Fig. 2
•
•
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
•
•
SL6USBC / SL6USBW
SAFETY
•
•
•
•
•
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
Please isolate mains prior to installation or maintenance
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse or circuit breaker
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
This product is Class II double insulated
This product series is IP20 rated
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the manufacturer of the sensors that they are compatible with LED luminaires
Provide power to the required point of installation
Remove the diffuser by gently squeezing inwards top and bottom at both ends then pull away from the luminaire, see Fig. 1
Fig. 1
•
Remove the LED tube by pushing it at one end and gently pulling out of the lamp holders
Using the luminaire as a template, mark the location for, and drill the fixing holes ensuring not to infringe with any gas / water pipes or electrical cables
Remove the two screws at the rear of the fitting and remove the access plate to expose the terminal block, see Fig. 2
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
•
•
SL6USBC / SL6USBW
SAFETY
•
•
•
•
•
•
This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
Please isolate mains prior to installation or maintenance
Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse or circuit breaker
Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
This product is Class II double insulated
This product series is IP20 rated
INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please confirm with the manufacturer of the sensors that they are compatible with LED luminaires
Provide power to the required point of installation
Remove the diffuser by gently squeezing inwards top and bottom at both ends then pull away from the luminaire, see Fig. 1
Fig. 1
•
•
•
Remove the LED tube by pushing it at one end and gently pulling out of the lamp holders
Using the luminaire as a template, mark the location for, and drill the fixing holes ensuring not to infringe with any gas / water pipes or electrical cables
Remove the two screws at the rear of the fitting and remove the access plate to expose the terminal block, see Fig. 2
•
Fig. 3
Fig. 2
Ensuring correct polarity is observed, carefully wire as shown in Fig. 3
•
•
•
•
Re-fit the access plate
Align the luminaire with the previously drilled holes and attach to the surface
Insert the LED lamp and re-fit the diffuser
Switch on and check for correct operation
Note – The pullcord is for light operation only. Shaver and USB Charger remain permanently live
WARNING
This luminaire must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the product.
This product is non-dimmable.
WARRANTY
This product has a warranty of 2 years from date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior notice.
AVAPR20_V1
