USER MANUAL
CONGRATULATIONS
ON PURCHASING
YOUR TOTALLY WICKED
ARC PALM ELECTRONIC
CIGARETTE KIT
Power
button
Tank
Battery
Atomizer
head
LED
Tank
base
USING YOUR ARC PALM
Priming the atomizer head
Note: It is important to “prime” a new atomizer head before first
use. Failure to do so can cause the atomizer coil to overheat,
leading to an unpleasant taste and sometimes irreversible damage
to the atomizer head.
Remove the Slider CS Air tank from the arc Palm by unscrewing.
Invert the Slider CS Air tank and unscrew the base. Drip a few
drops of e-liquid on each of the four e-liquid inlets on the side
of the atomizer head, and into its central hole to fully wet the
wicking material.
Filling the tank
Press the button located on the side of the tank and slide in
the direction indicated by the arrow, once opened fill the tank,
leaving an air gap of approximately 2mm above the fluid to avoid
air locks or flooding. Once filled, slide the tank shut and the
button will depress, locking the tank.
Note: After priming a new atomizer head and filling the tank, it is
recommended to wait 5 minutes to ensure the atomizer head is
fully saturated.
Power on and off
Press the power button 5 times quickly to turn the arc Palm on.
To turn the device off, press the power button 5 times.
Power
Button
Vaping
Press and hold the power button as you inhale the vapour.
The LED will illuminate while the power button is held down to
vape.
Battery level indication
Approximately one second after the power button is released, the LED will relight to show
the battery’s approximate remaining charge as detailed in the table below.
Battery Level
100%-60%
59%-30%
29%-10%
9%-0%
LED Colour
Green
Orange
Blue
Red
Charging the battery
To charge the battery, connect the charge lead into the USB
port. The LED on the front of the arc Palm will glow red and
simultaneously flash 5 times in green when the charge lead is
first connected. Once charging, the LED will continue to glow
red until fully charged, at which point it will turn off.
USB
port
Changing the atomizer head
To change the atomizer head in the Slider CS
Air tank, remove the tank from the arc Palm by
unscrewing. Invert the tank and unscrew the
base. Remove the atomizer head from the base by
unscrewing, and insert a new atomizer head. After
fitting a new atomizer head, remember that it will
need priming as described in the section “Priming
the atomizer head”.
Adjustment of airflow:
To adjust the airflow to your personal preference, rotate the airflow control ring located
at the bottom of the tank. The more area exposed behind the slots in the airflow ring, the
more open the air draw will be.
Short circuit protection
If a short circuit occurs before the power
button is pressed, the LED will flash 3
times consecutively. If a short circuit
occurs while the power button is pressed,
the LED will flash 3 times consecutively.
Replacing the atomizer head should allow
normal operation to resume. Follow the
steps outlined in ‘Changing the atomizer
head’.
Atomizer protection
If the power button is held down for
longer than 15 seconds, the device will
stop producing any vapour and the power
LED will flash 10 times. After releasing
the power button normal operation will
resume.
Low voltage protection
If the battery voltage drops below 3.3V,
the LED will flash 20 times and the device
will power off. Charge the device via USB
to power it back on.
Kit contents
1 x arc Palm battery
1 x Slider CS Air tank
1 x CS 1.5ohm atomizer head (fitted)
1 x USB cable
1 x User manual
Spare parts
Specifications:
Dimensions: 122mm x 24.0mm x 18.0mm
Battery capacity: 900mAh
Weight: 63g
Tank capacity: 2ml
Voltage Output: 4.2 – 3.3V
Output modes: Direct output with power
limiting
Filling method: Sliding top fill with
pushbutton catch
Airflow type: bottom adjustable
Tank diameter: 16.5mm
Atomizer Resistance Capability: 0.4ohm
- 3.0ohm
Power Output: Maximum 30 watts
Maximum Filling Nozzle Diameter: 2.8mm
Manufactured in China under the authority
of Pillbox38 UK Ltd, Stancliffe Street,
Blackburn, Lancashire, BB2 2QR.
Tel 01254 692244 www.totallywicked.co.uk
Tel 1(888) 761-9425 www.totallywicked.com
Tel 0941-78447082 www.totallywicked.de
Additional product information
There are no reported medical side effects
with this product. If you believe you
experience a side effect, please contact
the manufacturer.
Product Storage and Battery Precautions
• Store the arc Palm and its accessories
away from children when not in use.
• Ensure the arc Palm is powered off when
not in use.
• Avoid accidentally pressing the arc Palm
power button when not in use.
• Please only use the charging cable
provided.
• Please dispose of dead batteries
in accordance with your country’s
appropriate legislation.
• Do not charge the batteries in a damp
environment.
• Do not use the device when
temperatures are outside the range
-10 - 60°0C.
• Do not charge the battery when
temperatures are outside the range
0 - 45°C.
• Do not attempt to repair a faulty arc
Palm as these are sealed units with no
serviceable parts. Attempted repairs will
void the warranty.
Warranty
The arc Palm components have a 28-day
parts warranty, with the exception of
Atomizer Heads, which are consumable
items and covered by “dead on arrival”
warranty only. The USB cable supplied
has a 12-month warranty. If any parts
are found to be faulty within this time
please contact our customer service
team, whose details are on the back page
of this booklet and we will arrange for a
replacement. We may require the goods to
be returned for further investigation.
">
