Pelco SM5200, WS5080 Network Video Recorder Installation Manual
Below you will find brief information for Network Video Recorder SM5200, Network Video Recorder WS5080. The Network Video Recorder SM5200 and Network Video Recorder WS5080 are designed for recording and managing video data from IP cameras. The units can be used to view live and recorded video, and also to manage camera settings and access control for cameras. They are designed for installation in either a rack or on a desktop.
advertisement
Endura
®
Hardware
For SM5200 and WS5080 Models
INSTALLATION MANUAL
C4687M-D | 12/14
Contents
Important Notices
Regulatory Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Radio and Television Interference
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Warranty Statement
For information about Pelco’s product warranty and thereto related information, refer to www.pelco.com/warranty.
Legal Notice
SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE
IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF
SUCH CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT
FROM RECORDED SUBJECTS. YOU ARE SOLELY RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR
STRICT ADHERENCE TO ANY/ALL RIGHTS OF PRIVACY AND PERSONALTY. USE OF THIS EQUIPMENT AND/OR SOFTWARE FOR ILLEGAL
SURVEILLANCE OR MONITORING SHALL BE DEEMED UNAUTHORIZED USE IN VIOLATION OF THE END USER SOFTWARE AGREEMENT
AND RESULT IN THE IMMEDIATE TERMINATION OF YOUR LICENSE RIGHTS THEREUNDER.
3
4
Video Quality Caution
Frame Rate Notice Regarding User Selected Options
Pelco systems are capable of providing high quality video for both live viewing and playback. However, the systems can be used in lower quality modes, which can degrade picture quality, to allow for a slower rate of data transfer and to reduce the amount of video data stored. The picture quality can be degraded by either lowering the resolution, reducing the picture rate, or both. A picture degraded by having a reduced resolution may result in an image that is less clear or even indiscernible. A picture degraded by reducing the picture rate has fewer frames per second, which can result in images that appear to jump or move more quickly than normal during playback.
Lower frame rates may result in a key event not being recorded by the system. Judgment as to the suitability of the products for users' purposes is solely the users' responsibility. Users shall determine the suitability of the products for their own intended application, picture rate and picture quality. In the event users intend to use the video for evidentiary purposes in a judicial proceeding or otherwise, users should consult with their attorney regarding any particular requirements for such use.
Package Contents
Figure 1: Package Contents
1 System Hardware
2 USB Key: Might include installer software, a recovery image, and the installation and operation manuals.
3 Accessory Pack
4 Hard Drive Pack (hard drives in carriers)
5 Standard USB Keyboard (1 ea. for workstation models only)
6 Rack Mount Kit (1 ea.)
5
6
Figure 2: Accessory Pack Contents
1 Standard USB Mouse (1 ea.)
2 Bezel Keys (2 ea.)
3 Standard US Power Cord (1 ea.)
4 Power Cord (based on country designation, 1 ea.)
NOTE
: Units shipped to China do not include power cords.
5 Chassis Handles (2 ea.); includes Phillips screws for installation.
6 Rubber Feet (4 ea.)
Figure 3: Rack Mount Kit Contents
1 Sliding Mounting Brackets (2 ea.)
2 Rear Mount Rails (2 ea.), Front Mount Rails (2 ea.)
3 L-Shaped Plate Nuts (4 ea.)
4 M5*8L-H2.5 Round Head Nickel Screws (18 ea.), M4*6L-H2.5 Round Head Nickel Screws (18 ea.), 4.2*11*0.8
Nickel Washers (10 ea.)
Tools and Parts Required for Installation
The following installation tools and parts are needed for installation, but are not supplied.
• Power source (110/220 VAC)
• Small Phillips screwdriver, if mounting the unit into a rack
7
8
Product Overview: Front
Figure 1: Server Models: Front Panel Layout (Bezel Open)
Figure 2: Workstation Models with-DVD: Front Panel Layout (Bezel Open)
Figure 3: Front Bezel Indicators (Bezel Closed)
1
Unit Status
• Green: The unit is functioning normally.
• Flashing green: The unit is starting or shutting down.
• Amber: The unit is nearing operational thresholds; maintenance is recommended.
• Red: The unit is in an error condition.
2
Network Port 1 Speed and Activity
• Off: The unit is not connected to the network.
• Solid green: The unit is connected to the network using the 1000Base-T standard.
• Solid amber: The unit is connected to the network using the 100Base-T standard.
• Solid red: The unit is connected to the network using the 10Base-T standard.
NOTE
: Use the 1000Base-T standard.
3
Network Port 2 Speed and Activity
• Off: The unit is not connected to the network.
• Solid green: The unit is connected to the network using the 1000Base-T standard.
• Solid amber: The unit is connected to the network using the 100Base-T standard.
• Solid red: The unit is connected to the network using the 10Base-T standard.
NOTE
: Use the 1000Base-T standard.
4
Software Status
• Green: The software is operating normally.
• Amber: A minor software malfunction is detected (for example, an excessive network packet loss).
• Red: A fatal software error has occurred (for example, ceasing to record).
5
Power Button
• Push the power button to turn the unit on or off.
• Push and hold the power button for a hard shutdown.
6
Drive Status
• Flashing green: The read or write activity on a specific hard drive.
• Solid red: A problem exists with the hard drive.
• Flashing green/red: The unit is initializing the hard drive
7
USB Ports
The unit has five USB ports: one on the front panel (USB 2.0 port) and four on the rear panel (two USB 3.0 and two USB 2.0 ports).
Use these ports to connect a UPS unit, or conduct diagnostic and troubleshooting activities.
9
Product Overview: Rear
Figure 1: Rear Panel Layout
3
4
1
2
11
12
9
10
13
7
8
5
6
Rear Chassis Fan
Power Receptacle
VGA Port
Ethernet Ports
• Network Port 1 (left is primary)
• Network Port 2 (right is secondary)
Expansion Slots
Serial Ports
Reserved (do not use)
Audio Output
Audio Input
USB 3.0 Ports
USB 2.0 Ports
DisplayPort Connectors
Digital Visual Interface (DVI) Connector
Placing on a Desktop
WARNING
: Do not place the unit on its side; in this position, the unit is likely to fall over and may cause equipment damage or personal injury.
1.
Verify that the rubber feet are attached to the bottom of the unit. If not, secure the rubber feet to the bottom of the unit.
2.
Position the unit to allow for cable and power cord clearance at the rear.
10
Mounting Requirements
The unit can be mounted in an industry standard 48 cm (19-inch) equipment rack and occupies two rack units (RU) of vertical rack space
(8.9 cm or 3.5 inches). The hardware necessary to mount the unit into a rack is supplied with the unit.
NOTE
: The unit must be placed on a desktop to install an optional 4-port capture card, a RAID controller card, or a SCSI card. Make sure these cards are installed properly and performing as expected before placing the unit in the rack.
The rack must meet the following requirements:
• Rack standard:48 cm (19 in.), EIA-310-D compliant (rear column required)
• Rack column depth:50.8 to 76.2 cm (20 to 30 in.)
• Column mounting hole provisions:10-32 UNF-2B threaded holes or square window holes on front and rear columns
• Door systems (optional): Front doors must have at least 5.1 cm (2 in.) between the unit bezel and the inside of the door. Rear doors may be used only on rack columns that are more than 66 cm (26 in.) deep.
Mounting in a Rack
Do not block slots and openings in the cabinet. These provide ventilation to prevent the unit from overheating. Never place the unit near or over a radiator or heat register. When placing the unit in a rack, be sure to provide proper ventilation.
1.
Install the chassis handles: a.
Align the screw holes on the chassis handles and the chassis.
b.
Insert and tighten the four 10-32 x 0.5-inch Phillips flat head screws with a Phillips screwdriver.
2.
Remove the chassis brackets from the sliding brackets: a.
Slide each chassis bracket away from the sliding bracket until it locks in place.
b.
Press the release lever up or down (depending on the rail) to release the chassis bracket from the sliding bracket. Press down on the release lever for the right set of rails and press up for the left set of rails.
Figure 1: Remove the Chassis Brackets from the Sliding Brackets
11
12
3.
Attach one chassis bracket to each side of the unit. Use four M4*6L-H2.5 round head nickel screws for each bracket. Attach the chassis brackets so that the slotted ends are positioned toward the rear of the unit.
Figure 2: Attach the Mounting Brackets
4.
If necessary, remove the rubber feet from the underside of the unit.
5.
Attach a front and rear L-shaped bracket to the left and the right sliding brackets using two M4*6L-H2.5 round head nickel screws.
Leave all eight of the screws untightened.
Figure 3: Attach the L-Shaped Mounting Brackets
6.
Attach the front and rear L-shaped brackets to the rack. Make sure the rails are mounted back to back. Use two M5*8L-H2.5 round head nickel screws for each bracket.
The mounting brackets are identical and can be used on either side of the rack.
a.
Position the ear of the front L-shaped bracket and an L-shaped plate nut against the inside front of the equipment rack. Align the two center holes in the ear of the L-shaped bracket and L-shaped plate nut with the holes in the rack.
b.
Using two M5*8L-H2.5 round head nickel screws, insert and tighten the screws from the outside of the rack, pointing toward the back of the rack.
c.
Adjust the rails to the correct depth of the equipment rack by sliding the rear-mount rail to the back of the equipment rack.
d.
Repeat the previous steps to attach the rear L-shaped bracket and L-shaped plat nut to the rack.
Figure 4: Attach the Brackets to the Rack
7.
Tighten the M4*6L-H2.5 round head nickel screws that are attached to the front- and rear-mount rails which were left untightened earlier in the installation.
8.
Place the unit onto the mount rails by sliding the chassis brackets onto the rails. Align the chassis brackets with the first slot on the sliding brackets when installing the unit. This will ensure that the two brackets are aligned properly when sliding the unit in and out of the rack. It might require two people to lift and slide the unit into place.
NOTE
: To pull the unit completely out of the rack, pull the unit out of the sliding bracket until it locks into place, and then press the release levers on either side of the chassis bracket to release the unit.
Figure 5: Install the Unit in the Rack
Figure 6: Align the Chassis Bracket and the Sliding Bracket
9.
Insert and tighten two M5*8L-H2.5 round head nickel screws above and below the chassis handles to secure the unit in the rack.
13
Installing the Drive Array
Drives and drive bays are numbered 1 through 6. You must install the drives in their corresponding bays in numerical order.
When replacing a drive in a RAID array, you should rebuild the array before operating. If another drive fails before the array is rebuilt, the array will go off line and data loss will occur.
WARNING
: The hard drive parts and assemblies are susceptible to damage by Electrostatic Discharge (ESD). Follow safe handling procedures when replacing hard drives.
Figure 1: Drive Bay Allocation for Models with 6 Bays
1 SSD; contains the OS
2 SSD; RAID 1 OS
3 HDD; RAID 5 Export Storage
4 HDD; RAID 5 Export Storage
5 HDD; RAID 5 Export Storage
6 HDD; RAID 5 Export Storage
Figure 2: Drive Bay Allocation for Models with DVD Drive
1 SSD: Contains operating system, install first
2 HDD: for additional storage (optional)
3 HDD: for additional storage (optional)
4 HDD: for additional storage (optional)
5 DVD drive
14
1.
Unlock and open the bezel.
2.
Install the drive carriers: a.
Open the drive latch (grasp the latch right side and pull it to the left).
b.
Slide the drive carrier into the drive bay.
c.
Close the hard drive latch; ensure that the drive carrier locks into place.
3.
Close and lock the bezel.
15
Connecting the Power Supply
1.
Connect the power cord to the unit’s power connector.
2.
Connect the other end of the power cord to the appropriate power source.
Connecting an Uninterruptible Power Supply
While UPS units supply backup battery power, the unit works in conjunction with the SmartUPS from APC. The SmartUPS signals the unit to begin a graceful shutdown if the UPS standby power falls below a specific threshold.
1.
Shut down the unit.
2.
Connect a power cord from the unit power supply to a standard wall outlet.
3.
Connect a power cord from the UPS to a standard wall socket or other power source.
4.
Connect a USB cable from the APC SmartUPS to the USB connector on the unit.
5.
Turn on the UPS.
6.
Turn on the unit.
USB
POWER SOURCE
OUTPUT POWER
INPUT POWER
UPS
Figure 1: Connecting a UPS
16
Starting Up the Unit
1.
Unlock and open the bezel.
2.
Press the power button.
3.
Close and lock the bezel.
Shutting Down the Unit
Use an orderly shutdown for the unit to close files and power down.
Use the immediate shutdown in an emergency or when there is not enough time for an orderly shutdown.
Orderly Shutdown
1.
Click Start.
2.
Click Shut Down.
Immediate Shutdown
1.
Unlock and open the bezel.
2.
Press and hold the power button until the unit shuts down.
3.
Close and lock the bezel.
17
Connecting to the Network
The primary network interface card (NIC) must be active when using the License Key Entry program to add or update IP camera licenses.
1.
Connect one end of an Ethernet cable one of the unit’s network interfaces.
2.
Connect the other end of the cable to an available Gigabit Ethernet port.
NETWORK
SECONDARY
Figure 1: Network Cable Connection
18
Migrating Data to a SM5200 from a SM5000
You must configure the network interface and DHCP settings on the SM5200 to match the settings from the SM5000 before performing the migration process, or you will lose these settings in the migration process.
For a quick and seamless transition to a new system manager, you can transfer your database and settings from your existing SM5000 to a new SM5200.
The migration process requires a flash drive with an empty boot record and a Windows-based client on the Endura network with Endura
Utilities version 2.3.3 or later installed. It is recommended that you use the Pelco flash drive included with your SM5000 for data migration.
Data migration does not include primary network interface settings or settings for features new and specific to the SM5200. You must manually configure these settings.
Do not replace your existing system manager until your SM5200 is fully configured and operational. Only the admin user can log on to the SM5200. If the admin user exists in the database you are migrating to the SM5200, the user will login to the SM5200 using his or her current password. If the admin user does not exist before migration, then the admin user will login using the default password.
1.
Connect your Pelco flash drive to a Windows-based client on the Endura network.
2.
Open Endura Utilities.
3.
Right-click SM5000 in the System Attributes tab.
4.
Select SM Backup.
5.
Select the flash drive as the backup location and click OK. This creates a folder on the flash drive named the IP address of the
SM5000 you are backing up. The folder will contain a UtilitiesBackup.tgz file.
6.
Copy UtilitiesBackup.tgz to the root directory of the flash drive.
7.
Remove the flash drive from the client computer, and connect it to the SM5200.
8.
Turn on the SM5200. After a short boot process, the four lights on the right side of the unit’s front panel turn solid amber, indicating that the system is importing UtilitiesBackup.tgz. This process may take several minutes.
9.
Remove the flash drive when the software status light turns off, indicating that the migration process is complete. The SM5200 restarts 30 seconds after the migration process has completed. Remove the flash drive within 30 seconds of the completed migration process or once the unit has fully rebooted; do not remove the flash drive during the boot process.
NOTE
: Upon completing the migration process, the SM5200 creates a file called .sm5000-migrated in the root directory of the flash drive, preventing the SM5200 from attempting to import UtilitiesBackup.tgz multiple times.If data fails to migrate properly, or you want to reuse the flash drive to perform the migration process on another SM5200, delete the.sm5000-migrated file.
19
Technical Specifications
Hardware
Processor
Internal Memory
SM5200
WS5080
Operating System
SM5200
WS5080
Storage
SSD
HDD
Drive Bays
SM5200
WS5080
Optical Drive
USB Ports
Intel ® Xeon ® E3-1275 v3
16 GB DDR3 RAM ECC
8 GB DDR3 RAM Non-ECC
Embedded Linux
Windows 7 Ultimate 64-bit SP1
120 GB (OS)
4 TB
6 (2 SSD in RAID1, up to 4 HDD)
4 (1 SSD, 3 Unused)
DVD±RW (WS5080 only)
3 USB 2.0 ports (1 front, 2 rear), 2 USB 3.0 ports (rear)
Video
Video System
Max Resolution
Video Outputs
Video Standards
Video Decoding Supported
Video Display Modes
Decoding Performance
Intel HD Graphics P4700 (shared memory)
3840 x 2160 per DisplayPort output (2x)
1920 x 1200 @ 60 hz on DVI-D output
1920 x 1200 @ 60 hz on VGA output
Supports up to 3 simultaneous displays using any combination of the four outputs
60 Hz capable for NTSC
75 Hz capable for PAL
MPEG-4 ASP; H.264 Baseline, Main, and High profiles
1 image, 4 images (2 x 2), 9 images (3 x 3), 16 images (4 x 4), 6 images (1 large + 5 small), 10 images (2 large + 8 small), 13 images (1 large + 12 small); High definition monitors can also display 6 images (3 x 2) and 12 images (4 x 3)
16X real-time MPEG-4 streams at 704 x 480; 12X real-time H.264 Baseline profile streams at 704 x 480;
4X H.264 Baseline profile streams at 720p; 2X real-time H.264 Baseline profile streams at 1080p
Audio
Audio Decoding
Audio Bit-rate
Audio Levels
Input
Output
Audio Connectors
Connector Tip
Connector Ring
20
G.711 speech codec
64 kbps
Electret microphone
Up to 3 Vp-p, adjustable, minimum load of 8 ohms
2, 3.5 mm stereo jacks
Signal left (input and output)
Signal right (input and output)
Audio
Connector Sleeve
Audio Inputs
Audio Outputs
Network
Interface
Common
Microphone
Speaker or line out
2 Gigabit Ethernet RJ-45 port (1000Base-T)
Front Panel
Buttons
Indicator
Unit Status
Primary Network
Secondary Network
Software Status
Hard Disk Status
Green, amber, red
Green, amber, red
Green, amber, red
Green, amber, red (based on diagnostics)
Green, red, off (behind bezel)
Power
Power Input
Power Supply
Power Consumption
100 VAC
115 VAC
220 VAC
100 to 240 VAC, 50/60 Hz, autoranging
Internal
Operating Maximum
160 W, 1.60 A, 547 BTU/H
160 W, 1.39 A, 547 BTU/H
160 W, 0.72 A, 547 BTU/H
Environmental
Operating Temperature
Storage Temperature
Operating Humidity
Maximum Humidity Gradient
Operating Altitude
10° to 35°C (50° to 95°F) at unit air intake (front of unit)
–40° to 65°C (–40° to 149°F)
20% to 80%, noncondensing
10% per hour
–15 to 3,048 m (–50 to 10,000 ft)
Operating Vibration 0.25 G at 3 Hz to 200 Hz at a sweep rate of 0.5 octave/minute
NOTE
: The temperature at the unit air intake can be significantly higher than room temperature. Temperature is affected by rack configuration, floor layout, air conditioning strategy, and other issues. To prevent performance failure and unit damage, make sure the temperature at the unit is continuously within the operating temperature range.
Physical
Construction
Finish
Front Panel
Chassis
Dimensions
Steel cabinet
Gray metallic with black end caps
Black matte finish
50.8 x 43.4 x 8.9 cm (20" D x 17.1" W x 3.5" H)
21
Physical
Mounting Desktop (feet) or rack (2 RU per unit)
SM5200 Models
Use the following table to create a model number for your SM5200. For example, the model number for an SM5200 with 4 TB of storage and a United Kingdom power cord would be SM5200-04-UK.
Model Storage Country Code
4 TB US = North America
Description
SM5200
16 TB
AU = Australia
AR = Argentina
EU = Europe
UK = United Kingdom
SM5200 hardware/software with regional power cord
CN = China
SM5200 hardware/software without power cord. Units shipped to China do not include a power cord.
WS5080 Models
Use the following table to create a model number for your WS5080. For example, the model number for a WS5080 workstation with a
United Kingdom power cord would be WS5080-UK.
Model Country Code
US = North America
Description
WS5080
AU = Australia
AR = Argentina
EU = Europe
UK = United Kingdom
WS5080 hardware/software with regional power cord
CN = China
WS5080 hardware/software without power cord. Units shipped to China do not include a power cord.
Supplied Accessories
Keyboard
Mouse
USB Drive containing Resource and Recovery materials
Windows 7 Ultimate Disc with License (WS5080 Only)
Rack Mount Kit
Power Cord
NOTE
: Units shipped to China do not include power cords.
Optional Software Accessories
WS5200-MAP Endura Mapping interface
Certifications
CE, Class A
FCC, Class A
UL/cUL Listed
22
Certifications
S-Mark for Argentina
CCC
C-Tick
Standards/Organizations
Pelco is a member of the MPEG-4 Industry Forum
Pelco is a member of the Universal Plug and Play (UPnP) Forum, Steering Committee
Pelco is a member of the Universal Serial Bus (USB) Implementers Forum
Pelco is a contributor to the International Standards for Organization / Electrotechnical Commission (ISO/IEC) Joint Technical Committee 1
(JTC1), “Information Technology,” Subcommittee 29, Working Group 11
Compliance, ISO/IEC 14496 standard (also known as MPEG-4)
Compliance, International Telecommunication Union (ITU) Recommendation G.711, “Pulse Code Modulation (PCM) of Voice Frequencies”
23
Pelco by Schneider Electric
3500 Pelco Way Clovis, California 93612 USA
(800) 289-9100 Tel (800) 289-9150 Fax
+1 (559) 292-1981 International Tel
+1 (559) 348-1120 International Fax
www.pelco.com
Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates.
ONVIF and the ONVIF logo are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies.
Product specifications and availability are subject to change without notice.
© Copyright 2014, Pelco, Inc.
All rights reserved.
advertisement
Key Features
- 6 Drive Bays (SM5200)
- 4 Drive Bays (WS5080)
- DVD±RW drive (WS5080 only)
- Supports up to 3 simultaneous displays
- Intel® Xeon® E3-1275 v3 Processor
- 16 GB DDR3 RAM ECC (SM5200)
- 8 GB DDR3 RAM Non-ECC (WS5080)
- MPEG-4 ASP; H.264 Baseline, Main, and High profiles decoding
- G.711 speech codec decoding
- 2 Gigabit Ethernet RJ-45 port (1000Base-T)
