Sharp | KB-6015KS | Installation manual | Sharp KB-6015KS Installation manual

Microwave Drawer
INSTALLATION MANUAL
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL
INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in
accord with the stated clearances and dimensions on pages 2 and 3. See Figures 1 and 2.
UNPACKING YOUR MICROWAVE DRAWER ...................2
ELECTRICAL OUTLET ...........................................4
IMPORTANT NOTES .............................................2
GROUNDING INSTRUCTIONS ...................................4
IMPORTANT SAFETY INSTRUCTIONS .........................2
DRAWER INSTALLATION .......................................4
CLEARANCES AND DIMENSIONS ..............................2
MODEL AND SERIAL NUMBER LOCATION ....................4
MICROWAVE DRAWER MEASUREMENTS ....................3
CARE, CLEANING AND MAINTENANCE ......................4
ANTI-TIP BLOCK ................................................3
1
MICROWAVE DRAWER
CLEARANCES AND DIMENSIONS
INSTALLATION MANUAL
UNPACKING YOUR MICROWAVE DRAWER
• Remove all packing
materials from inside
the Microwave Drawer.
DO NOT REMOVE
THE WAVEGUIDE
C OV E R , wh ich i s
located on the top of the
Microwave Drawer.
To reduce the risk of tipping, the Microwave
Drawer must be secured by a properly installed Anti-Tip
block.
Sealing
Surface
• This Microwave Drawer must be electrically grounded in
accordance with local codes.
Waveguide
Cover
• Make sure the wall coverings and the cabinets around the
Microwave Drawer can withstand the heat generated by the
Microwave Drawer.
Never leave children alone or unattended in
the area where a Microwave Drawer is in use. Never leave the
drawer open when the microwave is unattended.
• Remove the feature
Sealing
sticker, if there is one.
Surface
Check the drawer for
Oven
any damage, such as
Cavity
m isaligned or bent
d r awe r, d a m a ge d
drawer seals and sealing surfaces, broken or loose Microwave
Drawer guides and dents inside the cavity or on the front
side of the drawer. If there is any damage, do not operate
the Microwave Drawer and contact your dealer or a SHARP
AUTHORIZED SERVICER.
Stepping, leaning or sitting on the drawer
may result in serious injuries and can also cause damage to the
Microwave Drawer.
• Do not use the Microwave Drawer as a storage space.
This creates a potentially hazardous situation.
• Check that the time-of-day is in the display. If not, touch
Stop/Clear to prevent unintended use.
CLEARANCES AND DIMENSIONS
• Dimensions that are shown in Figures 1 and 2 must be used.
Given dimensions provide minimum clearance. Locate
electrical outlet in the shaded area in the upper left-hand
corner of the cutout.
IMPORTANT NOTES TO THE INSTALLER
• Read all of the Installation Manual before installing the
Microwave Drawer.
• Be sure to leave these instructions with the consumer.
• Contact surface must be solid and level. Pay special attention
to the floor on which the Microwave Drawer will sit. The
floor of the opening should be constructed of plywood
strong enough to support the weight of the oven (about 100
pounds).
IMPORTANT NOTES TO THE CONSUMER
• Check location where the Microwave Drawer will be
installed for proper electrical supply.
Keep this manual with your Operation Manual for future
reference.
• Your oven can be built into a cabinet or wall by itself or
under a specific electric wall oven listed below.
• Remove all packing material before connecting the electrical
supply.
• Observe all governing codes and ordinances.
• As when using any microwave oven generating heat, there are
certain safety precautions you should follow. These are listed
in the Operation Manual. Read all and follow carefully.
• Be sure your Microwave Drawer is installed and grounded
properly by a qualified installer or service technician.
IMPORTANT SAFETY INSTRUCTIONS
Electrolux
E30EW75DSS1
Kitchen Aid
KEBC107KBLO
Frigidaire
PLEB30S8CCC
Viking
DES0100
Wolf
S030F/S
• Be sure that the clearance of the floor between the wall oven
and the microwave drawer is a minimum of 2-inches.
If the information in this manual is not followed
exactly, a fire or electrical shock may result that could cause
property damage, personal injury or death.
• For updates of approved appliances that can be used adjacent
to the Microwave Drawer go to www.sharpusa.com.
• The microwave interior will easily accommodate a 9” x 13”
oblong dish or a bag of microwave popcorn.
2
INSTALLATION MANUAL
electrical outlet
location
MICROWAVE DRAWER MEASUREMENTS
(6")
2x4 AntiTip block
3 1/2"
5"
4"
28 7/16"
opening
14 3/4"
to bottom
of Anti-Tip
block
allow 1/4"
overlap
allow 3/4"
overlap
23 1/2"
min depth
36"
countertop
height
14 3/4"
opening
allow 3/4"
overlap
floor must
support
100 lbs.
allow 7/16"
overlap
84"
wall
cabinet
19"
to top of floor
optional wall oven
cutout illustrated
in sketch
electrical outlet
location
Figure 1
(6")
NOTE: Open Top
Cabinet illustrated
30" *
cabinet min.
2x4 Anti-Tip block
28 7/16"
opening
2" minimum
4"
14 3/4"
to bottom
of Anti-Tip
block
allow 1/4"
overlap
allow 3/4"
overlap
23 1/2"
min depth
Figures 1 and 2 contain many Microwave Drawer measurements
for reference when planning the drawerʼs location.
3 1/2"
5"
4 11/16"
28 1/8"
2"
14 3/4"
opening
allow 3/4"
overlap
allow 7/16"
overlap
floor must
support 100 lbs.
15"
14 19/32"
15"
auto drawer
opening
*19"
to top of floor
(recommended)
23 3/8"
30"
cabinet min.
Figure 2
Figure 3
1 13/16"
door thickness
30"
NORMAL INSTALLATION STEPS
ANTI-TIP BLOCK
ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS
To reduce the risk of tipping of the drawer, the Anti-Tip block
must be properly installed located 14 3/4-inches above the floor on
which the Microwave Drawer will sit. The 6-inch 2 x 4 Anti-Tip
block must be provided by the installer. See Figures 1, 2 and 4.
The Anti-Tip block prevents serious injury that might result from
spilled hot liquids.
(6")
2x4 AntiTip block
5"
Figure 4
3
If the Microwave Drawer is ever moved to a different location, the
Anti-Tip block must also be moved and installed. When installed
to the wall, make sure that the screws completely penetrate the
dry wall and are secured in wood or metal so that the block is
totally stable. When fastening, be sure that the screws do not
penetrate electrical wiring or plumbing.
INSTALLATION MANUAL
DRAWER INSTALLATION
ELECTRICAL OUTLET
(6")
electrical outlet location
2x4 AntiTip block
5"
4"
Figure 6
Figure 5
The electrical requirements are a 120 volt 60 Hz, AC only, 15
amp. or more protected electrical supply. It is recommended that
a separate circuit serving only this appliance be provided.
The drawer is equipped with a 3-prong grounding plug. It must
be plugged into a wall receptacle that is properly installed and
grounded. Should you only have a 2-prong outlet, have a qualified
electrician install a correct wall receptacle.
Parts Supplied
2. Carefully guide the drawer into the prepared
opening. Avoid pinching the cord between
the oven and the wall.
4 Screws
3. Slide the drawer all the way until the mounting flange is flush
with the face of the cabinet.
Note: If you have any questions about the grounding or electrical
instructions, consult a qualified electrician or service person.
4. Secure the drawer with the 4 screws supplied. See Figure 6.
MODEL AND SERIAL NUMBER LOCATION
GROUNDING INSTRUCTIONS
The name plate, including model and serial number, is located
on the faceplate behind the Microwave Drawer front.
This appliance must be grounded. The Microwave Drawer is
equipped with a cord having a grounding wire with a grounding
plug. It must be plugged into a wall receptacle that is properly
installed and grounded in accordance with the National
Electrical Code and local codes
and ordinances. In the event Permanent and Correct Installation
of an electrical short circuit,
3-Prong Plug
grounding reduces risk of
electric shock by providing
an escape wire for the electric
current.
Grounding Pin
– Improper use
of the grounding plug can result
in a risk of electric shock.
1. Place the drawer adjacent to the wall or
cabinet opening. Plug the power supply cord
into the electrical outlet.
CARE, CLEANING AND MAINTENANCE
Temporary Use
Refer to the Operation Manual for cleaning instructions.
Ground Receptacle Box
Grounding Adapter
BEFORE YOU CALL FOR SERVICE
Read theScrew
BEFORE YOU CALL and operating instruction sections
in your Operation Manual. It may save you time and expense.
Tab
for list
Grounding
Screw common occurrences that are not the result of
The
includes
defective workmanship or materials in this range.
3-Prong Receptacle
Ground Receptacle Box
Refer to the warranty in your Operation Manual for Sharpʼs
toll-free service number and address. Please call or write if you
have inquiries about your microwave product and/or need to
order parts.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TINSEB 417MRR0
PRINTED IN USA
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising