RC8CQC™Appl
i
cat
i
onGui
de
LI
NKCabl
eSpecs
I
nt
egr
at
or
Suppl
i
edCAT6STPCabl
e
EI
A568A orEI
A568B(
Mi
n.30’t
o300’Max)
12345678
Ci
scoQuadcam
RJ45Pi
nout
12345678
Pi
n1
gG oBbO brBR
oO gBbG brBR
T568A
T568B
PPC01
8
1
’PowerCabl
e
RCCC0370.
3M
Angl
edUTPCabl
e
RCCC01
4[
2]
1
’Angl
ed
HDMICabl
es
W PS4848VDC
1
00240V~
4763Hz
PowerSuppl
y
I
mpor
t
ant
: Due t
o t
he power
demandsofCi
s
co’
sQuadCam,i
t
i
sbes
tpr
act
i
ce t
o ut
i
l
i
ze SCT’
s
pr
ovi
ded RCRKL™ r
acks
hel
ft
o
f
aci
l
i
t
at
event
i
l
at
i
on.
LI
NKCabl
e
Power
,Cont
r
ol
,Audi
o&Vi
deo
RC8CE™
RC8HE™
RCCH01
6
3’UTPCabl
e
Ci
scoTouch1
0
Et
her
net
/POE
*
Ci
s
coPr
ovi
ded*
Modul
eDi
mensi
ons
RC8CE™:1
.
625”
H x7
.
5”
W x4.
375”
D
RC8HE™:1
.
375”
H x9.
25”
W x5.
375”
D
RCCH001[
2]
3’HDMICabl
es
Ci
scoCodecPl
us,CodecPr
o&SX80
RC8-CQC™ Installation Instructions
Updated: 5/14/2020
Supporting the Cisco Quad Camera and
Cisco SX80, Plus & Pro Codecs
TEST YOUR SCTLink™ CABLE
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your
SCTLink™ wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1.
2.
3.
4.
5.
6.
7.
Test and verify your CAT6 STP or FUTP SCTLink™ cable for UTP 568A/568B. This cable must be between 30ft - 300ft.
The SCTLink™ cable between the RC8-CE module (transmitter) & RC8-HE module (receiver)
must always be a single, point-to-point CAT cable with no couplers or interconnections.
Connect the provided PowerSniffer to the Quad Camera end of your CAT6 STP or FUTP SCTLink™ cable.
Connect the other end of the SCTLink™ cable to the blue “SCTLink™” connection on the Head End module.
Connect the WPS-48 power supply to the Head End module.
Connect the WPS-48 power supply to AC mains.
If the SCTLink™ cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result, stop and re-terminate cable.
Once your SCTLink™ cable has been tested, please disconnect the WPS-48 power supply from the RC8-HE module,
and the PowerSniffer from the SCTLink™ cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Connect the camera-end cables:
1.
2.
3.
Connect the RCC-C014 HDMI cables between the Quad
Camera’s HDMI 1 & 2 connectors RC8-CE’s “HDMI 1” and
“HDMI 2” ports.
Connect the RCC-C037-0.3M UTP cable between the
Quad Camera’s RJ45 Ethernet port and the RC8-CE’s
Ethernet port.
Connect the PPC-018 power cable between the Quad
Camera’s power connector and the RC8-CE’s “12VDC
Output” port.
Connect the codec-end cables:
4.
5.
corresponding “HDMI Out 1 A” and “HDMI Out 2 A” port.
Connect the 3ft RCC-H016 UTP control cable between
the codec’s RJ45 camera Ethernet port and the RC8HE’s “Ethernet 1”.
Connect and Initiate the Extended System:
6.
7.
8.
Connect one end of your CAT6 STP/FUTP SCTLink™
cable to the RC8-HE module’s blue “SCTLink™” port.
Connect the other end of the CAT6 STP/FUTP SCTLink™
cable to the RC8-CE module’s blue “SCTLink™” port.
Connect the WPS-48 power supply to the RC8-HE.
Connect two 3 ft RCC-H001 HDMI cables between
the codec’s HDMI camera inputs and the RC8-HE’s
• ALLOW UP TO TWO MINUTES FOR THE QUAD CAMERA SYSTEM TO INITIALIZE •
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
MODULE
LED LABELACTIVE STATUSINACTIVE STATUS
RC8-CE
OK LED 1 & 2
Blinking Green (~1 second interval)
Blinking or Solid Red
RC8-HE
OK LED 1 & 2
Blinking Green (~1 second interval)
Blinking or Solid Red
RC8-HELINK LEDSolid BlueSolid Red or Dormant
RC8-HEHDCP 1 & 2Blinking GreenN/A
Cable Table - Part numbers, descriptions and functions of all SCT cables provided for the RC8-CQC™.
This kit is also inclusive of [1] RC-RKL™ Rack Shelf.
CABLEDESCRIPTIONFUNCTION
[2] RCC-C014
1’ HDMI Cables
Video connection between Quad Camera and RC8-CE module.
RCC-C037-0.3M 1’ Angled UTP Cable
Control connection (Ethernet) between Quad Camera and RC8-CE module.
PPC-018
1’ Power Cable
Power connection between Quad Camera and RC8-CE module.
[2] RCC-H001
3’ HDMI Cables
Video connection between the codec and RC8-HE module.
RCC-H016
3’ UTP Cable
Control connection (Ethernet) between the codec and RC8-HE module.
Power Supply Specifications (AC-Mains Side): Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum.
Turn-on Surge: Less than 60 amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 48VDC
power supply uses 2.80 amperes AC maximum. All specifications subject to change without notice.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • © SOUND CONTROL TECHNOLOGIES, INC
">
