Advertisement
Advertisement
F-7HS
7" Full HD
High Brightness Field Monitor
Operation manual_V1.1
CONTENTS
01
02
03
04
05
CAUTION
MAIN FEATURES
CONTROLS & FUNCTIONS
MENU TREE & ADJUSTMENT
MENU OPERATIONS
[1] PICTURE
[2] COLOR
[3] MARKER
[4] DISPLAY / VIDEO
[5] WAVEFORM
[6] AUDIO
[7] SYSTEM
09
10
11
06
07
08
BUTTON FUNCTIONS
OTHER FUNCTIONS
AVAILABLE SIGNAL FORMATS
VIDEO SUPPORT RESOLUTION
PRODUCT SPECIFICATIONS
OPTIONAL ACCESSORIES
24p
26p
39p
40p
41p
42p
04p
06p
07p
10p
11p
11p
12p
15p
16p
19p
21p
22p
FHD Hight Bright Field Monitor
01 CAUTION
• Always use set voltage. (DC 12V 1.8A / 34V 0.6A)
• When using a DC Adapter other than the one
supplied by the manufacturer, please be advised
that the adapter with DC 12V/3A ~ 6A can be
compatible with the monitor.
• All operating instructions must be read and
understood before the product is operated.
• These safety and operating instructions must be
kept in safe place for future reference.
• All warnings on the product and in the instructions
must be observed closely.
• All operating instructions must be followed.
• Do not use attachments not recommended by the
manufacturer. Use of inadequate attachments
can result in accidents.
• This product must be operated on a power
source specified on the specification label.
• If you are not sure of the type of power supply
used in your home, consult your dealer or local
power company. For units designed to operate
on batteries or another power source, refer to the
operating instructions.
• The power cords must be routed properly to
prevent people from stepping on them or objects
from resting on them. Check the cords at the
plugs and product.
• In case of using other 12V DC adapters instead of
the standard adapter provided by the manufacturer,
please check the proper load capacity (or current
capacity) and use an adapter with stable voltage.
• Do not overload DC outlets or extension cords.
Overloading can cause or electric shock.
• Never insert an object into the product through
vents or openings. High voltage in the product,
and inserting an object can cause electric shock
and/or short internal parts. For the same reason,
do not spill water or liquid on the product.
• Do not attempt to service the product yourself.
Removing covers can expose you to high voltage
and other dangerous conditions. Request a
qualified service person to perform servicing.
• If any of the following conditions occurs, unplug
the power cord from the DC outlet, and request a
qualified service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or
when objects have fallen into the product.
c. When the product has been exposed to rain or
water.
d. When the product does not operate properly as
described in the operating instructions. Do not
touch the controls other than those described
in the operating instructions.
Improper adjustment of controls not described
in the instructions can cause damage, which often
requires extensive adjustment work by a
qualified technician.
e. When the product has been dropped or
damaged.
f. When the product displays an abnormal
condition.
Any noticeable abnormality in the product
indicates that the product needs servicing.
• In case the product needs replacement parts,
make sure that the service person uses replacement
parts specified by the manufacturer, or those with
the same characteristics and performance as the
original parts. Use of unauthorized parts can
result in fire, electric shock and/or other danger.
• Upon completion of service or repair work, request
the service technician to perform safety checks to
ensure that the product is in proper operating
condition.
• Unplug the power cord from the DC outlet before
cleaning the product. Use a damp cloth to clean
the product. Do not use liquid cleaners or aerosol
cleaners.
• Unplug the power cord from the AC outlet if you
do not use the product for considerably long time.
FHD Hight Bright Field Monitor
01 CAUTION
• Do not use the product near water, such as bathtub,
washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.
• Keep the product away from direct rays of the
Sun-light.
• Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on an
unstable base can cause the product to fall,
resulting in serious personal injuries as well as
damage to the product. Use only a cart, stand,
tripod, bracket or table recommended by the
manufacturer or sold with the product. When
mounting the product on a wall, be sure to follow
the manufacturer’s instruction. Use only the
mounting hardware recommended by the
manufacturer.
• When relocating the product placed on a cart, it
must be moved with the utmost care.
• The power cord plug shall be connected to a
MAINS socket outlet with a protective earthing
connection.
• Infrared devices can cause noise or malfunction
under condition as below.
- Parts of the body come into contact with the
infrared transmiter or acoustic device.
- Obstacles can cause electrical changes if there is
a partition in the middle or in the wall.
- Exposure to radio interference from medical
equipment, microwave ovens, wireless LAN
devices, etc. with the same frequency band.
[NOTE]
* If the product is used with the MAXIMUM
brightness at a high temperature for extended
period of time, the front and rear housing
may get very hot. Be sure not to keep using
the product with the MAXIMUM brightness.
We recommend the user takes an occasional
break when using.
• Unplug the power cord from the AC outlet when
happening any problem in the product.
• Sudden stops, excessive force and uneven floor
surface can cause the product to fall from the cart.
• The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block
these vents and openings since insufficient
ventilation can cause overheating and/or shorten
the life of the product. Do not place the product
on a bed, sofa, rug or other similar surface, since
they can block ventilation openings. This product
is not designed for built-in installation; do not
place the product in an enclosed place such as a
bookcase or rack, unless proper ventilation is
provided or the manufacturer’s instructions are
followed.
• In case of installation the product on the rack, the
inside of the product would be overheated due to
heat from other devices near by and the decrease
of air circulation, which could damage to the
monitor. To prevent the damage, please have
enough space for the monitors and use fan to
avoid heat and maintain the operating temperature.
(Refer to the specication of the product).
• The LCD panel used in this product is made of
glass. Therefore, it can break when the product is
dropped or applied with impact. Be careful not to
be injured by broken glass pieces in case the LCD
panel breaks.
• Keep the product away from heat sources such as
radiators, heaters, stoves and other heat generating
products (including amplifiers).
5
FHD Hight Bright Field Monitor
02 MAIN FEATURES
F-7HS Monitor contains the following features :
• Compatible with various SDI signals formats
- This product is compatible with various SDI
signals : 480i, 576i, 720p, 1080i, 1080p, 1080psf
• HDMI Signal
- This product is compatible with various HDMI
signals.
• HDMI To SDI / SDI To HDMI Conversion Output
- This product features an HDMI To SDI conversion
output so that video source from HDMI In
terminal can be output through SDI Out terminal.
- The SDI To HDMI conversion output is also
supported. The video source from SDI In terminal
can be output through HDMI Out terminal.
• Audio Out
- Stereo Audio Out through phone Jack.
• Knob Control
- Easy to adjust user configuration using the
control knob on the top of the monitor.
• Custom 3D LUT Import
- Allows the users to load their own created
3D LUT files generated by color grading tools
and apply them to the monitor.
• Integrated Camera LUT
- LUTs for every major camera manufacturers are
integrated to the F-7HS, and they can be
applied to the live input video.
- Log-C, C-Log, S-Log1, S-Log2, S-Log3, RED
Gamma 3, RED Gamma 4
• Advanced Color Adjustment OSD
- Provides various color adjustment menus
which enable the user to monitor the video
signal in the optimal settings.
• Waveform & VectorScope
- Provides various modes: Waveform,
VectorScope, Waveform Wide, Waveform YCbCr,
Waveform RGB, Waveform & VectorScope,
Waveform YCbCr & VectorScope, Waveform Full,
VectorScope Full
• Audio Level Meter: 16 Channel, Direction
adjustable, Pair or Group selectable, Size
changeable(Small, Large)
• Video Range Adjustment: Limited 109%, Full
• Various Marker
• Grid Display: 3x3, 4x4, 5x5, 6x6
• Timecode Display: LTC, VITC
• ARRI Camera Status: LDS Info, Index Letter
• Various Scan: Zero Scan, Over Scan, 1:1 Scan
• User Aspect
• H Flip, V Flip, H/V Flip: Manual, Auto
• Focus Assist
• H/V Delay
• Blue/Mono Only
• Various Aspect: 16:9, 4:3, 2.35:1, 1.85:1, 15:9, 16:10
• Anamorphic: 1.3X, 1.5X, 1.8X
• Luma(Y’) Zone Check
• Range Error
• Zoom: 10%, 20%, ..., 90%
• Zoom Split: Left-Top, Right-Top, Left-Bottom,
Right-Bottom, Center
• Freeze
• Internal Pattern Display
• Tally Lamp and Screen Tally
• Remote Control via RS-422(RJ-45)
• GPI Control via REMOTE port
• Firmware Update & Calibration via USB(A Type)
• Power
- Basically, the product is powered by a normal
DC source.
- The product can be battery-powered.
* DC 12V 1.8A / 34V 0.6A (Typical)
6
03 CONTROLS & FUNCTIONS
F-7HS ALL PART
FHD Hight Bright Field Monitor
MENU<EXIT>
SOURCE
KNOB FUNCTION/
FUNCTION SELECT
PHONEJACK
HDMI OUT
HDMI IN
USB
REAR TALLY
SDI OUT
SDI IN
POWER BUTTON
DC POWER
/TALLY
7
FHD Hight Bright Field Monitor
03 CONTROLS & FUNCTIONS
TOP / FRONT
• [MENU/EXIT/SOURCE] Button
- Used to activate the OSD menu.
- When the OSD menu is activated, press this
button to exit from the menu.
- Press the button for more than 2 seconds to
activate Input Select menu. (SDI, HDMI)
- Use the [ENCODER] Knob to change the Input
Signal.
• [UP/DOWN/ENTER] Knob
- Used to move within the menu when OSD menu
is activated, and is also used to decrease or
increase the value of the selected feature.
- Press the knob to select the main menu and the
sub menus.
- Press the button for more than 2 seconds to
activate the HOT Key menu.
(VOLUME / BRIGHTNESS / CONTRAST / CHROMA
/ SHAPRNESS / PEAKING BOOST)
• [F1]~[F3] Button
- Press the button for less than 2 seconds to
activate the function.
- Press the button for more than 2 seconds to
activate Function Select menu.
(Scan, Aspect, H/V delay, etc.)
- Press the button for more than 2 seconds to
indicate previously selected function.
- Use the Knob to change the function.
8
FHD Hight Bright Field Monitor
03 CONTROLS & FUNCTIONS
SIDE & BOTTOM / REAR
• [HDMI IN]
- Signal input terminal for HDMI signal.
• [HDMI OUT]
- Signal output terminal for HDMI signal.
- Video source from SDI input terminal can be
converted to HDMI format.
• [HEADPHONE] (Phone Jack)
- Used for Stereo Audio Output through Phone
Jack. (video signals with embedded audio only)
• [USB]
- This terminal is used to upgrade the firmware or
color calibration made by TVLogic.
• [REAR TALLY]
- Activates same as [SCREEN TALLY].
• [SDI OUT] (BNC)
- Signal output terminal for HD/SD/3G SDI signal.
- Video source from HDMI input terminal can be
converted to SDI format.
* SDI Output is not activated when the
unit is turned off or in Standby mode.
• [SDI IN] (BNC)
- Signal input terminal for HD/SD/3G SDI signal.
• [POWER] Switch
- Used to turn the power on and off.
• [DC POWER / TALLY] (XLR 4P)
- Tally Signal In Level DC 5V ±2V
- Battery Power Input terminal for DC 12V
- Rated Power Input : DC 12V 1.8A / 34V 0.6A
* When using a DC Adapter other than the one
supplied by the manufacturer, please be advised
that the adapter with DC 12V/3A ~ 6A can be
compatible with the monitor.
< Warning! >
When using the product make sure to ground, whenever possible, before connecting the input signal cable in order to prevent any possible damage to the product or connected devices.
The damage may include signal noise, malfunction of main board or display panel. And the connected devices such as camera or video source player may also be influenced through signal cable.
Please check if the AC power source and the power extender or power distributor is grounded.
9
FHD Hight Bright Field Monitor
04 MENU TREE & ADJUSTMENT
MENU TREE & MENU CONTROL & MENU CONTROL SEQUENCE
[1] MENU TREE
• OSD(On-Screen Display) Menu helps to use
various different functions.
• This Picture is the menu structure for F-7HS.
PICTURE 같이
BRIGHT
CONTRAST
CHROMA
SHARPNESS
PEAKING BOOST
KNOB LOCK
3DLUT LOAD
3DLUT SYNC
3DLUT IMPORT 1
3DLUT IMPORT 2
3DLUT IMPORT 3
UNLOCK
REC 709
SYNCHRONIZATION
NONE 1
NONE 1
NONE 1
F-7HS
+90
+90
+40
0
0
[3] MENU CONTROL SEQUENCE
• Menu control sequence follows the order below.
1 .
Press MENU button to activate the OSD menu.
2. Move to a desired menu using the Knob.
3. Press the Knob to select a menu and move to
select a sub-menu by scrolling the Knob.
4. Press the Knob to select the desired sub menu.
(The selected sub-menu will be highlighted)
5. Press the ENTER button or the MENU button
to save the new value after adjusting the value
by scrolling the Knob.
6. Press MENU button to return to previous menu
and if there is no previous menu, the OSD menu
will be removed from the screen.
[2] MENU CONTROL
• User may control various functions using the
MENU button and the Knob on the top of the
monitor.
10
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[1] PICTURE
PICTURE 같이
BRIGHT
CONTRAST
CHROMA
SHARPNESS
PEAKING BOOST
KNOB LOCK
3DLUT LOAD
3DLUT SYNC
3DLUT IMPORT 1
3DLUT IMPORT 2
3DLUT IMPORT 3
UNLOCK
REC 709
SYNCHRONIZATION
NONE 1
NONE 1
NONE 1
F-7HS
+90
+90
+40
0
0
• BRIGHT
- Used to set the brightness(=offset) level from
-100 to 100.
* Brightness can be adjusted by using the Knob
on the top of the monitor.
• CONTRAST
- Used to set the contrast(gain) level from -100 to
100.
* Contrast can be adjusted by using the Knob on
the top of the monitor.
• CHROMA
- Used to set the saturation level from -50 to 50.
* Chroma can be adjusted by using the Knob on the top of the monitor.
• SHARPNESS
- Used to set the Sharpness level from 0 to 24.
* Sharpness can be adjusted by using the Knob
on the top of the monitor.
• PEAKING BOOST
- Used to set the Peaking Boost level from 0 to 24.
* Peaking Boost can be adjusted by using the
Knob on the top of the monitor.
• KNOB LOCK
- Locks the Knob control.
- If [KNOB LOCK] is set to [LOCK], the Knob is
activated only when the OSD pops up.
While the OSD doesn't pop up, the Knob is
deactivated.
• 3DLUT LOAD
- Used to apply the internally stored 3D LUT.
- Maximum three files of 3D LUT can be stored.
- The file name can be set up to 20 characters
including the extension.
• 3DLUT SYNC
- Used to load a list of available 3D LUT files
currently stored in the FLASH MEMORY.
- Available 3D LUT format is CUBE.
- Available sizes of the 3D LUT are 17 or 33.
• 3DLUT IMPORT 1/2/3
- Used to save the 3D LUT stored in the external
memory to the internal memory 1/2/3 area.
- Once saved, the 3D LUT can be maintained
even when the power is turned ON/OFF.
- The file name can be set up to 20 characters
including the extension.
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[2] COLOR
COLOR 같이
STANDARD
VIDEO RANGE
PEAK LUMINANCE
BLACK LEVEL
COLOR GAMUT
COLOR TEMP
EOTF
LOCAL DIMMING
EETF
HLG SG
S . G
CAM LUT
CAM LUT THROUG
HD
LIMITED109
100
0.001
BT709
6500K
2.4
OFF
OFF
OFF
OFF
OFF
F-7HS
PAGE (1/2)
• STANDARD
- Used to select the color and dynamic range of
the screen.
- Available options are HD, UHD, DCI-P3, PQ, HLG,
SLog3 and User1/2/3.
• VIDEO RANGE
- Used to select the range of digital video signal.
- [FULL]: ]: Input signal 1~254(8bit), 4~1019(10bit)
- [LIMITED109]: Input signal Y': 16~254, CbCr:
16~240(8bit) / Y': 64~1019, CbCr: 64~1019(10bit)
*Activates only in [STANDARD - USER 1/2/3] mode.
• PEAK LUMINANCE
- Used to select the Peak Luminance of the
monitor.
- Selectable levels are [100] ~ [1000] with 100
increment, [1000] ~ [10000] with 1000 increment.
*Activates only in [STANDARD - USER 1/2/3] mode.
• BLACK LEVEL
- The minimum black level of the video signal
can be set differently depending on the
performance of the monitor or the lighting
environment.
- Available modes are from [0.000] to [0.010]
with 0.001 increment, from [0.010] to [0.100]
with 0.010 increment, from [0.100] to [0.900]
with 0.100 increment.
* Activates only in the User1/2/3 mode.
• COLOR GAMUT
- Used to select the standard color gamut.
- Available options are BT709, DCI, BT2020, NATIVE.
*Activates only in [STANDARD - USER 1/2/3] mode.
• COLOR TEMP (Color Temperature)
- Controls the color temperature.
- Available options are 6500K, 9300K, USER 1/2/3.
*Activates only in [STANDARD - USER 1/2/3] mode.
• EOTF (Electro-Optical Transfer Function)
- Electrophotic conversion Functions(ex: Gamma
or HDR curve).
- Available modes are 2.2, 2.4, 2.6, PQ, HLG and
SLOG3.
*Activates only in [STANDARD - USER 1/2/3] mode.
• LOCAL DIMMING (* Not Supported)
- Used to set the Local Dimming Backlight mode.
- This mode is supported by the local dimming
backlight model and does not support F-7HS.
12
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[2] COLOR
COLOR 같이
STANDARD
VIDEO RANGE
PEAK LUMINANCE
BLACK LEVEL
COLOR GAMUT
COLOR TEMP
EOTF
LOCAL DIMMING
EETF
HLG SG
S . G
CAM LUT
CAM LUT THROUG
HD
LIMITED109
100
0.001
BT709
6500K
2.4
OFF
OFF
OFF
OFF
OFF
F-7HS
PAGE (1/2)
• EETF (Electrical-Electrical Transfer Function)
- Used to display the HDR image(without clipping)
within the actual luminance range (black level
and peak luminance) that the monitor can
express. In the ON mode, the HDR image is
converted within the range of set peak luminance
and black level. In the OFF mode, the video
signal outside of the set range is clipped.
- Available modes are OFF and ON.
- Available only when the EOTF is set to PQ or
SLOG3.
*Activates only in [STANDARD - USER 1/2/3] mode.
• HLG SG (HLG System Gamma)
- Used to set the System Gamma of HLG mode.
- In the ON mode, the value of the System
Gamma changes automatically according to the
previously set peak luminance. When it is OFF,
the value is set to default value of 1.2.
* Activates only when the EOTF is set to HLG, and
STANDARD is set to USER 1/2/3.
• SG (System Gamma)
- The System Gamma of HLG is automatically
calculated and displayed according to the set
[PEAK LUMINANCE].
- Activates only when the EOTF is set to HLG and
the HLG SG is ON.
PEAK LUMINANCE
100
200
300
400
500
600
700
800
900
1000
2000
3000
4000
5000
6000
7000
8000
9000
10000
SG (System Gamma)
0.78
0.91
0.98
1.03
1.07
1.11
1.13
1.40
1.45
1.49
1.53
1.16
1.18
1.20
1.33
1.55
1.58
1.60
1.62
• CAM LUT (Camera LUT)
- Used to change the Camera LUT.
- Available LUTs are LOG-C, C-LOG, S-LOG1,
S-LOG2, S-LOG3, REDGAMMA3, REDGAMMA4.
* Activates only when STANDARD is set to USER
1/2/3, and EOTF is set to 2.2, 2.4, 2.6.
• CAM LUT THROUG (Camera LUT Through)
- Apply the currently applied LUT to Through Out.
13
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[2] COLOR
COLOR 같이
COLOR TEMP
GAIN RED
GAIN GREEN
GAIN BLUE
BIAS RED
BIAS GREEN
BIAS BLUE
COLOR COPY
COLOR SPACE
6500K
6500K
BT709
PAGE (2/2)
• COLOR TEMP
- Controls the color temperature and allows
instant access to preset the color temperature
settings.
- Available color temperatures are 6500K, 9300K
and User1/2/3.
* In User 1/2/3 modes, user can define custom
RGB GAIN, BIAS (=Offset) and Color Copy values.
• GAIN RED / GREEN / BLUE
- Used to set Red/Green/Blue Gain (or Picture,
Contrast) level from -256 to 255.
* Available only in User 1/2/3 mode.
• BIAS RED / GREEN / BLUE
- Used to set Red/Green/Blue Bias (or Offset,
mainly affects on Black level) from -100 to 100.
* Available only in User 1/2/3 mode.
F-7HS
- 5
- 5
- 6
+ 0
+ 0
+ 0
• COLOR COPY
- Used to copy the R/G/B Gain value of pre-stored
color temperature settings.
- In User mode, find and select the color
temperature and press the Knob to copy and
apply the Gain value to GAIN RED, GAIN GREEN,
GAIN BLUE.
* Available only in User 1/2/3 mode.
• COLOR SPACE
- Used to select the standard color space.
- Available options are BT709, DCI, BT2020, NATIVE.
14
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[3] MARKER
MARKER 같이
ENABLE
MARKER
CENTER MARKER
SAFETY AREA
FIT MARKER
MARKER MAT
MARKER COLOR
THICKNESS
USER MARKER H1
USER MARKER H2
USER MARKER V1
USER MARKER V2
GRID ENABLE
GRID TYPE
GRID THICKNESS
GRID TRANS
GRID THROUGHOUT
ON
OFF
OFF
OFF
OFF
OFF
WHITE
2
OFF
OFF
1
OFF
OFF
F-7HS
+ 1
+1920
+ 1
+1080
• ENABLE
- Used to activate the Marker function.
• MARKER
- Available Marker types are OFF, 16:9, 4:3, 4:3 ON
AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1 & 4:3 and
USER.
• CENTER MARKER
- Displays the Center Marker on the screen.
• SAFETY AREA
- Used to select and controls the size and
availability of the Safety Area.
- Available sizes are 80%, 85%, 88%, 90%, 93%,
100%, EBU ACTION 16:9, EBU GRAPHIC 16:9, EBU
ACTION 14:9, EBU GRAPHIC 14:9, EBU ACTION 4:3
and EBU GRAPHIC 4:3.
• FIT MARKER
- Used to activate or inactivate the Fit Marker
function.
- When the Marker type is selected in the Marker
menu, a border line of the Safety Area will be
displayed inside the Marker. Images below show
the difference between Fit Marker ON and OFF.
• MARKER MAT
- Used to set the darkness level outside of the
MARKER area from OFF(transparent) to 7(Black).
- The bigger the value, the darker the color.
MARKER : 4:3
SAFETY AREA : 90%
FIT MARKER : OFF
MARKER : 4:3
SAFETY AREA : 90%
FIT MARKER : ON
• MARKER COLOR
- Used to set the color of the MARKER lines.
- Available colors are WHITE, YELLOW, CYAN,
GREEN, MAGENTA, RED, BLUE, BLACK.
• THICKNESS
- Used to set the thickness of the MARKER lines.
- Thickness level is from 1 to 7 by the pixel unit.
• USER MARKER H1/H2
- Used to set the position of the first and second
horizontal marker lines.
- Displayed when the MARKER menu is set to USER.
• USER MARKER V1/V2
- Used to set the position of the first and second
vertical marker lines.
- Displayed when the MARKER menu is set to USER.
• GRID ENABLE
- Used to activate the GRID lines.
• GRID TYPE
- Available grid types are 3X3, 4X4, 5X5, 6X6.
• GRID THICKNESS
- Used to set the thickness of the grid lines.
- Thickness level is from 1 to 5 by the pixel unit.
• GRID TRANS
- Used to set the transparency level of the grid
lines.
- [ON]: transparent
- [OFF]: opaque
• GRID THROUGHOUT
- Used to apply the currently selected GRID to
Through Out.
- [ON]: Applied to Through Out
- [OFF]: Not applied to Through Out
15
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[4] DISPLAY / VIDEO
DISPLAY/VIDEO 이
SCAN ZERO SCAN
ASPECT
H/V DELAY
BLUE ONLY
USER ASPECT HOR
USER ASPECT VER
3G FORMAT
H/V FLIP
ZOOM
ZOOM SPLIT
AUTO
OFF
OFF
NORMAL
OFF
OFF ▼
OFF
F-7HS
+1920
+1080
PAGE (1/2)
• SCAN
- Used to change the Scan mode.
- Available modes are ZERO SCAN, OVER SCAN,
PIXEL TO PIXEL, USER ASPECT.
* [PIXEL TO PIXEL] : When the resolution of the
input video is less than 1920 x 1080 such as
1280x720, NTSC, PAL, this function displays the
image pixel to pixel on the screen, not upscaling
it to 1920x1080.
* [USER ASPECT] : User can control the aspect ratio
by adjusting width and height of the display.
• ASPECT
- Used to change the Aspect Ratio.
- Regardless of the original Aspect ratio of the
input signal, the Aspect Modes are changed as
follow sequence. : [Auto][16:9][4:3][2.35:1][1.85:1]
[15:9][16:10][Anamorphic1.3x][Anamorphic1.5x]
[Anamorphic 1.8X] [Anamorphic 2.0X].
* [Auto] mode enables the Aspect Ratio of the
output signal to be synchronized to the original
Aspect Ratio of the input signal.
• H/V DELAY
- Used to monitor the Blanking area of H sync and
V sync.
• BLUE ONLY
- Available modes are [OFF] [BLUE ONLY] [MONO].
- [BLUE ONLY] : Remove red and green components
from the input signal and display blue componet
only.
- [MONO] : Used to remove the color(Chroma) from
the input signal and display the monochrome
component only.
16
• USER ASPECT HORIZONTAL/USER ASPECT
VERTICAL
- Activated only when the [SCAN] mode is set to
[User Aspect] .
- User can adjust the Horizontal and Vertical size
of the screen.
- See section “7. Other Functions [1] User Aspect”
for more information.
• 3G FORMAT
- Used to select 3G-SDI A/B input format.
[NORMAL]
[A 444 10BIT YCbCr], [A 444 10BIT RGB]
[A 444 12BIT YCbCr], [A 444 12BIT RGB]
[A 422 12BIT YCbCr], [B 444 10/12BIT YCbCr]
[B 444 10/12BIT RGB], [B 422 12BIT YCbCr]
[B 422 10BIT YCbCr 60P]
- In NORMAL MODE, automatically detected when
Payload signal is contained
• H/V FLIP
- Allows the displayed image to be flipped
horizontally or vertically.
- This feature provides flexible mounting options
for camera operators.
- Activates in the order : [H Flip]-[V Flip]-[H/V Flip]-
[AUTO]
- In the [AUTO] mode, the vertical FLIP operates
automatically according to the position of the
unit.
• ZOOM
- Used to magnify the image up to 90% on a pixel
basis and display on full screen.
- ZOOM range is 10% to 90% by 10% increment.
* ex) 10% Zoom : If the input signal’s resolution is
1920 x 1080, only 90% (1728(H) x 972(V)) of the
image would be shown on full screen without
the remaining 10% (192(H) x 108(V)) of the
image.
* See section “7. Other Functions -> [4] Zoom” for
more information.
• ZOOM SPLIT
- Used to magnify the image.
- Used to zoom the specified area sequentially.
- Designable areas are Left-Top, Right-Top, Left-
Bottom, Right-Bottom and Center.
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[4] DISPLAY / VIDEO
DISPLAY/VIDEO 이
DSLR SEL CANON 7D
DSLR SCALE
TIMECODE
FOCUS ASSIST
FOCUS AS COLOR
FOCUS AS LEVEL
SCR TALLY
SCR OP LEVEL
SCR TALLY COL
LOW BAT DIS
ARRI CAM STATUS
LDS INFO
INDEX LETTER
LIVE VIEW
OFF
OFF
RED
OFF
LOW
RED
OFF
OFF
OFF
OFF
F-7HS
+ 90
PAGE (2/2)
• DSLR SEL
- Select the DSLR camera to be used with the
monitor. Available mode is [CANON 7D].
* DSLR cameras’ screen size and aspect ratio of
Live / Record / Playback modes vary depending
to their manufacturer.
• DSLR SCALE
- This is a special function for CANON/NIKON DSLR
cameras.
- Used to scale the image with different resolution
as to the operation mode (Live View/ Record/
PlayBack) of the camera to fullfill the screen.
* See section “7. Other Functions [08] DSLR SCALE”
for more information.
• TIMECODE
- Used to set the Time Code.
- Available modes are VITC (UP), VITC (DOWN),
LTC (UP), LTC (DOWN).
• FOCUS ASSIST
- Focus Assist helps the shooters to easily find
out the exact area in the picture with good focus,
simply by adding colors on the shape or
boundaries of the object in the picture.
- Activates in order of [Mono On]-[Color On]-[Off].
* [Color On] : Only the boudary of the area with
good focus is displayed with the designated
color.
* [Mono On] : The boundary of the area with good
focus is colored with the designated color, while
the rest of the areas(pixels) have only Y’(Luma)
signals to be black & white image.
* See section “7. Other Functions [6] Focus Assist”
for more information.
• FOCUS AS COLOR (Focus Assist Color)
- Used to select a color for Focus Assist among
RED, GREEN, BLUE, WHITE.
- This feature is available only when the Focus
Assist mode is activated.
• FOCUS AS LEVEL (Focus Assist Level)
- Used to set the edge difference value between
the edges in an image.
- Available values are from 0 to 100. Larger
the value the more sophisticated the detail
detection.
- Designated color is displayed when the
difference of the edges exceeds the
previously set value.
- This feature is available only when the FOCUS
ASSIST mode is activated.
17
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[4] DISPLAY / VIDEO
DISPLAY/VIDEO 이
DSLR SEL CANON 7D
DSLR SCALE
TIMECODE
FOCUS ASSIST
FOCUS AS COLOR
FOCUS AS LEVEL
SCR TALLY
SCR OP LEVEL
SCR TALLY COL
LOW BAT DIS
ARRI CAM STATUS
LDS INFO
INDEX LETTER
LIVE VIEW
OFF
OFF
RED
OFF
LOW
RED
OFF
OFF
OFF
OFF
F-7HS
+ 90
PAGE (2/2)
• SCR TALLY (Screen Tally)
- Used to set Tally operation according to the
input level of TALLY IN terminal which is among
the terminals of XLR 4P connector in the rear.
• SCR OP LEVEL (Screen Tally Operation Level)
- Used to set the input level of Tally operation.
(Open&Low : less than 0.6V, High Range : 5V±2.5V)
- High : Set the level as “High” to activate the Tally
and set the level as “Low” to inactivate the Tally.
- Low : Set the level as “Low” to activate the Tally
and set the level as “High” to inactivate the Tally.
• SCR TALLY COL (Screen Tally Color)
- Used to set Tally color.
- Available colors are Red, Green and Yellow.
• LOW BAT DIS (Low Battery Display)
- Used to set Low Battery Display function.
- When the battery becomes weak, [Low Battery]
sign is indicated on the OSD.
• ARRI CAM STATUS (Arri Camera Status)
- Used to display the camera status information
provided by ARRI ALEXA camera on the OSD.
- When the Arri Cam Status is activated, the screen
is squeezed to the 1742 x 980 resolution.
• LDS INFO (Lens Data System Information)
- Used to se set the information display of the Lens
Data System.
• INDEX LETTER
- Used to set the monitor identification character
notation in the upper right corner of the screen.
18
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[5] WAVEFORM
WAVEFORM
ENABLE
TYPE
INTENSITY
TRANS
SIZE
LINE WAVEOFORM
SEL LINE POS
LUMA CHECK
LUMA ADJUST
RANGE ERROR
Y MAX
Y MIN
C MAX
C MIN
Y PICTURE BLINK
C PICTURE BLINK
OFF
OFF
OPAQUE
SAMLL
OFF
OFF
OFF
OFF
OFF
F-7HS
1
• ENABLE
- Used to activate/ deactivate the Waveform
which is selected in TYPE menu.
• TYPE
- This function sets the Waveform and Vectorscope.
- Available options are different according to the
Input signal.
- Activates in the order: Waveform - Vectorscope -
Waveform Wide - Waveform YCbCr -
Waveform RGB - Wave Vector - YCbCr Vector -
Full Waveform - Full Vector - Off.
• INTENSITY
- Used to set the brightness level of the Waveform/
Vectorscope display from 1 to 63.
- The higher the number the brighter the
waveform will be.
• TRANS (Transparency)
- Used to select the transparency option of the
Waveform / Vectorscope between [OPAQUE]
and [TRANS].
- Even though the option is set to [Opaque], it
will automatically turn to [Trans] when the
main OSD overlaps the waveform/vectorscope.
And turns back to [Opaque] when the main OSD
disappears.
0
0
0
0
0
0
• SIZE
- Adjust the size of the Waveform or Vectorscope.
- Available options are [SMALL] and [LARGE].
* See section “7. Other Function [2] Waveform/
Vectorscope“ for more information.
• LINE WAVEFORM
- This item is utilized to display the one line data
on the Waveform.
• SEL LINE POS (Select Line Position)
- Used to select specific horizontal line for
Waveform / Vectorscope.
- This is available when LINE Waveform is activated.
- Use the Knob to select a desired vertical line.
- Control range varies according to the resolution
of the input SDI signal.
* PAL : Min. 1, Max. 625
* NTSC : Min. 1, Max. 525
* 720p : Min. 1, Max. 750
* 1080i : Min. 1, Max. 1125
* 1080p : Min. 1, Max. 1125
• LUMA CHECK
- Analyzes the Luma(Y’) level of the input image
and displays the selected zone on the screen.
- Available modes are [Color Pattern] and
[Zebra Pattern].
- After each pixel’s Y’ level is analyzed, it is
displayed as a certain color or zebra pattern
according to the Index on the right side of the
screen.
- When a pixel’s Y’ level is under 0%(16), the pixel
is displayed as green color or green diagonal
lines, and over 100%(235) as red color or red
diagonal lines.
- When the Y’ level of a pixel is between 0~100%,
the pixel is displayed as Gray level, except for
selected Luma Zone.
- In the [Color Pattern] mode, the zone the user
adjusted is displayed as Yellow (10% lower zone),
Pink (±2.5%), Cyan (10% upper zone).
- In the [Zebra Pattern] mode, ±5% of the selected
Y’ Level will be displayed as diagonal lines.
19
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[5] WAVEFORM
WAVEFORM
ENABLE
TYPE
INTENSITY
TRANS
SIZE
LINE WAVEOFORM
SEL LINE POS
LUMA CHECK
LUMA ADJUST
RANGE ERROR
Y MAX
Y MIN
C MAX
C MIN
Y PICTURE BLINK
C PICTURE BLINK
OFF
OFF
OPAQUE
SAMLL
OFF
OFF
OFF
OFF
OFF
F-7HS
1
• LUMA ADJUST
- Used to set the Y’ level to be colored Yellow, Pink
and Cyan in [Color Pattern] mode, or to set Y’
level zone to be displayed with diagonal lines in
[Zebra Pattern] mode simply by scrolling the
Knob.
- Available values are 0% ~ 100%.
* See section “7. Other Function [5] Luma(Y’) Zone
Check” for more information.
• RANGE ERROR
- Used to set whether or not to activate Y MAX,
Y MIN, C MAX, C MIN, Y PICTURE BLINK and C
PICTURE BLINK functions.
- The values of Y MAX, Y MIN, C MAX, C MIN are
indicated in Waveform/Vectorscope.
- If [Y PICTURE BLINK] or [C PICTURE BLINK] is
enabled, the section of image that exceeds the
selected values of Y MAX, Y MIN, C MAX and C
MIN shall blink.
* See section “7. Other Function [7] Range Error”
for more information.
0
0
0
0
0
0
• Y MAX
- Used to set the maximum Luma(Y’) level from 0
to 255.
- Pixels with values exceeding the maximum
luma(Y’) level blink on the screen, and are
displayed in red on the Waveform.
• Y MIN
- Used to set the minimum Luma(Y’) level from 0
to 255.
- Pixels with values below the minimum luma(Y’)
level blink on the screen, and are displayed in
red on the Waveform.
• C MAX
- Used to set the maximum chroma(C’) level from
0 to 255.
- Pixels with values exceeding the maximum
chroma(C’) level blink on the screen, and are
displayed in red on the Waveform.
• C MIN
- Used to set the minimum chroma(C’) level from
0 to 255.
- Pixels with values below the minimum chroma(C’)
level blink on the screen, and are displayed in red
on the Waveform.
• Y PICTURE BLINK
- Used to set whether or not to blink pixels with
values exceeding Y MAX and Y MIN.
• C PICTURE BLINK
- Used to set whether or not to blink pixels with
values exceeding C MAX and C MIN.
20
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[6] AUDIO
AUDIO
VOLUME
Em. AUD LEFT
Em. AUD RIGHT
LEVEL METER
ALM DISPLAY
ALM REFERENCE
ALM SIZE
PEAK DECAY TIME
CH 01
CH 02
OFF
PAIR
-18 dB
SMALL
F-7HS
+ 15
+ 10
• VOLUME
- Used to control the output volume for the
[AUDIO OUT] on the side of the monitor.
- Control range is from 0 to 30.
• Em. AUD LEFT (Audio Left)
- Used to set embedded audio channel for left
audio out of [AUDIO OUT] terminal on the side
of the monitor.
- Available options are [CH 01] to [CH 16].
* In the HDMI mode, Left is set to [CH 01].
• Em. AUD RIGHT(Audio Right)
- Used to set embedded audio channel for right
audio out of [AUDIO OUT] terminal on the side
of the monitor.
- Available options are [CH 01] to [CH 16].
*In the HDMI mode, RIGHT is set to [CH 02].
• LEVEL METER
- Used to set the Level Meter for the embedded
audio.
- Available options are :
SDI Input : [Off]-[16CH(Hor.)]-[16CH(Ver.)]
HDMI Input: [Off]-[2CH(Hor.)]-[2CH(Ver.)]
* 16 CH(HOR.) : Displays 8 channels on top
left and 8 channels on top right of the screen
horizontally.
* 16 CH(VER.) : Displays 8 channels on center
left and 8 channels on top right of the screen
vertically.
* In the HDMI mode, only 2 channels are displayed.
• ALM DISPLAY (Audio Level Meter Display)
- Used to set the display method for audio level
meter.
- Available modes are [GROUP] and [PAIR].
* In the HDMI mode, the mode is set to [PAIR].
• ALM REFERENCE (Audio Level Meter Reference)
- Display the default audio level meter value,
- Available options are -18dB and -20dB.
- Audio level meter within selected value turns to
green and exceeded audio level is displayed in
yellow.
- Audio level exceeding -4dB is displayed in red.
• ALM SIZE (Audio Level Meter Size)
- Used to control the size of the audio level meters.
- Available options are [SMALL] and [LAGRE].
• PEAK DECAY TIME
- Sets the reduction time for max value indication
of audio signals.
- Control range is from MIN 0 to MAX 100. Bigger
number means a longer display time for max
value.
21
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[7] SYSTEM
SYSTEM
DEFAULT
LUMINANCE
INTERNAL PAT
DISPLAY ENABLE
ECO SAVING
AUTO COOL
POWER LED
EXTERNAL FAN
SW UPGRADE
PRESET SAVE
PRESET LOAD
VERSION
SERIAL NUM
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
SW 23 FPGA 04 BD 01
M9270506
F-7HS
+ 8
• DEFAULT
- Used to initialize OSD values to factory default.
- Available modes are DEFALUT and FACTORY.
- In the DEFALUT mode, except for the stored 3D
LUT, all values are initialized.
- In the FACTORY mode, all values are initialized to
factory default.
• LUMINANCE
- Used to indicate the current Luminance value .
- In the case of System Default, the value returns
to factory default(after color calibration).
- Available values are from 1 to 200.
• INTERNAL PAT (INTERNAL PATTERN)
- Generates Color Bar+Pludge and Grayscale
Pattern internally.
- Selectable range for Gray Pattern is from 0% to
100% with 5% increment.
* See section “7. Other Function -> [11] Internal
Pattern” for more information.
• DISPLAY ENABLE
- Used to set the LUMINANCE to the minimum
value when the time set in the still image output
is exceeded.
- When video is output or the MENU button is
pressed, the LUMINANCE is reset to the original
value.
- Settable options are ON, 5 MIN, 10 MIN, 20 MIN
and 30 MIN.
- In the Function Key, the screen can be turned
ON/OFF immediately by user’s choice.
• ECO SAVING
- Used to save power consumption automatically
when there is no monitor signal.
- When the signal is supplied, the brightness of
the monitor will be changed to the set value.
22
FHD Hight Bright Field Monitor
05 MENU OPERATIONS
[7] SYSTEM
SYSTEM
DEFAULT
LUMINANCE
INTERNAL PAT
DISPLAY ENABLE
ECO SAVING
AUTO COOL
POWER LED
EXTERNAL FAN
SW UPGRADE
PRESET SAVE
PRESET LOAD
VERSION
SERIAL NUM
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
SW 23 FPGA 04 BD 01
M9270506
F-7HS
+ 8
• AUTO COOL
- If [AUTO COOL] is set ON, the brightness mode is
automatically changed to cool down the monitor
and protect the hardware when the internal
temperature is increased to the particular level.
- When the temperature detected on the main
board reaches 75°C (167°F), the MAX BRIGHTNESS
mode is automatically changed to INDOOR mode.
And, 'MONITOR TOO HOT' and 'CHANGE TO INDOOR'
warning signs appear on the screen alternately.
When these warning signs appear, the MAX
BRIGHTNESS mode cannot be selected.
- When the internal temperature detected on the
main board goes down to 64°C (147°F), the
warning signs disappear and the MAX BRIGHTNESS
mode can be selected.
• POWER LED
- Used to turn on or off the Power LED on the back
of the monitor.
- [ON]: When the monitor power is on, the Power
LED on the back turns green.
- [OFF]: When the monitor power is on, the power
LED on the back turns off.
• EXTERNAL FAN
- When [EXTERNAL FAN] mode is set ON, the USB
port outputs the 5V power, which allows the
external fan attached on the monitor to receive
the power for the fan operation.
• S/W UPGRADE
- Used to upgrade the firmware using USB
(Thumb drive).
* See section “7. Other Functions -> [14] Firmware
Upgrade” for more information.
• PRESET SAVE
- Available values are from PRESET 01 to PRESET 04.
- Used to save the current settings in the PRESET
position.
• PRESET LOAD
- Available values are from PRESET 01 to PRESET 04.
- Used to load the settings saved in PRESET 01 to
PRESET 04.
• VERSION
- Displays current firmware version.
• SERIAL NUM (Serial Number)
- Displays the serial number of the monitor.
23
FHD Hight Bright Field Monitor
06 BUTTON FUNCTIONS
MENU <EXIT> BUTTON / KNOB BUTTON
[1] MENU <EXIT> BUTTON
SDI A
HDMI
1920 x 1080 50p
• F-7HS unit is capable of processing SDI/
HDMI Input Signal.
1. Press the [MENU<EXIT>] button on the top of
the monitor for more than 2 seconds and
activate the input selection menu as shown
above.
2. The resolution of the input video is displayed
on the bottom of the OSD screen.
3. Press the [MENU<EXIT>] button again to remove
the OSD menu from display.
* If no image displays after selecting the desired
input mode, check and make sure that your
connection is not lost or disconnected.
[2] KNOB BUTTON
VOLUME
BRIGHTNESS
CONTRAST
CHROMA
SHARPNESS
+ 15
+ 0
+ 0
+ 0
+ 0
PEAKING BOOST
+ 0
• F-7HS monitor supports the HOT KEY input.
1. Press the [Knob] button on the top of the
monitor for more than 2 seconds and activate
the settings adjustment menu as shown above.
Move to a desired menu with the Knob and
press the Knob to select.
The mode changes in this order: VOLUME →
BRIGHTNESS → CONTRST → CHROMA →
SHARPNESS → PEAKING BOOST
2. Adjust the set value by rotating the Knob.
3. Press the [MENU<EXIT>] on the top of the
monitor again to remove the OSD menu from
display.
24
FHD Hight Bright Field Monitor
06 BUTTON FUNCTIONS
FUNCTION BUTTON
[3] FUNCTION BUTTON
F1 FUNC.SEL
SCAN
ASPECT
MARKER
H/V DELAY
BLUE ONLY
ZOOM
ZOOM SPLIT
FREEZE
DSLR SCALE
AUDIO LVM
TIME CODE
FOCUS ASSIST
WAVEFORM
LUMA(Y`) ZONE
RANGE ERROR
H/V FLIP
MAX BRIGHTNESS
CAMERA LUT
DISPLAY ENABLE
INPUT SELECT
ARRI METADATA
EXTERNAL FAN
GRID
3D LUT LOAD
• Used to make a quick setting of the Function Key.
1. Press the function button(F1~F3) on the top of
the monitor for more than 2 seconds and
activate the OSD menu as follows.
2. Move to a desired function with the Knob and
press the Knob to select.
3. Once the function is set, press the Function
button(F1~F3) to activate the function.
25
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[1] USER ASPECT
• Used to adjust the Width /Height display ratio.
1. There are two ways activate [USER ASPECT] mode.
- Go to MENU → DISPLAY/VIDEO → SCAN and select the [USER ASPECT] mode.
- Assign [ASPECT] mode to one of the Function button, press the Function button and select the
[USER ASPECT] mode.
2. After the activation, press the Knob to begin controlling. Adjust the ratio using the knob.
USER ASPECT
WIDTH +1920
HEIGHT +1080
- Adjust the ratio using the Knob (UP / DOWN).
- Control range for width: 0~1920.
- Control range for height : 0~1080.
- The size-adjusted picture always stays in the center of the screen.
- The size can be adjustable with 2 increment and decrement.
26
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[2] WAVEFORM / VECTORSCOPE
• WAVEFORM Y
- Displays the Luma(Y’) component of the input signal into waveform.
• The Waveform/ Vectorscope function can be
used only when the input signal is YUV.
• In the case of RGB input, Waveform RGB is supported.
• Available modes in the YUV signal:
- Waveform
- Vectorscope
- Waveform Wide
- Waveform YCbCr
- Waveform RGB
- Wave_Vector
- YCbCr Vector
- Full Waveform
- Full Vector
• WAVEFORM Cb, Cr
- Displays the Cb, Cr components of the input signal into waveform.
• VECTORSCOPE
- Displays the color components ‘B-Y’ and ‘R-Y’ of the input signals onto the X-Y axis.
- Two different types of Vetorscopes are displayed according to SD or HD input signals.
- 100% and 75% scales are indicated on the Vetorscope.
100%
75%
27
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[3] LINE SELECT (WAVEFORM / VECTORSCOPE)
• Used to select specific Vertical Line for WaveForm / VectorScope.
- This is available when LINE WaveForm is activated.
- To activate this feature, set [WAVEFORM] - [LINE WAVEFORM] - [ON], and select the desired horizontal
line using the KNOB in [SEL LINE POS].
- Control range varies according to the resolution of the input SDI signal.
* PAL : 0~625
* NTSC : 0~525
* 720p : 0~750
* 1080 i/p : 0~1125
- Control range for HDMI signal varies according to the output resolution of the signal.
* Selected line is indicated on the screen.
LINE POSITION
28
07 OTHER FUNCTIONS
[4] ZOOM
• Used to magnify the input signal from 0% to 90%.
• Supports Zoom Width Scroll / Zoom Height Scroll function.
• Zooms IN/OUT focused on the scrolled area.
ZOOM 0FF
WIDTH + 0
HEIGHT + 0
<ZOOM OFF>
FHD Hight Bright Field Monitor
<ZOOM 30%>
• When the image is zoomed up, you can move the zoomed image vertically and horizontally with the
zoom-up rate maintaining.
ZOOM 30%
WIDTH + 0
HEIGHT + 0
ZOOM 30%
WIDTH - 70
HEIGHT - 100
29
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[5] LUMA (Y') ZONE CHECK
• COLOR PATTERN TYPE
- Displays the pixels with the designated
Luma(Y’) levels of the input image in colors.
Pixels whose Y’ level is over 100% are displayed
as Red.
Pixels whose Y’ level is below 0% are displayed
as Green.
- Pixels with Y’ levels which are designated by the
user are displayed in following colors - yellow,
pink, cyan.
- Factory Default Y’ (Border line between pink and
yellow) level is 70%. The upper 2.5% and lower
2.5% zone from the Y’ level set in [LUMA(Y’)
ZONE ADJUST] menu is displayed in Pink.
The upper 10% zone from the Pink zone is
displayed in Yellow, and the lower 10% zone
from the Pink zone is displayed in Cyan. So, 25%
zone is displayed in colors and the other 75%
zone is displayed mono and white.
• LUMA(Y’) ZONE CHECK function is convenient
to set the exposure or the lighting so that the
skin tone or the specific color tone is correctly
shot.
• ZEBRA PATTERN TYPE
- Displays the pixels with the designated
Luma(Y’) levels of the input image in zebra
pattern. Pixels whose Y’ level is over 100% are
displayed as red diagonal stripes.
Pixels whose Y’ level is below 0% are displayed
as green diagonal stripes.
- Pixels with Y’ levels which are designated by the
user are displayed as black diagonal stripes.
- Factory Default Y’ level is 70%. The pixels with Y’
level from 65% to 75% are displayed as black
zebra pattern.
So, totally 10% zone is displayed as black
diagonal stripes.
<Luma Zone Check OFF>
<Luma Zone Check ON_Zebra Pattern Type>
30
<Luma Zone Check ON_Color Pattern Type>
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[6] FOCUS ASSIST
• Focus Assist function assigns a color on the pixels of the shape or boundary of the image, which
helps the user easily see which part of the image is in focus or out of focus.
- With this function, the user can easily differentiate the focused area from the out-focused area
especially when shooting with a shallow depth of field.
- Available types are [COLOR ON] and [MONO ON].
• [COLOR ON]: Background image is original color type.
• [MONO ON]: Background image is mono type.
<FOCUS ASSIST - COLOR ON> <FOCUS ASSIST - MONO ON>
31
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[7] RANGE ERROR
• Pixels with Y’ or C’ levels exceeding the designated levels of Y MAX, Y MIN, C MAX and C MIN shall blink.
- Analyzes the input signal’s Luma(Y’) and chroma information(C’) and if the input signal exceeds the
designated minimum value and maximum value, the pixel shall blink. This function is to help the user to
easily find out any unwanted level of signals and for a better exposure setting.
* In the case of RGB input, Range Error is not supported.
<Range Error OFF> <Range Error ON>
32
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[8] DSLR SCALE
• This function is designed for some DSLR cameras of Canon(7D) that output different resolution from
the operation mode (StandBy, Record, Play Back)
• Select the Camera model in the [Display/Vide]- [DSLR Camera Sel.] menu.
• CANON (5D/550D)
- In StandBy mode of Canon 5D Mark II, 1080i of HD resolution is indicated. However, real output resolution
is 1620x1080 so blank area is displayed on the screen because the 16:9 aspect ratio is not realized.
- In this case, use DSLR SCALE function to enlarge the 1920x1080 image and display full screen.
- In Recording mode of CANON 5D Mark II, the output resolution is SD(480p).
- Although it is SD, the real output resolution is 640x390 not 720x480.
- DSLR SCALE function scales the 640×390 image to 1280x800(panel resolution) and display full screen.
※
Note
1. When you compare the circle chart or the camera shooting chart with DSLR connected monitor(HDMI)
and HDMI to SDI Conversion connected monitor, The function of Live/Rec 16:9 mode should be selected
to compare circle and it is equal to its actual. If the circle is compared in Live/Rec Full mode, the output
of the circle is deformed.
2. Both the DSLR Camera connected monitor and HDMI to SDI Conversion connected monitor should be
compared to circle in Zeroscan mode. It is deformed if user selects in Overscan and Underscan mode.
<DSLR Scale Off> <DSLR Scale On>
33
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[9] HDMI To SDI CONVERSION-OUT / SDI To HDMI CONVERSION-OUT
HDMI TO SDI CONVERSION-OUT
• Video source from ‘HDMI input’ terminal can be
output through ‘SDI throughout’ terminal.
SDI TO HDMI CONVERSION-OUT
• 3G/HD/SD SDI signals from ‘SDI input’ terminal
can be output through ‘HDMI out’ terminal.
Output
Format
Input
Format
480/59.94i
576/50i
480/60p
576/50p
720/50p
720/59.94p
720/60p
1080/50i
1080/59.94i
1080/60i
1080/24p
1080/25p
1080/30p
1080/50p
1080/59.94p
1080/60p
1080/50p
●
●
1080/60p
●
●
Converted out in the same format as the input format
480/59.94i
576/50i
720/50p
720/59.94p
720/60p
1080/50i
1080/59.94i
1080/60i
1080/24p
1080/25p
1080/30p
1080/24psF
1080/50p
1080/59.94p
1080/60p
1080/50p
●
●
●
●
●
1080/60p
●
●
●
●
●
●
●
●
●
●
※
Note : DSLR camera manufacturers usually specify the resolution and frame rate for the recording.
The signal format that is output through HDMI terminal of cameras may differ from makers to makers.
The signal format for HDMI output and playback function of Canon DSLRs is 59.94i. And even though
60i or 60p is specified in the specification of the cameras, the actual recording or HDMI output format
would be 59.94i or 59.94p.
34
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[10] SCREEN TALLY / REAR TALLY
• Activates with the Rear Tally on the rear of the monitor at the same time.
• Screen TALLY On/Off
- Used to set Tally operation according to the input level of TALLY IN terminal which is among the terminals
of XLR 4P connector in the rear.
• Screen TALLY Operating Level
- Used to set the input level of Tally operation. (Open&Low : less than 0.6V, High : more than 2.5V)
- High : Set the level as “High” to activate the Tally and set the level as “Low” to inactivate the Tally.
- Low : Set the level as “Low” to activate the Tally and set the level as “High” to inactivate the Tally.
• Screen TALLY Color
- Used to set Tally color.
- Available colors are Red, Green and Yellow.
<Screen TALLY ON>
35
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[11] INTERNAL PATTERN
• Displays internally generated test patterns.
- The pattern consists of Color Bar + Pluge pattern and Grayscale patterns.
Full screen colors of various gray levels (0~100%) are also embedded.
<Color Bar + Pluge Pattern> <Gray Pattern>
36
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[12] ARRI CAM STATUS
• Used to display the camera status information provided by ARRI ALEXA camera on the OSD.
- Displays the information in the order: [Project FPS]-[Exposure Time]-[White Balance]-[White Balance CC]-
[Camera Index Letter] / [Lens Name]-[Focal Length]-[Iris]-[Focus Distance] / [Lens Squeeze Factor]-[Scene]
- When the Arri Cam Status is activated, the screen will be scaled to 1742 x 980.
<ARRI CAM Status On>
37
FHD Hight Bright Field Monitor
07 OTHER FUNCTIONS
[13] MAX BRIGHTNESS
• This function sets the brightness of the panel.
• Available values are below :
- INDOOR : 100 nits
- OUTDOOR : 1500 nits
- MAXIMUM : 1800 nits
[14] FIRMWARE UPGRADE
• The USB(Thumb drive) which contains the F/W file is needed for Firmware Upgrade.
• Select the SW UPGRADE in the SYSTEM menu.
1. Connect the USB to the USB Slot on the bottom of the monitor.
2. Go to [MENU] → [SYSTEM] → [SW UPGRADE], and select what to update among ALL, CPU, FPGA, IMAGE.
3. When the USB connection is completed, the S/W upgrade starts and the progress displays on the
bottom left side of the screen.
4. If the USB doesn’t connect properly or there is no file in the specified location, the error message will
be displayed on the bottom left side of the screen and the upgrade won’t start.
5. In that case, check the USB or the file location and try again.
• After USB connection, turn off and then on the monitor.
38
FHD Hight Bright Field Monitor
08 AVAILABLE SIGNAL FORMATS
VIDEO
PC
INPUT SIGNAL
1080 / 50i
1080 / 50p
1080 / 59.94i
1080 / 60i
1080 / 59.94p
1080 / 60p
640 x 400 (70Hz)
640 x 480 (60Hz)
640 x 480 (75Hz)
800 x 600 (60Hz)
800 x 600 (75Hz)
1024 x 768 (60Hz)
1024 x 768 (70Hz)
1024 x 768 (75Hz)
1280 x 768 (60Hz)
1280 x 800 (60Hz)
1280 x 1024 (60Hz)
1920 x 1080 (60Hz)
480 / 59.94i (NTSC)
480 / 60p
576 / 50i (PAL)
576 / 50p
720 / 23.98p
720 / 24p
720 / 25p
720 / 30p
720 / 50p
720 / 59.94p
720 / 60p
1080 / 23.98PsF
1080 / 24PsF
1080 / 25PsF
1080 / 23.98p
1080 / 30PsF
1080 / 29.97PsF
1080 / 24p
1080 / 25p
1080 / 29.97p
1080 / 30p
DISPLAY CHARACTER EXAMPLE
1920x1080 50i
1920x1080 25p
1920x1080 60i
1920x1080 60i
1920x1080 60p
1920x1080 60p
640x400 70p
640x480 60p
640x480 75p
800x600 60p
800x600 75p
1024x768 60p
1024x768 70p
1024x768 75p
1280x768 60p
1280x800 60p
1280x1024 60p
1920x1080 60p
720x480 60i
720x480 60p
720x576 50i
720x576 50p
1280x720 24p
1280x720 24p
1280x720 25p
1280x720 30p
1280x720 50p
1280x720 60p
1280x720 60p
1920x1080 48i
1920x1080 48i
1920x1080 50i
1920x1080 24p
1920x1080 60i
1920x1080 60i
1920x1080 24p
1920x1080 25p
1920x1080 30p
1920x1080 30p
SDI
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
HDMI
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
39
FHD Hight Bright Field Monitor
09 VIDEO SUPPORT RESOLUTION
INPUT SIGNAL INTERFACES SIGNAL FORMAT (SD SDI)
SD SDI single link
720x487 (59.94i)
720x576 (50i)
INPUT SIGNAL INTERFACES SIGNAL FORMAT (HD SDI)
HD SDI single link
1920x1080
(23.98/24/25/29.97/30p)
(50/59.94/60I)
(24/25/29.97/30psf)
1280x720
(50/59.94/60p)
INPUT SIGNAL INTERFACES SIGNAL FORMAT (3G SDI)
1920x1080 (60p/59.94p/50p)
3G-SDI (A/B) single link
1920x1080
(30/29.97/25/24/23.98/
30sF/29.97sF/25sF/24sF/23.98sF)
INPUT SIGNAL INTERFACES SIGNAL FORMAT (HDMI/DP)
HDMI single link
1080p (60/59.94/50/30/29.97/25/24/23.98)
1080i (60/59.94/50)
720p (50/59.94/60p)
480i (60) / 576i (50)
480p (60) / 576p (50)
YCbCr 4:2:2 10bit
YCbCr 4:2:2 10bit
YCbCr 4:2:2 10bit
RGB 4:4:4 10bit / 12bit
YCbCr 4:4:4 10bit / 12bit
RGB 4:4:4 8bit / 10bit / 12bit
YCbCr 4:4:4 8bit / 10bit / 12bit
YCbCr 4:2:2 8bit / 10bit / 12bit
40
10 PRODUCT SPECIFICATIONS
FHD Hight Bright Field Monitor
LCD
Input
Output
Specifications
Input Signal
SDI Input Signal
Formats
SMPTE ST-274M
SMPTE ST-296M
SMPTE ST-125M
ITU-R BT.656
1 x USB Update
Audio In
Audio Out
Power
Power Consumption (Approx.)
Operating Temperature
Storage Temperature
Dimensions
Main Body
Shipping Box
Weight
Basic Accessories
Optional Accessories
Size
Resolution
Pixel Pitch
Color Depth
Viewing Angle
Luminance of white
Contrast Ratio
Display Area
1 X HDMI
1 X BNC
1 X HDMI
1 X BNC
3G-SDI
HD-SDI
SD-SDI
HDMI
SMPTE ST-425M-A/B
F-7HS
7”
1920×1200 (16:10)
0.07875(H) X 0.07875(V) mm
1.073B Colors (10 bit)
160°(H) / 160°(V)
1800 nits(Max)
1200 : 1
151.2(H) X 94.5(V) mm
HDMI Input
3G/HD/SD SDI Input
HDMI Output (HDMI loop out, SDI-to-HDMI Conversion output)
3G/HD/SD SDI Output (SDI loop out, HDMI-to-SDI Conversion output)
2.970 Gb/s
1.485 Gb/s
270 Mb/s
480i / 480p / 576i / 576p / 720p / 1080i / 1080p
1080p (60/59.94/50/30/29.97/25/24/23.98/30sF/29.97sF/25sF/24sF/23.98sF)
1080i (60/59.94/50)
1080i (60/59.94/50)
1080p (30/29.97/25/24/24sF/23.98/23.98sF)
720p (60/59.94/50)
480i (59.94)
576i (50)
USB A type, Firmware Upgrade
SDI Embedded Audio (Group, Ch Selectable)
External Output Port (3.5m Phone Jack)
DC 6V ~ 34V
21W(Max)
0 ℃ to 40 ℃ (32
℉
to 104
℉
)
-20 ℃ to 60 ℃ (-4
℉ to 140
℉ )
211 x 125 x 28.3mm (8.3 x 4.95 x 1.11 inch)
290 X 158 X 83mm (11.42 X 6.22 X 3.27 inch)
0.76kg / 1.67lbs
D-Tap-C Cable, Camera Mount
External Acrylic Protector, Sun Hood, D-Tap Power Cable, Battery Bracket,
V-Mount Battery Bracket, Anton-Bauer(Gold) Battery Bracket, Carrying Case,
DC Adapter, HDMI Bracket
* The specification above may be changed without notice.
41
FHD Hight Bright Field Monitor
11 OPTIONAL ACCESSORIES
Model Product Description
OPT-AF-F-7H External Acrylic filter for F-7H / F-7HS
Hood-F-7H Sun Hood for F-7H / F-7H mk2 / F-7HS
HDMI BKT-F7H HDMI Bracket for F-7H / F-7H mk2 / F-7HS
TH-Mount-F7H
Camera Mount for F-7H / F-7H mk2 / F-7HS
(Screw head length 20mm)
V-Mount-F7H-C
Battery Adapter for F-7H / F-7H mk2 / F-7HS/ F-10A
(Cost effective)
V-Mount-F7H
Battery Adapter for F-7H / F-7H mk2 / F-7HS/ F-10A
(IDX V-Mount Plate)
42
11 OPTIONAL ACCESSORIES
Model Product Description
AB-mount-F7H (AP)
G-Mount-F7H (EMEA)
Anton-Bauer(Gold) Battery Adapter for
F-7H / F-7H mk2 / F-7HS / F-10A
FHD Hight Bright Field Monitor
D-Tap-C cable
D-Tap-S cable
D-Tap-L cable
D-Tap Adapter for VFM-056WP, 058W, 055A
& LVM-074, 070C, 075A / SRM-074W(-N)
/ F-7H / F-7H mk2 / F-7HS / F-10A
(Coil Type)
D-Tap Adapter for VFM-056WP, 058W, 055A
& LVM-074, 070C, 075A / SRM-074W(-N)
/ F-7H / F-7H mk2 / F-7HS / F-10A
(Short - 17" length)
D-Tap Adapter for VFM-056WP, 058W, 055A
& LVM-074W, 070C, 075A / SRM-074W(-N)
/ F-7H / F-7H mk2 / F-7HS / F-10A
(Long - 29" length)
BB-F7H-S
Battery Bracket for F-7H / F-7H mk2 / F-7HS / F-10A
(Sony NP-F770/F970)
BB-F7H-C
Battery Bracket for F-7H / F-7H mk2 / F-7HS / F-10A
(Canon BP Series)
43
FHD Hight Bright Field Monitor
11 OPTIONAL ACCESSORIES
Model Product Description
BB-F7H-P
Battery Bracket for F-7H / F-7H mk2 / F-7HS / F-10A
(Panasonic CGA/VB Series)
BB-F7H-U
Battery Bracket for F-7H / F-7H mk2 / F-7HS / F-10A
(Sony BP-U30/U60)
BB-F7H-E
Battery Bracket for F-7H / F-7H mk2 / F-7HS / F-10A
(Canon LP-E6 Series, DSLR EOS 5D/7D)
BB-F7H-B
Battery Bracket for F-7H / F-7H mk2 / F-7HS / F-10A
(Panasonic AF-100)
44
F-7HS
Advertisement
