User manual | installation manual

NOTE:
Drawings in this manual are
for illustration purposes
only, actual product may
vary. Manufacturer reserves >
ba gt change ay User Guide
specification or features
without prior notice. These instructions
are important please
Tested to ECE R44/04 ws read carefully and
Approval number 045152 retain for future use.
ST) CIT
9 MONTHS
Y
YEARS
К
For information on fitting
please contact:
T: 0161 702 5063 * * %
E: [email protected] a a = * *
* APPROVED +
ECE R44\04
www.kiddu.eu Child Car Seat a
045152
ECE R44/04
Dear Parents,
Congratulations on the purchase of your
Kiddu Lane, Child Car Seat.
You have made an excellent choice; every
Kiddu product has been tested to exceed
required safety standards and is
manufactured using high quality materials and
components.
Our aim is to produce products that will help
your child develop and will make learning new
skills an enjoyable experience for both infants
and parents. We appreciate that time with your
child is precious and hope that the purchase
of this Kiddu product will enhance your time
together.
Contents
© 1 x Backrest
9 1 x Booster Seat
9 1 x Reversible Cushion
Q 1 x Safety Belt Buckle (detachable)
Assembly Before Use
To set up your car seat, remove all packaging and set down
on a flat surface. Your child seat consists of 2 parts, the
booster seat and back rest. Ensure that both pieces are lying
flat and facing upwards before assembly (Fig A)
Place the 2 hooks that are located at the bottom of the
backrest over the bars that are located on the booster seat
section. Ensure they are correctly aligned.
With one hand placed over the joint where the hooks are
placed in the gaps, use your free hand to push the backrest
up along the path of the arrows, until it is in the upright
position and the hooks are engaged.
WARNING: Do NOT force the backrest into the upright
position until it is aligned correctly.
Note: The car seat will stand upright when it is placed into
the car as intended i.e. the backrest will be supported by the
back of the car’s own seat. Therefore it will not have an
audible click when pushed up. O
f N
Your Lane car seat is
now ready for use.
Group 1 (9 - 18kgs)
1. To fit your Lane car seat
on the rear passenger seat
with the cars 3-point safety
belt system, ensure that the
seat is upright and as close
to the passenger seat
cushion as possible.
2. Thread the diagonal
vehicle seatbelt through the
fabric seat belt slot (marked
by a red arrow) and the lap
strap under the ‘arm’ of the
booster seat.
3. Pass the seat belt through the
back of the seat (underneath the
harness straps), and through the
parallel seatbelt slot.
4. Hook the seatbelt over the
parallel ‘arm’ of the booster seat,
and click the seat belt in place.
5. Ensure that the seatbelt is
not twisted.
6. Tighten the seat belt until
your car seat feels secure by
threading as much of it back
into the car's seatbelt slot and
pull the seatbelt firmly to lock
it into position.
To secure the harness
Manoeuvre the left and
right shoulder straps over
your childs shoulders, and
bring the two metal prongs
together. Click the joined
‘prong’ into the waist
buckle.
Adjusting the harness
In the centre of the booster
seat, underneath the Kiddu
logo, you will find a small
button. Pressing this will
release the harness and allow
you to manoeuvre the
harness into a position that
best fits your child. As your
child grows, remove the
support pad and adjust the
harness by removing the
shoulder straps individually
from the metal slider plate at
the back of the seat, and
inserting them through the
higher slots.
Group 2 (15-25kgs)
1. When your child is
between 15-18kgs, and
ready for Group 2,
remove the harness
altogether.
2. Thread the car's 3
point lap belt under both
armrests and over the
lap of your child, and
position the diagonal
belt through the
headrest (marked by
red arrows) and insert
the belt into the buckle
as normal. It is very
important that the
seatbelt is threaded
correctly through the
headrest.
3. Ensure that the car seat
is secure. Make sure that
the seatbelt is not twisted.
The headrest is
manoeuvrable, and should
be adjusted as your child
grows. Adjust the height by
gently pulling the headrest
upwards until it ‘clicks’ into
place.
The top of the headrest
must never be below the
eyeline of your child.
у
J
— 7)
J
ZÑ — A
>
NT
y
M
2
—
7
©
[]
\
h
/
y
Group 3 (22-36kgs)
Ensure that all harnesses and pads have been
removed. Remove the back cushion by placing
the base on a flat surface, and pushing the
backrest down until the seat is completely flat.
You should then be able to lift the backrest off
the booster seat.
Place the booster seat onto the rear passenger
seat in a forward facing position. Once your child
is seated on the cushion, thread the cars safety
belt under both armrests and over your childs
lap, making sure that the seatbelt is not twisted.
Thread the diagonal belt above the armrest, then
fix the belt into the buckle as normal.
Harness Threading Guide
1. Thread the strap with the
metal plate hanger through
the spring metal button in
the top side of the front
edge of the booster seat.
The metal hanger plate
should come out from
underneath the seat, and
the other end comes out
through the front of the
booster seat to use as the
one pull adjustment end.
2. Take the strap with the
shoulder pads attached at
either end, and thread one
pad through the harness
slot for the required
shoulder height you need,
through the seat pad, seat
cover and the slots in the
shell. And thread the other
shoulder pad in through the
back so the front and back
appear like in the images.
3. Next you take the long
strap, pass this through one
of the 2 gaps in the booster
seat and back up through
the gap on other side. Then
take the 2 ends, thread
them through the shoulder
pads and then through the
same holes you have
passed the shoulder pads
and they should hang down
the back like the 3rd image
above.
4. Insert these harness
ends into the metal hanger
plate at the back which
comes out from the bottom
of the booster seat. Ensure
they are locked into position
and test by pulling.
5. The buckle has a metal
retaining plate attached
which threads through the
slot near the front of the
booster seat (through the
cover and the shell) as
illustrated. Buckle up the
harness as normal and
check it all works and holds
as it should do.
©
©
©
©
©
©
Safety Warnings
Please read thoroughly before commencing installation,
as an incorrect installation could be dangerous.
Parents should not under any circumstances use this child
restraint on a passenger seat equipped with an airbag.
The child seat must only be installed in the forward facing
position.
It is most important that the seat belt is correctly routed
and the child seat tightened down on the upholstery as
firmly as possible to ensure maximum protection.
It is dangerous to make any alterations or additions to the
car seat without the approval of Kiddu, and it is dangerous
not to follow the installation instructions provided by
Kiddu.
Kiddu recommends that this car seat must not be used
when it has been subjected to the violent stresses in a
motor vehicle accident.
Do not leave the child in their child restraint unattended.
Ensure that no part of the seat or seat belt is trapped in a
door or a folding seat. If your car has a folding rear seat,
ensure that it is correctly latched in its upright position.
This car seat is provided with a fabric cover. It should be
kept away from sunlight as it may become too hot at times
for the childs skin
QO The safety belt buckle is not fully tamper proof and
therefore your child should be persuaded to never play
with it.
It is important to ensure that the lap strap is worn low
down as this secures the pelvis.
The rigid items and plastic parts of a child restraint must
be located and installed so that they are not liable, during
everyday use of the vehicle, to become trapped by a
movable seat or in a door of the vehicle.
Only suitable if the approved vehicles are fitted with 3
point safety belts approved to UN/ECE R16 or other
equivalent standards.
The child restraint must not be used without the cover.
The seat cover, should not be replaced with anything other
than the one recommended by the manufacturer as the
cover constitutes an integral part of the restraint perfor-
mance.
Kiddu can only guarantee the seat when the original
owner uses it.
Remove the headrest of the passenger seat being used if
it causes an obstruction for proper installation of the seat,
but do not forget to refit the headrest after use.
When the child seat is not in use, it is recommended that it
is fastened into the car with a seat belt to avoid it being
thrown in the event of an accident.
Q In an emergency your child can be released quickly by
pressing the red button on the seat belt buckle.
© Store this child seat in a safe place when it is not being
used. Avoid placing objects on top of it.
© If you travel with passengers using both the front and rear
passenger seats, the lighter occupants should be in the
rear and the heavier occupants in the front of the vehicle.
9 Do not allow your child seat to come into contact with
corrosive substances e.g. battery acid.
Q Itis recommended that any straps holding the restraint to
the vehicle should be tight, so that strap can not be
twisted.
Q Itis recommended that any luggage or other objects liable
to cause injuries in the event of a collision should be
properly secured.
9 Do not use any load bearing contact points other than
those described in the instructions and marked in the child
restraint.
9 Please keep these instructions for future reference.
WARNING
Your child seat can only be fitted into the passenger
seat of a car with a lap and diagonal seat belt and
without an airbag. Do not use any load bearing contact
points other than those described in the instructions
and marked in the child restraints. The vehicle seat
buckle is not positioned in or in front of the specified
(labelled) belt guide of the child restraint system.
NOTICE
9 This is a ‘Universal’ child restraint. It is approved to
ECE R44/04 series of amendments, for general use in
vehicles and it will fit most, but not all car seats.
© À correct fit is likely if the vehicle manufacturer has
declared in the vehicle handbook that the vehicle is
capable of accepting a ‘Universal’ child restraint for this
age group.
© This child restraint has been classified as ‘Universal’
under more stringent conditions than those which applied
to earlier designs which do not carry this notice.
Q If in doubt, please contact [email protected]
EXTREME HAZARD
Do not use in passenger seats equipped
with airbags (SRS)
The correct use and maintenance of your car seat will
ensure it gives long and trouble free use. When
somebody else is using your car seat, ensure they also
know how to use it, especially the correct way to adjust
it. The safety of your child is your responsibility.

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project