Thermalright True Spirit 120M Manual
PDF
Download
Document
Advertisement
Advertisement
Thermalright Thermalright True Spirit 120M Assembly package Thermalright True Spirit 120M ×4 × 1 ×4 × 4 ×7 ×4 ×5 ×4 × 1 × 1 × 1 Chill Factor 2g 4 4 × 1 × 4 8 Thermalright True Spirit 120M Intel 775/1155/1156/1366 Exploded view Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com Fan Clip Heatsink Body 120mm Fan M3 L6 Screw Anchoring Mount Mounting Plate Screw Nut Intel Washer(small) Metal Back Plate M3 L10 Screw Backplate cap 1 Component 1 2 4 9 3 5 6 10 7 8 12 11 Chill Factor 14 13 2g 15 1 Heatsink Body ×1 2 Anchoring Mount ×1 3 Metal Back Plate ×1 4 Mounting Plate ×1 5 Screw Nut ×4 6 LGA2011 Type B Screw Pillars x4 7 M3 L10 Screw ×5 8 M3 L6 Screw ×7 9 Intel Washer (small) ×4 10 AMD Washer (big) ×4 11 Backplate cap ×1 12 Thermal paste ×1 13 120mm Fan×1 14 Fan Clip ×4 15 Anti Vibration Strips ×4 The Ultimate Cooling Solutions! www.thermalright.com 2 Installation Instructions: Step 1: 1366 775 1156 1155 Step 1 : Backplate Installation Choose the platform (775/1155/1156/1366)you are in use. Make four M3L10 Screws go through the Metal Back Plate from bottom towards top.And then place the Metal Back Plate on the table. Put the four Washers (for Intel) around the Screw Cylinders. Step 2: Step 2 : backplate cap Note: When installing on a 775 platform, please first insert the Back Plate Cap into the opening on the Back plate. Make sure you have the Cap facing downwards. (Only for 775). Step 4: Step 3: Step 3 : Place the motherboard on top of the Back Plate. See the four Screw Cylinders go through the four holes around the processor socket.Cap the four Screw Cylinders with the four Screw Nuts. Make sure the side with a washer is facing the Back Plate. Step 5: Chill or Fact 2g Chill Step 4 : Place the Anchoring Mount on the Screw Nuts. Use the four M3L6 Screws to fix the Anchoring Mount on to the Screw Nuts. 3 or Fact 2g Step 5 : Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. Step 6: Step 6 : Fan Clip Installation Pass each end of the Fan Clips through the mounting holes on the cooler body. Then stick one Anti Vibration Strip on each side of the cooler. Step 7: Step 7 : Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And then use the two M3L6 screws to secure the Mounting Plate. Step 8: Step 8 : Fan Installation Place the included 120mm Fan onto the Heatsink Body. And then secure it with the 120mm Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the 120mm Fan. Step 9: Step 9 : Installation completed Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! www.thermalright.com 4 Intel 2011 Thermalright True Spirit 120M Exploded view Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com Fan Clip Heatsink Body 120mm Fan M3 L6 Screw Anchoring Mount Mounting Plate Screw Nut 5 Component 1 2 4 9 3 5 6 10 7 8 12 11 Chill Factor 14 13 2g 15 1 Heatsink Body ×1 2 Anchoring Mount ×1 3 Metal Back Plate ×1 4 Mounting Plate ×1 5 Screw Nut ×4 6 LGA2011 Type B Screw Pillars x4 7 M3 L10 Screw ×5 8 M3 L6 Screw ×7 9 Intel Washer (small) ×4 10 AMD Washer (big) ×4 11 Backplate cap ×1 12 Thermal paste ×1 13 120mm Fan ×1 14 Fan Clip ×4 15 Anti Vibration Strips ×4 The Ultimate Cooling Solutions! www.thermalright.com 6 Installation Instructions: Step 1: Step 1 : Screw Pillar Installation Screw on the four LGA2011 Type B Screw Pillars into the Heatsink studs on the ILM Assembly Frame around the processor socket. Step 2: Step 2 : Anchoring Mount Installation Place the Anchoring Mount onto the four LGA2011 Type B Screw Pillars, secure it by tightening it with 4 M3L6 Screws. Step 3: Chill or Fact 2g Chill or Fact 2g Step 3 : Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. 7 Thermalright True Spirit 120M Step 4: Step 4 : Fan Clip Installation Pass each end of the Fan Clips through the mounting holes on the cooler body. Then stick one Anti Vibration Strip on each side of the cooler. Step 5: Step 5 : Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And then use the two M3L6 screws to secure the Mounting Plate. Step 6: Step 6 : Fan Installation Place the included 120mm Fan onto the Heatsink Body. And then secure it with the 120mm Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the 120mm Fan. Step 7: Step 7 : Installation completed Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! www.thermalright.com 8 Thermalright True Spirit 120M AM2/AM2+/AM3/AM3+/FM1 Exploded view Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com Fan Clip Heatsink Body 120mm Fan M3 L6 Screw Anchoring Mount Mounting Plate Screw Nut AMD Washer(big) Metal Back Plate M3 L10 Screw Backplate cap 9 Component 1 2 4 9 3 5 6 10 7 8 12 11 Chill Factor 14 13 2g 15 1 Heatsink Body ×1 2 Anchoring Mount ×1 3 Metal Back Plate ×1 4 Mounting Plate ×1 5 Screw Nut ×4 6 LGA2011 Type B Screw Pillars x4 7 M3 L10 Screw ×5 8 M3 L6 Screw ×7 9 Intel Washer (small) ×4 10 AMD Washer (big) ×4 11 Backplate cap ×1 12 Thermal paste ×1 13 120mm Fan ×1 14 Fan Clip ×4 15 Anti Vibration Strips ×4 The Ultimate Cooling Solutions! www.thermalright.com 10 Installation Instructions: Step 1: AMD Step 1 : Backplate Installation Choose the platform (AMD) you are in use. Make four M3L10 Screws go through the Metal Back Plate from bottom towards top. And then place the Metal Back Plate on the table. Put the four Washers (for AMD) around the Screw Cylinders. Step 2: Step 2 : backplate cap Note: When installing on a 939 platform, please first insert the Back Plate Cap into the opening on the Back plate. Make sure you have the Cap facing downwards. (Only for 939). Step 4: Step 3: Step3 : Place the motherboard on top of the Back Plate. See the four Screw Cylinders go through the four holes around the processor socket.Cap the four Screw Cylinders with the four Screw Nuts. Make sure the side with a washer is facing the Back Plate. Step 5: Chill or Fact 2g Chill Step 4 : Anchoring Mount Installation Place the Anchoring Mount on the Screw Nuts. Use the four M3L6 Screws to fix the Anchoring Mount on to the Screw Nuts. 11 or Fact 2g Step 5 : Applying Thermal Paste Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly. Step 6: Step 6 : Fan Clip Installation Pass each end of the Fan Clips through the mounting holes on the cooler body. Then stick one Anti Vibration Strip on each side of the cooler. Step 7: Step 7 : Mounting Plate Installation Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And then use the two M3L6 screws to secure the Mounting Plate. Step 8: Step 8 : Fan Installation Place the included 120mm Fan onto the Heatsink Body. And then secure it with the 120mm Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the 120mm Fan. Step 9: Step 9 : Installation completed Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete. The Ultimate Cooling Solutions! www.thermalright.com 12 Thermalright True Spirit 120M Intel 775/1155/1156/1366 Explosionszeichnung Wichtig! Bitte prüfen Sie vor der Montage, ob für Ihren Kühler aktualisierte Montagehinweise auf der Webseite www.thermalright.com verfügbar sind. Lüfterklammer Kühlkörper 120 mm Lüfter M3 L6 Schraube Montagerahmen Befestigungsplatte Rändelschraube Intel Unterlegscheibe(klein) Metall Backplate M3 L10 Schraube Backplateeinsatz 13 Komponenten 1 2 4 9 3 5 6 10 7 8 12 11 Chill Factor 14 13 2g 15 1 Kühlkörper ×1 2 Montagerahmen ×1 3 Metall Backplate ×1 4 Befestigungsplatte ×1 5 Rändelschraube ×4 6 LGA2011 Type B Adapterschraube x4 7 M3 L10 Schraube ×5 8 M3 L6 Schraube ×7 9 Intel Unterlegscheibe (klein) ×4 10 (groß) ×4 AMD Unterlegscheibe 11 Backplateeinsatz ×1 12 Wärmeleitpaste ×1 13 120 mm Lüfter ×1 14 Lüfterklammer ×4 15 Anti-Vibrationsstreifen ×4 The Ultimate Cooling Solutions! www.thermalright.com 14 Installationsanleitung: Schritt 1: 1366 775 1156 1155 Wählen Sie die Plattform (775/1155/1156/1366), die Sie verwenden möchten. Führen Sie vier M3L10 Adapterschrauben von unten nach oben durch die Metall Backplate. Legen Sie die Metall Backplate auf den Tisch. Legen Sie die vier Unterlegscheiben (für Intel) auf die Schraubenzylinder. Schritt 2: Beachten Sie bitte: Sofern Sie ein 775 System benutzen, setzen Sie bitte zuerst den Backplateeinsatz in die quadratische Öffnung der Backplate ein und achten Sie darauf, dass diese nach unten weist (nur für Sockel LGA775 erforderlich). Schritt 4: Schritt 3: Platzieren Sie nun das Motherboard auf die Backplate. Achten Sie darauf, dass die vier Schraubenzylinder durch die vier Montagelöcher am Prozessorsockel gehen. Schrauben Sie die vier Rändelschrauben auf die vier Schraubenzylinder. Stellen Sie dabei sicher, dass die Seite mit den Unterlegscheiben zur Backplate gerichtet ist. Schritt 5: Chill or Fact 2g Chill Platzieren Sie den Montagerahmen auf die Rändelschrauben. Verwenden Sie die vier M3L16 Schrauben, um den Montagerahmen auf den Rändelschrauben zu fixieren. 15 or Fact 2g Tr a g e n S i e e i n e h a u c h d ü n n e S c h i c h t Wärmeleitpaste plan auf der Oberseite der CPU und auf der Unterseite des Kühlers auf. Schritt 6: Führen Sie die Enden der Lüfterklammer in die entsprechenden Befestigungslöcher an der Oberund Unterseite des Kühlkörpers. Anschließend kleben Sie einen Anti Vibrationsstreifen an beiden Seiten (links und rechts) der Lüfterauflagefläche. Schritt 7: Platzieren Sie nun den Kühlkörper auf die CPU. Führen Sie anschließend die Befestigungsplatte durch den Kühlkörper und benutzen die beiden M3L6 Schrauben, um die Befestigungsplatte zu befestigen. Schritt 8: Platzieren Sie den mitgelieferten 120 mm Lüfter an den Kühlkörper und sichern ihn mit den Lüfterklammern. Hierzu ziehen Sie an den am Kühlkörper befestigten Klammern, um die Ecken in die Befestigungslöchern im Lüfterrahmen des Lüfters einrasten zu lassen. Schritt 9: Schließen Sie den Lüfterstecker an den CPU PWM Lüfteranschluss auf dem Mainboard an. Bitte prüfen Sie die ordnungsgemäße Funktion vor der Inbetriebnahme Ihres PC. Die Installation ist abgeschlossen. The Ultimate Cooling Solutions! www.thermalright.com 16 Intel 2011 Thermalright True Spirit 120M Explosionszeichnung Wichtig! Bitte prüfen Sie vor der Montage, ob für Ihren Kühler aktualisierte Montagehinweise auf der Webseite www.thermalright.com verfügbar sind. Lüfterklammer Kühlkörper 120 mm Lüfter M3 L6 Schraube Montagerahmen Befestigungsplatte LGA2011 Type B Adapterschraube 17 Komponenten 1 2 4 9 3 5 6 10 7 8 12 11 Chill Factor 14 13 2g 15 1 Kühlkörper ×1 2 Montagerahmen ×1 3 Metall Backplate ×1 4 Befestigungsplatte ×1 5 Rändelschraube ×4 6 LGA2011 Type B Adapterschraube x4 7 M3 L10 Schraube ×5 8 M3 L6 Schraube ×7 9 Intel Unterlegscheibe (klein) ×4 10 (groß) ×4 AMD Unterlegscheibe 11 Backplateeinsatz ×1 12 Wärmeleitpaste ×1 13 120 mm Lüfter ×1 14 Lüfterklammer ×4 15 Anti-Vibrationsstreifen ×4 The Ultimate Cooling Solutions! www.thermalright.com 18 Installationsanleitung: Schritt 1: Schrauben Sie die vier LGA2011 Type B Adapterschrauben in die Gewinde des Montagerahmens, der sich um den Prozessorsockel befindet. Schritt 2: Platzieren Sie den Befestigungsrahmen auf die LGA2011 Type B Adapterschrauben und fixieren ihn mit vier M3L6 Schrauben. Schritt 3: Chill or Fact 2g Chill or Fact 2g Tragen Sie eine hauchdünne Schicht Wärmeleitpaste auf der Oberfläche der CPU und auf der Unterseite des Kühlers auf. 19 Thermalright True Spirit 120M Schritt 4: Führen Sie die Enden der Lüfterklammer in die entsprechenden Befestigungslöcher an der Oberund Unterseite des Kühlkörpers. Anschließend kleben Sie einen Anti Vibrationsstreifen an beiden Seiten (links und rechts) der Lüfterauflagefläche. Schritt 5: Platzieren Sie nun den Kühlkörper auf die CPU. Führen Sie anschließend die Befestigungsplatte durch den Kühlkörper und benutzen die beiden M3L6 Schrauben, um die Befestigungsplatte zu befestigen. Schritt 6: Platzieren Sie den mitgelieferten 120 mm Lüfter an den Kühlkörper und sichern ihn mit den Lüfterklammern. Hierzu ziehen Sie an den am Kühlkörper befestigten Klammern, um die Ecken in die Befestigungslöchern im Lüfterrahmen des Lüfters einrasten zu lassen. Schritt 7: Schließen Sie den Lüfterstecker an den CPU PWM Lüfteranschluss auf dem Mainboard an. Bitte prüfen Sie die ordnungsgemäße Funktion vor der Inbetriebnahme Ihres PC. Die Installation ist abgeschlossen. The Ultimate Cooling Solutions! www.thermalright.com 20 Thermalright True Spirit 120M AM2/AM2+/AM3/AM3+/FM1 Explosionszeichnung Wichtig! Bitte prüfen Sie vor der Montage, ob für Ihren Kühler aktualisierte Montagehinweise auf der Webseite www.thermalright.com vorhanden sind. Lüfterklammer Kühlkörper 120 mm Lüfter M3 L6 Schraube Montagerahmen Befestigungsplatte Rändelschraube AMD Unterlegscheibe (groß) Metall Backplate M3 L10 Schraube Backplateeinsatz 21 Komponenten 1 2 4 9 3 5 6 10 7 8 12 11 Chill Factor 14 13 2g 15 1 Kühlkörper ×1 2 Montagerahmen ×1 3 Multi Plattform Backplate ×1 4 Befestigungsplatte ×1 5 Rändelschraube ×4 6 LGA2011 Type B Adapterschraube x4 7 M3 L10 Schraube ×5 8 M3 L6 Schraube ×7 9 Intel Unterlegscheibe (klein) ×4 10 (groß) ×4 AMD Unterlegscheibe 11 Backplateeinsatz ×1 12 Wärmeleitpaste ×1 13 120 mm Lüfter ×1 14 Lüfterklammer ×4 15 Anti-Vibrationsstreifen ×4 The Ultimate Cooling Solutions! www.thermalright.com 22 Installationsanleitung: Schritt 1: AMD Achten Sie auf die für AMD Sockel vorgesehene Bohrungen in der Multi Plattform Backplate. Führen Sie die vier M3L10 Schrauben jeweils von unten durch diese Bohrungen und legen dann die Backplate auf den Tisch. Legen Sie die vier Unterlegscheiben (für AMD) über die hervorstehenden Gewinde. Schritt 2: Beachten Sie: Bei Verwendung einer AMD Sockel 939 Plattform setzen Sie zuerst den Backplate Aufsatz in die quadratische Öffnung der Backplate ein. Gehen Sie sicher, dass der Aufsatz nach unten zeigt. Schritt 4: Schritt 3: Platzieren Sie das Mainboard von oben auf die Backplate, so dass die hervorstehenden Schraubengewinde durch die Löcher um den Prozessorsockel gehen. Schrauben Sie die Rändelschrauben auf die vier Schraubengewinde. Achten Sie dabei darauf, dass die Seite mit der Unterlegscheibe zur Backplate zeigt. Schritt 5: Chill or Fact 2g Chill Setzen Sie den Montagerahmen auf die Rändelschrauben. Verwenden die vier M3L6 Schrauben, um den Montagerahmen auf den Rändelschrauben zu befestigen. 23 or Fact 2g Tragen Sie eine hauchdünne Schicht Wärmeleitpaste auf der Oberfläche der CPU und auf der Unterseite des Kühlers auf. Schritt 6: Führen Sie die Enden der Lüfterklammer in die entsprechenden Befestigungslöcher an der Oberund Unterseite des Kühlkörpers. Anschließend kleben Sie einen Anti Vibrationsstreifen an beiden Seiten (links und rechts) der Lüfterauflagefläche. Schritt 7: Platzieren Sie nun den Kühlkörper auf die CPU. Führen Sie anschließend die Befestigungsplatte durch den Kühlkörper und benutzen die beiden M3L6 Schrauben, um die Befestigungsplatte zu befestigen. Schritt 8: Platzieren Sie den mitgelieferten 120 mm Lüfter an den Kühlkörper und sichern ihn mit den Lüfterklammern. Hierzu ziehen Sie an den am Kühlkörper befestigten Klammern, um die Ecken in die Befestigungslöchern im Lüfterrahmen des Lüfters einrasten zu lassen. Schritt 9: Schließen Sie den Lüfterstecker an den CPU PWM Lüfteranschluss auf dem Mainboard an. Bitte prüfen Sie die ordnungsgemäße Funktion vor der Inbetriebnahme Ihres PC. Die Installation ist abgeschlossen. The Ultimate Cooling Solutions! www.thermalright.com 24 Thermalright True Spirit 120M Technical Spec Heatsink Specifications: Dimension: Length 132mm x Width 57.72mm x Height 145.15mm Weight: 784g (including fan and mounting brackets) Heatpipe: 6mm heatpipe*4 units Copper Base: C1100 Pure copper nickel plated Fan Specification: Dimension: L120mm x H120mm x W25mm Weight: 95g Fan speed: 700~1500RPM (PWM controlled) Fan noise: 28.5dBA MAX (Test distance 1.0M) Airflow: 53.3CFM MAX Connector: 4 Pin (PWM Fan connector) 25 Thermalright True Spirit 120M 29.93 145.15 57.72 53.44 132 40 30 16 The Ultimate Cooling Solutions! www.thermalright.com 26 Thermalright True Spirit 120M Thermalright True Spirit Series True Spirit 140 27 True Spirit 120 True Spirit 90 The Ultimate Cooling Solutions! www.thermalright.com TEL: +886-2-8663-6630 FAX: +886-2-8663-6645 EMAIL: [email protected] ">

Public link updated
The public link to your chat has been updated.
Advertisement