installation manual

Operating and Maintenance Instructions
Mira LED Exam Light
Ceiling Mount
w w w . a m i c o . c o m
Contents
Introduction3
Symbols Used in This Manual 4
Safety Instructions
5-7
Scope of Delivery
8
Installing Ceiling Mount
9-11
Installing Ceiling Arm
12
Installing The Lighthead
13
Operation14
Disinfecting, Cleaning and Sterilization
15
Maintenance16
Notes On The Arm Systems
17-18
Spare Parts
19
Disassembly20
Technical Data of the Lighthead
21
Technical Data of the Arm System
22
Warranty23
2
Amico Lights Corporation
Introduction
Thank you for your purchase of the Mira LED Minor Surgery Light.
This installation manual gives you instructions on how to install the Mira LED Light for a Wall Mounted, Ceiling
Mounted or Floorstand version of your purchase. For instructions on operation, maintenance and further description
of the product please refer to the Operation and Maintenance Manual included.
Please read the following instructions very carefully and follow the safety instructions and requirements.
www.amico.com
3
Symbols
Used in This Manual
1
SYMBOLS
1
SYMBOLS
1The
SYMBOLS
warning
symbols indicate
indicate all
all instructions
instructions that
that are
are important
important for
for safety.
safety. Failure
Failure to
to comply
comply with
with them
them can
can lead
lead to
to injury,
injury,
symbols
1The warning
SYMBOLS
damagesymbols
to the
the luminaire
luminaire
or all
theinstructions
equipment. In
Inthat
combination
with the
thefor
following
signal
words
the warning
warning
symbols
means:
damage
to
or
the
equipment.
combination
with
following
words
the
symbols
means:
The warning
indicate
are important
safety.signal
Failure
to comply
with
them can
lead
ENG
SYMBOLS
ENG
SYMBOLS
Thedamage
warning to
symbols
indicate allorinstructions
that are In
important
for safety.
Failure
to comply with
them
can lead
towarning
injury,
to injury,
the
luminaire
the
equipment.
combination
with
the
following
signal
words
the
The
warning
symbols
indicate
all
instructions
that
are
important
for
safety.
Failure
to
comply
with
them
can
lead
to
injury,
DANGER
DANGER
damage to the
luminaire or the equipment. In combination with the following signal words the warning symbols means:
to the
luminaire
the or
equipment.
In combination with the following signal words the warning symbols means:
symbols
means:
Can
lead to
to or
death
serious injury.
injury.
1damage
SYMBOLS
Can
lead
death
or serious
1
SYMBOLS
DANGER
DANGER
Can lead to death or serious injury.
Can
lead to death or serious injury.
WARNING
WARNING
ENG
SYMBOLS
ENG
SYMBOLS
The
warningCan
symbol
or
Can
leadisto
toused
injuryfor all instructions that are important for safety. If warnings are ignored, users may be injured
DANGER
lead
injury
The
warning
symbol
is used
for
all
instructions
that
are important
for
safety.
Ifthe
warnings
aresignal
ignored,
users
may
be injured or
the light
or surroundings
may
be
damaged.
The
warning
symbol
is
used
with
following
words
as
follows:
WARNING
the light or surroundings
may
damaged. The warning symbol is used with the following signal words as follows:
WARNING
Can lead
to be
injury.
1
SYMBOLS
Can
leadwith
to injury
1 WARNING
SYMBOLS
Comply
operating
instructions
WARNING
Can leadwith
to injury
Comply
operating instructions
WARNING
Can lead to death or serious injury.
May cause
death
or operating
serious injury.
Comply
with
instructions
May
cause
death
or serious
injury.
Comply
with
operating
instructions
Comply with operating instructions
The
warningCE
symbol
is used
used
for all
all instructions
instructions that
that are
are important
conformity
mark
The warning
symbol
is
for
important for
for safety.
safety. If
If warnings
warnings are
are ignored,
ignored, users
users may
may be
be injured
injured or
or
CE
conformity
mark
CAUTION
the
may
the light
light or
or surroundings
surroundings
may be
be damaged.
damaged. The
The warning
warning symbol
symbol is
is used
used with
with the
the following
following signal
signal words
words as
as follows:
follows:
CAUTION
CE conformity
mark
May cause
minor injury.
CE conformity
mark
May
cause minor
injury.
WARNING
CE conformity mark
WARNING
May
cause
death
or
Protective
conductor
May
cause
death conductor
or serious
serious injury.
injury.
Protective
conductor
Protective
earth
Protective
Protective earth
Protective conductor
Protective conductor
CAUTION
Neutral
conductor/return
conductor
for the
the electrical
electrical
current current
CAUTION
Neutral
conductor/return
conductor
for the electrical
Neutral
conductor/return
conductor
for
current
Neutral
conductor
return line
for current
May
minor
Neutral
conductor
return line for current
May cause
cause
minor injury.
injury.
Neutral
conductor/return
for the electrical current
Live
conductor conductor
Liveconductor
conductor
Neutral
conductor/return
conductor for the electrical current
Live
conductor
Live
Protective
earth
Live
conductor
Protective
earth
Storage humidity
Live conductor
Live conductor
Storage humidity
humidity
Storage
Disposal
Neutral
Disposal
Neutral conductor
conductor return
return line
line for
for current
current
Storage
humidity
Storage
temperature
Storage
humidity
Live
conductor
Storage
temperature
Live
conductor
Storage
temperature
Manufacturer
Manufacturer
Storage
temperature
Disposal
Storage temperature
Disposal
Disposal
Disposal
Disposal
Manufacturer
Disposal
Disposal
Manufacturer
Manufacturer
Manufacturer
Manufacturer
Manufacturer
Manufacturer
Trademarks: All trade names mentioned in these instructions are the exclusive property of the relevant manufacturers.
Publication Revision: 02/17/13
Trademarks: All
All trade
trade names
names mentioned
mentioned in
in these
these instructions
instructions are
are the
the exclusive
exclusive property
property of
of the
the relevant
relevant manufacturers.
manufacturers.
Trademarks:
Publication Revision:
Revision: 02/17/13
02/17/13
Publication
Trademarks:
All trade names mentioned in these instructions are the exclusive property of the relevant manufacturers.
Trademarks: All trade names mentioned in these instructions are the exclusive property of the relevant manufacturers.
Publication Revision: 02/17/13
Publication Revision: 02/17/13
4
Amico Lights Corporation
Safety Instructions
Intended use
The Mira LED Minor Surgery Light is intended to provide illumination for minor surgery, diagnosis, or examination. It
is to be used near the patient to support treatments, which pose no risk to the patient in the event of any interruption
caused by light failure. It is meant for continuous operation.
User profiles
Medical staff
All persons with medical training who work in the field for which they were trained.
Cleaning staff
All persons familiar with national and workplace hygiene requirements.
Electricians
All persons with training in electronics and electrical technology who are familiar with the relevant standards and
regulations.
Certified installers
Persons qualified by training, experience and knowledge of the regulations to install and remove the equipment.
Safety Instructions
Please note that certain duties must be carried out by people with the appropriate corresponding qualifications. The
instructions are part of the product and must be kept so they are accessible for all subsequent users:
• These instructions are for the Amico Lights Mira Series LED lights. This includes ceiling, floorstand and wall
mounted equipment.
• Please carefully read these operating instructions before using the equipment. It will help protect you and
others from potential injuries that may occur.
• All work on the light (including repairs) must be done by qualified electricians only. The light must be installed
by a certified installer.
• The light must not be modified or manipulated. Use in any other manner than with the original parts may
result in different specifications and life-threatening dangers.
• Only persons with medical training are permitted to operate the equipment.
• Only trained cleaning personnel are permitted to clean the equipment.
• The light must not be used in an explosive environment. The power supply to the light is a potential ignition
source.
• The light must be used in dry rooms only.
• The light must not be left on unattended.
• Keep all flammable equipment and objects away from the Lighthead and cone during use.
• Do not use a damaged light. Defective cables can also be a potential hazard. Do not position cables near heat
sources or sharp edges.
• Eye damage. Never look directly at the light cone.
• Replace damaged lenses before using the light again.
• The light must be connected to the mains with a protective earth to prevent electric shock.
www.amico.com
5
Safety Instructions
• Never apply additional loads to the Lighthead and spring arm.
• Do not cover the light with a cloth or similar material while operating.
• If problems are encountered that have not been addressed in these operating instructions, please contact
your supplier in the interest of your own safety.
Please keep these operating instructions in a secured place near the device. This ensures easy access to safety
instructions and important information should the need arise.
• The inspections and maintenance work, as described on page 30, should only be done by trained service
technicians. Anyone else is not authorized to perform inspections and maintenance work.
• The adjustment work should only be carried out by a hospital technician or someone with similar
qualifications. Anyone else is not authorized to perform adjustment work.
• This equipment has been built accordingly and is operationally safe. Nonetheless, it may still present some
danger, especially if not used according to the operating instructions as specified in this manual.
• Modifications are never to be made for any reason. This is to ensure safety for all persons involved. Any
modifications made to the system void the warranty.
• The contents of the operating instructions are subjected to change without notice.
Specific fitting instructions
Mira LED Ceiling Mount
• Mounting material not included in delivery.
• The ceiling mount may be fitted to ceiling only with a concrete strength of B25 (C20/25) or greater.
• Contact with reinforcing elements of the solid slab ceiling must be avoided. In case of doubt, a structural
engineer should control the mounting on the respective surface.
• The drill holes should be made by a skilled person in accordance with the drill hole tolerances recommended
by the manufacturer of the fastening anchors.
• The screws must be carefully tightened using a torque wrench in accordance with the recommendations of
the manufacturer of the fastening anchors.
Mira LED Wall Mount
• Mounting Material not included in delivery.
The light may be mounted only on walls that guarantee sufficient hold. The necessary technical information can be
found in the installation section of this manual.
6
Amico Lights Corporation


operating
instructions
as to
specified
in this
manual.
Modifications
are never
be made
for any
reason.
Modifications
are safety
never for
to be
made forinvolved.
any reason.
This
is to ensure
all persons
Any
This is to ensure
safety
forsystem
all persons
involved.
Any
modifications
made
to the
void the
warranty.
modifications
system void
the warranty.
The
contentsmade
of to
thetheoperating
instructions
are
The contents
of the
operating
subjected
to change
without
notice. instructions are
subjected to change without notice.
Safety Instructions


2.4
2.4
Warning levels
Warning levels
Warning
levels
DANGER
DANGER
Indication of hazards that can lead to death or serious
injury
if measures
arethat
disregarded.
DANGER
Indication
of hazards
can lead to death or serious
injury if measures
are disregarded.
Indication
of hazards
that can lead to death or serious injury if measures are disregarded.
WARNING
WARNING
Indication of hazards that can lead to injury if measures
WARNING
are
disregarded.
Indication
of hazards that can lead to injury if measures
Indication
of hazards that can lead to injury if measures are disregarded.
are disregarded.
CAUTION
CAUTION
Indication
of hazards that can lead to damage to
CAUTION
property
if of
measures
disregarded.
Indication
hazardsare
that
can lead
leadtotodamage
damagetoto
Indication of
hazards
that
can
property if measures are disregarded.
property if measures are disregarded.
EXPLOSION HAZARD
EXPLOSION HAZARD
EXPLOSION
HAZARD
The above is an explosion hazard warning symbol. NonThe
above
is
an
explosion
hazard
warning symbol.
Non-compliance with this symbol may result in damages or injuries
The above iswith
an explosion
hazard
Noncompliance
this symbol
may warning
result insymbol.
damages
or
due
to explosion.
compliance
with
this symbol may result in damages or
injuries
due to
explosion.
injuries due to explosion.
ELECTRIC SHOCK
SHOCK
ELECTRIC
ELECTRIC
SHOCK
The above
is an electric
shock warning symbol. Non-compliance with this symbol may result in damages or injuries
The above is an electric shock warning symbol. Nondue
to electric shock.
The above is an electric shock warning symbol. Noncompliance with this symbol may result in damages or
compliance
with
this symbol
injuries
due to
electric
shock. may result in damages or
injuries due to electric shock.
4
4
www.amico.com
7
Scope of Delivery
Ceiling Mount
Included:
8
1x Lighthead with sterilizable handle
1x ceiling mount (may not be exactly as shown)
1x ceiling arm
1x dome cover
1x ceiling tube
1x ring
Amico Lights Corporation
Installing Ceiling Mount
Load data
Bending moment MBmax. 210 Nm
Vertical weight forces FG
max. 205 N
• 1x load only. Regional safety factors to be considered.
• Maximum device load is assumed and included.
Installing ceiling mount
DANGER
Mounting by qualified personnel
• Mounting must be done by qualified personnel only. Lack of appropriate knowledge could be life-threatening.
DANGER
Life-threatening danger from falling luminaire.
• The ceiling must be made of solid concrete to guarantee a secure hold.
DANGER
Electric shocks are life-threatening.
• The electrical mains must be isolated from the by an external all-pole switch.
2
1
2
1
1. Loosen the mounting screw from the receptacle.
4. Remove the cotter pins (1) and mounting pins (2).
2
3
1
2. Using long-nose pliers, pull the receptacle with cable
completely out of the ceiling tube at the inner ring.
5. Insert the ceiling tube (1) into the ceiling mounting
(2) and drill with an Ø 10.5 mm bit (3). Use the existing
bores of the ceiling mounting as a guide.
3. Cut the ceiling tube to the required length at the
upper end using a metal saw and deburr the cut end.
6. Push the cable with receptacle into the ceiling tube
again.
www.amico.com
9
Installing Ceiling Mount
135
270
7. Align the threaded bore in the receptacle exactly
with the existing bore in the ceiling tube. Fix with the
mounting screw.
8. Secure the ceiling mount to the ceiling using the
mounting holes provided, and the load data listed in
on the previous page. Ensure 25 mm of clearance is
present above the ceiling mount.
DANGER
Risk of injury from falling parts.
• The ceiling bearing must be secured to the fastening material, that must be suitable for the corresponding
ceiling condition.
DANGER
Risk of injury from falling parts.
• Mounting must be performed by two people.
CAUTION
Use protective equipment in line with tool manufacturer’s instructions.
2
2
1
1
9. Pull the lamp cable from the ceiling tube through the
mounting. Insert the ceiling tube into the mounting.
Secure with the two mounting pins (1) and two cotter
pins (2).
1
10. Tighten the four Allen screws in the mounting (1).
DANGER
Mortal danger from electric shock.
• Disconnect or remove fuses before carrying out any work on the mains connection
• The systems must be wired by a qualified electrician or someone with similar qualifications.
10
Amico Lights Corporation
the light or surroundings may be damaged. The warning symbol is used with the following signal words as follows:
WARNING
WARNING
May cause death or serious injury.
May cause death or serious injury.
Installing CeilingCAUTION
Mount
CAUTION
May cause minor injury.
May cause minor injury.
Protective earth
Protective earth
Neutral conductor return line for current
Neutral conductor return line for current
Live conductor
Live conductor
11. Connect to the main power supply.
Disposal
Disposal
1
13. Slide cover and ring over ceiling mount and tighten
ring screws (1).
Manufacturer
Manufacturer
12. Connect the ceiling tube cable to the power harness
(if power harnesses are installed).
4
4
www.amico.com
11
Installing Ceiling Arm
WARNING
Danger of injury from unfolding spring arm.
4
1
2
3
1. Gently pry the two halves of the cover apart and set
aside.
4. First install washer (1), then safety washer (2), followed
by two locking rings (3). Ensure tooth on safety
washer aligns with the hole in the ceiling tube (4).
1
2
2
1
1
2
2. Remove two screws (1) from receptacle mount. Move
receptacle mount (2) to provide access for mounting.
5. Replace the receptacle mount (1). Reinstall two screws
(2), do not over tighten.
3. Install ceiling arm.
6. Gently replace covers and snap together
WARNING
Device may fall if inaccurately fastened.
• Locking rings must click into groove and be
evenly positioned all around.
7. To continue with installing the Lighthead see
Installing the Lighthead section of this manual
12
Amico Lights Corporation
Installing The Lighthead
1. Remove screw
4. Insert safety segment.
2. Rotate sleeve so the notch and slot are aligned.
5. Turn back sleeve and install the screw. Tighten screw
according to requirements of the friction from the
Lighthead.
3. Insert Lighthead.
6. Clip handle on.
CAUTION
Damage can be caused by falling Lighthead.
• Danger of injury through incorrect fitting of the Lighthead.
www.amico.com
13
Operation
Mira LED Floorstand
WARNING
Danger of death from electric shock
• Do not plug in a damaged power cable
• Replace damaged power cable before using light again
• The mains voltage and frequency must match the data on the name plate
• Connect to a mains connection with a protective earth only.
NOTICE:
• Wind the power cable to the cable retainers when it is not being used.
2
1
1. Plug in cable (1).
2. Install the cable to the mains supply.
3. Switch on (2).
Mira LED – All Models
Switch on Light from control pad at Lighthead.
Power (on/off )
Decrease brightness
14
Amico Lights Corporation
Endo Light (on/off )
Increase brightness
Disinfecting, Cleaning and Sterilization
NOTICE:
Damage due to improper cleaning
• Do not use alcohol, solvent or cleaning agents containing chlorine or scouring agents.
• Damage to lens by concentrated disinfectant or solvent.
• Follow the manufacturers recommended mixing ratio.
• Use of incorrect cloths may scratch lens.
NOTICE
A dirty lens will reduce the illuminating power.
• Clean lens regularly
• Spray and wipe disinfection is permitted.
• Clean the lens with a leather cloth soaked in cleaner
• Spray disinfectant in horizontal position.
NOTICE
The external components of the light can be disinfected with the following diluted products:
• Lysoformin
• Dismozon
• Hexaquart plus
• Sagrotan – fast disinfecting cleaner
NOTICE
The local government regulations for disinfection must also be observed in addition to these instructions.
NOTICE
Sterilize handle at 120⁰C and 1.05 bar for 30 minutes.
www.amico.com
15
Maintenance
DANGER
Electric shocks are life-threatening.
• Remove the connector from the power supply and put the switch in the “OFF” position.
• The connector cable must be checked for damage at least once per year.
NOTE
• Maintenance and repairs must only be carried out by qualified electricians.
• The corresponding user profile is described in Chapter 2, Safety instructions
Setting Spring Force
NOTE
The spring force is set at the optimum setting in the factory
• Lift the spring arm to its highest position.
• Insert a 6 mm Allen key through window and turn
the adjustment screw.
Setting spring force:
• Turn screw counter clockwise (+) to increase spring force (when spring arm lowers)
• Turn screw clockwise (-) to decrease spring force (when spring arm rises)
16
Amico Lights Corporation
Notes On The Arm Systems
Selection Of Fastening Material
We recommend the use of (not included in the delivery) counter-plates for fastening to drywall.
Cleaning and disinfection
DANGER
Electric shocks are life-threatening.
• The devices can conduct electricity and must be handled with care during cleaning and disinfection.
• If there is a power plug remove it from the socket.
• Do not use spraying methods for cleaning and/or disinfection.
• Do not spray liquid into the openings of electrical power sockets, gas sockets or devices, or allow liquid to
enter these.
Recommended cleaning agents
Use mild soap solutions or standard detergents as cleaning agents. Wipe down the surfaces of the equipment with
a dampened cloth. If necessary, use small quantities of mild soap solution as a cleaning agent. Then wipe the outer
surfaces with a soft, clean cloth until they are completely dry.
Disinfection procedure
Disinfection by wiping is intended to be the standard disinfection procedure for the support arm system. Hygiene
guidelines and corresponding safety measures must be determined by the operator for the disinfection procedures
that are applied.
• After the contamination by any potentially infectious material (such as blood, secretions or excrement), the
areas must be disinfected immediately in a targeted way.
• Comply with application concentrations.
• Wipe the area to be disinfected rather than spraying it.
• Do not use areas that have been wiped until the disinfectant is dry.
•
Testing
DANGER
Electric shocks are life-threatening.
• During all testing work, disconnect the device from the power supply/remove the plug from the power socket
and secure the device so that it cannot be switched on again.
Every 6 months or 5000 arm movements check for:
• Paint damage
• Cracks in plastic parts
• Deformation of the support system
• Loosening of parts
Every 2 years:
The securing element of the cantilever arm must be checked and greased by a qualified professional.
www.amico.com
17
Notes On The Arm Systems
Disassembling For Servicing
DANGER
Injury hazard
• The cantilever arm is under a high spring load. If the end device is not moved to the upper cantilever arm
position, the cantilever arm will spring up, possibly causing serious injury. Only remove the end device if the
cantilever arm is in the upper position.
• Disconnect the device from the power supply/remove the plug from the mains and ensure it cannot be
switched on again.
• Place cantilever arm in the upper position.
• Unscrew the brake screw 1 so that the sleeve 2 can be turned.
• Turn the sleeve 2 through 180 degrees until the securing segment 3 appears in the slot 4.
• Hold the end device head 5 firmly and remove the securing segment 3 using a narrow flat-bladed screwdriver.
• Remove end device 5 from the connection.
• Put protective cap in place.
1. Brake screw
2. Sleeve
3. Securing segment
4. Slot
5. End device terminal
This system is designed to be equipped with end devices from other manufacturers. For end device operation
instructions please refer to the operating instructions of the related manufacturer.
18
Amico Lights Corporation
al
WARNING
ENG
Never unscrew the top cable retainer.
Spare Parts

Handle (Art.- Nr. D51.040.000)
If both cable retainers are unscrewed, the
connection will be loose and will fall, which
may cause
injury and
damage to the cables
13
SPARE
PARTS
and lamp.
Rotary knob (Art.- Nr. D51.050.000)
ENG
dispose of the light with the
12.113 Disposal
SPARE PARTS
fuse. Dispose oft he light at a
centre or return it to a dealer
not dispose of
sposal serviceDodebending
onthe light with the
normal refuse. Dispose oft he light at a
ulations. Cut offrecycling
the cable
centreflush
or return it to a dealer
ousing.HandleHandle
with
a
disposal
service debending on
(Art.Nr.
D51.040.000)
(Art.- Nr. D51.040.000)
Rotary knob (Art.- Nr. D51.050.000)
Cable:
Cable:
• Cable:
Schuko D70.017.000
 Schuko
D70.017.000
• CH Schuko
D70.018.000
 CH
D70.018.000
D70.017.000
 CH
D70.018.000
 UK
D70.019.000
• UK D70.019.000
UK
D70.019.000
 US
D70.020.000
US HG
D70.020.000
• USHG
HG
D70.020.000
local regulations. Cut off the cable flush
with the housing.
Handle (Art.- Nr. D51.040.000)
Rotary knob (Art.- Nr. D51.050.000)
Fast-blow 1A fuse (Art.- Nr. D69.596.000)
Rotary knob (Art.- Nr. D51.050.000)
• triango
Fast-blow
30 F 1A
onlyfuse (Art.- Nr. D69.596.000) Mira LED
Floorstand only
Rotary knob (Art.- Nr. D51.050.000)
Cable:
Schuko
CH
UK
US HG




Fast-blow 1A fuse (Art.- Nr. D69.596.000)
triango 30 F only
D70.017.000
D70.018.000
D70.019.000
D70.020.000
Troubleshooting
Cable:
 Schuko
 CH
 UK
 US HG
D70.017.000
D70.018.000
D70.019.000
D70.020.000
Fast-blow
1A fuse (Art.- Nr. D69.596.000)
Malfunction
Possible
triango 30 F only
cause
Remedy
User profiles
Light does not come on
Contact fault
Switch on again
All
Light does not come on
Illuminant defective
Contact manufacturer’s AfterSales Service
Only by manufacturer’s AfterSales Service
Check power supply and all
connections
Qualified electrician
Replace fuse
Qualified electrician
Fast-blow 1A fuse (Art.- Nr. D69.596.000)
Light
does30
not
come on
triango
F only
Light does not come on
No mains power
1A fuse defective
(Mira LED Floorstand only)
19
www.amico.com
19
19
19
The warning symbol is used for all instructions that are important for safety. If warnings are ignored, users may be injured or
the light or surroundings may be damaged. The warning symbol is used with the following signal words as follows:
Disassembly
WARNING
May cause death or serious injury.
CAUTION
DANGER
May cause
injury.
Electric shocks
are minor
life-threatening.
• Remove connector from the power supply and put the switch in the “OFF” position before disassembling. Protective earth
DANGER
Never unscrew the upper cable holder - injury hazard.
Neutral conductor return line for current
• When both cable holders are unscrewed, the connecting piece is loose and falls downward, which could cause
injury and/or damage to the cable and/or the device
Live conductor
Disposal
Disposal
Do not dispose of this product with normal refuse. Dispose of the product at a recycling center or return it to
a dealer with a disposal service depending on local regulations. Cut off the cable flush with the housing.
Manufacturer
4
20
Amico Lights Corporation
Technical Data of the Lighthead
Units
Lighthead Diameter
Mira 50 LED
Mira 65 LED
Mira 90 LED
in
18
18
18
lx (fc)
50,000 Lux (4,762 fc)
@ 1m (39.37")
65,000 Lux (6,190 fc)
@ 1m (39.37")
90,000 Lux (8,571 fc)
@ 1m (39.37")
Brightness Control
%
50-100
50-100
50-100
Light Field Diameter
in
6.5-12.0
6.5-12.0
6.5-12.0
Depth of Illumination
in
94.5
94.5
94.5
Color Rendering Index
Ra
95
95
95
R9
in
90
90
90
Weight of Lighthead
lbs
11
11
11
K
4500
4500
4500
Single Mask
%
0.7
0.7
0.7
Double Mask
%
55.5
55.5
55.5
Cavity
%
100
100
100
Single Mask with Cavity
%
0.3
0.3
0.3
Double Mask with Cavity
%
55.3
55.3
55.3
36
36
36
Light Intensity (Central Luminance)
Color Temperature (Standard)
Shadow Dilution
Number of LED's (Main)
LED Service Life
hours
50,000
50,000
50,000
Total Radiant Power at Max Intensity
W/m²
178
231.4
317
100-240 VAC, 50/60 Hz,
0.40 amps
100-240 VAC, 50/60 Hz,
0.55 amps
100-240 VAC, 50/60 Hz,
0.65 amps
Direct Power Supply
Direct Power Supply
Direct Power Supply
Mounting Options
Ceiling, Wall, Floorstand
Ceiling, Wall, Floorstand
Ceiling, Wall, Floorstand
Certificates
cETLus conform to
UL60601-1; UL60601-2-41;
UL certified IP54 per
IEC 60598
cETLus conform to
UL60601-1; UL60601-2-41;
UL certified IP54 per
IEC 60598
cETLus conform to
UL60601-1; UL60601-2-41;
UL certified IP54 per
IEC 60598
Electrical
Power Supply
ea
www.amico.com
21
Technical Data of the Arm System
Electrical:
Nominal input voltage100-240 VAC
Frequency range 50 / 60Hz
Input current4A-2A
Device ProtectionClass 1 Approval ETL/cETL
Environmental conditions for transport, storage and operation:
Storage and transport
After 15 weeks the conditions for operation apply.
-10°C to +50°C Ambient
20% to 90% humidity
700hPa to 1060hPa
Operation
This product should be acclimatized to its operating conditions for 24 hours prior to its first use.
+10°C to +40°C
30% to 75% humidity
Weight:
Maximum device load42Nm (375 in-lb)
Mira LED Swing Floor Stand 11 kg (24 lbs)
Mira LED Swing Ceiling Mount
10 kg (22 lbs)
Operating mode:
Operating modecontinuous operation
Classification:
Mira LED SwingClass I
Classification under 93/42 EEC – Annex IX
Class I
(medical device class)
Safety testing according to: CSA C22.2#60601-1 IEC/EN 60601-1 2nd. UL 60601-1
22
Amico Lights Corporation
Warranty Policy - Lighting Products
Amico Lights Corporation is warranted against defective materials and workmanship for twelve (12) months from the date of
shipment. Within this period, Amico Lights Corporation will repair or replace any part on site or at the factory which is proven to
be defective at Amico Lights Corporation cost.
Furthermore, Amico Lights Corporation will warrant its material to be free from defect for an additional period of four (4) years
(five [5] years from the date of shipment). Within this period, Amico Lights Corporation will replace any part which is proven to
be defective, at no charge. Shipping and installation costs after the first twelve (12) months will be borne by the Customer.
The Warranty applies to normal usage and does not apply to any product that has been subject to alteration, abuse, negligence
or use (including voltage and/or current) other than that for which the product was designed.
Amico Lights Corporation shall not be liable for incidental or consequential damages resulting from the use of the equipment.
All claims for warranty must first be approved by Amico Lights Corporation. A valid Return Goods Authorization (RGA) number
must be obtained from Amico Lights Corporation prior to commencement of any service work. Warranty work, which has not
been pre-authorized by Amico Lights Corporation, will not be reimbursed.
Amico Lights Corporation 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada
71 East Industry Court, Deer Park, NY 11729, USA
Tel: 905.764.0800 | Fax: 905.764.0862
www.amico.com
www.amico.com
23
www.amico.com
Amico Lights Corporation | www.amico.com
85 Fulton Way, Richmond Hill
Ontario, L4B 2N4, Canada
Toll Free Tel: 1.877.264.2697
Toll Free Fax: 1.866.440.4986
Tel: 905.763.7778
Fax: 905.763.8587
Email: [email protected]
LT-INSTALL-INSTR-MIRA-LED-CLNG 11.26.2015

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project