Delta 28-560 User manual

16" Wood-Metal Cutting
| Band Saw
(Model 28-560)
The Serial No./Model No. plate is
attached to the back side of the saw on
the frame casting. Record the Serial
No. and Model No. as stamped on this
plate and the date of purchase for your
future reference.
Serial No.
Model No.
Date of Purchase
For Your Own Safety,
Read Instruction Manual
Before Starting Operations
DATED 10-12-95 PART NO. 419-96-651-0002
© Delta International Machinery Corp. 1995
ADELTA
TVNANVIN NOILONYHLSNI
SAFETY RULES
‘Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain
hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the
possiblity of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may
result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection
can reduce your potential for injury. But even the best guard won't make up for poor judgment, carelessness or inattention. Always
use common sense and exercise caution in the workshop. If a procedure feels dangerous, don't try it. Figure out an alternative
procedure that feels safer. REMEMBER: Your personal safety is your responsibility.
This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not be modified
and/or used for any application other than that for which it was designed. If you have any questions relative to a particular
application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the
product.
DELTA INTERNATIONAL MACHINERY CORP.
MANAGER OF TECHNICAL SERVICES
246 ALPHA DRIVE
PITTSBURGH, PENNSYLVANIA 15238
(IN CANADA: 644 IMPERIAL ROAD, GUELPH, ONTARIO N1H 6M7)
WARNING: FAILURE TO FOLLOW THESE RULES
MAY RESULT IN SERIOUS PERSONAL INJURY
1. FOR YOUR OWN SAFETY, READ INSTRUCTION
MANUAL BEFORE OPERATING THE TOOL. Learn the
tool's application and limitations as well as the specific hazards
peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PROTECTION.
4. GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole electrical
receptacle. If an adapter is used to accommodate a two-prong
receptacle, the adapter lug must be attached to a known
ground. Never remove the third prong.
5. REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches are
removed from tool before turning it “on.”
6. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
7. DON'T USE IN DANGEROUS ENVIRONMENT. Don't
use power tools in damp or wet locations, or expose them to
rain. Keep work area well-lighted.
8. KEEP CHILDREN AND VISITORS AWAY. All children
and visitors should be kept a safe distance from work area.
9. MAKE WORKSHOP CHILDPROOF - with padlocks,
master switches, or by removing starter keys.
10. DON'T FORCE TOOL. It will do the job better and be safer
at the rate for which it was designed.
11. USE RIGHT TOOL. Don't force tool or attachment to do
a job for which it was not designed.
12. WEAR PROPER APPAREL. No loose clothing, gloves,
neckties, rings, bracelets, or other jewelry to get caught in
moving parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
13. ALWAYS USE SAFETY GLASSES. Wear safety glasses
(must comply with ANSI Z87.1). Everyday eyeglasses only
have impact resistant lenses; they are not safety glasses. Also
use face or dust mask if cutting operation is dusty.
14. SECURE WORK. Use clamps or a vise to hold work when
practical. It's safer than using your hand and frees both hands
to operate tool.
15. DON'T OVERREACH. Keep proper footing and balance
at all times.
16. MAINTAIN TOOLS IN TOP CONDITION. Keep tools
sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
17. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, bits, cutters, etc.
18. USE RECOMMENDED ACCESSORIES. The use of
accessories and attachments not recommended by Delta may
cause hazards or risk of injury to persons.
19. REDUCE THE RISK OF UNINTENTIONAL START-
ING. Make sure switch is in “OFF” position before plugging in
power cord.
20. NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is accidentally contacted.
21. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be carefully
checked to ensure that it will operate properly and perform its
intended function - check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or replaced.
22. DIRECTION OF FEED. Feed work into a blade or cuttter
against the direction of rotation of the blade or cutter only.
23. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
POWER OFF. Don't leave too! until it comes to a complete
stop.
24. DRUGS, ALCOHOL, MEDICATION. Do not operate tool
while under the influence of drugs, alcohol or any medication.
25. MAKE SURE TOOLIS DISCONNECTED FROM POWER
SUPPLY while motor is being mounted, connected or
reconnected.
26. WARNING: The dust generated by certain woods and
wood products can be injurious to your heaith. Always operate
machinery in well ventilated areas and provide for proper dust
removal. Use wood dust collection systems whenever possible.
ADDITIONAL SAFETY RULES
FOR BAND SAWS
1. WARNING: Do not operate your band saw until it is
completely assembled and installed according to the
instructions.
2. IF YOU ARE NOT thoroughly familiar with the opera-
tion of band saws, obtain advice from your supervisor,
instructor, or other qualified person.
3. ALWAYS WEAR EYE PROTECTION.
4. NEVER turn the machine “ON” before clearing the
table of all objects (tools, scrap pieces, etc.).
5. NEVER startthe band saw with the workpiece contact-
ng the saw blade.
6. ADJUST the upper guide assembly about 1/8" above
the material being cut.
7. MAKE SURE the blade tension and blade tracking are
properly adjusted.
8. ALWAYS keep hands and fingers away from the
blade.
9. CHECK for proper blade size and type.
10. DO NOT attemptto saw stock that does not have a flat
surface, unless a suitable support is used.
11. HOLD material firmly against the table and feed into
blade at a moderate speed.
12. TURN OFF machine if the material is to be backed out
of an uncompleted cut.
13. MAKE “release” cuts before cutting long curves.
14. DO NOT remove jammed cut-off pieces until blade
has stopped.
15. STOP the machine before removing scrap pieces from
the table.
16. NEVER perform layout, assembly, or set-up work on
the table while the machine is operating.
17. ALWAYS hold the workpiece firmly against the table.
18. AVOID awkward hand positions where a sudden slip
could cause a hand to move into the blade.
19. DO NOT cut material that is too small to be safely
supported.
20. MAKE SURE the blade teeth point downward toward
the table.
21. ALWAYS maintain proper adjustment of blade ten-
sion, blade guides, and blade support bearings.
22. SHUT OFF the power and clean the table and work
area before leaving the machine.
23. SHOULD any part of your band saw be missing,
damaged, or fail in any way, or any electrical component fail
to perform properly, shut off switch and remove plug from
power supply outlet. Replace missing, damaged, or failed
parts before resuming operation.
24. THE USE of attachments and accessories not recom-
mended by Delta may result in the risk of injuries.
25. MAINTAIN proper adjustment of blade tension, blade
guides, and thrust bearings.
26. ADDITIONAL information regarding the safe and proper
operation of this product is available from the National
Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-
3201, in the Accident Prevention Manual for Industrial
Operations and also in the Safety Data Sheets provided by
the NSC. Please also refer to the American National
Standards Institute ANSI 01.1 Safety Requirements for
Woodworking Machinery and the U.S. Department of
Labor OSHA 1910.213 Regulations.
27. SAVE THESE INSTRUCTIONS. Refer to them often
and use them to instruct others.
UNPACKING AND CLEANING
Carefully unpack the band saw and all loose items, as illustrated in Fig. 2, from the carton.
Remove the protective coating from the machined surface of the table. This coating may be removed
with a soft cloth moistened with kerosene.
DANGER: DO NOT USE ACETONE, GASOLINE OR LACQUER THINNER FOR THIS PURPOSE.
After cleaning, cover table surface with a good quality paste wax.
ASSEMBLING THE STAND
1. Assemble the stand as shown in Fig. 2, using
32-3/4 inch-long carriage bolts, flat washers and hex nuts
supplied.
2. Assemble rubber foot (A) Fig. 2, to each leg (B).
3. Assemble two 31 inch-long tie bars (C) Fig. 2, with
flanges up to the center of each stand leg (B) using eight
carriage bolts, flat washers and hex nuts (D). NOTE: Do not
completely tighten hardware at this time.
4. Loosely assemble two 18 inch-long tie bars (E) Fig. 2,
with flanges up, to the center of each leg (B), using eight
carrriage bolts, flat washers and hex nuts.
5. Assemble two 12 inch-long tie bars (F) Fig. 3, with
flanges up, to the top of stand legs (B) using eight carriage
bolts, flat washers and hex nuts (D). NOTE: Do not tighten
hardware at this time.
6. Loosely assemble two 24 inch-long tie bars (G) Fig. 3,
with flanges up, to stand legs (B) using eight carriage bolts,
flat washers and hex nuts (D). IMPORTANT: FLANGES
OF TIE BARS (G) SHOULD REST ON TOP OF TIE
BARS (F).
7. Before tightening hardware (D) Figs. 2 and 3, place
stand in upright position and press down on stand until legs
adjust to floor surface. Securely tighten all hardware.
ASSEMBLING
BAND SAW TO STAND
1 Place stand in the upright position.
2. Position the band saw on the stand as shown in Fig. 4,
and fasten using four 5/16-18 x 1-1/2" hex head screws,
three of which are shown at (A), eight flat washers and
four hex nuts.
Fig. 2
Fig. 4
FASTENING STAND
OR BENCH TO FLOOR
IF DURING OPERATION THERE IS ANY TENDENCY
FOR THE MACHINE TO TIP OVER, SLIDE OR WALK ON
THE SUPPORTING SURFACE, THE STAND OR BENCH
MUST BE SECURED TO THE FLOOR.
ASSEMBLING
TABLE INSERT
1. Loosen knob (A) Fig. 5, and raise upper blade
guide (B).
2. Position table insert (C) Fig. 6, in saw table as shown.
ASSEMBLING GUIDE RAIL
AND RIP FENCE
1. Thread clamp knobs (A) Fig. 7, into tapped holes in
underside of saw table.
2. Position guide rail (B) as shown in Fig. 8, against clamp
knobs (A) and tighten clamp knobs.
Fig. 7
3. Assemble rip fence (C) Fig. 9, to guide rail (B) and
tighten clamp knob (D). NOTE: The rip fence may be
positioned either to the right or to the left of the saw blade.
IMPORTANT: The rip fence (C) Fig. 9, should be parallel
to the miter gage slot (E). If it is necessary to make an
adjustment, loosen two hex head screws (F) Fig. 9, and
adjust body of rip fence so that it is exactly parallel to the
miter gage slot (E). Then tighten two hex head screws (F).
Fig. 6
Fig. 9
CONNECTING SAW TO POWER SOURCE
POWER CONNECTIONS
A separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should
be protected with a 20 Amp fuse. Have a certified electrician replace or repair a worn cord immediately. Before
connecting the motor to a power line, make sure the switch is in the “OFF” position and be sure that the electric
current is of the same characteristics as stamped on the motor nameplate. Running on low voltage will damage
the motor.
WARNING: DO NOT EXPOSE THE TOOL TO RAIN OR OPERATE THE TOOL IN DAMP LOCATIONS.
MOTOR SPECIFICATIONS
Your saw is wired for 110-120 volt, 60 HZ alternating current. Before connecting the saw to the power source,
make sure the switch is in the “OFF” position.
‘GROUNDING INSTRUCTIONS
CAUTION: THIS TOOL MUST BE GROUNDED WHILE IN USE
TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.
‘In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped with
an electric cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into a
matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
‘Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
‘Improper connection of the equipment-grounding con-
ductor can result in risk of electric shock. The conductor
with insulation having an outer surface that is green with or
without yellow stripes is the equipment-grounding con-
ductor. If repair or replacement of the electric cord or plug
Is necessary, do not connect the equipment grounding
conductor to a live terminal.
‘Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE IS A
LONGEST OF THE 3 BLADES
JT)
Fig. 10
‘Use only 3-wire extension cords that have 3-prong ground-
ing type plugs and 3-hole receptacles that accept the tool's
plug, as shown in Fig. 10.
Repair or replace damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet
and a plug that looks like the one shown in Fig. 10.
À temporary adapter, which looks like the adapter illus-
trated in Fig. 11, may be used to connect this plug to a
2-pole receptacle, asshownin Fig. 11, if a properly grounded
outlet is not available. The temporary adapter should
be used only until a properly grounded outlet can be
installed by a qualified electrician. THIS ADAPTER IS NOT
APPLICABLE IN CANADA. The green-colored rigid ear,
lug, and the like, extending from the adapter must be
connected to a permanent ground, such as a properly
grounded outlet box, as shown in Fig. 11.
"CAUTION: IN ALL CASES, MAKE CERTAIN THE RE-
CEPTACLE IN QUESTION IS PROPERLY GROUNDED.
IF YOU ARE NOT SURE HAVE A CERTIFIED ELEC-
TRICIAN CHECK THE RECEPTACLE.
GROUNDED OUTLET BOX
GROUNDING MEANS N
ADAPTER —
Fig. 11
EXTENSION CORDS
Use proper extension cords. Make sure your extension
cord is in good condition and is a 3-wire extension cord
which has a 3-prong grounding type plug and a 3-pole
receptacle which will accept the tools plug. When using an
extension cord, be sure to use one heavy enough to carry
the current of the band saw. An undersized cord will cause
a drop in line voltage resulting in loss of power and
overheating. Fig. 12, shows the correct size to use depend-
ing on cord length. If in doubt, use the next heavier gage.
The smaller the gage number, the heavier the cord.
ON/OFF SWITCH
The switch (A) Fig. 13, is located on the arm of the band
saw. To turn the saw ON, move the switch to the “up”
position. To turn the saw OFF, move the switch to the
“down” position. WE SUGGEST THAT WHEN THE SAW
IS NOT IN USE, THE SWITCH BE LOCKED IN THE
“OFF” POSITION. This can be done by grasping the switch
toggle (B) and pulling it out of the switch. With the switch
toggle (B) removed, the switch will not operate. However,
should the switch toggle be removed while the saw is
running, the saw can be turned OFF once, but cannot be
restarted without inserting the switch toggle in the switch.
TOTAL LENGTH OF
GAGE OF EXTENSION
CORD IN FEET CORD TO USE
0 - 25 16 AWG
26 - 50 16 AWG
51 - 100 14 AWG
101 - 150 12 AWG
Fig. 12
OFF
REMOVE
ee
Fig. 13
OPERATING ADJUSTMENTS
Your band saw was checked and adjusted at the factory; however, itis always a good idea
to check the adjustments yourself. The following instructions will assist you.
ADJUSTING BLADE TENSION
With the saw blade centered on the three wheels, turn the
knob (A) Fig. 14, clockwise to increase blade tension or
counterclockwise to decrease blade tension until fiber
washer (B) lines up with corresponding blade width on
scale (C) Fig. 14.
The scale is correct for average work, and is not
affected by use of re-brazed saw blades. We urge you
to use this scale until you have become familiar enough
with the operation of the band saw to vary the tension
a little for different kinds of blades or work. Over-
tensioning is a common cause of blade breakage and
unsatisfactory blade performance. When the band saw
is not in use, it is good practice to release tension to
prolong the life of the blade.
e г
==
=
=
p=
=
==
=a]
fe
LN
Fig. 14
TRACKING THE BLADE
For accurate work and maximum blade life, it is important
that the blade be centered on the rear wheel. When this
adjustment is properly made, the blade will “track,” that is,
it will run steadily in the same line. To “track” the blade,
proceed as follows:
1. Disconnect the saw from the power source.
2. Make sure the correct blade tension is applied to the
saw blade.
3. Unscrew three knobs (A) Fig. 15, and remove the front
cover (B).
4. Position both the upper and lower blade guides away
from the blade (see “ADJUSTING UPPER AND LOWER
BLADE GUIDES”).
5. Turn the rear wheel (C) Figs. 16 and 17 slowly by hand
to determine if the blade (D) is riding on the center of the
wheel as shown in Fig. 17.
6. If the blade is not riding on the center of the wheel,
loosen wing nut (E) Fig. 17, and while turning the rear wheel
by hand, turn the thumb screw (F) Fig. 17, slightly clockwise
or counterclockwise. You will notice that the saw blade will
move to the right or the left on the wheel. Never run the saw
to track the blade with the front cover removed.
7. Whenthe blade is riding on the center of the rear wheel,
tighten wing nut (E) Fig. 17.
8. Replace front cover that was removed in STEP 3.
9. Plug in the saw and jog the motor switch ON and OFF
to be certain that the blade is tracking properly.
Fig. 16
ADJUSTING UPPER
BLADE GUIDE ASSEMBLY
The upper blade guide assembly (B) Fig. 18, should always
be set about 1/8" above or as close as possible to the top
surface of the workpiece being cut. Loosen knob (A)
Fig. 18, and position the guide assembly (B) to the desired
position.
ADJUSTING UPPER AND
LOWER BLADE GUIDES
The blade guides must be properly adjusted to prevent the
blade from twisting during operation. The upper blade
guides and blade support bearing should be adjusted only
after the blade is tensioned and tracking properly. To
adjust, proceed as follows:
1. DISCONNECT THE SAW FROM THE POWER
SOURCE.
2. The upper guide bracket (A) Fig. 19, is assembled to
the lower end of the guide post (B) by a hex head screw.
Loosen the hex head screw and move the guide bracket (A)
in or out until the front edge of the guides (C) are just behind
the blade “gullets” (bottom of the saw teeth).
3. The lower guide bracket (D) Fig. 20, is assembled to
the frame casting using a flat head bolt and hex nut. Loosen
the hex nut and move the guide bracket (D) in or out until
the front edge of the guides (E) are just behind the blade
“gullets.”
4. The upper blade guides (C) Fig. 19, and lower blade
guides (E) Fig. 20, are held in the guide brackets with set
screws (F). Loosen set screws (F) and adjust blade guides
as close as possible to the sides of the saw blade being
careful not to pinch the saw blade.
ADJUSTING BLADE
SUPPORT BEARINGS
The upper blade support bearing (G) Fig. 19, and lower
blade support bearing (H) Fig. 20, prevent the saw blade
from being pushed back too far while cutting, which could
damage the set in the saw teeth. The support bearings (G)
Fig. 19, and (H) Fig. 20, should be adjusted approximately
1/64" behind the blade, as follows:
1. Loosen thumb screw (J) Fig. 19, and position upper
blade support bearing (G) 1/64" behind the rear edge of the
saw blade. Tighten thumb screw (J).
2. Loosen thumb screw (K) Fig. 20, and position lower
blade support bearing (H) 1/64" behind the rear edge of the
saw blade. Tighten thumb screw (K).
TABLE ADJUSTMENTS
The table can be tilted 45 degrees to the right and approxi-
mately 3 degrees to the left. To tilt the table, loosen large
wing nut (A) Fig. 21, and tilt the table to the desired position
on scale (B). Tighten large wing nut (A) Fig. 21.
The band saw is equipped with a positive stop that positions
the table 90 degrees to the blade. To check and adjust,
proceed as follows:
1. Loosen large wing nut (A) Fig. 21. Position the table so
that line (C) points to the “0” degree mark on scale (B) and
tighten large wing nut (A).
2. Place a square on the table and against the saw blade,
as shown in Fig. 22. Check to see if the table is at 90
degrees to the saw blade. If it is not, loosen large wing nut
(A) Fig. 21, and move the table until you are certain the table
is at 90 degrees to the blade. Tighten large wing nut (A).
3. Loosen two screws (D) Fig. 21, and adjust scale (B) so
that line (C) points to the “0” degree mark.
4. Loosen locknut (E) Fig. 21, and turn the stop screw (F)
in or out so that it contacts the frame casting when the table
is at 90 degrees to the saw blade. Hold the stop screw (F)
at this position and tighten locknut (E) Fig. 21.
5. Ifyou desire to tilt the table to the left, the stop screw (F)
Fig. 21, and locknut (E) must be removed.
BLADES
OPERATION WIDTH — [THICKNESS] PER INCH | _ TYPE
For all wood and light, non-ferrous metals. Cuts to 1/4" radius. 1/8" .018 15 Fine scroll
For all wood and light, non-ferrous metals. Cuts to 1/2" radius. 3/16" ‚020 6 Skip tooth
For all wood and light, non-ferrous metals. Cuts to 7/8" radius. 1/4" .020 6 Skip tooth
For coarse, soft woods and wood 1/2" and thicker. Cuts to 1-1/2" radius. 3/8" ‚020 4 Skip tooth
For cutting most steel and foundry metals, less than 1" thick. 3/8" .020 24 Metal cutting
For cutting most steel and foundry metals, 1" thick and over. 3/8" .020 18 Metal cutting
Fig. 23
Always use a sharp blade. Keep it free from gum and pitch.
Keep the rubber tires free of sawdust and gum and pitch
accumulation. Clean frequently with a stiff fiber brush.
Narrow blades are used for cutting small circles or curves
while the wider blades are best suited for straight cutting
such as ripping (see blade chart Fig. 23).
Due tothe low costofbladesit is advisable to purchase new
blades rather than attempt to have them sharpened.
10
Make sure the blade guides are always adjusted properly
as previously outlined.
Do not force or twist the blade around a curve or a very
short radius.
Feed the work uniformly allowing the blade to cut — do not
feed too fast.
Do not apply excessive tension on blades. The tension is only
necessary to drive the blade without slipping on the wheels.
Narrow blades require more tension than wider blades.
REMOVING AND
INSTALLING THE BLADE
1. Disconnect the band saw from power source.
2. Remove the front cover of the band saw.
3. Remove the fence guide rail (A) Fig. 24, and table
insert (B).
4. Release blade tension and remove blade as shown in
Fig. 25.
5. Check new blade to be sure teeth will point down
towards table when installed. If not, turn blade inside out.
6. Place the blade on the wheels and adjust tension,
guides and tracking as previously described.
7. Replace table insert, guide rail and front cover.
WOOD/METAL CUTTING
CHANGE-OVER
1 Disconnect the machine from the power source.
2. Remove fence guide rail, table insert, front cover and
existing saw blade.
3. Using hex key wrench (A) Fig. 26, supplied with band
saw, remove button head screw (B) and retainer (C).
4. Removedrive wheel (D) Fig. 27, and wood cutting drive
belt (E).
11
Fig. 24
5. Position metal cutting drive belt (F) Fig. 28, over driven wheel (G) and stretch drive
belt over arbor (H). Turn driver wheel (G) by hand to insure drive belt runs true on both the
wheel and arbor.
6. Reassemble retainer (C) Fig. 29, and button head screw (B). Tighten screw (B)
securely.
7. Assemble the desired metal cutting blade as described under “REMOVING AND
INSTALLING THE BLADE.”
LUBRICATION
Lubricate the wheel bearings by applying a light machine oil
in the shaft holes (A) Fig. 30, each time saw blade is re-
placed or each time front cover is removed.
The blade support bearings are prelubricated and do not
require further lubrication.
MITER GAGE
A miter gage is supplied with your band saw to provide
cross-cutting capability at 90 degrees and up to 45 degrees
left and right. Fig. 31, illustrates using the miter gage to
make a cross-cut.
12
1. To operate the miter gage, loosen clamp knob (A)
Fig. 32, and position the gage body at the desired angle.
Then tighten clamp knob (A).
2. To adjust the miter gage, set the miter gage body (B)
ig. 32, so that pointer (C) is at the 90 degree mark, as
shownin Fig. 32. Make a cut on a scrap piece of wood. Then
check the piece of wood with a square to see if it was cut at
90 degrees. If the piece of wood was not cut at 90 degrees,
adjust the miter gage body (B) Fig. 32, until you are certain
you have made a 90 degree cut. Then set pointer (C) to the
90 degree mark.
= a
L =
Pl
KT
e
Fo
ы a Sr
e (=)
Ce rr adi By Tan
RIP FENCE
The rip fence can be used to position and guide the work
when making a lengthwise cut through a board, as shown
in Fig. 33. Since the board is guided along the fence, it must
have a straight edge and should make solid contact with
the table.
With the addition of a wood facing (A) Fig. 34, the fence can
be used as a cut-off gage when doing repetitive cross-
cutting using the miter gage. The wood facing can be
attached to the fence with a wood screw inserted through
the hole provided in the fence. When using a wood facing
on the fence for cut-off gage purposes, the wood facing
should stop short of the saw blade, as shown in Fig. 34. The
facing must not extend beyond the blade.
13
AUTHORIZED SERVICE STATIONS
In order to promote tool safety, Delta International Machinery Corp. strictly enforces the policy of repairing or replacing any damaged or missing standard safety
equipment on machines presented to Delta Authorized Service Centers for service/repairs. Any product which is presented to a Delta Authorized Service Center
for repairs which contains missing or damaged standard safety equipment will have that equipment repaired or replaced and the customer will be charged for any
such service/repairs. Customers can avoid such charges only if the missing safety component is supplied to the service center at the time of repair.
ALABAMA
Burningham 35208
Alabama Jack Co, inc.
1140 5h Avenue North
205-251-8158
907-562-6151
Fairbanks 99706
Fairbanks Asm Sannces, Inc.
Box 60590
907-479-5655
602-745-1100
Tucson 657 19
Westem Tool inc.
702 50. Campbell
602-884-0504
1419 West 10th Street
501-374-5180
CAC Machinery Inc.
2120 E. 2nd Street
501-068-7144
Springdale 72765
Layman's Hardware & Supply Inc.
E Emma Ave,
501-750-5067
CALIFORNIA
Burbank 91504
Rodman & Company
2823 N. San Femando Road
818-845-5454
415-827-1011
Fax: 415-827-5408
“IND. MACHINERY SERVICE
Califomia Electric Service
9744 Sierra Avenue
609-355-2500
Fresno 93703
A4 A Machinery & Electric inc.
1919 E. Home Avenue
209-233-1213
Fullerion 52631
Cabomia Electric Service
Center
1208 E. Ash Avenue
T14-870-0900
Huntingion Beach 92649
Modem Tool Service
15561 Product Lane Uni 0-6
714-856-3425
Mission Viejo 92691-3128
Caldoma Electric Service
23725 Via Fabricante, Una B
714-586-5440
Fax: 714-586-0514
Modesio 9535 1
Stanislaus Electric Mtr, Works
504 Féver Fond
National City 92050
Nail. Tool A Machy. Repair, Inc.
241 W. 35h 51. STE D
619-422-8665
North Hollywood 91605
Bucknall Power Tool Sanvica
11910 Vose Streei
B18-765-0278
Cakland 94606
Califomia Electric Service, Inc.
1143 E. 12th Street
415-834-1050
Fac: 415-836-1125
Fax: 518-792-0511
Redding 96002
Electric Tool and Motor
915 Wall Street #1
916-222-1131
Valley Tool Repair
4131 El. Power inn Acad
916-737-6300
San Bamardino 92408
Battels Hardware 4 Tool Co
473 5. Waleman Avenue,
Suite H
Corporation
3039 Teagarden Street
P.O. Box 1913
510-357-8762
San Marcos 92069
Pro-Tek Tool Repair
215 Pacific Street, #111
610-471-4800
Fax; 714-641-2847
Santa Barbara 83101
Buena Tool Co.
1806 Empire Industrial Court #0
707-528-1111
Sami Valley 93063
Simi Tool Repai
2512 Tapo Street
805-584-5138
Temecula 97390-5623
Calfomia Electric Service
41715 Enterprise Circle North
309-605-5445
Universal Tool Service
21804 5, Vermont Avenue
310-225-6472
Wan Nuys 91411-1018
Calidomia Electric Senvica
14753 Cunard Street
818-997-8855
Fax: 818-897-3047
Whittier 0602
Battels Hardware A Tool Co.
13238 E. Whittier Blvd,
310-696-3714
W. Los Angeles 90064-2110
Calitomæ Electric Service
719-638-1311
Denver 80204
Porter-Cable Corporation
2561 West Bit Ave.
206-892-5113
Denver 80219
"Schlosser Tool & Machinery
201 Bryant Street
203-022-8244
Grand Junction 81501
Professional Tool Service, inc.
2420 E. Main
303-245-3158
CONNECTICUT
Hartord 06106
Utily Electric Service, Inc.
53 Main Street
203-246-7271
Oakville 06779
Wateriown Tool Supply
28 Main Street
203-506-1344
Fi. Lauderdale 33334
Master Inc.
4107 H.E. Bth Avenue
305-566-5833
FL. Myers 33905
Power Tool Repair of FL. Myers
9950 Orange Finer Blvd,
813-694-6058
Gasnesville 32606
Florida Fasiener and Tool Ca,
Inc
2826 N. Waldo Road
904-377-4587
Hialeah 33014
Porter-Cable Corporation
16373-75 NW 571h Ave.
205-624-2523
Jacksonville 37205
North Fiorda Machinan & Tool
Rapair
284 5. Edgewood Ave.
904-387 -4455
Naples 33441
"West Coast Saw, Inc.
2825 Davis Bivd
B13-774-2525
Ortando 328068
5-Tek Power Tools, Inc.
3434 South Orange Avenue
407-851-5642
Crlando 32807
Florida Electro Mechanical Inc.
420C Gaston Foster Road
407-282-5367
251-H2 Lalo Street
96793
Sam's Power Tools, inc.
864 Alua Street
B08-242-7878
IDAHO
Boise 63705
Air Equipmant Company
Z350 South Orchard Street
208-342-2464
Boise B3706
Addison (Chicago) 60101
Porter-Cable Corporation
311 Laura Drive
708-628-6100
14
Mt. Vemon 69864
Holz Tool Supply
1306 Salem Road
618-242-4676
217-522-9115
INDIANA
Elkhart 46516
Thunander
Corporal
21861 Protécia Dr.
219-295-4131
Evansville 47710
Виком & Hubert
917-248-1444
Topeka 46571
Scarlet! Machinery of Indiana
BOGS W. 4005
219-593-2318
Warsaw 46580
Warsaw Tool Supply
113 W. Market St.
219-259-2004
IOWA
Cadar Rapids 52404
Puckett Tool & Fastener
410 181 Avenua MW
318-263-2211
Dés Moines 50309
Puckett Electric Tools, inc.
B41 11th Street
515-244-4180
Hiawatha
Janda's Tool Center
754 N. Canter Point Road
319-203-4740
lowa City 52240
Contraciors Tool
1430 Watarlront Driva
319-238-1121
KANSAS
Dodge City 67801-0179
Southwind Supply
1801 W. Frontview
316-225-4364
Manhatan 66502-9602
J E H Mowers & More Inc.
1616 Recreation Drive
813-537-4108
Overland Park 66214
"Overiand Tool
9119 Baron
913-596-4044
Escanaba 49829
Bosk Tool Service
918 North Lincoln Road
806-788-1112
Gaylord 49735
Graham Motor & Generator
Service Inc.
977 M, Center
517-732-5005
P.O. Box 12353
B16-221-2070
SA. Louis 63116
Porter
‘AUTHORIZED SERVICE STATIONS (continued)
Missoula 59801
Montana Tool Co.
1908 North Ave. West
406-721-6425
Whitefish 59937
Northwest Tool Repair
6466 Highway 93 South
406-862-6275
NEBRASKA
Lincoln 68504
Lincoln Tool Service Center
3535 North 40th Street
402-464-1157
Lincoln 68521
Tool Hospital
1720 Adams Street
402-435-2996
Omaha 68127
Thacker Electric
8507 | Street
402-592-9433
NAT WATS 800-878-7604
Omaha 68127
Tool Hospital
4690 So. 85 Street
492-592-5220
NEVADA
Las Vegas 89103
E & M Industrial Hardware
3725 West Russell Rd.
702-736-6102
Las Vegas 89109
Tool Service, Inc.
3229 Industrial Road
702-734-9161
Las Vegas 89118
Service Select Power Tool Repair
5720-A S. Valleyview Blvd.
702-739-1939
Las Vegas 89119
A-1 Equipment 4 Tool Repair
2520 E. Sunset Road
702-261-9680
Sparks 89434
Sierra Supply, Inc.
1830 E. Lincoln Way
702-353-3333
NEW HAMPSHIRE
Brentwood 03833
Brentwood Machine Sales inc.
Building #313 - Ate #125
603-679-8452
Keene 03431
Hamshaw Lumber
3 Bradco Street
603-352-6506
Nashua 03061
Hammar Industrial
175 Amherst St,
Р.О. Вох 1209
603-882-5161
NEW JERSEY
Roselle 07203
Tool & Machinery Service, inc.
419 East 1st Avenue
Somerville 08876
Butens }
Services Co.
10 County Line Road, Suite 7
908-707-0912
NEW MEXICO
Albuquerque 87107
Farmington 87401
Wastem Tool Crib
2601 East Main
505-325-4543
NEW YORK
Albany 12202
A. B. Wing á Son Corp.
460 South Pearl Street
518-563-4161
Albany 12206
Albany Bumer Control, Inc.
20 Colvin Avenue
518-459-8856
Amherst 14226
*Philipps Bros. Supply Inc.
2525 Kensingion Avenue
716-839-4800
Buffalo 14210
S 4 S Electric Repair Shop Inc.
2470 Seneca Street
716-823-1232
Commack 11725
*County Power Tool Sarvice, Inc.
237 Commack Rd.
516-499-5666
Flushing 11365
Porter-Cabie Corporation
175-25 Horace Harding Expwy.
718-225-2040
Glens Falls 12801
518-793-4104
" *IND. MACHINERY SERVICE
— Hunter 12442
Windham Equipment
А. 296 & 23 С
Beaches Comers
518-263-4577
Kingston 12401
Miron Bidg. Products, Inc.
C.P.O. Box 1598
Rt. #9W North
914-336-6000
Peekskill 10566
Peekskill Electric Motor
13 South Broad St.
914-797-4141
Port Chester 10573
Pelham Tool Co.
21 Abendrough Avenue
914-937-1771
Rochester 14608
Jackson Saw & Knife Co.
517 State Street
716-546-7485
Rochester 14608
O. G. Schwarz, Division of
Hanes Supply, inc.
430 Atlantic Avenue
716-482-9282
Southampton 11968
Richards Tool and Motor Repair
County Road 39 & N. Main St.
516-283-5130
Syracuse 13210
Syracuse industrial Sales
713 E. Fayette Street
315-478-5751
Uniondale 11553
*Enterprise Machinery Co., Inc.
825 Nassau Road
516-485-2804
Utica 13502
McQuade and Bannigan
1300 Stark Street
315-724-7119
607-729-5278
Watertown 13601
McQuade á Bannigan
124 Murroch Circle
315-788-2612
NORTH CAROLINA
Burlington 27215
Paynes Power Tool
2550 5. Mebane Street
910-227-1031
Charlotte 28209 —
Porter-Cable Corporation
43038 South Boulevard
704-525-4410
Greensboro 27405
Tool & Equipment Supply, Inc.
807 Huffman Street
919-275-6124
Jacksonville 28540
Toot Repair & Sharpening
Service
413 Marine Bivd.
910-455-3437
Raleigh 27604
Specialty Tool Service of
Raleigh Inc.
2420 Atlantic Ave.
919-833-5903
Wilmington 28405
M.F. McLean Enterprises
Rt. 6, Box 97
Qid Wrightsville Road
910-343-1775
Winston Salern 27106
Piedmont Power Mach. Srv. Inc.
4305J Enterprise Drive
910-759-2022
NORTH DAKOTA
Bismark 58501
Acme Electric Motor, Inc.
1008 Basin Avenue
701-258-1287
316 21st Street East
701-225-0766
Fargo 58103
Acme Electric Motor, Inc.
Grand Forks 58201
Acme Electric Motor, Inc.
1705 13th Avenue North
701-746-6481
Minot 58701
Acme Electric Motor, Inc.
525 20th Avenue S.E.
701-839-2263
OHIO
Barberton 44203
Viking Akron Tool & Supply Co.
2915 New Park Drive
1-800-362-0585
216-753-1063
“ Cincinnati 45210
Cincinnati Electric Repair
2023 Elm St.
513-621-2183
Cincinnati 45215
Pro Toot Service Inc.
1125 Glendaie-Miford Road
513-772-1490
Columbus 43212
"Columbus Hardware
944 W. 5th Avenue
614-204-8665
Columbus 43214
Porter-Cable ACorporation
4560 Indiancia Avenue
614-263-0929
Alpha (Dayton) 45301
Authorized Tool Service Co.
876 Orchard Lane
P.O Box 5
513-429-5693
Hartville 44632
Hartville True Value
940 W. Maple Street
216-877-3631
Holland 43528
Power Tool Sales & Service
6713 Angola Road
419-568-8665
Lima 45801
Lima Armature Works
142 E. Pear! St.
419-222-4010
Toledo 43613
Electric Tool & Equipment
3156 Upton Avenue
419-474-7537
Valley View 44125
Porter-Cable Corporation
Sweet Valley Business Park
Unit #18
216-447-9030
West Milton 45383
Conken Equipment Co.
4950 Frederick Garland Road
513-698-3363
Youngstown 44515
Stambaugh Thompson
3754 Henricks Road
216-792-9071
OKLAHOMA
Enid 73701
Enid Electric Motor
1406 N. 4th
405-234-8622
Oklahoma City 73109
Steve's Wholesale
2423 S. Walker
405-631-0352
Oklahoma City 73126
Whitton Supply Co.
1419 W. Reno
405-236-5561
Tulsa 74115
Steve's Wholesale Dist., Inc.
5342 E. Admiral Place
918-834-0991
OREGON
Eugene 97402
Jim's Tool Service
515 Wilson Street
503-344-1243
Fax: 503-344-1513
Toll Free: 1-800-327-2033
Grants Pass 97526
Machine Masters
508 N.E. “F” Street
503-479-8676
Klamath Falls 97601
Quality Tool Repair
836 Richmond Street
503-883-5870
Mediord 97501
Precision Power Tool Repair Inc.
2919 N. Pacific Highway
503-770-5541
Portland 97202
Professional Power Tool Repair
Inc.
2506 S.E. 8th Ave.
503-234-3734
Portland 97212
Continental Machine & Tool Inc.
51 N.E. Hancock
503-2
Redmond 97756
Dave's Tool Repair
2392-5 S. Highway 97
503-548-0510
PENNSYLVANIA
Allentown 18103
Curio Electric Repair
825 South 5th
215-432-9923
Bellefonte 16823
*Triangle Sido. Supply & Services
1076 E. Bishop St.
814-355-5885
Erie 16510
Erie Power Tool Service
2920 Buffalo Road
814-899-6419
Harrisburg 17109
Stationary Équipment Sales &
Service
P.O. Box 10242
Rear 3805 Ridgeway Rd.
717-545-8043
Kingston 18704
Total Services & Systems, Inc.
166 W. Union Street
717-287-2124
Lancaster 17601
Woodworker's World, Inc.
1509 Lititz Pike
717-299-5264
Monroeville 15146
Professional Tool Service
700 Seco Road
Monroeville Industrial Park
412-373-7440
Philadelphia 19107-2375
Ideal Tool & Equipment Service
140 N. 10th Street
215-925-0672
Philadelphia 19154
Porter-Cable Corporation
122685 McNulty Road
215-677-7800
Fax: 215-677-9908
Statingion 18080
Doward's Electric
4711 Main Street
215-767-8148
Willamsport 17701
“Hermance Machine
First & Campbell Street
717-326-9156
York 17402
General Tool & Repair, Inc.
2449 S. Queen Si.
717-741-9592
SOUTH CAROLINA
Columbia 29203
Mann Electric Repair Co.
3600 Main Strest
803-252-7777
Greanville 29609
Tool Shed
901 Pointsett Highway
803-233-6185
Mt. Pleasant 29464
Royall Ace Hardware
884 Ban Sawyer Blvd.
803-884-2551
Myrtle Beach 29577
Coastal Elec. & Rewinding
718 Bth Avenue N.
803-448-3586
Spartanburg 29302
u
113 Country Club Rd.
803-585-9326
SOUTH DAKOTA
Rapid City 57702
Stan Houston Equipment Co.
1210 Deadwood Avenue
605-348-1155
Sioux Falls 57702
Stan Houston Equip. Co.
501 S. Marion Road
605-336-3727
TENNESSEE
Chattancoga 37412
F & D Tool Service and Supply
4121 Ringgold Road
615-698-6454
Jackson 38301
Smith Tool Service
908 S. Highland Avenue
901-427-4012
Jamestown 38556
Kirby's Fixit
Р.О. Вох 147
120 N. Norris
615-879-7414
Knoxville 37914
Adrian Machine Tools
2900 Thom Grove Pike
615-522-8991
Knoxville 37918
Automated Controls
Technology, Inc.
4821 N. Broadway
615-688-3574
Memphis 38115
Bird Fasteners, Inc.
6920 Winchester Rd., #102
901-366-1748
15
615-242-8026
Nashville 37210
Power Tool Service of Nashville,
Inc.
1106 Elm Hill Pike
Suite #130
615-255-8227
TEXAS
Amaro 79107
Tascosa Tool Service
306 №. Fillmore
806-373-3474
Austin 78722
Hamilton Electric Works Inc.
3800 Airport Bivd.
512-472-2428
Austin 78758-5498
The Tool Box
9906A Gray Blvd.
512-836-5483
Corpus Christi 78405
Corpus Christi Power Tool á
Repair
3701 Agnes
512-883-1117
Corpus Christi 78405
Otto Dukes Machinery Co.
2588 Morgan Street
512-883-0921
Dallas 75220
Air & Electric Tool Co.
2326 Myrtle Springs
214-869-3277
Dallas 75220
Porter-Cable Corporation
10720 N. Stemmons Freeway
214-353-2996
El Paso 79902
Schlosser Tool 6 Machinery
1505 Wyoming
815-544-8665
El Paso 79905
C.L. North Co.
123 Chelsea Street
914-772-1469
Ft. Worth 76110
Air & Electric Tool Co, Inc.
3301 South Grove
817-921-0231
Houston 77008
*Circle Saw Builders Supply
2510 Ella Boulevard
713-864-8444
Houston 77055
Porter-Cable Corporation
West 10 Business Center
1008 Wirt Road
Suite 120
713-682-0304
Longview 75606
Eastex Welding
Box 3223
1232 W. Marshall
214-758-7327
Lubbock 79405
Lubbock Electric Co.
1108 34th Street
806-744-2336
Lubbock 79412
Caprock Equipment Service &
S
2112 50th St.
806-747-9177
Lufkin 75901
Maddux Building Materials
1603 Atkinson Drive
409-634-3369
McAllen 78501
Weslaco Tool
700 Ash Street
210-664-9156
Midland 79701
Midland Tool Specialty
918 S. Main Street
915-682-4647
Odessa 79761
Builder's Tool & Fasteners
713 E. 2nd Street
915-332-3511
San Angelo 76903
Frank's Electric
2621 Martin Luther King
915-655-8928
San Angelo 76904
Angelo Tool Co., Inc.
914 Arroyo Drive
915-944-8258
San Antonio 78205
Electric Motor Service
1514 E. Commerca
512-296-3462
San Antonio 78212
*Otto Dukes Machinery
600 San Pedro
210-224-5576
Sherman 75090
Texoma Tool Repair Co.
309 E. Houston Street
214-892-1510
- Texarkana 75501
Ray's Electric Motor Repair
922 Bowie Street
214-792-7031
Tyler 75702
Mason Machinery
1908 W. Erwin Street
214-592-6581
Waco 76710
Gross Yowell
3720 Franklin Drive
817-754-5425
Weslaco 78596
Weslaco Tool Co.
1221 West Expressway 83
210-968-3156
Wichita Falls 76301
817-322-8696
UTAH
84321
Tool Liquidator
839 N. Main
801-753-4256
Salt Lake City 84115
A.C. Too! and Service, Inc.
2990 South West Temple
801-487-4953
Sait Lake City 84115
*M & M Tool and Machinery
1773 5 300 W (Rear)
801-485-8200
Salt Lake City 84115
Schlosser Tool and Machinery
2199 S. West Temple
801-484-4242
VERMONT
Essex Junction 05451
Burlington Tool Repair
3 Kellog Road
802-872-0051
VIRGINIA
Christiansburg 24073
SPC United/Warren E. Smith
8
820 JK Park St.
703-382-5501
Fredericksburg 22401
Logan Electric Service Inc.
98 industrial Drive
703-898-8873
Fredericksburg 22404
Fredericksburg Hardware Co., Inc.
513 William Street
703-373-8383
Harrisonburg 22801
Rocking R Hardware
1030 S. High Street
703-434-9967
Norfolk 23517
Bryan Electric Co., Inc.
424 West 25th Street
804-625-0378
Norfolk 23502
"Henry Watke Co.
1161 Ingleside Road
804-855-1071
Richmond 23222
Staley Co., Inc.
2024 Chamberlayne Avenue
804-321-6595
Roanoke 24013
Roanoke Amature Co.
1108-1/2 Street S.E.
703-345-8741
Fife 98424
Tap Power Tool Service
1421 52nd Avenue East
206-922-5787
Port Angeles 98362
L & L Tools
1927 E. First St.
206-457-1116
Renton 98055
Porter-Cable Corporation
268 Southwest 43rd Street
206-251-6680
Spokane 99202
Spokane Power Tool
E. 801 Trent Avenue
509-489-4202
Yakima 98901
Cooper Electric Motor Service
205 S. 4th Avenue
509-452-9550
— WEST VIRGINIA
Huntington 25701
Lawter Electric Motor Co.
20? Adams Avenue
204-522-8297
Wheeling 26003
Kennedy Hardware
3300 McCulloch Street
304-233-3600
WISCONSIN
Green Bay 54301
Power Tool Service Co.
310 N. Webster Ave.
Р.О. Box 1343
414-437-2594
Green Bay 54304
“Bay Verte Machinery
1023 Ashwaubenon
414-336-7440
Kenosha 53144
Aetna Power Tool Service
{Ом. of Aetna Mig. Co.)
4622 - 68th Avenue
414-654-1170
LaCrosse 54603
A-Line Machine Tool Co.
800 Monitor St.
608-785-1515
Madison 53713
Electric Motors Unlimited
1000 Jonathan Drive
608-271-2311
Milwaukee 53222
Wisconsin Power Tool inc.
3122 North Mayfair Road
414-774-3650
Oshkosh 54901
*Kie & Pfeil Hardware
427 North Main
414-236-3340
Schofield 54476
RA. Miller Industrial Supply
303 Ross Avenue
715-355-7999
WYOMING
Casper 82601
Casper Saw Shop
147 S. McKinley
207-237-3279
SHING
Advanced Tool & Machine
Service (ATMS)
1933 Montana Avenue, N.E.
206-636-8670
PUERTO RICO
Aquadilla 00603
J.C.A. Enterprises, inc.
PR 111 South, Bidg. 531
BO, Victoria
P.O. Box 3879
809-891-1741
San Juan 00922
*Ferreteria Abraham Inc.
P.O. Box 11974
Capama His. Sta,
809-782-6023
Sierra Bayamon 00961
8 & M Eiectric Tool Repair
Center
Cale 49, Bloque 51
Casa ?7 Avenue West Main
809-787-2287
CANADA
Alberta
Calgary T2E 8L2
Bay #6, 2520-23 St. N.E.
403-735-6166
British Columbi
Bumaby V5A 4T8
8520 Baxter Place
604-420-0102
Manitoba
Winnipeg ASH 0H2
1699 Dublin Avenue
204-633-9259
Ontario
Mississauga L4V 1J2
6463 Northam Drive
416-677-5330
Guelph N1H 6M7
644 Imperial Road
519-836-2840
Otlawa K2A 3X2
613-728-1124
Quebec
Si. Laurent (МИ), Р.О.
H4R 1VB
1447, Bégin
514-336-8772
Ste. Foy GIN 4L5
Suite 202
2202 Hue Lavoisier
418-681-7305
0 00000000000000000009000000009000000090000090%
У
A DELTA
Delta Building Trades and Home Shop Machinery
Two Year Limited Warranty
Delta will repair or replace, at its expense and at its option, any Delta machine,
machine part, or machine accessory which in normal use has proven to be defective
in workmanship or material, provided that the customer returns the product prepaid
to a Delta factory service center or authorized service station with proof of purchase
of the product within two years and provides Delta with reasonable opportunity to
verify the alleged defect by inspection. Delta may require that electric motors be
returned prepaid to a motor manufacturer’s authorized station for inspection and
repair or replacement. Delta will not be responsible for any asserted defect which has
resulted from normal wear, misuse, abuse or repair or alteration made or specifically
authorized by anyone otherthan an authorized Delta service facility or representative.
Under no circumstances will Delta be liable for incidental or consequential damages
resulting from defective products. This warranty is Delta’s sole warranty and sets
forth the customer’s exclusive remedy, with respect to defective products; all other
warranties, express or implied, whether of merchantability, fitness for purpose, or
otherwise, are expressly disclaimed by Delta.
2000000000000000000000000000000000000000000000E
Printed in U.S.A.
">