EKE CPU-140, SCU-100, MSU-140, CTU-100, ADU-140, KPD-100, KPD-140, SEN 140, SEN 141, SEN OUT, TT 50-SD Smarthome system Installation instructions

EKE CPU-140, SCU-100, MSU-140, CTU-100, ADU-140, KPD-100, KPD-140, SEN 140, SEN 141, SEN OUT, TT 50-SD Smarthome system Installation instructions

Below you will find brief information for Smarthome system CPU-140, Smarthome system SCU-100, Smarthome system MSU-140. This document provides instructions on how to install and configure your Smarthome system. It includes information on connecting devices, defining input/output ports, setting up security and more. The system is designed for easy installation and configuration, and this document will guide you through each step of the process.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Smarthome system CPU-140, SCU-100, MSU-140 Installation instructions | Manualzz

INSTALLATION INSTRUCTIONS and

BASIC SYSTEM CONFIGURATION

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

2/23

Contents

1. Warnings & Notes ............................................................................................................................. 3

2. Installation of system to electrical cabinet or modular box ............................................................. 3

3. Powering the system ......................................................................................................................... 7

4. Make connection to the system ....................................................................................................... 8

5. Defining input / output ports of the units ........................................................................................ 9

5.1 Security unit devices ............................................................................................................... 10

5.2 Measurement unit devices ..................................................................................................... 11

5.3 Control unit devices ................................................................................................................ 11

5.4 Adjustment devices ................................................................................................................. 12

5.5 Keypads ................................................................................................................................... 12

5.6 Virtual IO ................................................................................................................................. 13

5.7 EnOcean wireless devices ....................................................................................................... 13

6. General Settings .............................................................................................................................. 13

6.1 Mobile User Interface ................................................................................................................... 13

6.2 Room profiles ................................................................................................................................ 13

6.3 Network settings and search of cameras ...................................................................................... 14

6.4 Setting cameras ............................................................................................................................. 14

6.5 Setting numbers for GSM modem ................................................................................................ 14

6.6 Backup and restore ....................................................................................................................... 14

6.7 System diagnostic ......................................................................................................................... 14

7. Setting light switches and buttons .................................................................................................. 14

8. Setting security system ................................................................................................................... 15

9. Contact information ........................................................................................................................ 16

APPENDIX I: Circuit diagrams .................................................................................................................. 17

Copyright © EKE Group. All Rights Reserved

1. Warnings & Notes

200091-A

2015-08-01

Only approved electrician should do the installation to secure that there will not be danger of electrical shocks.

Installation should be secured so, that the end user does not have possibilities to touch system wirings or parts that may have live voltages

System should be installed to dry place where it cannot get wet. Water can cause risk of fire.

3/23

Do not try to fix, change or disassemble system parts. If some part is faulty, order a new one.

If system or its part is faulty and must be disposed, do it according to local laws.

2. Installation of system to electrical cabinet or modular box

Reserve necessary space from electrical cabinet, or install system to separate modular box. Refer to

‘product cards’ on system parts and dimensions. On the table 1 are listed typical installation accessories needed.

Table 1. Installation accessories

Modular box or electrical cabinet

UTP CAT 5/6 cable

AWG 20/10 or similar cable

Cable ties

WLAN router

Ethernet cable with RJ-45 connector

TT-50SD Current transformers

Sensors and actuators like

- Light switches / push buttons

- Intermediate relays

- Temperature sensors

- Siren

- Door & window contacts

- …

Protection class IP22 or greater

Minimum size 12-MOD (PSU+CPU)

Low voltage wirings

Wirings of intermediate relays & contactors

To secure wirings

To establish a local area network

To connect CPU and computer to router

To set up power consumption measurements

On the table 2 and figure 1 are shown typical order of components when installed to electrical cabinet.

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

Table 2. Typical layout on electrical cabinet

AC 230V feed cables

Circuit breakers

Intermediate relays & Contactors

Measurement Units (MSU) – Control Units (CTU) – Adjustment Units (ADU)

Power Supply (PSU) – Central Processing Unit (CPU) – Security Units (SCU)

4/23

Figure 1. System parts on electrical cabinet

Keep system, its cabling & other low voltage parts separate from AC 230V parts. System is always installed in following order from left to right: CPU – SCU’s – MSU’s – CTU’s – ADU’s.

Start installation of units by pressing bottom pieces to the DIN rail as shown on figure 2.

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

5/23

Figure 2. Installation of bottom pieces.

Connect next power cable CBL-140 to the end of CPU’s bottom piece. It will attach only in one way. If you need to extend bus to other DIN rail use extension cable CBL-101. Connect power cables to +24 VDC PSU and to the backup battery. Remember to connect terminal block to last unit’s bottom piece. Terminal block is shown on figure 3.

Figure 3. Terminal block to last unit’s bottom piece.

Before installing the units to bottom pieces, make sure that bottom pieces do not have powers on. This may harm units and/or mess the software of the system.

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

6/23

Figure 4. +24V PSU and its voltage control screw.

Finalize installation by connecting CPU and possible modules to bottom pieces. Make sure that these lock in to their places as shown on figure 5.

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

7/23

Figure 5. Installation of CPU and modules.

3. Powering the system

Attach Ethernet cable between CPU and WIFI router. If you not aim to use WIFI network attach also cable between computer and router. Power up the router. If customer have internet connection available e.g. ADSL modem, connect it to WAN port of the router.

Connect first backup battery to the system and after that power up the PSU. If the backup battery is not present when system powers up, the boot up will take longer time, since system tries to detect battery and check if it is possible faulty.

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

Monitor the CPU units display. It should show diagnostic values as shown on table 3.

8/23

Table 3. Typical diagnostic values of CPU-140.

Voltages

Value

4.90 – 5.2V 11.0 – 14.5V 23.9 – 24.2V

(PSU 5V) (BAT VDC) (PSU 24V)

Current and temperaturas 0 – 500 mA K10-30C C10-55C

(current) (chasis) (CPU)

Units

IP address

AAC # informs how many modules detected. E.g. AAC 3/3

Shows the system IP address. E.g. 192.168.0.2. If there is a text ‘NO LINK!’ check the connections of Ethernet cables

If the system failed to detect all the units installed, switch off the power sources and check bottom pieces and extension cable connections.

4. Make connection to the system

Write IP address to your browser navigation bar. If you use WIFI network make sure that you are connected to it. You should now see main screen as shown on figure 6. If the main screen is in

Finnish go and change it to English by selecting:

‘ASETUKSET’ – ’JÄRJESTELMÄ’ – ’TYÖKALUT’ – ’KÄYTTÖLIITTYMÄN KIELI’ – English

Select after this ’TALLENNA’.

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

9/23

Figure 6. Main screen of Smarthome by EKE system.

5. Defining input / output ports of the units

Rise up first rights to make system configuration. Click lock icon on upper right side of the screen. Default username and password is: ‘admin / admin’. Click next armor icon on the upper right side of the screen. Rise your rights up to level 3. The default PIN code is ‘1234’.

Units I/O configuration is done either by loading pre-configuration (if delivered with the system) or by manually. If you have pre-configuration file go to:

‘SETTINGS‘ – ‘SYSTEM’ – ‘TOOLS’

Select file to PRE CONFIGRATION that you have and upload it to the system. From this page you can also shut down and reboot the system. Use of ‘Shut down’ is recommended since this way

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

10/23 you can make sure that software closes its tasks in a controlled manor. Further possible system updates can be loaded via this page.

If you do not have the pre-configuration file, or you must do some changes go to

‘SETTINGS’ – ‘IO INTERFACES’ - and select the unit you want to configure

On each units configuration you must give a name that describes the device. E.g. for light switch

‘corridor front switch’. Some inputs can be set so that they are ‘normally closed or open’ which means e.g. on door contacts that it activates alarms on open or closed state.

You can define system I/O ports while you connect physical devices to the system. For connections of devices refer to appendix I: Circuit diagrams.

Following tables gives names of devices you can select & their function.

5.1 Security unit devices

Table 4. Security devices

+12V Output ports

+12V Output

Alarm light

Emergency lighting

Outdoor siren

Silent alarm

Siren

Function

Power e.g. for 12V motion detector (PIR)

Low power (<2W) Led light

Low power (<2W) Led light

Siren 12V

E.g. emergency light at bedroom

Siren 12V

Input ports (potential free switches) Function

Cabinet tamper Sabotage switch at electrical cabinet

Carbon monoxide detector

Circuit breaker

CO alarm switch to detect if one circuit breaker is turned off

Device alarm

Door sensor

Door sensor tamper

Emergency button

Glass break sensor

Glass break sensor tamper

Potential free contact alarm e.g. from air condition unit

Magnet switch of door or window

Sabotage switch of door sensor

Switch to launch alarm e.g. from bedroom

To detect glass break

Sabotage switch of glass break sensor

Motion detector

Motion detector tamper

Residual current device

Smoke detector

Smoke detector tamper

Tamper detector

WDS-100

Water leak detector

Water leak detector tamper

Detect motion (PIR)

Sabotage switch of PIR

Alarm from residual current switch

Fire alarm

Sabotage switch of smoke detector

General sabotage switch

EKE Water leak detector

Generic water leak detector

Sabotage switch of water detector

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

11/23

5.2 Measurement unit devices

Table 5. Measurement devices

TEMPERATURE PORT

FSN-100

PSN-100

SEN-100 Temperature

SEN-101 Humidity

SEN-101 Temperature

SEN-140 Temperature

SEN-141 Humidity

SEN-141 Temperature

SEN-1xx Illumination

SEN-OUT Illumination

SEN-OUT Temperature

SSN-100 Temperature

Pulse Input

Function

EKE floor temperature sensor

EKE pipe temperature sensor

EKE temperature sensor (not available)

EKE humidity sensor (not available)

EKE Temperature sensor (not available)

EKE Temperature sensor (without humidity)

EKE Humidity sensor

EKE Temperature sensor (with humidity)

EKE Light level sensor

EKE Outdoor light level sensor

EKE Outdoor temperature sensor

EKE Temperature sensor for Sauna

Function

Electricity x imp / y Wh

Energy x imp / y Wh

Night electricity switch

Pulse input

Electricity meter that gives x impulses / y Wh

Energy meter that gives x impulses / y WH

Switch that shows when night time energy is in use

Generic potential free input

Water meter x imp / y l Water meter that gives x impulses / y liter

Voltage input Function

Carbon dioxide 0…2000PPM (0..10V) CO

2

meter with 0..10V output

Humidity 0..100% (0..10V)

I25

Humidity meter with 0..10V output

Current meter with 0..10V output with max. 25A

I50

TT50-SD

TT50-SD Three phase

Temperature

Voltage input

Current meter with 0..10V output with max. 25A

Current clamp

Current clamp to measure average current from one phase on 3-phase devices

Temperature transmitters with different scales

Generic voltage measurement between 0..10V

5.3 Control unit devices

Table 6. Control devices

+24V Output ports

Just select any device!

Function

Different devices just shows different icons on main UI

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

12/23

INPUTS

Button

Motion detector

Switch

Twilight switch

5.4 Adjustment devices

Table 7. Adjustment devices

+24V Output ports

24V Output

24V Motor

Relay Output

Relay Output

Voltage Output

0..10V Output

Dimmer x..10V

Motor x..10V

Ventilation unit 0..10V

Current x..20mA Output

Dimmer x..20mA

Motor 0..20mA

Function

If you have push button in use select this

If you have PIR to control lights select this

If you have lever switch select this

If you have twilight switch to control lights select this

Function

Generic 24V Output e.g. for curtains

24V Motor e.g. to cut off water

Function

Connect to devices that takes switch input for control.

E.g. some ventilation units. Max. Voltage / Current

48V/100mA.

Function

Generic 0..10V / 20mA max output

Use to control dimmers

Use to control voltage driven motors

Use to control ventilation that takes 0..10V input

Function

Use to control devices with current messages

Use to control dimmers with current messages

Use to control motors with current messages

5.5 Keypads

If you have keypads in use, you can define what functions can be found behind number buttons.

Table 8. Adjustment devices

Widget

Measurement value

Electricity consumption

Incomplete tasks

Custom message

Date

Function

Shows selected measurement value. E.g. oudoor temperature

Shows consumption value

Shows incomplete tasks if setup to the system (not in use on with mobile user interface

You can enter custom message here

Shows date

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

13/23

Clock

Network info

Shows clock

Shows system IP number and star if remote access is available

5.6 Virtual IO

From this menu you can combine two inputs to one virtual so that e.g. with below certain light level and motion detection lights are turned automatically on. Consult EKE for details about programming language / setup.

5.7 EnOcean wireless devices

If you have wireless extension installed, you can pair each device via this menu. Pairing is done by setting first device and then selecting ‘PAIR’. During pairing you must push switch or push pairing button until it comes visible to the system.

Table 9. EnOcean devices

Device x-Button switch

Temperature EKE

Temperature & Humidity EKE

Relay Eltako xxx

Temperature & Humidity ELTAKO

Carbon dioxide Enoluz 24V

Illumination Eltako FAH60

Water leak detector FWS81

Eltako Smoke alarm

Temperature RH% and CO2

6. General Settings

Function

Switch with x buttons to control lights

EKE wireless temperature sensor

EKE wireless temperature & humidity sensor

Eltako relay, type xxx

Eltako Outdoor temperature & humidity sensor

Enoluz CO

2

sensor

Eltako outdoor light level sensor

Eltako water leak detector

Eltako fire detector

Eltako combined temperature, humidity and CO

2

sensor

Here are described some general setting that should be done.

6.1 Mobile User Interface

From ‘SETTINGS’ – ‘USER INTERFACE’ – ‘MOBILE’ you can define what functionality & devices are visible to user at mobile user interface. Simple select functionality / device you will to see.

6.2 Room profiles

From ‘SETTINGS’ – ‘PROFILE SETTINGS’ – ‘ROOM PROFILES’ you can define what is the state of the devices when system is in different modes. Set at least ‘HOME’ and ‘AWAY’ profiles. You can select either

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

- ‘NO CHANGE’ so device state will not change,

- ‘ON’ so device turns on on this profile,

- ‘OFF’ so device will turn off on this profile or

- ‘xx %’ for example level of dimmer

6.3 Network settings and search of cameras

14/23

Go to ‘SETTINGS’ – ‘SYSTEM’ – ‘NETWORK SETTINGS’. Edit ‘EMAIL SETTINGS’ if you wish to use email alarm notifications. Fill corresponding server names, user name and password that internet provider offers.

If you have cameras connected to system (to the router or via WIFI), you can scan those from this page. Just click ‘SCAN’. Take up the cameras IP addresses that system has detected. E.g.

192.168.0.19 b0:c5:54:16:05:f2 D-LINK INTERNATIONAL

6.4 Setting cameras

Got to ‘SETTINGS’ – ‘SECURITY SETTINGS’ – ‘CAMERAS’. Add new camera by with ‘+’ button.

Select camera model, and to field ‘IP’ give the IP number you discovered on previous point.

6.5 Setting numbers for GSM modem

Go to ‘DOCUMENTS’ – ‘CONTACTS’ and add new contact with ‘+’ button. Fill the names and phone numbers to whom you wish system to send messages.

6.6 Backup and restore

From ‘SETTINGS’ – ‘SYSTEM’ – ‘SYSTEM BACKUPS’ you can create a backup of configuration

‘Create a backup’ or upload existing one to system by ‘Upload a backup’.

6.7 System diagnostic

From ‘SETTINGS’ – ‘SYSTEM’ – ‘DIAGNOSTICS’ you will see if any error occurs. This is shown on red text and with exclamation mark ‘!’. If you need to take contact to support, it is essential that you markup CPU serial number that is shown on top under section ‘SYSTEM INFORMATION’ after phrase ‘Serial Number’. This identifies the system for remote use and to the manufacturer.

7. Setting light switches and buttons

To define function of switches and buttons connected to the system go to ‘CONTROL’ –

‘BUTTON’ page. Press the button you want to configure. If you do not know which button is in

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

15/23 case, you can push it and if connected properly it will turn yellow. For the push buttons you can define following functions shown on table 10.

Table 10. Functions for push buttons.

Function

Device

Home profile

Room profile

Control Group

Dimmer adjustment

Ventilation level

Meaning

Control e.g. light point

Change home profile between ‘HOME’ and ‘AWAY’

Change room profiles

If you have defined a group of target controls, you can switch them off / on.

You can set dimmers up / down

You can define level of ventilation if a unit is connected to the system

For the lever switches you can define same functionality except dimmer adjustment or

Ventilation level.

8. Setting security system

From ‘SETTINGS’ – ‘SECURITY SYSTEM’ you can control how system behaves on different alarm states.

From ‘PROFILE SETTINGS’ you can define what is the state of profile (HOME/AWAY/…) when system is ‘DIS ARMED’ (deactivated) or ‘ARMED’ (activated).

From ‘DELAYS’ can be defined how long system is in standby before changed. ‘ENTRY DELAY’ when coming in and ‘EXIT DELAY’ when leaving the house.

From ‘ALARMS’ section you can define what alarm outputs activates on different alarm sources.

Under ‘SECURITY SERVICE PROVIDER’ you can define the SMS number of security company & what alarms they will get.

From ‘SECURITY DEVICES’ you can define functions shown on table 11.

Table 11. Functions for security devices.

Function

Inhibit

Part of shell protection

Part of entry route

Part of exit route

Meaning

This security device is not used

This device is part of shell protection and does not cause alarm. E.g. indoor motion detector

This device uses delay before alarm. E.g. Front door switch

This device uses delay before alarm. E.g. Front door switch

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

16/23

From ‘SETTINGS’ – ‘SECURITY SETTINGS’ – ‘ALARM RULES’ you can define what is the state of the control device on different alarm states similar way like on room profiles. Different alarms are listed on table 12.

Table 12. Alarm sources.

Alarm type

Burglary alarm

Carbon monoxide alarm

Device alarm

Fire alarm

Tamper alarm

Water leakage

9. Contact information

Home pages: www.smarthome.eke.com/es/

Source

Launched by motion detectors, door contacts etc.

Detected by CO sensor

E.g. malfunction of circuit breaker

Fire detector

Sabotage switch is activated on some device

Sensor has detected water

Email: [email protected]

Copyright © EKE Group. All Rights Reserved

APPENDIX I: Circuit diagrams

200091-A

2015-08-01

17/23

Connection of KPD-100 to SCU-100. Connection of KPD-100 to CPU-140

Connection of KPD-140 to SCU-100 Connection of KPD-140 to CPU-140

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

18/23

Connection of glass brake detector to SCU-100 Connection of motion detector to SCU-100

Connection of panic button to SCU-100

Connection of door contact to SCU-100

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

19/23

Connection of water leak detector to SCU-100

Connection of CO detector to SCU-100

Connection of Fire detector to SCU-100 Connection of 3-phase electricity break detection to SCU-100

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

20/23

Connection of siren to SCU-100

Connection of SEN-140/141 temperature / light level and humidity measurement to MSU-

140/CPU-140

Connection of M21R/M21B siren to SCU-100

Connection of SEN-OUT Outdoor temperature and light level sensor to MSU-140/CPU-140

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

21/23

Connection of current clamp to MSU-140/CPU-

140

Connection of push buttons to CTU-100

Connection of S0 pulse output energy meter to

MSU-140/CPU-140

Connection of intermediate relays to CTU-100

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

22/23

Connection of LR24 valve motor to CTU-

100/ADU-140

Alternative way to connect dimmer with multiple loads so that it dims same time all the loads.

Connection of Hager EV100 dimmer to ADU-140

Connection of Eltako LUD+SUD dimmer to ADU-

140

Copyright © EKE Group. All Rights Reserved

200091-A

2015-08-01

23/23

Connection of radiator valve to CTU-100/ADU-

140

Copyright © EKE Group. All Rights Reserved

advertisement

Key Features

  • Easy installation and configuration
  • Connects to various devices
  • Customizable security settings
  • Room profile modes
  • Mobile app control
  • Alarm notifications
  • User interface language selection
  • System diagnostics
  • Backup and restore settings
  • Network settings and camera integration

Frequently Answers and Questions

How do I connect the system to my electrical cabinet?
Refer to the 'product cards' on the system parts and dimensions. Make sure the system is installed in a dry place and keep it separate from AC 230V parts.
What does 'AAC' stand for in the CPU's diagnostic values?
'AAC' stands for 'Attached Accessory Count' and informs how many modules are detected by the system.
How do I define functions for push buttons?
Go to 'CONTROL' - 'BUTTON' page and press the button you want to configure. You can define functions like controlling light points, changing profiles, adjusting dimmers, etc.
How do I set up the security system?
From 'SETTINGS' - 'SECURITY SYSTEM' you can control how the system behaves on different alarm states. You can define profiles, delays, alarm outputs, and security device functions.

Related manuals

Download PDF

advertisement