DualForce - SureCall
DualForce
™
2G and 3G Adjustable Dual-Band Signal Booster Kit
User Guide
Thank you for your purchase of SureCall’s DualForce. The DualForce offers many of the
benefits of DAS but at a fraction of the cost. DualForce was specifically designed to
eliminate frustrations over dropped calls, limited range and slow data rates by amplifying
incoming and outgoing cellular signals in homes and offices up to 25,000 square feet and
up to 100 users. DualForce enhances 2G and 3G voice and reception data for all major
U.S. carriers.
If you need any assistance while installing this product please contact tech support at
1-888-365-6283 or email us at: [email protected]
2
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Table of Contents
How It Works
Package Contents
Pg. 4
Pg. 5-6
Installation Overview
Pg. 7
Installing Your Hardware
Pg. 7
Pg. 8
Finding the Strongest Signal
Installing the Outside Anntenna
Installing the Inside Anntenna
Installing Signal Booster
Pg. 9-11
Pg. 12-13
Pg.14
Configure Gain Setting
Pg. 15-18
Troubleshooting
Pg. 19-20
Specification
Pg. 20
Kitting Information
Pg. 21
Warranty
Safety Information
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Pg. 22-23
Pg. 23
3
How It Works
SureCall’s DualForce is a high-quality bidirectional signal booster that enhances cellular
signals to areas that are prone to weak cellular coverage.
DualForce works with two or more antennas:
• Up to four inside antennas that communicate with your cell phone.
• An outside antenna that communicates with the cell tower.
Signals sent from a cell tower are received by the outside antenna, amplified by the
booster and then broadcast to your phone via the inside antenna.
When your phone transmits, the signal is sent to the inside antenna, amplified and then
sent to the cell tower via the outside antenna.
4
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Package Contents
1. Unpack all package contents. For missing or damaged items, contact your reseller.
2. Turn over the signal booster and record the model and serial number for reference:
Serial #: Purchase Date: 3. Keep the carton and packing material to store the product in case you need to return it.
Standard DualForce signal booster packages include the following items:
• One SureCall DualForce booster
• One outside antenna
• Cable for connecting the outside antenna to the signal booster
• One inside antenna
• Cable(s) for connecting the inside antenna to the signal booster
• One power supply
DualForce
Outside Antenna (Option)
Omni
Yagi
SC-400 Cables
Inside Antenna (Option)
Dome
Panel
Note: DualForce is available in four standard kits that are customized to your particular needs. Other kit options available include additional
dome or panel antennas, cables and splitters. For more information see our website or email us at [email protected] Due to the
recent change of our company name from Cellphone-Mate (CM) to SureCall (SC) we have changed the prefix on all of our antennas,
cables and accessories from CM to SC-.
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
5
Package Contents
Installation Overview
Please determine which kit you have from the following list:
Model
Package Options
SC-DUALH/O-72-OD-Kit
1 Outdoor Omni antenna, 1 interior dome antenna, 30’ and 75’ SC400 coax cables
SC-DUALH/O-72-YD-Kit
1 Outdoor Yagi antenna, 1 interior dome antenna, 30’ and 75’ SC400 coax cables
SC-DUALH/O-72-OP-Kit
1 Outdoor Omni antenna with 1 interior panel antenna, 30’ and 75’ SC400 coax cables
SC-DUALH/O-72-YP-Kit
1 Outdoor Yagi antenna with 1 interior panel antenna, 30’ and 75’ SC400 coax cables
For a detailed description, see Kitting Information on page 20.
Antenna Type
Model No.
Usage Coverage
SC-100-L
Omni Antennas are ideal for
topographies with minimal
obstacles. They offer 360˚
hemispherical coverage
Yagi Outdoor Antenna
SC-230W-S
Yagi antennas are for targeted
areas and capable of reaching
cell towers up to 30 miles away
Dome Antenna
SC-222W
Dome antennas are for a central
location with 360˚ coverage
Panel Antenna
SC-248W
Panel Antennas allow optimum
reception to targeted areas
Omni Outdoor Antenna
Warning: Unauthorized antennas, cables, and/or coupling devices are prohibited by FCC new rules. Please contact FCC
for details: 1-888-CALL-FCC. Changes or modifications not expressly approved by SureCall could void the user’s
authority to operate the equipment.
Note: Due to the recent change of our company name from Cellphone-Mate (CM) to SureCall (SC) we have changed the prefix on all of our antennas,
cables and accessories from CM to SC-.
6
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Before You Install
Step 1.Make sure you have positioned the booster close enough to an existing
electrical outlet.
Step 2. Make sure you have sufficient cable length between proposed outside antenna
location and booster connector.
Step 3Make sure you have sufficient cable length between proposed inside antenna
location and booster connector.
Installation Overview
Step 1. Find the outside area that has the strongest signal. (See page 8 for instruction if needed)
Step 2. Install the outside antenna in the area identified in step 1. (See page 9-10 for instruction if
needed)
Step 3. Install the inside antenna. (See page 11-12 for instruction if needed)
Step 4. Mount the signal booster, connect the outside and inside antenna cables to the signal
booster, and connect the booster to an AC power source. (See page 13-14 for instruction
if needed)
Step 5. Configure gain settings on the signal booster if needed. (See page 14 for instruction if
needed)
Outside Omni
DualForce
Inside Domes
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
7
Installing Your Hardware
Step 1. Find
the area with the Strongest Signal
The signal booster requires a minimum cellular signal of low –100 dBm to high –90 dBm.
If your DualForce kit includes an outside omni antenna and you can only achieve cell
phone reception of one bar or less, you may need a DualForce Yagi antenna which is
capable of targeting carrier antenna towers that are up to 30 miles away. Call or email
SureCall for assistance.
Signal readings usually appear as a negative number (for example, -85). The stronger
the signal, the closer it gets to zero (see the graph below). Before installing the outside
antenna, find the area with the strongest cellular signal source from your service provider
by following the directions below. You can also go to www.antennasearch.com to find the
general location of your carrier’s towers.
Measure the strength of the existing cellular signal in various locations.
• Apple iPhones: Dial *3001#12345#* and press Call. In the top-left corner, a number appears instead of bars.
• Android devices: download apps such as “Network Signal Info” in the Google Play store to measure signal
strength. Search check real signal strength to find other cell signal measurement apps.
• Internet: Go to www.speedtest.net
Poor
Good
Outside
Antenna
-60dB
-50dB
-70dB
-80dB
-90dB
-100dB
-110dB
Signal Strength
Excellent
Cell
Tower
2. Select a location away from buildings, walls, trees, hills, and other terrain features that can block
or reflect wireless signals (12-inch clear radius is recommended).
Note: Where you install your outside antenna in relation to the carrier’s cell phone tower also determines signal strength. Although cell phone
carriers try to place towers for maximum coverage, local ordinances and terrain features can restrict tower locations, which can limit signal
strength at your location.
8
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Installing Your Hardware
Step 2. Install the Outside Antenna
1. Outside Omni antennas receive and send signals in a 360º radius. Yagi or directional
antennas work best when pointed in the direction of your cell phone carrier’s cell tower.
Mount the outside antenna as high as possible. If you are installing a Yagi antenna set it
up facing the cell tower in the area where you located the best signal source (see step 1
on the previous page).
2. Make sure that the mounting area has at least a 12” radius clear of obstructions and
other radiating elements.
3. If the mounting area is prone to weak cellular signals or if the density of the roof and ceiling partially block the signal, the booster will operate at its default setting of 65 dB gain,
be sure to place the outside antenna at least 75 feet from the inside antenna for best
performance.
4. Do not co-locate antennas or operate the outside antenna with any other antenna or
signal boosters.
5. Run the SC-400 cable from the outside antenna to the signal booster. Hand tighten the
connection
Note: See next page for outside antenna installation details.
Optional 2 - Outside Yagi
Optional 1- Outside Omni
DualForce
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
9
Installing Your Hardware
DualForce’s omni antenna comes with equipment for mounting on a vertical wall. For best
results the antenna should be mounted in an upright position.
Step 1: Slide both mounting brackets over the mounting sleeve leaving them loose.
Step 2: Remove the plastic thread protector cap from the bottom of the antenna.
Step 3: Slide the coax cable (not included) through the mounting sleeve (with mounting
brackets) and snugly hand tighten the coax cable connector onto the threads at
the bottom of theantenna.
Step 4: Slip the mounting sleeve over the base of the antenna. Align the hole in the
mounting sleeve with the screw hole in the antenna and fasten the two together
using a small machine screw and washer.
Step 5: Space the mounting brackets as wide apart as possible on the mounting sleeveand afterensuring that both brackets are facing the same direction, tighten the
brackets using theset screws.
Step 6: Two Options
(Option one, pole mounting): Mount the entire assembly to a 1 to 2 inch diameter
pole (not included) by placing the U bolts around the pole and tightening them
through the holes in the mounting brackets using the nuts and washers. The
antenna should be mounted with the chrome tip pointing toward the sky (perpendicular to the ground). For best results, the white fiberglass portion of the antenna
should be mounted above the roofline and unobstructed in all directions.
10
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Installing Your Hardware
(Option two, flat vertical surface mounting): The antenna can be mounted to a flat
vertical surface by replacing the U bolts with wood or metal screws (not included). For
best results, the white fiberglass portion of the antenna should be mounted above the
roofline and unobstructed in all directions. Secure the screws through the mounting
brackets directly into the flat vertical mounting surface ensuring that the chrome antenna
tip is pointed towards the sky (perpendicular to the ground).
Note: The small hex wrench included in the package is only used if the cable connector
at the base of the antenna becomes loosened during shipment. Although rare, if
this occurs remove the small round green sticker located at the base of the antenna
and tighten the hex screw using the included wrench until the connector is secure.
Do not over tighten.
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
11
Installing Your Hardware
Step 3. Install the Inside Antenna
Inside antennas come in omni-directional (dome) and flat panel versions.
Antenna Separation Table
Required Between
Outside and Inside Antenna
Amplifier gain
n
atio
par
e
s
a
enn
ant
Min. separation (ad)
40dB
5-6’
45dB
15-20’
50dB
50’
55dB
60’
65dB
75-80’
72dB
100’-110’
Note: A s you can see from the table above, acquiring the recommended inside and outside antenna separation optimizes coverage significantly.
Any reduced antenna separation reduces the booster’s coverage.
1. If your inside antenna is a dome type, mount it on the ceiling in a central location.
2. If your inside antenna is a flat panel, install it against a wall or surface projecting the area
where you want reception. Point the antenna away from the outside antenna.
To avoid interference stay a minimum distance of 3 feet from the panel antenna.
Optional 1- Inside Dome
DualForce
Optional 2 - Inside Panel
Note: see next page for outside antenna installation details.
12
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Installing Your Hardware
The SC-222W multi-band plastic antenna is an omni-directional interior antenna that
gathers signals from all sides. Range of antenna is dependent on three factor:
1) physical obstructions, 2) power generated by booster and 3) reception from outside
signal received and distributed by outside antenna.
Besides the antenna itself, parts include
mounting equipment for either a flat horizontal
surface or a wall. It should be mounted in
an upright position for best results.
Step 1: Drill a 20mm diameter hole in the ceiling. The ceiling
thickness should be 20mm, maximum.
Step 2: Unscrew fixing nut from antenna. Place antenna cable
through hole. Screw the fixing nut back onto antenna
and cable on crawl space side of ceiling and fasten.
Step 3: Attach the N-Female connection from the interior antenna to the cable leading to
the connector labeled INSIDE, on your booster.
Step 4: Tighten fixing nut to secure antenna (do not over-tighten).
• Storage and transportation: Store and place in non-extreme room-temperature and
dry environment
• Attention: This antenna should not be used near open fire or flame
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
13
Installing Your Hardware
Step 4. Install the Signal Booster
1. Select a location for your booster close to a working AC outlet. Do not expose the signal
booster to excessive heat, direct sunlight, moisture, and airtight enclosures.
2. Attach the supplied mounting kit to the booster using the supplied screws. Tighten the
screws with a screwdriver until snug, then add a 1⁄4-to-1/2 turn. Do not over tighten.
3. Orient the signal booster so the LEDs and DIP switches face away from the wall and
the LEDs are seen easily. Then mount the signal booster to the wall using appropriate
screws and/or wall anchors.
4. Connect the outside antenna cable to the signal booster connector marked OUTSIDE.
Hand tighten the connection.
5. Connect the inside antenna cable to signal booster marked INSIDE. Hand-tighten the
connection.
6. Connect the AC power cord to the signal booster.
7. Connect the plug on the other end of the 110V AC power outlet.
8. Turn the booster’s power switch on.
• The signal booster turns on automatically.
• The Power LED lights up to show that the signal booster is ready for use.
• The Alert LEDs flash 5 times on each band to show the band is activated.
Note: If the Power LED does not turn ON or the Alert LEDs continue to flash, see Troubleshooting page 19.
T
his booster is rated for 5-15V input voltage. DO NOT use the booster with a higher voltage power supply. This can damage the booster, cause
personal injury, and void your warranty.
14
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Installing your Hardware
Booster Hardware
The following image shows the key hardware components on the cellullar booster.
Refer to this image as you install your DualForce kit components.
N connector to outside antenna
Alert LED
PCS - 1900 Dip-Swtich
Cellular - 800 Dip-Switch
Power Light (Green)
Programmer
On / OFF
Power Jack
N connector to inside antenna
DIP Switches and Lights
The DualForce Industrial booster has the following indicators and controls:
• PCS Uplink Warning light/DIP switches (1):These DIP switches control the PCS communications
with the cellular tower.
• PCS Downlink Warning light/DIP switches (2):These DIP switches control the PCS amplification
within the building.
• Power light (3): This light should be illuminated or blinking green at all times while the booster is
powered on.
• Cellular Downlink Warning light/DIP switches 4): These DIP switches control the cellular
amplification within the building.
• Cellular Uplink Warning light/DIP switches (5): These switches control the cellular communications with the tower.
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
15
Installing Your Hardware
Step 5. Configure Gain Settings
Facing the front of your booster, find 4 banks of Dual In-line Package (DIP) switches.
These switches allow manual dB gain attenuation for uplink and downlink channels.
• Bank 1 controls PCS communications with the cellular tower.
• Bank 2 controls PCS amplification in the building.
• Bank 3 controls cellular amplification in the building.
• Bank 4 controls cellular amplification with the tower.
The DIP switches in each bank correspond to the following dB gain values:
Switch 1
Switch 2
1 dB
2 dB
Switch 3
Switch 4
Switch 5
8 dB
16 dB
4 dB
For maximum gain on all channels, your booster ships with all DIP switches turned OFF.
This setting should always be your starting point when installing or reinstalling the booster.
To change it, move the DIP switches to the ON or OFF position.
•M
oving a switch down (away from the LEDs) turns OFF the switch and increases
booster gain for the selected channel.
•M
oving a switch up (toward the LEDs) turns ON the switch and decreases booster
gain for the selected channel.
Switch settings are cumulative. This means the total amount of attenuation for a channel
equals the combined dB of all DIP switches in the same bank being set to ON.
To Achieve
16
Set the DIP Switchs in the Same Bank as Follows...
attenuation
SW1
(1 dB)
SW2
(2 dB)
SW3
(4 dB)
SW4
(8 dB)
SW5
(16 dB)
0 DB
OFF
OFF
OFF
OFF
OFF
1 DB
ON
OFF
OFF
OFF
OFF
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Installing your Hardware
To Achieve
Set the DIP Switchs in the Same Bank as Follows...
attenuation
SW1
(1 dB)
SW2
(2 dB)
SW3
(4 dB)
SW4
(8 dB)
SW5
(16 dB)
3 DB
ON
ON
OFF
OFF
OFF
7 DB
ON
ON
ON
OFF
OFF
15 DB
ON
ON
ON
ON
OFF
21 DB
ON
OFF
ON
OFF
ON
31 DB
ON
ON
ON
ON
ON
Note: A
s you see from the table above, attaining the recommended indoor and outdoor antenna separation optimizes coverage significantly. Any reduced
antenna separation decreases the booster’ cellular signal capabilities.
LEDs
A light-emitting diode (LED) appears above each DIP switch bank on the top panel of the
signal booster.
Designation
LED
LED #1
PCS Uplink
LED #2
PCS Downlink
LED #3
Power
LED #4
Cellular Downlink
LED #5
Cellular Uplink
Description
OFF = normal operation.
ON = PCS uplink warning. Power off booster
immediately.
OFF = normal operation.
ON = PCS downlink warning. Power off booster
immediately.
Green ON = booster is receiving power.
OFF = booster is not receiving power.
OFF = normal operation.
ON = cellular downlink warning. Power off
booster immediately.
OFF = normal operation.
ON = cellular uplink warning. Power off booster
immediately.
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
17
Installing Your Hardware
Automatic Shutdown
SureCall boosters that have automatic shutdown work in the following way:
1. The cellular side (LEDs 4 and 5) is usually the first side to experience oscillation. When
oscillation is detected in the uplink and/or downlink, the appropriate red Warning LEDs
flash and Power (LED 3) turns red.
2. If oscillation occurs on the PCS side, LEDs 1 and/or 2 blink as appropriate and Power
(LED 3) turns red due to oscillation.
3. If the problem is not resolved, the affected side shuts down after 30 seconds. In general,
the cellular side oscillates more easily than the PCS side.
4. The booster wakes up and Power (LED 3) turns green. If oscillation resumes, the LEDs
flash as described previously. These 30-second cycles continue for 15 minutes or until
the problem is resolved.
5. If the problem is not resolved within 15 minutes, the booster shuts down automatically
(all LEDs OFF except Power, which is red) and must be reset by unplugging the booster
from the power supply and plugging it back in.
6. To resolve oscillation, increase antenna separation and/or the attenuation.
If you Want to Improve Coverage
• Find a location that receives a stronger signal and relocate the outside antenna to
that location.
• Increase the distance between the outside and inside antennas.
Be sure your signal booster’s dB gain is turned up to maximum gain on each dial (see
page 15).
18
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Troubleshooting
In the event you encounter a problem, follow the suggestions below to resolve the issue.
Problem
Resolution
Signal booster has no power
Verify that the booster switch is turned on.
Connect the power supply to an alternate power source. Be sure
the AC outlet is working and is not controlled by a wall switch that
can cut power to the outlet. If the green POWER LED on the signal
booster is OFF, return the power supply to SureCall. Contact tech
support at 1-888- 365-6283 or [email protected], or go to
www.surecall.com and log on to online support to receive a Return
Merchandise Authorization (RMA).
After installing your signal
booster system, you have no
signal or reception.
Check the strength of the outside signal as close as you can to the
outside antenna (see instructions on page 8).
Double-check all signal booster and antenna cable connections.
Be sure your signal booster’s dB gain is turned up to full power on
each dial (see page 16).
Red Flashing LED
Signal coming into booster from cellular tower is too strong causing the
booster to automatically shut down. There are two possible solutions:
1. Add an inline attenuator to the cable coming into the booster
2. Relocate the outdoor antenna to a location where the signal is weaker.
Your signal booster
restarted and shut down
for 15 minutes, and is now
shut down permanently.
Each SureCall signal booster is equipped with Auto Shutdown to
prevent cell tower interference. The outside antenna may be close
to a cell tower. Move the outside antenna to a location that provides
sufficient distance from the cell tower to prevent the signal booster
from automatically enabling Auto Shutdown. Once away from the
original location, perform the procedure on page 8.
Solid Red LED
Band is off
The Power LED does not
turn ON
Be sure the AC outlet is working and is not controlled by a wall
switch that can cut power to the outlet.
Yellow Flashing LED
Automatic Gain Control (AGC) is adjusting, part of normal operation.
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
19
Specifications
20
Problem
Resolution
Solid Yellow LED
Indicates an inactive band. Light is off while band is active.
Yellow/Red Flashing LED
Oscillation is detected. First try increasing the separation between
the indoor and outdoor antennas. If this doesn’t eliminate oscillation,
lower the dB gain in 5dB increments.
Your signal booster has
no power.
Verify that the switch on the power supply is turned on and red LED is ON.
Connect the power supply to an alternate power source.
Be sure the power source is not controlled by a switch that can remove
power from the outlet.
Check the green POWER LED on the signal booster. If it is OFF, return the
power supply to SureCall. Contact tech support at
1-888-365-6283 or [email protected], or go to www.surecall.com
and log on to online support to receive an RMA.
Product Name
DualForce
Uplink Frequency Range (MHz):
Cellular: 824-849 MHz
PCS: 1850-1915 MHz G Block Included
Downlink Frequency Range (MHz):
Cellular: 869-894 MHz
PCS: 1930-1995MHz G Block Included
Input Impedance:
50 Ω
Maximum Gain:
65dB-Cellular / 72dB- PCS
Noise Figure:
5 dB
VSWR:
≤2.0
Supported Standards:
CDMA, WCDMA, GSM, EDGE, HSPA+, EVDO and all cellular standards
AC Input:
Input AC110V, 60 Hz; Output: DC 9-20V
Maximum Output Power:
1 Watt EIRP
Cable:
SC-400
RF Connectors:
N Female (both ends )
Power Consumption:
<40W
Operation Temperature:
-4ºF to +158ºF
Dimensions:
10.05” x 7.5” x 2”
Weight:
8.05 lbs
FCC (USA):
RSNDUALFORCE
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Specifications
Kitting Information
Component
Outside Antennas*
Outside Cable
Inside Antenna*
Inside Cable
Product Number
Gain / Loss
Cellular 800 MHz
PCS1900 MHz
SC-100-L
8 dBi
9 dBi
SC-230W
10 dBi
10 dBi
SC-400-75NN (75 Feet)
–4.41dB
–6.17dB
SC-248W
7 dBi
10 dBi
SC-222W
3 dBi
SC-400-30NN (30 Feet)
–1.97 dB
6 dBi
–2.67 dB
*All equivalent antennas and cables are suitable for use with the DualForce booster.
Note: Due to the recent change of our company name from Cellphone-Mate (CM) to SureCall (SC) we have changed the prefix on all of
our antennas, cables and accessories from CM to SC-.
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
21
Warranty
Three-Year Product Warranty
SureCall warrants its products for three years from the date of purchase against defects in workmanship and/or materials.
Specifications are subject to change. The three-year warranty only applies to products meeting the latest FCC Certification
Guidelines stated on 2/20/2013 and going into effect April 30, 2014. A two-year warranty applies to any products manufactured
before May 1, 2014.
Products returned by customers must be in their original, un-modified condition, shipped in the original or protective packaging
with proof-of-purchase documentation enclosed, and a Return Merchandise Authorization (RMA) number printed clearly on the
outside of the shipping container.
Buyers may obtain an RMA number for warranty returns by calling the SureCall Return Department toll-free at 1-888-3656283. Any returns received by SureCall without an RMA number clearly printed on the outside of the shipping container will
be returned to sender. In order to receive full credit for signal boosters, all accessories originally included in the signal booster
box must be returned with the signal booster. (The Buyer does not need to include accessories sold in addition to the signal
booster, such as antennas or cables.)
This warranty does not apply to any product determined by SureCall to have been subjected to misuse, abuse, neglect, or
mishandling that alters or damages the product’s physical or electronic properties.
SureCall warrants to the Buyer that each of its products, when shipped, will be free from defects in material and workmanship, and will perform in full accordance with applicable specifications. The limit of liability under this warranty is, at SureCall’s
option, to repair or replace any product or part thereof which was purchased up to THREE YEARS after May 1, 2014 or TWO
YEARS for products purchased before May 1, 2014, as determined by examination by SureCall, prove defective in material
and/or workmanship. Warranty returns must first be authorized in writing by SureCall. Disassembly of any SureCall product by
anyone other than an authorized representative of SureCall voids this warranty in its entirety. SureCall reserves the right to make
changes in any of its products without incurring any obligation to make the same changes on previously delivered products.
As a condition to the warranties provided for herein, the Buyer will prepay the shipping charges for all products returned to
SureCall for repair, and SureCall will pay the return shipping with the exception of products returned from outside the United
States, in which case the Buyer will pay the shipping charges.
The Buyer will pay the cost of inspecting and testing any goods returned under the warranty or otherwise, which are found to
meet the applicable specifications or which are not defective or not covered by this warranty.
Products sold by SureCall shall not be considered defective or non-conforming to the Buyer’s order if they satisfactorily fulfill the
performance requirements that were published in the product specification literature, or in accordance with samples provided
by SureCall. This warranty shall not apply to any products or parts thereof which have been subject to accident, negligence,
alteration, abuse, or misuse. SureCall makes no warranty whatsoever in respect to accessories or parts not supplied by it.
22
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
Warranty
Limitations of Warranty, Damages and Liability:
EXCEPT AS EXPRESSLY SET FORTH HEREIN, THERE ARE NO WARRANTIES, CONDITIONS, GUARANTEES, OR REPRESENTATIONS AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR OTHER WARRANTIES, CONDITIONS,
GUARANTEES, OR REPRESENTATIONS, WHETHER EXPRESSED OR IMPLIED, IN LAW OR IN FACT, ORAL OR IN WRITING.
SURECALL AGGREGATE LIABILITY IN DAMAGES OR OTHERWISE SHALL NOT EXCEED THE PAYMENT, IF ANY, RECEIVED
BY CELLPHONE-MATE, INC. FOR THE UNIT OF PRODUCT OR SERVICE FURNISHED OR TO BE FURNISHED, AS THE CASE
MAY BE, WHICH IS THE SUBJECT OF CLAIM OR DISPUTE. IN NO EVENT SHALL SURECALL BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL, OR SPECIAL DAMAGES, HOWSOEVER CAUSED.
All matters regarding this warranty shall be interpreted in accordance with the laws of the State of California, and any controversy that cannot
be settled directly shall be settled by arbitration in California in accordance with the rules then prevailing of the American Arbitration Association, and judgment upon the award rendered may be entered in any court having jurisdiction thereof. If one or more provisions provided
herein are held to be invalid or unenforceable under applicable law, then such provision shall be ineffective and excluded to the extent of
such invalidity or unenforceability without affecting in any way the remaining provisions hereof.
SAFETY INFORMATION
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers
consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure,
contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas
MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the
FCC or a licensed wireless service provider.
WARNING: E911 location information may not be provided or may be inaccurate for calls served BY USING THIS DEVICE.
48346 Milmont Drive
Fremont, California 94538
USA
888.365.6283
Fax: 510.996.7250
www.surecall.com
SureCall has made a good faith effort to ensure the accuracy of the information in this document and disclaims the implied warranties of
merchantability and fitness for a particular purpose and makes no express warranties, except as may be stated in its written agreement with
and for its customers.SureCall shall not be held liable to anyone for any indirect, special or consequential damages due to omissions or
errors. The information and specifications in this document are subject to change without notice. © 2014. All Rights Reserved. All
trademarks and registered trademarks are the property of their respective owners.
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]
23
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider
and have your provider’s consent. Most wireless providers consent to the use of
signal boosters. Some providers may not consent to the use of this device on their
network. If you are unsure, contact your provider.
You MUST operate this device with approved antennas and cables as specified by
the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any
person. You MUST cease operating this device immediately if requested by the
FCC or a licensed wireless service provider.
WARNING. E911 location information may not be provided or may be
inaccurate for calls served by using this device.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Dirve, Fremont CA 94538 | 1-888-365-6283 | [email protected]
SureCall | 48346 Milmont Drive,
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement