation instructions with component.

SOAP DISPENSER

MOTOR ASSEMBLY

SOAP DISPENSER

Refer to installation instructions with component.

3

LAVATORY SYSTEM ROUGH-IN DIMENSIONS FRONT VIEW DOUBLE STATION

Notes:

1. Mount Blower and Soap Dispenser to spec. location.

2. Slip frame over mounted components and properly fasten frame to

backed wall.

3. Hot and Cold water supply lines location subject

LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW DOUBLE STATION

LAVATORY SYSTEM ROUGH-IN DIMENSIONS SIDE VIEW DOUBLE STATION

4

LAVATORY SYSTEM ROUGH-IN DIMENSIONS TOP VIEW DOUBLE STATION

Hidden drain w/clean-out

Grid strainer to be cleaned out as required

1/2” Backing

DRAIN ASSEMBLY AND FRAME MOUNTING SUPPORT DOUBLE STATION

Drywall

2”x10” wood reinforcement between studs

Wood Stud per schedule

Backing supplied by others to meet local codes

GFI 4 gang outlet

Soap Dispenser

Motor

Hand Dryer Blower Motor w/ Muffler Attachment

1.

Measure outside of frame.

Cut-out drywall window

2.

Remove drywall window.

3. Replace with backing supplied by others (per local code).

Wood Screws

Lag Bolts

Frame Enclosure

4. Using mounting template, mount blower motor, soap dispenser pump

(optional) and electrical outlets to backing.

5.

Mount top of frame at 33” above finished floor.

6.

Securely fasten with 1,000 Lb

pull out lag bolts.

33"

12” 12”

12”

12”

6”

6”

*Hole Location for

Mounting Frame

*Due to manufacturing tolerances, all dimensions are for reference only.

MOUNTING FAUCETS / ATTACHING DECK TO FRAME DOUBLE STATION

12”

12”

1. For ease of installation, leave the deck laying on its back. Install faucets, optional soap dispensers and hand dryers according to manufacturers instructions.

2. Hook-up air hose to blowers. Do not connect power until air spout is completely installed.

3.

Install all water connections, drain lines and components.

Adhesive

Adhesive

MOUNTING FAUCET,SOAP DISPENSER & HAND DRYER SPOUTS

For ease of installation, leave the deck laying on its back.

Install faucets, optional soap dispensers and hand dryers according to manufacturers instructions.

FRAME SUPPORT

1. Back edge of Deck may require scribing to finished wall.

2. Shim all gaps between frame and deck,

especially under trough area.

BASYS DRYER SPOUT

SUBASSEMBLY

EHD-510

HOLDING NUT

ASSEMBLY

CONNECT CONTROL

CABLE TO BLOWER

BAYONET TURN

TO LOCK HOSE

TO SPOUT

PROGRAMING

CABLE. LEAVE

UNATTACHED

CONNECT GROUND

WIRE TO BLOWER

HOSE & MUFFLER

ASSEMBLY

BASYS SOAP SPOUT

SUBASSEMBLY

ESD-400

HOLDING NUT

ASSEMBLY

SOAP DISPENSER

LINES

POWER ADAPTOR

BAYONET TURN

TO LOCK HOSE TO

BLOWER

WALL UNIT BLOWER

MOTOR ASSEMBLY

HAND DRYER

Refer to installation instructions with component.

SOAP DISPENSER

MOTOR ASSEMBLY

SOAP DISPENSER

Refer to installation instructions with component.

5

6

LAVATORY SYSTEM ROUGH-IN DIMENSIONS FRONT VIEW TRIPLE STATION

Backing

Notes:

1. Mount Blower and Soap Dispenser to spec. location.

2. Slip frame over mounted components and properly fasten frame to

backed wall.

3. Hot and Cold water supply lines location subject

to local code.

LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW TRIPLE STATION

Backing

LAVATORY SYSTEM ROUGH-IN DIMENSIONS SIDE VIEW TRIPLE STATION

LAVATORY SYSTEM ROUGH-IN DIMENSIONS TOP VIEW TRIPLE STATION

Hidden drain w/clean-out

Grid strainer to be cleaned out as required

81”

1/2” Backing

DRAIN ASSEMBLY AND FRAME MOUNTING SUPPORT TRIPLE STATION

2”x10” Wood

Reinforcement in between studs

(See page 10 for steel stud installation requirements)

Steel/Wood Stud

2”x4” or 2”x6”

(See page 10 for steel stud installation requirements)

Drywall

Backing supplied by others to meet local codes

Hand Dryer Blower Motor w/ Muffler Attachment

Soap Dispenser

Motor

Lag Bolts

Frame Enclosure

1.

Measure outside of frame.

Cut-out drywall window

2.

Remove drywall window.

3. Replace with backing supplied by others (per local code).

4. Using mounting template, mount blower motor, soap dispenser pump

(optional) and electrical outlets to backing.

5.

Mount top of frame at 33” above finished floor.

6.

Securely fasten with 1,000 Lb

pull out lag bolts.

12”

12”

12” 12”

12” 12” 12”

33”

6”

6”

*Hole Location for

Mounting Frame

*Due to manufacturing tolerances, all dimensions are for reference only.

12”

12”

12”

MOUNTING FAUCETS / ATTACHING DECK TO FRAME TRIPLE STATION

Adhesive

1. For ease of installation, leave the deck laying on its back. Install faucets, optional soap dispensers and hand dryers according to manufacturers instructions.

2. Hook-up air hose to blowers. Do not connect power until air spout is completely installed.

3.

Install all water connections, drain lines and components.

Adhesive

MOUNTING FAUCET,SOAP DISPENSER & HAND DRYER SPOUTS

For ease of installation, leave the deck laying on its back.

Install faucets and optional soap dispensers according to manufacturers instructions.

BASYS SOAP SPOUT

SUBASSEMBLY

ESD-400

FRAME SUPPORT

1. Back edge of Deck may require scribing to finished wall.

2. Shim all gaps between frame and deck,

especially under trough area.

BASYS DRYER SPOUT

SUBASSEMBLY

EHD-510

HOLDING NUT

ASSEMBLY

CONNECT CONTROL

CABLE TO BLOWER

BAYONET TURN

TO SPOUT

HOSE & MUFFLER

ASSEMBLY

HOLDING NUT

ASSEMBLY

SOAP DISPENSER

LINES

POWER ADAPTOR

BAYONET TURN

BLOWER

WALL UNIT BLOWER

MOTOR ASSEMBLY

HAND DRYER

Refer to installation instructions with component.

SOAP DISPENSER

MOTOR ASSEMBLY

SOAP DISPENSER

Refer to installation instructions with component.

7

8

LAVATORY SYSTEM ROUGH-IN DIMENSIONS FRONT VIEW FOUR STATION

Notes:

1. Mount Blower and Soap Dispenser to spec. location.

2. Slip frame over mounted components and properly fasten frame to

backed wall.

3. Hot and Cold water supply lines location subject

to local code.

LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW FOUR STATION

LAVATORY SYSTEM ROUGH-IN DIMENSIONS SIDE VIEW FOUR STATION

LAVATORY SYSTEM ROUGH-IN DIMENSIONS TOP VIEW FOUR STATION

31”

31”

7”

31”

6 1/2”

7”

23 1/2”

Hidden drain w/clean-out

Grid strainer to be cleaned out as required

Hidden drain w/clean-out

Grid strainer to be cleaned out as required

Backing

DRAIN ASSEMBLY AND FRAME MOUNTING SUPPORT FOUR STATION

2”x10” Wood

Reinforcement in between studs

(See page 10 for steel stud installation requirements)

Steel/Wood Stud

2”x4” or 2”x6”

(See page 10 for steel stud installation requirements)

Drywall

Backing supplied by others to meet local codes

Lag Bolts

1.

Measure outside of frame.

Cut-out drywall window

2.

Remove drywall window.

3. Replace with backing supplied by others (per local code).

Frame Enclosure

4. Using mounting template, mount blower motor, soap dispenser pump

(optional) and electrical outlets to backing.

5.

Mount top of frame at 33” above finished floor.

6.

Securely fasten with 1,000 Lb

pull out lag bolts.

12” 12”

12”

12” 12”

12”

12”

12”

33”

6”

6”

*Hole Location for

Mounting Frame

*Due to manufacturing tolerances, all dimensions are for reference only.

12” 12” 12”

12”

12” 12”

MOUNTING FAUCETS / ATTACHING DECK TO FRAME FOUR STATION

Adhesive

1. For ease of installation, leave the deck laying on its back. Install faucets, optional soap dispensers and hand dryers according to manufacturers instructions.

2. Hook-up air hose to blowers. Do not connect power until air spout is completely installed.

3.

Install all water connections, drain lines and components.

Adhesive

For ease of installation, leave the deck laying on its back.

Install faucets and optional soap dispensers according to manufacturers instructions.

FRAME SUPPORT

1. Back edge of Deck may require scribing

2. Shim all gaps between frame and deck,

especially under trough area

.

BASYS DRYER SPOUT

SUBASSEMBLY

EHD-510

HOLDING NUT

ASSEMBLY

CONNECT CONTROL

CABLE TO BLOWER

BAYONET TURN

TO LOCK HOSE

TO SPOUT

HOSE & MUFFLER

ASSEMBLY

BASYS SOAP SPOUT

SUBASSEMBLY

ESD-400

HOLDING NUT

ASSEMBLY

SOAP DISPENSER

LINES

POWER ADAPTOR

TO LOCK HOSE TO

BLOWER

HAND DRYER

WALL UNIT BLOWER

MOTOR ASSEMBLY

Refer to installation instructions with component.

SOAP DISPENSER

MOTOR ASSEMBLY

SOAP DISPENSER

Refer to installation instructions with component.

9

SINK BRACKET STUD SUPPORT

COLD FORMED STEEL FRAME MOUNTING SUPPORT

Corian Sink Design Requirements:

Max. sink deck depth = 25”

Max. sink dead weight (including stone and fixture = 10 psf

Max. concentrated live load at edge of sink = 500lbs.

Provide anchor spacing noted within product drawings

Metal Stud per schedule

5” - 18 gauge stud reinforcement between studs

2”x10” wood reinforcement between studs

42"

42"

WOOD FRAME MOUNTING SUPPORT

35"

35"

2'

2'

Wood Stud per schedule

Backing supplied by others to meet local codes

Sink Length

Drywall

Drywall

Sink Length

Drywall

Drywall

Sink System

Enclosure

Backing supplied by others to meet local codes

Sink System

Enclosure

Cold Formed Steel Framing for AD

Series Corian Sinks

Wall/Stud

Height

10”

12”

14”

16”

18”

20”

Depth

3-5/8”

6”

3-5/8”

6”

3-5/8”

6”

3-5/8”

6”

3-5/8”

6”

3-5/8”

6”

Flange

Min.

Gauge

2-1/2” 18

3” 16

1-3/8” 12

1-5/8” 16

2” 16

2-1/2” 16

1-3/8” 16

1-5/8” 18

2” 18

2-1/2” 18

3” 16

1-5/8” 14

2” 16

2-1/2” 16

1-3/8” 14

1-5/8” 16

1-3/8” 14

1-5/8” 16

2” 16

2-1/2” 18

1-3/8” 18

1-5/8” 18

2” 18

2-1/2” 18

3” 16

1-3/8” 14

1-5/8” 16

2” 16

2-1/2” 16

1-3/8” 16

1-5/8” 18

2” 18

2” 18

2-1/2” 18

3” 16

1-5/8” 12

2” 16

2-1/2” 16

1-3/8” 12

1-5/8” 16

2” 18

2-1/2” 18

3” 16

1-5/8” 12

2” 14

2-1/2” 16

1-5/8” 14

2” 18

2-1/2” 18

3” 16

Wood Framing for AD Series Corian

Sinks

Wall/

Stud

Height

Stud

Studs Req.

@16” o.c.

(See Note 1)

Species Grade

10’

12’

14’

16’

2x4

2x6

2x4

2x6

2x4

2x6

2x4

2x6

2

1

3

1

3

1

3

1

SPF No. 2

18’

20’

2x4

2x6

2x4

2x6

3

1

3

2

Note 1: Where mutiple studs are listed, bunch multiple studs and space multiple studs @16” o.c. across width of sink

10

Quartz Sink Design Requirements:

Max. sink deck depth = 25”

Max. sink dead weight (including stone and fixture = 20 psf

Max. concentrated live load at edge of sink = 500lbs.

Provide anchor spacing noted within product drawings

Cold Formed Steel Framing for AD

Series Quartz Sinks

WALL/STUD

HEIGHT

10”

12”

14”

16”

18”

20”

DEPTH

3-5/8”

6”

3-5/8”

6”

3-5/8”

6”

3-5/8”

6”

3-5/8”

6”

3-5/8”

6”

FLANGE

MIN.

GAUGE

2-1/2” 18

3” 16

1-3/8” 12

1-5/8” 14

2” 16

2-1/2” 16

1-3/8” 14

1-5/8” 16

2” 18

2-1/2” 18

3” 16

1-5/8” 12

2” 16

2-1/2” 16

1-3/8” 12

1-5/8” 16

1-3/8” 14

1-5/8” 16

2” 16

2-1/2” 16

1-3/8” 16

1-5/8” 18

2” 18

2-1/2” 18

3” 16

1-3/8” 12

1-5/8” 16

2” 16

2-1/2” 16

1-3/8” 16

1-5/8” 18

2” 18

2” 18

2-1/2” 18

3” 16

1-5/8” 12

2” 14

2-1/2” 16

1-3/8” 12

1-5/8” 16

2” 18

2-1/2” 18

3” 16

1-5/8” 12

2” 14

2-1/2” 14

1-5/8” 14

2” 16

2-1/2” 18

3” 16

Wood Framing for AD Series

Quartz Sinks

Wall/

Stud

Height

Stud

Studs Req.

@16” o.c.

(See Note 1)

Species Grade

10’

12’

14’

16’

2x4

2x6

2x4

2x6

2x4

2x6

2x4

2x6

3

1

3

1

3

1

3

2

SPF No. 2

18’

20’

2x4

2x6

2x4

2x6

3

2

3

2

Note 1: Where mutiple studs are listed, bunch multiple studs and space multiple studs @16” o.c. across width of sink

CLEANING AND MAINTENANCE

Material Description: Corian Material is made from a blend of acrylic modified bio-based polyester resin. Engineered Stone is 90% natural quartz and polyester resin and is resistant to chemicals, stains, burns and impact.

Surface damage can be easily repaired with everyday cleansers or fine grit abrasives.

Routine Cleaning: For regular cleaning, use standard commercial or household products such as Simple Green ® , Creamy Cleanser brand,

Formula 409

®

or Windex

®

.

Stubborn Stains: Remove tough stains, with non abrasive cleaners and pads such as a white Scotch Brite

®

pad and Lysol

®

. Special Situations for

Corian and Engineered Stone

Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse the unit thoroughly after cleaning.

Restoring the surface: Refresh and restore the rich surface with one of the following:

Geo Series: Color enhancer such as Tenax

®

Ager

Pearl Series: Impregnating sealer such as DryTreat Stain - Proof Original™ or Miracle Sealants 511 Impregnator Do not use strong acid or alkaline chemicals and cleansers to clean Engineered Stone. If these chemicals come in contact with the surface, wipe them off immediately and rinse with soapy water. Avoid contact with harsh chemicals such as paint remover, bleach, acetone, etc. Avoid contact with hot pans and objects.

Repair Kits: Corian repair kits are available. Contact your Sloan Stone Sink

Systems representative or distributor for part numbers and pricing. Repair kits are made to order and have a shelf life of 30 days. Engineered Stone shades of color can vary from product to product.

PERIODIC CLEANING OF DRAIN BOX REQUIRED.

BRAND NAMES

Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor does the omission of any brand name cleaner imply inadequacy. Many products named are regional in distribution, and can be found in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products should be used in strict accordance with package instructions.

11

COMPONENTS SINGLE STATION

Deck

Enclosure

Grid Strainer

Assembly

DS-57

Optional

Not Provided

Chrome or

Plastic P-Trap

Rubber Gasket

Slip Washer

Flange Nut

Sloan Optional

Water Temperature Mixing Valves

Mix-60-A Mix-135-A

Shims

FAUCET OPTIONS

Mid Basys High Faucet (EFX Series)

COMPONENTS DOUBLE STATION

Basys Mid Faucet (EFX Series) Basys Low Pedestal Faucet (EFX Series) Basys Low Integrated Faucet (EFX Series) Basys Wall Mount Faucet (EFX Series)

Sloan Optional

Water Temperature Mixing Valves

Deck

Shims

Grid Strainer

Assembly

DS-57

Optional

Not Provided

Chrome or

Plastic P-Trap

Rubber Gasket

Slip Washer

Flange Nut

Mix-60-A Mix-135-A

Enclosure

FAUCET OPTIONS

COMPONENTS TRIPLE STATION

Mid Basys High Faucet (EFX Series)

Basys Mid Faucet (EFX Series) Basys Low Pedestal Faucet (EFX Series)

Basys Low Integrated Faucet (EFX Series) Basys Wall Mount Faucet (EFX Series)

Sloan Optional

Water Temperature Mixing Valves

Deck

Grid Strainer

Assembly

DS-57

Optional

Not Provided

Chrome or

Plastic P-Trap

Rubber Gasket

Slip Washer

Flange Nut

Mix-60-A Mix-135-A

Shims

Enclosure

FAUCET OPTIONS

COMPONENTS FOUR STATION

Deck

Mid Basys High Faucet (EFX Series) Basys Mid Faucet (EFX Series) Basys Low Pedestal Faucet (EFX Series) Basys Low Integrated Faucet (EFX Series) Basys Wall Mount Faucet (EFX Series)

Grid Strainer

Assembly

DS-57

Optional

Not Provided

Chrome or

Plastic P-Trap

Rubber Gasket

Slip Washer

Flange Nut

Sloan Optional

Water Temperature Mixing Valves

Mix-60-A

Shims

Mix-135-A

FAUCET OPTIONS

Enclosure

Mid Basys High Faucet (EFX Series)

Basys Mid Faucet (EFX Series)

Basys Low Pedestal Faucet (EFX Series) Basys Low Integrated Faucet (EFX Series) Basys Wall Mount Faucet (EFX Series)

12

Sloan Valve Company

10500 Seymour Avenue

Franklin Park, IL 60131 [email protected]

www.sloanvalve.com

Tel. 800.982.5839

The information contained in this document is subject to change without notice.

Copyright © 2015 Sloan Valve Company CODE NO. 0816672– Rev. 2 (04/15)