Russound TVA2.1 Installation manual

TVA2.1

2-Channel Digital Amplifier

Installation Manual

SAFETY INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER. NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

2 Russound TVA2.1 Installation Manual

Introduction

The Russound TVA2.1 is a 2-channel low-profile amplifier, designed to be used to bring Better Sound for TV by allowing a high quality, easy-to-use, easy-toinstall amplifier to be added to any television installation.

Its thin footprint means the TVA2.1 can be hidden behind the television or mounted in an in-wall panel behind a television for convenience. The builtin IR learning function allows for ANY typical remote control to be used and eliminates the need for an external control system. This can dramatically reduce the cost of adding additional rooms of audio to a home and keeps the operation simple and intuitive for the homeowner by letting them use their current remote control device.

The 2 channels of amplification are available for up to two pairs of 8-ohm speakers, while also offering a connection for a subwoofer to enhance a room’s sound.

The TVA2.1 provides an array of useful features, such as IR Learning, use of a high quality low-profile external IR sensor, an LED Power Light that can be toggled on and off, as well as a low-profile chassis design.

The high quality class-D digital amplifier sends a respectable 30 Watts per channel of power into 8 ohms. There is a line level subwoofer output to support

2.1 Audio, making the TVA2.1 an easy solution for improving the audio quality in any room with enhanced bass response.

The TVA2.1 features three input options for flexibility. A traditional analog

RCA line level input, and both Digital Coax and Optical S/PDIF. The TVA2.1 also supports 24bit/96khz digital audio in a PCM stereo format.

Product Features

• Class-D amplifier 2 x 30W RMS into 8 ohm

• 24-bit/96kHz S/PDIF support

• S/PDIF, optical and analog line level inputs

• 4-pole speaker detachable screw connector and line level RCA subwoofer

output

• IR Learning for basic volume control.

• Small footprint with mounting options for discreet installation

• External 24v power supply

PRODUCT OVERVIEW

Thermal Protection

All Russound amplifiers are designed with special circuitry to safeguard the amplifier under a thermal overload condition. Thermal protection mode can only engage when the unit has been run at high volume for extended periods of time without adequate ventilation and/or when speaker impedances are below the minimum levels for the amplifier. If this fault occurs, turn off the amplifier, and check that the speaker impedance rating is above the minimum rating. Also check for adequate ventilation around the amplifier and make adjustments if necessary. Once the unit has cooled to safe operating temperatures, the amplifier may be powered back on.

Protection Circuitry

All Russound amplifiers are designed with special circuitry to safeguard the amplifier under a short-circuit condition. A faulty speaker can also cause a short circuit condition. The front panel LED illuminates orange when the amplifier is in short circuit protection. If this fault condition occurs, turn off the amplifier and check speakers for short circuit conditions when appropriate.

Mounting

The mounting wings on the sides of the TVA2.1 can be used for various mounting options:

1. Mounting into a structured wiring type behind-the-tv box. The width of the TVA2.1 does not allow 6” on-center holes, but the TVA2.1 can be secured on either side and a simple Zip Tie can be used for securing the amplifier in any location within the structured wiring box.

2. Mounting to the rear of a TV using any 3rd party VESA type mounting panel, or simply by attaching it to a TV mount. The thin form factor allows it to fit on many tilt or pivot type mounts. In this type of installation, it is recommended to disable the Power LED light so that it does not bother the end user.

3. Wall Mounting (screws not included) – The installer can easily mount the

TVA2.1 to a wall or cabinet.

Russound TVA2.1 Installation Manual 3

FRONT PANEL CONNECTORS

1 2 3 4 5 6 7 8 9 10 11 12

MUTE

IR CONTROLLER

TVA2.1 Digital Amplifier

1 Power Switch: Turns the amplifier On/Off. This switch does not disconnect the main power feed from the amplifier; this requires that the power cord be unplugged from the outlet, or from the rear of the TVA2.1.

2 Power LED: On start-up, the power LED (next to the power switch) lights red to show power on. This will remain on, but can be disabled to remove distraction when installed behind a TV.

Note: Disabling the LED will only disable the "normal" power status LED. The

LED will always illuminate for any trouble conditions and for the first 2 minutes during power up of the device.

3

Power Supply: The TVA2.1 requires a 24VDC (3.75A) power supply which is included. The external dual voltage 24VDC 3.75A power supply provides high output power to support the full range of amplifier operation.

By using an IEC compatible outlet, international customers will be able to easily swap power cords with the appropriate plug type for their market.

4 Speaker Outputs: The speaker outputs are in parallel to the zone amplifier output. We recommend using 6-8 ohm speakers with the TVA2.1.

5 Subwoofer Output

6

Audio Line Input: Analog stereo audio input for a single input source.

7 Optical Input: Digital optical input for a single input source.

8 Coaxial Input: Digital coaxial input for a single input source.

TVA2.1RC Remote Control

9 IR Sensor: Receives the IR commands during the IR Learning process.

This sensor is used only for IR Learning. The external IR Receiver is used during operation of the TVA2.1 for controlling volume and mute.

10 IR Input: 3.5mm jack for an IR Receiver. A Russound IR Receiver is included.

If wiring your own 3.5mm plug to a receiver, the tip - is positive and the sleeve is negative. The external IR receiver is used to control the volume of the TVA2.1 using a standard remote control once the commands have been taught to the

TVA2.1.

11

IR Confirm LED: Provides a visual confirmation that the TVA2.1 is receiving

IR Signals when in the IR Learning Mode only.

12

IR Learning Button: Press for 2 seconds to initiate the IR Learning mode feature.

Press and Hold for at least 10 seconds during power up to toggle the use of the

Power LED during normal operation.

Remote Control

The TVA2.1 comes supplied with a small credit card sized three button remote control that can be used for independent volume commands if a 3rd party remote control system is being used. For most installations, the supplied credit card remote will not be used.

The TVA2.1 features IR learning for the purpose of using a pre-existing TV or Universal Remote.

4 Russound TVA2.1 Installation Manual

TVA2.1RC Remote Control

Simple TVA2.1 Amplifier Programming Instructions

Learning IR Mode Setup

This process allows you to learn the three volume-related IR commands

(Vol +, Vol -, and Mute) from your current remote control.

1. Press the IR Learning Button for 2 seconds until the IR Confirm LED blinks slowly.

2. Place your remote control about 3-4 inches (7-10cm) away from the IR

Learning window of the TVA2.1, aiming the remote directly at the IR Learning window.

3. Press the TV remote’s Vol + key until the IR Confirm LED blinks for 1 second.

4. Press the remote’s Vol – key until the IR Confirm LED blinks for 1 second.

5. Press the remote’s Mute– key until the IR Confirm LED blinks for 1 second.

6. Confirm proper operation of all three volume commands. If any of the three commands must be re-learned, all three commands must be relearned in order. Repeat ALL 6 steps again; then re-test for proper operation.

Note: The TVA2.1 exits the IR Learning Mode automatically after learning the

Mute command.

The Vol +, Vol -, and Mute commands must be learned in sequence

(1st Vol+, then Vol -, then Mute.)

Power LED Disabling (Toggle)

In some installations, such as bedrooms, it may be desirable to disable the

Power LED so that it is not visible in a dark room.

To disable the Power LED:

1. Press and hold the IR Learning Button for approximately 10 seconds while powering on the TVA2.1 until the IR LED (next to the IR Learning Button) begins to blink. The IR Confirm LED will blink twice when toggling from

"Enabled" to "Disabled" and will blink once when togging from "Disabled" to Enabled". Once the IR Confirm LED has blinked, you can release the IR

Learning Button.

Note: After powering on the TVA2.1 Amplifier, the Power LED will always remain on for the first 2 minutes of operation EVEN IF you have disabled it. If the Power LED has been disabled, it will turn off after 2 minutes has passed.

The LED will always illuminate for any trouble conditions. Disabling the LED only affects the LED for normal status conditions.

To Enable the Power LED, repeat the same process.

TV Settings

Certain settings must be changed on the TV when using the TVA2.1. Refer to your TV's owner's manual for exact instructions for your particular TV. These settings are typically found in the TV's setup configuration menu.

1. Disable TV Speakers - Since you will be using the TVA2.1 for all of your TV audio, your TV's internal speakers should be disabled.

2. If using a digital audio signal from your TV to the TVA2.1, make sure that the TV is configured to use stereo PCM for its audio output.

Connecting loudspeakers

The TVA2.1 is designed to be used with a pair of either 6 or 8 ohm speakers.

Speaker connections should only be made while the TVA2.1 is powered off.

The TVA2.1 features a removable, screw-down speaker terminal.

RSF-610

IR

Receiver

Remote Control

Russound TVA2.1 Installation Manual

PROGRAMMING INSTRUCTIONS

TVA2.1

Typical TVA2.1 Amplifier Installation

RSF-610

Power Supply

Subwoofer

5

TECHNICAL SPECIFICATIONS

Audio Inputs: Stereo Line Level, coaxial or optical (PCM format)

Outputs: 30W per channel at 8 ohms <1% THD+N

Speaker out - removable screw-down connector for up to 12AWG wire,

Subwoofer out - (RCA) with integrated 120Hz low pass filter

IR Sensor Input: 3.5mm stereo jack

Amplifier Channels: 2

Signal-to-Noise Ratio: >90dB 20Hz to 20KHz

Frequency Response: 40Hz to 20KHz +/- 1dB, 20Hz -3dB, Sub Out: -3dB at 170Hz

Input Impedance: >22 ohms

Power Requirements: 24VDC 3.75A (External power supply)

Dimensions: 6.0”H x 9.875”W x 1.375”D (15.2 x 25.0 x 3.5 cm)

Weight: 2.0lbs. (0.9kg)

6 Russound TVA2.1 Installation Manual

LIMITED WARRANTY

The Russound TVA2.1 Amplifier is guaranteed against all defects in materials and workmanship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor.

For this warranty to apply, the unit must be installed and used according to its written instructions. If service is necessary, it must be performed by Russound.

The unit must be returned to Russound at the owner’s expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor is damage resulting from abuse or from servicing by an agency or person not specifically authorized in writing by Russound.

This Warranty does not cover:

• Damage caused by abuse, accident, misuse, negligence, or improper installation or operation

• Power surges and lightning strikes

• Normal wear and maintenance

• Products that have been altered or modified

• Any product whose identifying number, decal, serial number, etc. has been altered, defaced or removed.

Russound sells products only through authorized Dealers and Distributors to ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy. Any sale of products by an unauthorized source or other manner not authorized by Russound shall void the warranty on the applicable product.

Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, the unit must be shipped to Russound at the owner’s expense, along with a note explaining the nature of service required. Be sure to pack the unit in a corrugated container with at least three (3) inches of resilient material to protect the unit from damage in transit.

Before returning a unit for repair, call Russound at (603) 659-5170 for a Return

Authorization number. Write this number on the shipping label and ship to:

Russound

ATTN: Service

1 Forbes Road

Newmarket, NH 03857

Due to continual efforts to improve product quality as new technology and techniques become available, Russound/FMP, Inc. reserves the right to revise system specifications without notice.

Russound TVA2.1 Installation Manual 7

©2015 Russound. All rights reserved.

All trademarks are the property of their respective owners.

Specifications are subject to change without notice.

TVA2.1

Digital Amplifier

Installation Manual

Russound, Inc.

1 Forbes Road, Newmarket, NH 03857 tel 603.659.5170 • fax 603.659.5388

email: [email protected] www.russound.com

28-1396 08.27.15, Rev. 3