Allen-Bradley 140G-R Series Manuel utilisateur
PDF
Download
Document
Advertisement
Advertisement
Bul. 140G 140G-R LSIG microprocessor-based electronic release for 140G-R Sganciatore elettronico a microprocessore LSIG Elektronischer Mikroprozessor-Auslöser LSIG Déclencheur électronique à microprocesseur LSIG Relé electrónico con microprocesador LSIG Installation - Installazione - Instalación Instalação WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements). AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. (Seguire i requisiti NFPA70E). WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen Sie die Anforderungen nach NFPA70E). AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E). ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E). ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E). 警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してく ださい。適切なケース内に取付けてください。また、汚染物質がないことを 確認してください。(NFPA70Eの要件に従ってください) 警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备 箱内。防止接触污染物。符合NFPA70E要求) 2 1 140G-R OPTIONAL Screw LSIG LENGTH 10 mm (0.39" ) Label dia. 3 OPTIONAL Retaining plug tool Locking cover See DIR 1000529R0510 Screw Screw x2 LENGTH 20 mm (0.79" ) DIR 1000650R0502 Version 00 dia. 4 LENGTH 6 mm (0.24" ) If not part of replacement kit, a catalog number have to be listed dia. 3 LENGTH 8 mm (0.31") dia. 3 1 2 torque? LENGTH 6 mm (0.24" ) dia. 3 4 3 LENGTH 10 mm (0.39" ) 5 DIR 1000650R0502 Version 00 (2) dia. 3 7 6 torque? 8 9 1 2 10 11 torque? 1 1 2 LENGTH 8 mm (0.31") 2 DIR 1000650R0502 Version 00 (3) dia. 3 13 DIR 1000650R0502 Version 00 (4) K2 K21 K11 K12 K13 K14 K15 95P 98P W1 W2 W1 98P 95P K15 K14 K13 K12 K1 K11 W4 K21 W3 K2 T10 K1 T9 W4 T8 W3 T8 T7 T7 T10 T6 T9 T5 T6 T5 12 W2 14 DIR 1000650R0502 Version 00 (5) 15 In ≤ Iu LENGTH 20 mm (0.79" ) dia. 4 9.7 lb in 1.1 Nm Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/ sustainability-ethics/product-environmental-compliance.page Publication 140G-IN133A-EN-P - April 2015 DIR 1000650R0502 Version 00 (L8482) - Preliminary Copyright © 2015 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy. ">

Public link updated
The public link to your chat has been updated.
Advertisement