Dolby Laboratories FLX-1910 Instruction manual

Dolby Laboratories FLX-1910 Instruction manual
FLX-1910
19” LCD Television
This product contains electrical or electronic materials. The presence of these materials may, if
not disposed of properly, have potential adverse effects on the environment and human health.
Presence of this label on the product means it should not be disposed of as unsorted waste
and must be collected separately. As a consumer, you are responsible for ensuring that this
product is disposed of properly. To find out how to properly dispose of this product, please go
to www.Element Electronics.com and click on “Company“ or call the customer service number
for your country listed in the instruction manual.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. © 1992 -1997 Dolby Laboratories, Inc. All rights reserved.
This TV incorporates High-Definition Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
FCC
Federal Communications
Commission Statement
1. Reorient/Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit which is different from what the receiver is
connected to.
4. Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user authority to operate the
equipment.
1
ENGLISH
This equipment has been tested and found to comply with the limits of a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Warnings and Precautions
Warnings and Precautions
To prevent any injuries, the following safety precautions should be observed in the installation, use,
servicing and maintenance of this equipment.
Before operating this equipment, please read this manual completely, and keep it nearby for future
reference.
This symbol is intended to alert the user to avoid the risk of electric shock.
This equipment must not be disassembled by anyone except qualified service personnel.
WARNING
CAUTION
This symbol is intended to alert the user to the presence of important operating and
maintenance instructions in the literature accompanying the appliance.
To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.
▪
▪
▪
▪
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Use of controls, adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
Important Safety Instructions
This symbol indicates caution points.
This symbol indicates actions that should not be done.
This symbol indicates actions that must be performed.
▪ Do not place the equipment on any uneven or unstable carts, stands, tables, shelves etc.
The equipment may fall, causing serious injury to children or adults and serious damage to
the equipment itself.
▪ Use only a cart or stand recommended by the manufacturer. This equipment and
recommended cart or stand should be handled with care. Quick stops, excessive force, and
uneven surfaces may cause the equipment and cart/stand to overturn.
▪ Do not disable the 3-wire grounding type plug. The grounding pin on the 3-prong plug is an
important feature. Removing the grounding pin will increase the risk of damaging the
equipment.
▪ If you can not fit the plug into the electrical outlet, contact an electrician to install a grounding
outlet.
▪ Always operate this equipment from the type of power source indicated on the rear of the
serial/model plate.
▪ Never overload wall outlets and extensions.
2
Warnings and Precautions
▪ Use and handle the power cord with care. Do not place any heavy objects on the AC
power cord.
▪ Do not touch the power cord and antenna cable during lightning.
▪
Remove the plug from the wall outlet, if the equipment will not be used for a long period
of time.
▪
Do not place, use or handle this equipment near water.
▪
Never expose the equipment to liquid, rain, or moisture.
Seek for service if any of the above is spilled into the equipment.
▪
Do not expose the equipment to extreme temperature or to direct sunlight, as the
equipment may heat up and suffer damage.
▪
Do not install the equipment near any heat sources such as radiators, heat registers,
stoves, or any other apparatus that might produce heat.
▪
Do not attempt to service the equipment yourself.
▪
Opening and removing the covers may expose you to dangerous voltage or other
hazards and may void your warranty. Refer service to qualified personnel.
▪
Do not place or drop any other objects on top.
▪
Do not insert anything into the ventilation holes of your equipment.
Inserting any metal or flammable objects may result to fire or electric shock.
▪
Protect the power cord from being walked on or pinchrd particularly at plugs ,convenience
receptacles, and the point where they exit from the apparatus.
▪
Do not place the equipment on uneven or unstable carts, stands, tables, shelves etc. The
equipment may fall, causing serious injury to children or adults and serious damage to
the equipment itself.
Always place the equipment on the floor or on a surface that is sturdy, level, stable and
strong enough to support the weight of the equipment.
▪
Do not block any ventilating openings. Leave an open space around the equipment.
Never place the equipment :
on a bed, sofa, rug, or any other similar surfaces; too close to drapes/curtains/walls, in a
bookcase, built-in cabinet, or any other similar places that may cause poor ventilation.
▪
Unplug this apparatus during lightning storms or when unused for long periods of time.
▪
Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
▪
Always remove the power cord from the outlet before cleaning the equipment.
▪
Never use liquid or aerosol cleaners on the equipment.
Clean only with a soft dry cloth.
▪
Only use attachments/accessories specified by the manufacturer.
3
ENGLISH
▪ Do not pull the AC power cord. Do not handle the AC power cord with a wet hand.
Warnings and Precautions
Outdoor Antenna Safety Instructions
If an outdoor antenna is connected, follow the precautions below:
▪ An outdoor antenna should not be located in any area where it could come in contact with
overhead power lines, or any other electric light or power circuits.
▪
When installing an outdoor antenna system, extreme caution should be taken to prevent
contact with power lines. Direct contact with power lines may be fatal and should be avoided
at all costs.
Section 810 of National Electrical Code (NEC) provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.
Antenna lead-in wire
Ground clamps
Antenna discharge unit
(NEC section 810-20)
Electric service
equipment
Grounding conductors
(NEC section 810-20)
Ground clamps
Power service grounding
(NEC Art250 part H)
NEC : National Electrical code
EXAMPLE OF OUTDOOR ANTENNA GROUNDING
4
TABLE OF CONTENTS
Warnings and Precautions
Important Safety Instructions ....................................................................................... 2
Antenna Safety Instructions ......................................................................................... 4
Chapter 1 Introducing the LCD TV
Key Features ............................................................................................................... 6
Package Contents ....................................................................................................... 7
Setting Your LCD TV.................................................................................................... 8
Your LCD TV .............................................................................................................. 10
Your Remote Control ................................................................................................. 12
Chapter 2 Installing the LCD TV
Connecting a TV Cable or an Antenna ...................................................................... 14
Connecting an A/V Device with Composite Connector .............................................. 19
Connecting an A/V Device with S-Video Connector .................................................. 20
Connecting an A/V Device with Component(YPbPr) Connector................................ 21
Connecting an AV Equipment with HDMI Connector ................................................. 22
Connecting an AV Equipment with DVI Connector .................................................... 23
Connecting a PC........................................................................................................ 24
Connecting an Audio Receiver or a Dolby Digital 5.1 Sound System........................ 25
Chapter 3 Using The Features
Wide Screen Viewing...................................................................................................................................30
Using the Program Guide ..........................................................................................................................27
Operating the Menu .....................................................................................................................................28
Customizing the VIDEO Settings...........................................................................................................29
Customizing the AUDIO Settings...........................................................................................................32
Customizing the TV Settings....................................................................................................................34
Customizing the SETUP Settings .........................................................................................................36
Using the Program Block Settings ........................................................................................................39
Specifications ........................................................................................................ 44
5
ENGLISH
Federal Communications Commission Statement .......................... 1
Chapter 1 Introducing the LCD TV
Chapter 1
Introducing the LCD TV
Key Features
Various Audio/Video terminals for external equipment connection
▪
▪
▪
▪
▪
▪
▪
▪
1 composite VIDEO input terminal
1 S-VIDEO terminals
1 sets of component Video input terminals
1 VGA/PC AUDIO input terminals
1 HDMI input terminal
1 set of Audio(L/R) output terminals for composite C-VIDEO/S-VIDEO
1 COAXIAL output terminal
1 Headphone terminal
The built-in TV tuner to receive HD ATSC
▪ This function allows the reception of HD broadcasting without the addition of a set top
box.
High Definition Multimedia Interface (HDMI)
▪ High Definition Multimedia Interface (HDMI) is a small, user-friendly interconnect that
can carry up to 5 Gbps of combined video and audio in a single cable. This system
eliminates the cost, complexity and confusion of multiple cables used to connect
current A/V systems.
HDTV Component Video Inputs
▪ Offers the best video quality for DVD(1080i, 720p) and digital set-top-box (1080i, 720p)
connections.
2D Digital Noise Reduction
▪ This function can digitally reduce image noise to provide better picture quality.
Film-Mode Detection
▪ This function can automatically detect content derived from film and adjust the
interlacer’s frame matching to provide a more natural-looking, clearer image of the
moving picture.
6
Chapter 1 Introducing the LCD TV
Package Contents
ENGLISH
Make sure all of the following contents are included.
LCD TV
Remote Control/
AAA Batteries x 2
VIDEO Cable
Component Cable
Power Cord
AUDIO Cable
Warranty Card
User’s Manual
Quick Start Guide
S.MODE
MTS
P. MODE
CAPTION
SLEEP
P.SIZE
MUTE
VOL.
GUIDE
INFO
INPUT
CH.
EXIT
MENU
These items are all you need to set up and operate the LCD TV in its basic configuration.
Make sure all of the above contents are included in the package. If you are missing
any items, please contact the Element Electronics customer service department.
7
Chapter 1 Introducing the LCD TV
Setting Up Your LCD TV
How to install the TV Stand
Follow the instructions below to install the TV stand:
Open the box, and make sure all necessary parts are in the box. The package
contains:
Stand
LCD TV
Cover an even stable surface with a soft cloth. Place the LCD TV unit facedown on the cloth. Fit the stand onto the bottom of the LCD TV unit as shown:
Then push until stand into the LCD TV’s stand socket.
8
Chapter 1 Introducing the LCD TV
How to setup the TV
Connect the AC power cord at the back of the TV and connect the power cord to wall outlet.
Insert the 2 batteries supplied in remote control.
Step1
Slide the back cover up to open the
battery compartment of the remote
control.
Step2
Insert two AAA size batteries.
Make sure to match the (+) and
( - ) ends of the batteries with
the (+) and ( - ) ends indicated
in the battery compartment.
Slide the cover back into place.
Do not use caustic cleaners (porcelain, stainless steel, toilet, or oven cleaner
etc.) on the remote, as it may suffer damage.
Connect other an external AV device (refer to page 19-25).
9
ENGLISH
Use a supplied antenna cable to connect the VHF/UHF signal to the LCD TV’s ANT. terminal
(refer to page 15-18).
Chapter 1 Introducing the LCD TV
Your LCD TV
Front/Left /Right Side View and Controls
Right Side View
Front View
Left Side View
IR
Infrared Receiver
LED
The LED light indicates when the
LCD TV is activated.
VOLUME+/Adjusts the volume up and down.
Selects the main-menu item and change
values for items when in the OSD mode.
CHANNEL▲▼
Scans up and down through channels.
Selects sub-menu item when in the OSD
mode.
MENU
Press once to display the OSD (on screen
display), press again to turn the OSD off.
INPUT
Chooses from different input signal sources.
Turns the LCD TV on and into standby mode.
10
HEADPHONE
Connects to the external
headphone for private listening.
Chapter 1 Introducing the LCD TV
Rear View and Jacks
ENGLISH
S-VIDEO/VIDEO/AUDIO(L/R) IN
Connects to the S-Video/Composite VIDEO and AUDIO
(L/R) output jacks on external video equipment.
YPbPr/AUDIO(L/R) IN
Connects to the DVD player, Digital Set-Top-Box, or
other AV equipment with component(YPbPr) video
and audio output jacks.
HDMI IN
Y
Pb
Pr
VIDEO IN S-VIDEO IN
COAXIAL
VHF/UHF IN
PC/VGA IN
PC AUDIO IN
L
AUDIO IN
R
L
AUDIO IN
R
AC IN
Connects to the AC power cord.
PC/VGA IN/ PC AUDIO IN
Connects the PC, or other AV
equipment with VGA and AUDIO
output jacks.
HDMI IN
Connects the all digital AV equipment with HDMI
connector.HDMI supports enhanced, high-definition
video and two-channel digital audio.
COAXIAL
Connects to the audio jack on the digital/standard 5.1 audio system.
VHF/UHF IN
Connects RF input from VHF/UHF antenna or cable
to receive high/standard definition television.
11
Chapter 1 Introducing the LCD TV
Your Remote Control
Turns the LCD TV on and off.
1
1
22
MTS
Cycles through the multi-channels TV
sound(MTS) options: SAP/MONO/
STEREO
3
S.MODE
Selects sound effect options: Surround/
Live/Dance/Techno/Classic/Soft/Rock/
Pop/Off.
4
P.MODE
Selects picture mode: Vivid/Hi-Bright/
Cinema/Sport/User
P.SIZE
Cycles through Wide mode settings :
NORMAL /FULL/WIDE/ZOOM
CAPTION
Cycles through the Closed Caption:
Anlalog Closed Caption:CC1/CC2/
CC3/CC4/TT1/TT2/TT3/TT4/Off
2
S.MODE
MTS
P. MODE
CAPTION
SLEEP
P.SIZE
3
4
6
5
7
5
8
6
9
10
Digital Closed Caption:Service1/
Service2/Service3/Service4/Service5/
Service6/Off
MUTE
12
11
VOL.
GUIDE
INFO
INPUT
CH.
7
SLEEP
Cycles through the LCD TV sleep timer:
OFF/10/20/30/40/50/60/90/120 mins
8
0-9
Select and switch to a channel by using
0-9 buttons.
EXIT
In HDTV mode, use with 0-9 and
buttons to select a digital channels.
MENU
9
JUMP
Returns to previously selected channel.
10 MUTE
Mutes and restores the audio
11 VOL.+-
Increases and decreases volume.
12 CH.+-
Scans up and down the channels
12
Chapter 2 Installing the LCD TV
S.MODE
MTS
P. MODE
CAPTION
SLEEP
P.SIZE
Input Source
TV(CABLE/AIR)
VIDEO1 (AV)
VIDEO2 (S-VIDEO)
VIDEO3 (YPbPr)
VIDEO4 (HDMI)
COMPUTER(VGA)
MUTE
14 GUIDE
Displays the Program Guide on the
screen. Pressing again to turn GUIDE off.
15 EXIT
Exits the OSD menu.
16 ▲▼►◄
Cycles through OSD options and
selects individual menu items. OK
confirms option settings.
OK
VOL.
13
GUIDE
INPUT
CH.
17 INFO
Pressing repeatedly displays a variety of
information such as the current channel
and the input source.
18 MENU
Displays the OSD menu on the screen.
EXIT
15
14
Pressing INPUT display the source list,
use ▲▼ to select the video equipment
connected to the video inputs of your
LCD TV : TV/HDTV/VIDEO1/VIDEO2/
VIDEO3/VIDEO4/VIDEO5/VIDEO6/
COMPUTER
16
INFO
17
MENU
18
Effective range:
The remote can control the LCD TV from up to 5m away, if pointed directly at the receiver.
13
ENGLISH
13 INPUT
Chapter 2 Installing the LCD TV
Chapter 2
Installing the LCD TV
Refer to the owner’s manual of any external equipment to be connected.
When connecting any external equipment, do not connect any AC power cords to wall outlets
until all other connections are completed.
Connecting a TV Cable or an Antenna
Antenna Connection
The antenna requirements for good color TV reception are more important than those for a black &
white TV reception. For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connection that is provided with the various antenna
systems.
■ A 75-ohm system is generally a round cable (not included) with Ftype connector that can easily be attached to a terminal without
tools.
F-type connector
75-ohm coaxial cable (round)
■ A 300-ohm system is a flat twin-lead cable (not included) that can
be attached to a 75-ohm terminal through a 300-75-ohm adapter
(not included).
300-ohm twin-lead cable (flat)
14
Chapter 2 Installing the LCD TV
Use one of the following two diagrams when connecting an outdoor antenna.
A: Shows how to use a VHF/UHF combination outdoor antenna.
B: Shows how to use a separate VHF and/or UHF outdoor antenna.
ENGLISH
A. Combination VHF/UHF antenna
VHF/UHF
Antenna
300/75-ohm adapter
(not included)
300-ohm twinlead cable
VHF/UHF
Antenna
75-ohm
coaxial cable
B. Separate VHF and/or UHF antennas
UHF
Antenna
Combiner
300-ohm twin(not included)
lead cable
OUT
IN
75-ohm
coaxial cable
300-ohm twinlead cable
15
VHF
Antenna
Chapter 2 Installing the LCD TV
Cable TV (CATV) Connection
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the building
accurately, or as close to the point of cable entry as possible. Use of this TV for other than
private viewing of programs broadcasted on UHF, VHF or transmitted by cable companies for
the use of the general public may require authorization from the broadcast/cable company, and/
or program owner.
■ A 75-ohm coaxial cable connector is built into the set for easy hookup.
When connecting the 75-ohm coaxial cable to the set, connect the 75ohm cable into the ANT. terminal.
■ Some cable TV companies offer premium pay channels. Since the
signals of these premium pay channels are scrambled, a cable TV
converter/descrambler is generally provided to the subscriber by the
cable TV company.
This converter/descrambler is necessary for normal viewing of scrambled channels.
(Set your TV to channel 3 or 4, typically one of these channels is used. If this is unknown,
consult your cable TV company.)
For more specific instructions on installing cable TV, consult your cable TV company.
One possible method of connecting the converter/descrambler provided by your cable TV
company is shown in the diagram below.
RF switch
(not included)
OUT
VHF/UHF IN
2 set signal
splitter
(not included)
A
IN
B
Cable TV converter/
descrambler
(not included)
■ The RF switch (not included) is required to provide two inputs (A and B). Setting
the RF switch to position A allows viewing of all unscrambled channels by using
the TV channel keys.
■ Setting the RF switch to position B allows viewing of all scrambled channels via
the converter/descrambler by using the converter channel keys.
16
Cable TV Line
Chapter 2 Installing the LCD TV
Use a supplied antenna cable to connect the TV signal to the LCD TV’s TV CABLE terminal.
ENGLISH
VHF/UHF IN
Connect the AC power cord at the back of the TV and connect the power cord to wall outlet.
Press the
button on the remote to turn on the LCD TV.
Always disconnect the LCD TV from the main voltage when the LCD TV will not
be used for a long period of time. The POWER button on the front panel is only
used for switching the LCD TV into standby, it does not disconnect the device
from the main voltage. To completely disconnect the main voltage, please
remove the power plug from the socket.
17
Chapter 2 Installing the LCD TV
Press the
button on the remote to turn on the LCD TV.
Press the Input button on the remote to display the Input List. Use the ▲▼ buttons to select
TV and press the OK button.
Input Source
TV(CABLE/AIR)
VIDEO1 (AV)
VIDEO2 (S-VIDEO)
VIDEO3 (YPbPr)
VIDEO4 (HDMI)
COMPUTER(VGA)
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the TV.
Channel Scan
Tuner Mode
Channel Skip
Favorite List
Time Zone
TV
Cable
Eastern Time
Select
Exit
Press the ▼ button to select Channel Scan, and press the OK button.
The Channel Scan automatically creates a list of receivable channels. Press the MENU
button at any time to interrupt the memorization process.(the list cannot be created if
interrupted)
Status: Scanning.....
Analog Channels: 25
Digital Channels: 0
Cable
47%
The Channel Scanning will create a list of receivable channels for the current
input (antenna or cable). You will be required to run Channel Scanning for each
RF input to create a list of available channels from both inputs.
Press the OK button to display the received channel list, then press ▲▼ to select a
channel. Or, use the ▪ with 0-9 buttons to select digital channel( for example 9.1)
Channel List
7-1 KABC-DT
9-1 KQED-HD
9-2 KOED-SD
8 CCT
12
13
15
The digital main channel might include many subchannels (for example 9-1, 92..) that are showing program at the same time.
18
Chapter 2 Installing the LCD TV
Connecting an A/V Device with Composite Connector
ENGLISH
Rear of TV
HDMI IN
Y
Pb
Pr
VIDEO IN S-VIDEO IN
COAXIAL
VHF/UHF IN
PC/VGA IN
PC AUDIO IN
L
AUDIO IN
R
L
AUDIO IN
R
GAME CONSOLE
AUDIO Cable
VIDEO OUT
L
AV Cable
D V D PLA YER
R
Use a composite cable to connect the external A/V device’s composite video/audio jacks to
the LCD TV’s VIDEO IN jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
To view the A/V device’s with component input, press the INPUT button on the remote to
select VIDEO1.
Not all A/V devices have the ability to connect to a TV. Please check your A/V devices
user guide for compatibility.
19
Chapter 2 Installing the LCD TV
Connecting an A/V Device with S-Video Connector
Rear of TV
HDMI IN
Y
Pb
Pr
VIDEO IN S-VIDEO IN
COAXIAL
VHF/UHF IN
PC/VGA IN
PC AUDIO IN
L
AUDIO IN
R
GAME CONSOLE
AUDIO Cable
S-VIDEO OUT
L
D V D PLA YER
R
S-VIDEO Cable
Use an audio cable to connect the external A/V device’s audio output jacks to the LCD
TV’s audio inputs. Use a S-Video cable to connect the external A/V device’s S-Video
output jack to the LCD TV’s S-Video IN input jack.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
To view the A/V device’s with component input, press the INPUT button on the remote
repeatedly to select VIDEO2.
20
Chapter 2 Installing the LCD TV
Connecting an A/V Device with Component(YPbPr) Connector
HDMI IN
Y
Pb
Pr
VIDEO IN S-VIDEO IN
ENGLISH
Rear of TV
COAXIAL
VHF/UHF IN
PC/VGA IN
PC AUDIO IN
Pb
Cb
L
AUDIO IN
R
L
AUDIO IN
R
Pr
Cr
GAME CONSOLE
COMPONENT
OUT
R
AUDIO Cable
L
COMPONENT Cable
Pr/Cr
Pb
Pb/Pb
Pr
D V D PLA YER
Y
Not all A/V device have the ability to connect to a TV. Please check your A/V
device user guide for compatibility.
Use a component cable to connect the external A/V device’s component output jacks to the
LCD TV’s YPbPr IN input jacks.
Use an audio cable to connect the external A/V device’s component audio jacks to the LCD
TV’s audio input jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
To view the A/V device’s with component input, press the INPUT button on the remote
repeatedly to select VIDEO3.
The component video jacks on your A/V device are sometimes labeled YPbPr,
or YCbCr. For an explanation of component video, see your A/V device’s user
guide.
21
Chapter 2 Installing the LCD TV
Connecting an AV Equipment with HDMI Connector
Rear of TV
HDMI IN
Y
Pb
Pr
VIDEO IN S-VIDEO IN
COAXIAL
VHF/UHF IN
PC/VGA IN
PC AUDIO IN
L
AUDIO IN
R
L
AUDIO IN
R
HDMI Cable
AV EQUIPMENT
Use a HDMI cable to connect the AV equipment’s HDMI output jack to the LCD TV’s HDMI IN
jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
Press the Input button on the remote to select VIDEO4.
The HDMI connector provides both video and audio signals, it’s not
necessary to connect the audio cable.
22
Chapter 2 Installing the LCD TV
Connecting an AV Equipment with DVI Connector
Rear of TV
Y
Pb
Pr
VIDEO IN S-VIDEO IN
ENGLISH
HDMI IN
COAXIAL
VHF/UHF IN
PC/VGA IN
PC AUDIO IN
L
AUDIO IN
R
L
AUDIO IN
R
AUDIO Cable
AUD IO
L
HDMI-to-DVI Cable
R
DVI IN
AV EQUIPMENT
Use a HDMI-to-DVI cable to connect the AV equipment’s DVI output jack to the LCD TV’s
HDMI IN jacks.
Use an audio cable to connect the AV equipment’s audio output jacks to LCD TV’s HDMI
AUDIO jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
Press the Input button on the remote to select VIDEO4.
If the LCD TV is connected to AV equipment’s DVI connector, you will need
an HDMI-to-DVI cable or an HDMI adapter(not supplied) and an audio cable.
23
Chapter 3 Using the LCD TV
Connecting a PC
Rear of TV
HDMI IN
Y
Pb
Pr
VIDEO IN S-VIDEO IN
COAXIAL
VHF/UHF IN
PC/VGA IN
PC AUDIO IN
L
AUDIO IN
R
L
AUDIO IN
R
AUDIO Cable
VGA Cable
PC
Use a D-SUB cable to connect the PC’s D-SUB output jack to the LCD TV’s VGA input
jack. Use an audio cable to connect the PC’s audio output jacks to LCD TV’s.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
Press the INPUT button on the remote to select COMPUTER.
24
Chapter 3 Using the LCD TV
Connecting an Audio Receiver or a Dolby Digital 5.1 Sound System
For better sound quality, you may want to use a Home Theater/Stereo System.
Although not recommended, if you prefer to use the TV audio output to make this connection to your
Home Stereo System, please follow the instructions below.
HDMI IN
Y
Pb
Pr
VIDEO IN S-VIDEO IN
COAXIAL
VHF/UHF IN
PC/VGA IN
PC AUDIO IN
L
AUDIO IN
R
L
AUDIO IN
R
AUDIO Cable
Audio Receiv
er
Use an audio cable to connect the audio receiver’s audio LINE IN jacks to LCD TV’s
COAXIAL jacks.
Connect all AC power sources, before turning on the power switch of the LCD TV or
other connected equipment.
Press the
button on the remote to turn on the LCD TV.
25
ENGLISH
NOTE: If you have a Home Theater/Stereo System that you would like to use with your new Element
Electronics TV, we recommend that you do NOT use your TV’s audio output for this connection. For
the best sound quality, our product testing has shown that you should connect your Home Theater/
Stereo System directly to your A/V device. I.E. You should connect your Home Theater/Stereo
System to your DVD player, Cable/Satellite box or other AV equipment.
Chapter 3 Using the LCD TV
Chapter 3
USING THE FEATURES
Wide Screen Viewing
Wide Screen function allows viewing of 4:3/16:9 images in wide screen mode, cycling through
the following wide screen settings. Press the P.SIZE button repeatedly to select the screen
format you want.
NORMAL
Displays at 4:3 aspect ratio
NORMAL is not available when
you are watching 720p, 1080i, or
1080p source.
FULL
Stretches the image vertically and
horizontally to keeps the image size
consistent in the center of the screen and
stretches the sides
WIDE
Stretches the image vertically and
horizontally to fill the screen at 1:1.85
aspect ratio
ZOOM
Stretches the image vertically and
horizontally to fill the screen at 1:2.35
aspect ratio
26
Chapter 3 Using the LCD TV
Using the Program Guide
With the LCD TV connected to a television programming source, press the INPUT button
on the remote control and use the ▲▼ buttons to select TV and press the OK button.
Press the GUIDE button on the remote control, the Program Guide will appear on the
screen:
Monday 15 January 2007 2:36:26 PM
3-1
7-2 KQED-SD
7-2
Today
7:00 PM
EYEWITHNESS NEWS 4PM
cc
Today
7:30 PM
ABC WORLD NEWS
cc
Today
9:30 PM
ABC’S MONDAY NIGHT FOOTBALL
cc
SPORTSZONE
cc
Tomorrow
12:30 AM
TV-PG
5:00 PM - 5:30 PM Mon, 20 Jan.
EYEWITHNESS NEWS
Press the ◄► button to select the channel.
Press the ▲▼ button to select the program from a list, the Program Guide provides
introduction about the current program being shown on each channel.
The Program information in the guide is provided by the broadcasters. It may sometimes
include only the channel number, without a program title or description.
Monday 15 January 2007 2:36:26 PM
3-1
7-2 KQED-SD
7-2
Today
7:00 PM
EYEWITHNESS NEWS 4PM
cc
Today
7:30 PM
ABC WORLD NEWS
cc
Today
9:30 PM
ABC’S MONDAY NIGHT FOOTBALL
cc
SPORTSZONE
cc
Tomorrow
12:30 AM
TV-PG
5:00 PM - 5:30 PM Mon, 20 Jan.
EYEWITHNESS NEWS
Press the GUIDE button again on the remote control to exit the Program Guide.
27
ENGLISH
The Program Guide feature brings all sorts of information to your screen, such as program title,
program duration, time remaining, rating information, closed caption, availability, etc.
Chapter 3 Using the LCD TV
Operating the Menu
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control, the on-screen menu will appear on the
screen. Use the ◄► buttons to select your main menu option.
VIDEO MENU:
Allows you to make adjustments to your picture settings.
▪ If the signal source is TV/VIDEO/S-VIDEO/YPbPr/
HDMI, the VIDEO MENU appears as:
Picture Mode
Contrast
Brightness
Saturation
Hue
Sharpness
Color Temperature
Noise Reduction
Video
User
▪ If the signal source is VGA, the VIDEO MENU
appears as:
Picture Mode
Contrast
Brightness
Color Temperature
Noise Reduction
VGA
50
54
54
0
5
Vivid
50
54
Medium
Medium
Select
Exit
Video
Select
Exit
AUDIO MENU:
Allows you to customize the audio options and effects.
▪ If the signal source is VIDEO/S-VIDEO/YPbPr/
HDMI/VGA, the AUDIO MENU appears as:
Bass
Treble
Balance
Sound Effect
Speaker
Audio
▪ If the signal source is TV, the AUDIO MENU
appears as:
Bass
Treble
Balance
Sound Effect
MTS
SPDIF Type
Audio Language
Speaker
50
50
0
Surround
On
Select
Audio
Exit
28
50
50
0
Surround
Stereo
Dolby Digital
English
On
Select
Exit
Chapter 3 Using the LCD TV
TV MENU:
Allows you to edit and label channels.
ENGLISH
Channel Scan
Tuner Mode
Channel Skip
Time Zone
Eastern Time
TV
Select
Cable
Exit
SETUP MENU:
Allows you to set up a variety of features: Language, Closed Caption, factory reset, Parental Control sleep
timer.
▪ If the signal source is TV/VIDEO/S-VIDEO/YPbPr,
the SETUP MENU appears as:
OSD Language
Time Setup
Closed Caption
Parental
Gamma
Reset Default
Setup
▪ If the signal source is HDMI/VGA, the SETUP
MENU appears as:
English
OSD Language
Middle
Time Setup
Parental
Gamma
Reset Default
Select
Exit
Setup
English
Middle
Select
Exit
Use the ▲▼ buttons to highlight the option of the sub-menu, and press the OK
button. While in adjustment mode, and use the ◄► buttons to change the value of
the item.
Press the EXIT button to exit the menu.
29
Chapter 3 Using the LCD TV
Customizing the VIDEO Settings
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the VIDEO.
Use the ▲▼buttons to highlight an individual VIDEO option, use the ◄► buttons to
change the setting, and press the MENU to exit the menu
▪ If the signal source is TV/VIDEO/S-VIDEO/YPbPr/
HDMI, the VIDEO MENU appears as:
Picture Mode
Contrast
Brightness
Saturation
Hue
Sharpness
Color Temperature
Noise Reduction
Video
User
▪ If the signal source is VGA, the VIDEO MENU
appears as:
Picture Mode
Contrast
Brightness
Color Temperature
Noise Reduction
VGA
50
54
54
0
5
Vivid
50
54
Medium
Medium
Select
Exit
Video
Select
Exit
The VIDEO menu includes the following options:
Picture Mode
Cycles among display types: Vivid/Hi-Bright/Cinema/Sport/User
Contrast
Controls the difference between the brightest and darkest regions of
the picture
Brightness
Controls the overall brightness of the picture
Saturation
Controls the color intensity
Hue
Controls the difference between the green and red regions of the
picture
Sharpness
Increase this setting to see crisp edges in the picture; decrease it for
soft edges
30
Chapter 3 Using the LCD TV
Color temperature
Color Temperature
R Gain
G Gain
B Gain
User
120
120
120
Color Temperature
Select
Back
Noise Reduction
Select to reduce the noise level of connected equipment: Off/Low/
Strong /Medium.
VGA
Press the OK button to enter the VGA Setting:
Auto Adjust
H.Position
V. Position
Clock
Phase
VGA
72
31
127
31
Enter
Select
Exit
▪ Auto Adjust
Press the OK button to automatically adjust the
display settings to optimize performance based on
the VGA mode
▪ H. Position
Adjusts the position of the picture left and right in the
window
▪ V. Position
Adjusts the position of the picture up and down in the
window
▪ Clock
Controls the width of the picture based on the VGA
mode
▪ Phase
Controls the signal phase, which can improve focus
clarity and image stability based on the VGA mode
31
ENGLISH
Adjusts color components independently to achieve a warm or cool
effect: Cool/Middle/Warm/User
▪ Warm:
Increases red tint
▪ Nature : Increases natural tint
▪ Cool :
Increases blue tint
▪ User :
Allows the user to adjust red, green and blue color
component levels independently.
Chapter 3 Using the LCD TV
Customizing the AUDIO Settings
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the AUDIO.
Use the ▲▼ buttons to highlight an individual AUDIO option, use the ◄► buttons to
change the setting, and press the MENU to exit the menu
▪ If the signal source is VIDEO/S-VIDEO/YPbPr/
HDMI/VGA, the AUDIO MENU appears as:
Bass
Treble
Balance
Sound Effect
Speaker
Audio
▪ If the signal source is TV, the AUDIO MENU
appears as:
Bass
Treble
Balance
Sound Effect
MTS
SPDIF Type
Audio Language
Speaker
50
50
0
Surround
On
Select
Audio
Exit
50
50
0
Surround
Stereo
Dolby Digital
English
On
Select
Exit
The AUDIO menu includes the following options:
Bass
Controls the relative intensity of lower-pitched sounds
Treble
Controls the relative intensity of higher pitched sounds
Balance
Adjusts the relative volume of the speakers in a multiple speaker
system
Sound Effect
Allows selection of an audio-enhancement technique from among the
following options: Surround/Live/Dance/Techno/Classic/Soft/Rock/
POP/Off
MTS
Allows you to listen to high-fidelity stereo sound while watching TV
▪ Stereo:
Use separate audio tracks for left and right speakers, if available
▪ SAP:
You can enjoy a second audio program from the speakers while
watching a scene in the original program
▪ Mono:
Allows mono output (useful when stereo is noisy or inconsistent)
32
Chapter 3 Using the LCD TV
SPDIF Type
Allows to selection of the digital sound format: PCM/OFF/Dolby
Digital
▪ Dolby Digital:
Select for surround sound (for stereo programs only)
▪ OFF:
Select OFF to turn off the external audio system
Audio Language
Allows to select the audio language: English/Spanish/French.
Speaker
Allows to select to turn on or off the TV speakers.
33
ENGLISH
▪ PCM:
The external audio system is connected to the AUDIO OUT of the
LCD TV
Chapter 3 Using the LCD TV
Customizing the TV Settings
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the TV.
Use the ▲▼buttons to highlight an individual TV option, use the ◄► buttons
changes the setting, and press the MENU exits the menu.
Channel Scan
Tuner Mode
Channel Skip
Time Zone
TV
Cable
Eastern Time
Select
Exit
The TV menu includes the following options:
Channel Scan
Press the OK button, the Channel Scanning automatically
creates a list of receivable channels.
Tuner Mode
Allows selection between CATV cable and antenna signal sources:
▪ AIR
Choose this setting if you are receiving TV channels with an antenna
(over the air)
▪ Cable
Choose this setting if you are receiving TV channels with a CATV
(cable TV)
Channel Skip
Allows addition/removal of channels on the channel list.
Press the OK button to display the Channel Skip menu:
2 ABC
Analog
3 DISC
Analog
4
Analog
5
Analog
6
Analog
7
Analog
8
Analog
9
Analog
10
Analog
Channel Skip
Select
34
Back
Chapter 3 Using the LCD TV
Press the ▼ button to select the desired channel, andpress the
OK button repeatedly to select show ( ) or hide( )
Allows selection of regional TV systems of USA: Eastern Time/
Indiana/Central time/Mountain Time/Arizona/Pacific Time/Alaska/
Hawaii
35
ENGLISH
Time Zone
Chapter 3 Using the LCD TV
Customizing the SETUP Settings
Press the
button to turn the LCD TV on.
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the SETUP.
Use the ▲▼ buttons to highlight an individual SETUP option, use the ◄► buttons to
change the setting, and press the MENU to exit the menu.
▪ If the signal source is TV/VIDEO/S-VIDEO/YPbPr,
the SETUP MENU appears as:
OSD Language
Time Setup
Closed Caption
Parental
Gamma
Reset Default
Setup
▪ If the signal source is HDMI/VGA, the SETUP
MENU appears as:
English
OSD Language
Time Setup
Parental
Gamma
Reset Default
Middle
Select
Exit
Setup
English
Middle
Select
Exit
The SETUP menu includes the following options:
OSD Language
Selects to display all on-screen menus in your language of choice:
English/French/Spanish
Closed Caption
Allows to select from analog or digital closed caption modes and
press the OK button. The Closed Captain list appears:
Analog Cloaed Caption
Digital Cloaed Caption
Digital Caption Style
Cloaed Caption
Off
Off
Select
Back
Analog Closed Caption:
Press the ◄► buttons to select the basic analog closed caption
options: OFF/CC1/CC2/CC3/CC4
▪ CC1 /CC2 /CC3 /CC4:
Display a printed version of the dialog and sound effects of the
program being viewed
▪ T1/T2:
Display station information presented using either half or the
whole screen
▪ T3/T4:
Extended Data Services. For example: Network name, program
name, program length, etc.
36
Chapter 3 Using the LCD TV
Digital Closed Caption:
Press the ◄► buttons to select the digital closed caption options:
Service1/Service2/Service3/Service4/Service5/Service6/OFF
Caption Style:
Press OK button to customize the settings for digital closed
caption option:
Custom
Caption Style
Font Size
Font Color
Font Opacity
Background Color
Background Opacity
Window Color
Window Opacity
Large
White
Solid
Black
Solid
Black
Translucent
Cloaed Caption Style
Parental
Select
Back
The Parental Control can be set up to the TV to block Channel,
Video Source and to change password.
Use the ▼ button to select the Parental, and press the OK to
display the Parental menu
Use the Program Block function, must enter a four-digit
password. The factory password is 0000
The Parental list appears:
Program Block
Allows to setup the TV and MPAA Rating
Lock options (refer to “Using the Program
Block Setting”).
U.S.TV Ratings
U.S. Movie Ratings
Canadian English Ratings
Canadian French Ratings
Block MPAA Unrated
Block TV Unrated
Parental Block
37
NO
NO
Select
Back
ENGLISH
Note: The setting here will be applied to each DTV channel
Chapter 3 Using the LCD TV
Allows to block digital channels.
Channel Block
2 ABC
Analog
3 DISC
Analog
4
Analog
5
Analog
6
Analog
7
Analog
8
Analog
9
Analog
10
Analog
Channel Block
Select
Back
Selects to block a Input source signal
Input Block
1
2
TV(CABLE/AIR)
VIDEO1 (AV)
3
VIDEO2 (S-VIDEO)
4
VIDEO3 (YPbPr)
5
VIDEO4 (HDMI)
6
COMPUTER(VGA)
Input Block
Change Password
Select
Back
Selects to change your password
Gamma
Allows adjustment of the display’s gamma correction, which fine
tunes both brightness and red/green/blue ratios: On/Off/Middle.
Reset Default
Press the OK button to restore factory settings
38
Chapter 3 Using the LCD TV
Using the Program Block Settings
Use the ▼buttons to highlight Parental, and press the OK button.
OSD Language
Closed Caption
Parental
Gamma
Reset Default
Setup
English
Middle
Select
Exit
Use the Parental function, must enter a four-digit password. The factory password is
0000.
Password
****
Program Block
Channel Block
Input Block
Change Password
Parental
Back
Parental
Enter
Select
Back
Use the ▼ button to select the Program Block, and press the OK to display the
Program Block menu.
U.S.TV Ratings
U.S. Movie Ratings
Canadian English Ratings
Canadian French Ratings
Block MPAA Unrated
Block TV Unrated
Parental Block
NO
NO
Select
Back
39
ENGLISH
Press the MENU button on the remote control to display the Main menu, and use the
◄► buttons to select the SETUP.
Chapter 3 Using the LCD TV
The Parental block menu includes the following options:
U.S. TV Ratings
Selects to activate the TV Rating programs.
Canadian English Ratings
Selects to activate the English Rating programs of Canada.
Canadian French Ratings
Selects to activate the French Rating programs of Canada
U.S. Movie Ratings
Selects to activate the MPAA Rating programs
Block MPAA Unrated
▪ YES:
Block all movies that are broadcast without a MPAA rating.
▪ NO:
Allows all movies that are broadcast without a MPAA rating
Block TV None Rating
▪ YES:
Block all movies that are broadcast without a TV rating.
▪ NO:
Allows all movies that are broadcast without a TV rating.
40
Chapter 3 Using the LCD TV
U.S. TV Ratings
The U.S.TV Rating has 2 rating methods: Content-Based Rating and Age-Based Rating.
The U.S.TV Rating includes the following options:
D
L
S
V
ENGLISH
A
FV
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Allowed Rating
U.S. TV Ratings
Blocked Rating
Select
Back
AGE-BASED
RATING
DESCRIPTION
TV-Y
All children
TV-Y7
Directed to children age 7 and older
TV-G
General Audience
TV-PG
Parental Guidance suggested
TV-14
Parents strongly cautioned
TV-MA
Mature Audience only
CONTENT-BASED
RATING
DESCRIPTION
FV
Fantasy violence
D
Suggestive dialogue
L
Strong language
S
Sexual situations
V
Violence
ALL
All contents are blocked
CONTENT-BASED
FV
D
L
S
V
AGE-BASED
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
: To block programs by both content and age.
Use the ◄►▲▼ buttons to select the rating you want and press the OK button repeatedly to
select BLOCK or UNBLOCK .
41
Chapter 3 Using the LCD TV
Canadian English Ratings
The Canadian Englsh Ratings includes the following options:
G
C8+
G
PG
14+
18+
Allowed Rating
Canadian English Ratings
Blocked Rating
Select
RATING
DESCRIPTION
G
All children
Back
C8+
Children 8 years and older
G
General programming
PG
Parental guidance
14+
Viewers 14 and older
18-
Adult programming
Use the ◄►▲▼ buttons to select the rating you want and press the OK button repeatedly to
select BLOCK or UNBLOCK .
Canadian English Ratings
The Canadian Englsh Ratings includes the following options:
G
8 ans+
13 ans+
16 ans+
18 ans+
Allowed Rating
Canadian English Ratings
Blocked Rating
Select
Back
RATING
DESCRIPTION
G
General programming
8 ans+
Not recommended for ages under 8
13 ans+
Not recommended for ages under 13
16 ans+
Not recommended for ages under 16
18 ans+
Programming restricted to adults.
Use the ◄►▲▼ buttons to select the rating you want and press the OK button repeatedly to
select BLOCK or UNBLOCK .
42
Specifications
U.S. Movie Ratings
G
PG
PG-13
R
NC-17
X
Allowed Rating
U.S. Movie Ratings
Blocked Rating
Select
Back
RATING
DESCRIPTION
G
General Audiences. Movie is appropriate for all ages
PG
Parental Guidance Suggested. May contain material not suited for younger
viewers
PG-13
Contains content that may not be appropriate for viewers under the age of
13
R
Restricted. Contains adult content, no one under 17 admitted without
parent
NC-17
No one 17 and under admitted
X
No one 17 and under admitted
Use the ◄►▲▼ buttons to select the rating you want and press the OK button repeatedly to
select BLOCK or UNBLOCK .
43
ENGLISH
The U.S. Movie Ratings is used for original movies rated by the Motion Picture Association of
America(MPAA) as broadcasted on cable TV and not edited for television.
The U.S. Movie Ratings includes the following options:
Specifications
SPECIFICATIONS
MODEL
LCD Panel
FLX-1510
FLX-1910
Panel Size
15.4” TFT LCD
19” TFT LCD
Brightness
200 Cd/m2
300 Cd/m2
Contrast Ratio
400:1
850:1
1280x800
1440 x 900
VIDEO
1
1
S-VIDEO
1
1
Max. Resolution
Input Connector
YPbPr/ AUDIO IN(L/R) 1
1
AUDIO IN(L/R)
1
1
PC/VGA IN
1
1
HDMI IN
1
1
PC AUDIO IN
1
1
COAXIAL
1
1
HEADPHONE
1
1
VHF/UHF IN
1
1
Power Source
AC100~240V, 50/60HZ, 1.2A AC100~240V, 50/60HZ, 1.2A
Power Consumption
50 W, standby < 5 W
65 W, standby < 5 W
Dimension
15.2 w x 13.6 h x 5.2 d inch
18 w x 15.9 h x 5.2 d inch
7.1 LB
12.3 LB
WEIGHT
MODEL
LCD Panel
Panel Size
22” TFT LCD
Brightness
400
Contrast Ratio
700:1
Max. Resolution
Input Connector
FLX-2210
1680x1050
VIDEO
1
S-VIDEO
1
YPbPr/ AUDIO IN(L/R) 1
AUDIO IN(L/R)
1
PC/VGA IN
1
HDMI IN
1
PC AUDIO IN
1
COAXIAL
1
HEADPHONE
1
VHF/UHF IN
1
Power Source
AC100~240V, 50/60HZ, 1.2A
Power Consumption
65 W, standby < 5 W
Dimension
20.8 w x 17.7 h x 6.3 d inch
WEIGHT
17.5 LB
Product specifications are subject to change without notice.
For service and support information, visit www.elementelectronics.com.
44
20070213
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement