Front Grille (Stainless) Front Grille (Resin)

Front Grille (Stainless) Front Grille (Resin)
LEGACY-4D-2020
Front Grille (Stainless)
Front Grille (Resin)
Instruction Manual
Installation Manual
To the Customer
1. We recommend that the assembly should be carride out in a SUBARU workshop.
No guarantee in case of improper assembly.
2. Pay special attention not to damage vehicle components when removing/installing them.
1 Genuine Part Number and Applicable Model
Front Grille Genuine Part No.
Applicable Model
J1010AG010
J1010AG020
ALL types
ALL types
2 Specifications
1. Primary material (body): ABS plastic
2. Component parts (always make sure to check component parts before beginning installation)
No.
1
Part Name
Qty.
No.
1
2
Front grille
1
Part Name
Installation manual
Qty.
1
2
The mesh portion of part no. J1010AG010 is Stainless mesh.
The mesh portion of part no. J1010AG020 is Resin mesh.
3 Tools Used
Clip remover, regular screwdriver
4 Diagram of Installed Front Grille
Front grille
Sold By:
1
A
5 Installation Procedure
1. Removing the Grille
Clips
(1) Remove the clips on both upper ends of the vehicle
grille (1 each on the left and right sides).
Clips
Box clip
CAUTION
Vehicle parts that have been removed are
reused during installation. Please store
them in a safe place.
(2) Pull the tabs on the 4 box clips located in the top of the
vehicle grill forward while pressing with a screwdriver
to remove the frame upper from the top of the vehicle
grille.
Vehicle
grille
Frame upper
Regular
screwdriver
Box clip
Vehicle grille
(3) Raise up the tabs (2 locations) on the back of the
vehicle grille with the engaging portion of the
bumper and then take out the vehicle grille by pulling it out towards the front of the vehicle.
Vehicle grille
A
ADVICE
A
The vehicle grille can be removed easily
by placing your hands behind the grille and
raising up the tabs (2 locations).
Tabs
Grille
Raise up
Tab
Bumper
Tab cross-section (A – A)
(4) Press the square hole in the top of the vehicle grille
with a screwdriver and remove the box clips (4 locations).
Regular
screwdriver
Box clip
CAUTION
Vehicle parts that have been removed are
Vehicle grille
reused during installation. Please store
them in a safe place.
2
A
2. Relocating Box Clips in Front Grille
(1) Insert the box clips (4 locations) removed in the previous step into front grille 1.
Box clip
Front grille 1
Box clip
(reused)
Front grille 1
3. Installing the Front Grille
(1) Align the locations of the box clips attached to front
grille 1 so that they fit into the square holes in the
frame upper.
Frame upper
Box clip
(2) Press the bottom of front grille 1 tightly against the
bumper, and then push it slowly towards the vehicle in
the horizontal direction so that the 4 tabs on the bottom of the grille catch on the end of the bumper.
(3) Insert the box clips (4 locations) of front grille 1 into
the square holes in the frame upper.
(4) Insert the clips on both ends of front grille 1 (1 each
on the left and right sides) to fasten the vehicle and
bumper.
Clips
(reused)
• Finally, push front grille 1 backward and forward again
to confirm that the bottom tabs (4 locations) are engaged
with the end of the bumper, and repeat the installation
procedure if a problem occurs at this time.
• This completes the installation procedure.
Grille
Tab
Bumper
3
A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement